Get information from virtual hardware in Web mode

Similar Questions

• How to get information from web interface tables

  Hello
  
  How to get information from web interface tables
  
  as in the forms... Go to help-> Diagnostics-> review
  Block = SYSTEM field is LAST_QUERY.
  
  Kind regards.

  Salvation;

  Please see the paragraphs below:

  How to determine the Table and the name of the column to a field in a form in 11i [ID 259722.1]
  How to find the query that succeeded recently? [241628.1 ID]

  Respect of
  HELIOS

• Why can't get information from frequency of NI USB-5132

  Hello

  I use NI USB-5132 and try OR Scope example measure a library.

  I wonder why I can't get information from the input signal frequency.

  Thank you

  In the flexible Panel, you need to adjust the time/Div and, possibly, the Volts/Div to get a consistent result. Make a note of the settings.

  Based on what you used in the soft cover, you must change the parameters of the VI until you see a signal. If you don't see something here, then obviously you can not perform a measurement. Try other examples to see if you can capture at least the waveform.

• get information from the sms message

  How to get information from sms

  ex: 1. the sender's phone number

  2. sms text

  Check the interface messages and methods like getAddress(), text, getPayLoadText.

• currently still have PP CS5.5 & want to install on another office, understand that I can only use one at a time. don't have a CD, can I get information from the current installation and a link to download PP CS5.5?

  currently still have PP CS5.5 & want to install on another office, understand that I can only use one at a time. don't have a CD, can I get information from the current installation and a link to download PP CS5.5?

  Download & install instructions https://forums.adobe.com/thread/2003339 can help

  -includes a link to access a page to download the Adobe programs if you do not have a disk or drive

  Find your http://helpx.adobe.com/x-productkb/global/find-serial-number.html serial No.

• get information from inside a trigger of the other tables in the schema even

  Addendum:
  
  ... Sorry I forgot: Oracle Database 10g Enterprise Edition Release 10.2.0.4.0 - 64 bit
  
  *******************
  
  Hello
  
  I'm trying for a few hours to get information from inside a trigger to another table in the same pattern.
  
  My trigger is PSE_BKB. NUM_PHANTOM_BP
  
  I first tried a simple solution...
  
  
  CREATE OR REPLACE TRIGGER PSE_BKB. NUM_TR_PHANTOM_BP
  BEFORE DELETING, INSERTION OR UPDATE
  ON PSE_BKB. NUM_PHANTOM_BP
  REFERRING AGAIN AS NINE OLD AND OLD
  FOR EACH LINE
  DECLARE
  
  v_recht NUMBER (1): = 0;
  v_recht2 NUMBER (1): = 0;
  v_change_mitarbeiter NUMBER (1): = 0;
  v_recht_mitarbeiter NUMBER (1): = 0;
  v_typ varchar2 (20);
  v_obj_key varchar2 (11): = "gugus";
  v_ph_key varchar2 (11);
  -ph_key varchar2 (11);
  v_obj_keys varchar2 (4000): = ', ';
  
  anz_num NUMBER: = 0;
  anz_num_tmp NUMBER: = 0;
  anz_st_si NUMBER: = 0;
  
  
  BEGIN
  
  ...
  Select count (*)
  in anz_num
  of pse_bkb.num_objekt o
  where o.obj_key in
  (select distinct (ov.obj_key)
  of pse_bkb.num_objekt_verb ov
  where ov.phantom_key =: old.phantom_key
  )
  and o.typ = "NUM";
  
  ...
  
  Explanation: my trigger table is PSE_BKB. NUM_PHANTOM_BP.
  
  On the pse_bkb.num_objekt_verb of the table, I have a relationship 1: n to one or several object-key (field named obj_key!) on my referenced key: old.phantom_key. With this obj_key, I want to watch the weather, I have one or more lines in the table type num_objekt "NUM". So the internal selection gives me all the num_objekt_verb obj_key with my: old.phantom_key and with whom I count the number of lines I have on num_objekt with type "NUM".
  
  The problem is that the trigger does not see the table.
  
  I tried many variations.
  
  The latest version I tried was with a cursor inside the trigger definition as in the block of code below.
  
  For debugging purposes, I inserted a RAISE_APPLICATION_ERROR in the inner loop - see below. The v_obj_key variable is never defined, as in all the other variations, I tried-, I still see the predefined "gugus" in the declare section.
  
  It seems that oracle can not read other tables at this point. La: old.phantom_key is defined (in this simple example there would come a return obj_key).
  
  Thanks in advance for your help - and excuse my English.
  
  Trigger code:
  
  CREATE OR REPLACE TRIGGER PSE_BKB. NUM_TR_PHANTOM_BP
  BEFORE DELETING, INSERTION OR UPDATE
  ON PSE_BKB. NUM_PHANTOM_BP
  REFERRING AGAIN AS NINE OLD AND OLD
  FOR EACH LINE
  DECLARE
  
  v_recht NUMBER (1): = 0;
  v_recht2 NUMBER (1): = 0;
  v_change_mitarbeiter NUMBER (1): = 0;
  v_recht_mitarbeiter NUMBER (1): = 0;
  v_typ varchar2 (20);
  v_obj_key varchar2 (11): = "gugus";
  v_ph_key varchar2 (11);
  -ph_key varchar2 (11);
  v_obj_keys varchar2 (4000): = ', ';
  
  anz_num NUMBER: = 0;
  anz_num_tmp NUMBER: = 0;
  anz_st_si NUMBER: = 0;
  
  
  BEGIN
  
  
  Start
  declare
  
  cursor nums is
  
  Select obj_key
  of PSE_BKB.num_objekt_verb
  where phantom_key =: old.phantom_key;
  
  Start
  
  for the RC looping nums
  v_obj_key: = cr.obj_key;
  
  RAISE_APPLICATION_ERROR (-20099,' AGAIN 9 v_obj_key: ' | v_obj_key |) ': old.phantom_key ' | (: old.phantom_key);
  
  When the exit nums % NOTFOUND;
  
  Select count (*) in the pse_bkb.num_objekt anz_num_tmp where obj_key = v_obj_key and type = "NUM";
  anz_num: = anz_num + anz_num_tmp;
  end loop;
  
  end;
  end;
  
  Published by: user832075 on 14.01.2013 06:18

  The reason why you get count_n = 0 in tr_c is that there is no line in B with key_c = 17, to the moment you arrive at tr_c. The removal of B has already occurred, and since you're in a single transaction, the application for tr_c:

  select count(*)
    into   counter_n
    from   a aa
    where  aa.key_a in (select distinct(bb.key_a)
                        from   b bb
                        where  bb.key_c = v_ph_key
                       )
    and    aa.typ = 'n';
  

  'knows' that the row has been deleted then gets a number of 0.

  I added a set of instructions dbms_output to show the order in which triggers run, and that's what I get:

  SQL> delete from b_vw where key_a = 1 and key_c = 17 ;
  in trigger b_tr_vw
  In tr_b
  in tr_c
  delete from b_vw where key_a = 1 and key_c = 17
              *
  ERROR at line 1:
  ORA-20077: Remark: counter_n: 0 counter_s: 0 v_ph_key: 17 old.key_c: 17
  new.key_c:
  ORA-06512: at "OPS$ORACLE.TR_C", line 38
  ORA-04088: error during execution of trigger 'OPS$ORACLE.TR_C'
  ORA-06512: at "OPS$ORACLE.B_TR_VW", line 17
  ORA-04088: error during execution of trigger 'OPS$ORACLE.B_TR_VW'
  

  Thus b_tr_vw trigger is triggered first and deletes a B. trigger fires tr_b as part of this statement to remove and check against A, happening apparently so no error is triggered and succeeds the removal of B. Now tr_b_vw takes back control and deletes C. Since the B line which has key_c = 17 already deleted a control for counter_n > 0 and counter_s = 0 fails and raise you the-20002 error. Note that I'm assuming that the error of-20077 you lift is just to see the values and is not intended to be part of your actual code.

  Because I have really no idea what you're trying to accomplish here I can't offer a lot of advice that you might want to try entering two tr_c of the tr_b_vw trigger validation queries before deliver you the removal of b and put the counter_n > 0 and counter_s = 0 control under tr_b_vw to decide whether or not you want to remove.

  John

• How can I get information from performance on disc with vFoglight 6.5 latency?

  Can someone tell me where I can get info from performance on disc with vFoglight 6.5 latency?

  There are also alarms that deal with the latency of disk. You are looking for a report or dashboard? Check the alarm Viewer and define a filter on the "latency". This will show you all the current latency time, then you can explore the host or logical unit number that is having the problem.

• Get information from vCenters bound in a connected mode configuration

  I use get - vm against the vCenter that I am connected.  However this vCenter is tied with a few other vCenters mode.

  How can I use

  Get - vm

  so that it returns all virtual machines of vcenters in bound with that mode I am currently connected to?

  Thank you!

  The easiest way would be to use the AllLinked of the cmdlet Connect-VIServer switch.

  This requires to operate in "multiple".

• Get information from the low level of the Subvi ni5660

  A quick explanation of the problem: I need to create several VI just to return a value of the PXI-5660 (ex: Center frequency, Span, etc.) while the entries are only a "VISA" and one "error in.»

  Detailed explanation of problem: I need to create multiple VI that the properties 'Set' or 'Get' of the PXI-5660 module (ex: the Central frequency value, get frequency, etc...).  Each VI must have a VISA in/out and in/out Error, but the only other present in/out should be the property of game/called.  Global variables are not allowed.

  One of the biggest problems for me is that ni5660 drivers do not contain a property node.  I managed to (apparently) set some of the properties by feeding only a single entry in the icon 'configure ni5660 for spectrum', but the only tool that seems to be able to output all information is the icon «MT get Attributes»  The release of 'MT get Attributes' does not contain many of the properties that I need good output.

  I tried to use the icon 'MT get Attributes' linked to "ungroup by name" which has the value "handle receiver.handles.niScope" which feeds on the reference to a property niScope node, hoping that I would be able to obtain information through the niScope 5660 (it seems that ni5660 software uses the niScope on a lower level software ", correct me if I'm wrong).  This VI finished, when put online with the 'ni5660 Initialize.vi' and ' ni5660 Close.vi, ' returned the error (-1074135028) with the explanation 'ID attribute not recognized.' ""  (The error occurred on the property node in the Subvi "Get the Central frequency")

  The goal is to make the action of PXI chassis similar to a HP8563E Spectrum Analyzer.  With this in mind, the list of attributes that I will need in the end to set and get (the separate VI) are the following: Center frequency, Span, window, number of Points, resolution bandwidth, level of reference, mitigation and time sweep.

  I apologize for my (very probably) simple question, but endless (I only started programming in LabVIEW there about 2 weeks).  If someone would be able to point me in how to make apparently PXI-5660 current property settings from thin air, I would be very grateful.  If more information or details are needed, feel free to ask.

  Thank you

  zdunn wrote:

  ....

  but unfortunately, I'm still at a loss, how to create a VI that "calls" that same property back and the fate, while using only 'VISA In' and 'In Error' as inputs.

  Located on how silly that statement. You want to create a function where (for example) you want to set the resolution bandwidth and do not want to pass as a parameter the name of the instrument. You have created the programming language that is able to read minds?

  You can use a function where you can pass a parameter in (or use a function that retrieves a parameter) or do nothing at all with the instrument. It is more complicated than that.

  There are tutorials available that can help yu with LabVIEW to learn, but I think that there are certain fundamentals means.

  Edit: Sorry, I may have misunderstood. to query does not require an entry but I don't understand what you want to query. The parameters of the instrument are all under control stripped - a program you or any other writing. Unlike a GPIB instrument, there is no one '?' command to read a rear frame. It is assumed that you know how the instrument has been configured in the first place.

• Widget - getting information from a url

  Hello, first, please excuse my English is not very good...

  I'm developing a widget with SDK WIDGET and I have a question, I need to retrieve some information about the 1 page on php hosted on an external web server, but I do not find any function to call at this url, can someone help me?

  Example:

  I have a url such as: www.enterprise.com \open.php then the url of this one back to 1 or 0, I need to get this result.

  Kind regards! Sorry if it's a bubsy request but I am a novice.

  In my opinion, using AJAX is a style much more clean and organized the retrieval of content.

  AJAX also allows that it runs asynchronously, which means that you can do something else while you wait for the results to come back.

  In addition, AJAX can be used to remove the content, when you don't want it to be displayed to the user via an iframe.

• Get information from excel to Vm description script

  Hello

  I am interesting to do a special with powershell script (if possible) who can get a data in my excel file and put it in a custom field in the description of the virtual machine.

  
  In particular, I have a lot of vm (about 800) and I have all the data of them (description, installed etc...)  in an excel file and I would put them in a custom field created with Vsphere client. Is this possible with Powershell?

  I searched the Internet but I can't see vsphere excellent... export information to excel to vcenter/esx.

  The version of vsphere 4.1 is.

  
  Thank you

  If you have an as a .csv file:

  'VM', 'Name', 'Value '.
  "scomp0016", "CreatedBy", "unknown".
  "scomp0016", "CreatedOn", '2009-05-25 10:26:30 '
  'scomp0016', 'Function', 'print server '.
  'scomp0016', 'Owner', 'Search'

  Then, you can use the following script to import annotations in vSphere:

  Import-Csv -Path VMAnnotations.csv | Where-Object {$_.Value} | ForEach-Object {
    Get-VM $_.VM | Set-Annotation -CustomAttribute $_.Name -Value $_.Value
  }
  

  The description field is not an annotation. You can set the description field of a virtual machine with the whole-VM-command Description.

  Best regards, Robert

  Post edited by: RvdNieuwendijk

• Get information from the file for use in Action of PS

  I am trying to create an Action that adds text from a photo of an image metadata.

  When recording an Action, I could open the information file and copy the text and then paste the text from the image. However, when I replay the Action on another image, for example the text of the original photo is pasted, the Action does not save the copy and paste it to the Clipboard.

  How can I automate paste the title of the Document, Description and other similar texts on a picture?

  The larger goal is to create a Droplet use to process a large number of images exported from Lightroom. However, I have not been able to successfully create the first step of a PS action that does what I need.

  Thanks for any help with this problem.

  Old Photo from Photoshop Web Gallery function would be inspired by galleries that could include the Image title and Description that is stored in the metadata of the Image. My scripts SimpleViewer and WS-Slideshow Photoshop create Web Flash galleries that support also the title and description of the metadata of the image and EXIF and notice of copyright. only Copyright metadata are superimposed on the image that the rest of text is displayed by Flash player in the XML file built by Photoshop script using the metadata of images. Example http://www.mouseprints.net/SVNewZealand/ws-slideshow.html

• Get information from the Bank of Tables HZ

  Hi I mostly use CE_BANKS_V for the information of the Bank, but in case I want this HZ_PARTIES table information so how I can get because there is presented data of parties, people, etc.. i don't know which one I should mention to get only the condition information stores.
  
  Kind regards
  Shakeel Khan

  Hi Shakeel

  If you see the script for ce_banks_v, it uses the table hz_parties only. You can use the following query (this one is taken by the script of ce_banks_v only):

  Select * from
  hz_parties bankparty, hz_code_assignments bankca
  where
  bankparty.party_type = "ORGANIZATION".
  AND bankca.class_category = 'BANK_INSTITUTION_TYPE. '
  AND bankca.class_code IN ('BANK', 'CENTRE')
  AND bankca.owner_table_name = 'HZ_PARTIES. '
  AND bankca.owner_table_id = bankparty.party_id
  AND NVL (bankca.status, 'A') = "A".

  Thank you
  Serge

• How to get information from my old iPod to my mac

  I have an old iPod touch without the camera. It was on the manual settings and now I can't get my laptop to synchronize with it. I get this message "iTunes could not connect to the iPod"xxx"because an invalid response was received from the device." I tried to access from devices, but it just does not recognize. Anyone know how I can get it working with my laptop. Its fully functioning, play music and charge, but I cannot sync.

  Help, please. Thank you

  try to reset the unit.

  Learn how to reset your iPod - Apple Support

• Get information from change of color over time

  Hi all

  I am new to LabView and on this forum, so I hope I'm in the right subforum. If this isn't the case, it would be nice if a mod could move this thread.

  My problem is the following:

  Let's say I have a white spot I want to observe with a camera. The color of the spot turns green over time and I want to acquire the photo, as well as to get the color intensity of green increase developing countries over time. I do not know what features I need to use to get there. Can someone me hint in the right direction? I think that it is at least possible in LabView.

  Thank your all for your help.

  Best regards

  Tresdin

  I don't know what the best resource for IMAQdx pilots, I think that the examples that provide OR are pretty useful. Here's a simple VI which will tell you the average value of green of all the pixels in your image.