Get ON a single router VPN KS and GM

Similar Questions

• Router VPN 3005 and 7500

  Hi all

  Could you someboy help me on that?

  I have a network like this:

  Internet Internet

  | |

  router VPN - 3005

  |

  Internal

  I can set up Lan to Lan VPN 3005 and other PIX aside, but I can't ping internal network with the back of my internal network. I've already put the static route to the subnet of setbacks in the router and my subnet route internal VPN. What should I do? Thanks in advance.

  Banlan

  in fact the 3000 can do a ping will depend on your network-lists / lists access so that my not be a relevant question.

• Laptop starts sometimes, but most of the time I get the flashing single LED SHIFT NUMLOCK and caps lock.

  Presario CQ61-411WM

  OS is Windows 7

  Most of the time the laptop does not start upward and I get the only witness flashing Caps Lock and Num Loc.  However, if I'm persistent and keep trying the Start button it will start.  After that it starts everything works fine.  I can even do a reboot and it will stop and start up.  But if I make a stop so I have to press the start several times (it will come back with the only witness flashing Caps Lock and Num Loc) before it will start again.

  Any suggestions?

  Buddy,

  The system does not close completely to the bottom of all components during a restart.

  When you can get your backups done, you could do some tests on the material.

  You can do a search using your favorite search engine to learn more about sleep verses shutdown.

  For example: Shut Down versus sleep against Hibernate

  Click on the Thumbs-Up Kudos to testify and say thank you.

  Although I strive to reflect best practices of HP, I do not work for HP.

• Between asa 5510 and router VPN

  Hello

  I configured ASA 5510 to vpn LAN to LAN with router 17 857. and between the routers.

  between vpn routers works very well.

  from the local network behind the ASA I can ping the computers behind routers.

  but computers behind routers, I cannot ping PSC behind ASA.

  I have configured the remote access with vpn cisco 4.X client, it works well with routers, but cannot work with asa.

  the asa is connected to the wan via zoom router (adsl)

  Are you telnet in the firewall?

  Follow these steps to display the debug output:

  monitor terminal

  farm forestry monitor 7 (type this config mode)

  Otherwise if its console, do "logging console 7'.

  can do

  Debug crypto ISAKMP

  Debug crypto ipsec

  and then generate a ping from one device to the back of the ASA having 192.168.200.0 address towards one of the VPN subnets... and then paste the result here

  Concerning

  Farrukh

• Problem on site to site and between router vpn client series 2,800

  Hello

  I need a little help.

  I have 2 office of connection with a site to site vpn

  Each site has a dry - k9 router 800 series.

  Each router has actually client ipsec vpn active and all users can connect by using the client vpn with no problems.

  I added the lines for the vpn site to another, but the tunnel is still down.

  Here the sh run and sh encryption session 2 routers:

  OFFICE A

  version 15.3
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  OFFICE-A-DG host name
  !
  boot-start-marker
  boot-end-marker
  !
  AQM-registry-fnf
  !
  !
  AAA new-model
  !
  !
  AAA authentication login default local
  AAA authentication login xauthlist local
  AAA authorization exec default local
  AAA authorization exec vty group xauthlocal
  AAA authorization exec defaultlocal group bdbusers
  AAA authorization groupauthor LAN
  !
  !
  !
  !
  !
  AAA - the id of the joint session
  !
  Crypto pki trustpoint TP-self-signed-220561722
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 220561722
  revocation checking no
  rsakeypair TP-self-signed-220561722
  !
  !
  TP-self-signed-220561722 crypto pki certificate chain
  certificate self-signed 01
    
  quit smoking
  !
  !
  !
  !

  !
  !
  dhcp WIRED IP pool
  Network 10.0.0.0 255.255.255.0
  router by default - 10.0.0.254
  Server DNS 10.0.0.100
  !
  !
  !
  8.8.8.8 IP name-server
  no ip cef
  No ipv6 cef
  !
  !
  !
  !
  !
  Authenticated MultiLink bundle-name Panel
  !
  !
  !
  !
  !
  !
  !

  !
  !
  !
  !
  !
  VDSL controller 0
  !
  property intellectual ssh rsa ssh key pair name
  property intellectual ssh version 2
  property intellectual ssh pubkey-string
   
  !
  !
  crypto ISAKMP policy 3
  BA 3des
  preshared authentication
  Group 2
  !
  crypto ISAKMP policy 20
  md5 hash
  preshared authentication
  OFFICE-B-IP address ISAKMP crypto key XXXXX
  !
  ISAKMP crypto client configuration group remoteusers
  key XXXX
  DNS 10.0.0.100
  WINS 10.0.0.100
  domain.ofc field
  pool ippool
  ACL 101
  !
  !
  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
  tunnel mode
  Crypto ipsec transform-set esp - esp-md5-hmac xauathtransform
  tunnel mode
  !
  !
  !
  Crypto-map dynamic dynmap 10
  Set transform-set RIGHT
  Crypto-map dynamic dynmap 20
  Set transform-set RIGHT
  !
  !
  map clientmap client to authenticate crypto list userathen
  card crypto clientmap isakmp authorization list groupauthor
  client configuration address map clientmap crypto answer
  10 ipsec-isakmp crypto map clientmap Dynamics dynmap
  20 ipsec-isakmp crypto map clientmap
  defined OFFICE-B-IP peer
  Set transform-set RIGHT
  match address 115
  !
  !
  !
  !
  !
  !
  !
  ATM0 interface
  no ip address
  No atm ilmi-keepalive
  PVC 8/35
  aal5mux encapsulation ppp Dialer
  Dialer pool-member 1
  !
  !
  interface Ethernet0
  no ip address
  Shutdown
  !
  interface FastEthernet0
  INTERNAL description
  switchport access vlan 10
  no ip address
  !
  interface FastEthernet1
  no ip address
  Shutdown
  !
  interface FastEthernet2
  switchport access vlan 10
  no ip address
  !
  interface FastEthernet3
  switchport access vlan 10
  no ip address
  !
  interface Vlan1
  no ip address
  Shutdown
  !
  interface Vlan10
  IP 10.0.0.254 255.255.255.0
  IP nat inside
  IP virtual-reassembly in
  !
  interface Dialer0
  the negotiated IP address
  NAT outside IP
  IP virtual-reassembly in
  encapsulation ppp
  Dialer pool 1
  Authentication callin PPP chap Protocol
  PPP pap sent-name of user password xxx xxx 0
  clientmap card crypto
  !
  router RIP
  version 2
  10.0.0.0 network
  network 192.168.1.0
  !
  IP local pool ippool 10.16.20.1 10.16.20.200
  IP forward-Protocol ND
  no ip address of the http server
  no ip http secure server
  !
  !
  the IP nat inside source 1 interface Dialer0 overload list
  overload of IP nat inside source list 101 interface Dialer0
  IP route 0.0.0.0 0.0.0.0 Dialer0
  !
  !
  access-list 22 allow 10.16.20.0
  access-list 22 permit 10.16.20.0 0.0.0.255
  Note access-list 101 * ACL SHEEP *.
  access-list 101 deny ip 10.0.0.0 0.0.0.255 10.16.20.0 0.0.0.255
  access-list 101 permit ip 10.0.0.0 0.0.0.255 any
  access-list 115 permit ip 10.0.0.0 0.0.0.255 192.168.1.0 0.0.0.255
  !
  !
  !
  control plan
  !
  !
  !
  MGCP behavior considered range tgcp only
  MGCP comedia-role behavior no
  disable the behavior MGCP comedia-check-media-src
  disable the behavior of MGCP comedia-sdp-force
  !
  profile MGCP default
  !
  !
  !
  !
  !
  Line con 0
  no activation of the modem
  line to 0
  line vty 0 4
  exec-timeout 0 0
  preferred transport ssh
  transport input telnet ssh
  !
  Scheduler allocate 20000 1000
  !
  end

  OFFICE B

  OFFICE-B-DG host name
  !
  boot-start-marker
  boot-end-marker
  !
  AQM-registry-fnf

  !
  AAA new-model
  !
  !
  AAA authentication login default local
  AAA authentication login xauthlist local
  AAA authorization exec default local
  AAA authorization exec vty group xauthlocal
  AAA authorization exec defaultlocal group bdbusers
  AAA authorization groupauthor LAN
  !
  !
  !
  !
  !
  AAA - the id of the joint session
  !
  Crypto pki trustpoint TP-self-signed-1514396900
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 1514396900
  revocation checking no
  rsakeypair TP-self-signed-1514396900
  !
  !
  TP-self-signed-1514396900 crypto pki certificate chain
  certificate self-signed 01
    
  quit smoking

  !
  !
  8.8.8.8 IP name-server
  no ip cef
  No ipv6 cef
  !
  !
  !
  !
  !
  Authenticated MultiLink bundle-name Panel
  !
  !
  !
  !
  !
  !
  !
  license udi pid C887VAM-K9 sn FCZ191362Q7
  !
  !

  !
  !
  !
  !
  VDSL controller 0
  !
  property intellectual ssh rsa SSH key pair name
  !
  !
  crypto ISAKMP policy 1
  md5 hash
  preshared authentication
  !
  crypto ISAKMP policy 3
  BA 3des
  preshared authentication
  Group 2
  !
  crypto ISAKMP policy 20
  md5 hash
  preshared authentication
  encryption XXXX isakmp key address IP-OFFICE-A

  !
  ISAKMP crypto client configuration group remoteusers
  key xxxx
  DNS 192.168.1.10
  WINS 192.168.1.10
  rete.loc field
  pool ippool
  ACL 101
  !
  !
  Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
  tunnel mode
  Crypto ipsec transform-set esp - esp-md5-hmac xauathtransform
  tunnel mode
  Crypto ipsec transform-set esp - esp-md5-hmac rtpset
  tunnel mode
  !
  !
  !
  Crypto-map dynamic dynmap 10
  Set transform-set RIGHT
  Crypto-map dynamic dynmap 20
  Set transform-set RIGHT
  !
  !
  map clientmap client to authenticate crypto list userathen
  card crypto clientmap isakmp authorization list groupauthor
  client configuration address map clientmap crypto answer
  10 ipsec-isakmp crypto map clientmap Dynamics dynmap
  20 ipsec-isakmp crypto map clientmap
  peer IP-OFFICE-A value
  Set transform-set RIGHT
  match address 115
  !
  !
  !
  !
  !
  !
  !
  interface Loopback1
  no ip address
  !
  ATM0 interface
  no ip address
  No atm ilmi-keepalive
  PVC 8/35
  aal5mux encapsulation ppp Dialer
  Dialer pool-member 1
  !
  !
  interface Ethernet0
  no ip address
  Shutdown
  !
  interface FastEthernet0
  switchport access vlan 30
  no ip address
  !
  interface FastEthernet1
  switchport access vlan 30
  no ip address
  !
  interface FastEthernet2
  switchport access vlan 20
  no ip address
  !
  interface FastEthernet3
  switchport access vlan 10
  no ip address
  !
  interface Vlan1
  no ip address
  Shutdown
  !
  Vlan30 interface
  IP 192.168.1.254 255.255.255.0
  IP nat inside
  IP virtual-reassembly in
  !
  interface Dialer0
  the negotiated IP address
  NAT outside IP
  IP virtual-reassembly in
  encapsulation ppp
  Dialer pool 1
  Authentication callin PPP chap Protocol
  PPP pap sent-name to user
  clientmap card crypto
  !
  router RIP
  version 2
  10.0.0.0 network
  network 192.168.1.0
  !
  IP local pool ippool 10.16.20.201 10.16.20.250
  IP forward-Protocol ND
  no ip address of the http server
  no ip http secure server
  !
  !
  the IP nat inside source 1 interface Dialer0 overload list
  overload of IP nat inside source list 101 interface Dialer0
  IP nat inside source static tcp 192.168.1.100 5060 interface Dialer0 5060
  IP nat inside source static tcp 192.168.1.100 5061 interface Dialer0 5061
  IP nat inside source static tcp 192.168.1.100 5062 interface Dialer0 5062
  IP nat inside source static tcp 192.168.1.100 5063 5063 Dialer0 interface
  IP nat inside source static tcp 192.168.1.100 5064 interface Dialer0 5064
  IP nat inside source static udp 192.168.1.100 5060 interface Dialer0 5060
  IP nat inside source static udp 192.168.1.100 5061 interface Dialer0 5061
  IP nat inside source static udp 192.168.1.100 5062 interface Dialer0 5062
  IP nat inside source static udp 192.168.1.100 5063 5063 Dialer0 interface
  IP nat inside source static udp 192.168.1.100 5064 interface Dialer0 5064
  IP nat inside source static tcp 192.168.1.100 3541 interface Dialer0 3541
  IP nat inside source static udp 192.168.1.100 3541 interface Dialer0 3541
  IP route 0.0.0.0 0.0.0.0 Dialer0
  !
  !
  sheep allowed 10 route map
  corresponds to the IP 150 101
  !
  access-list 22 allow 10.16.20.0
  access-list 22 permit 10.16.20.0 0.0.0.255
  access list 101 deny ip 192.168.1.0 0.0.0.255 10.16.20.0 0.0.0.255
  ACCESS-list 101 permit ip 192.168.1.0 0.0.0.255 any
  access-list 115 permit ip 192.168.1.0 0.0.0.255 10.0.0.0 0.0.0.255
  !
  !
  !
  control plan
  !
  !
  !
  MGCP behavior considered range tgcp only
  MGCP comedia-role behavior no
  disable the behavior MGCP comedia-check-media-src
  disable the behavior of MGCP comedia-sdp-force
  !
  profile MGCP default
  !
  !
  !
  !
  !
  Line con 0
  no activation of the modem
  line to 0
  line vty 0 4
  exec-timeout 0 0
  password Password02
  preferred transport ssh
  transport input telnet ssh
  !
  Scheduler allocate 20000 1000
  !
  end

  Thanks in advance for any help :)

  the site at the other tunnel is mounted, but it does not pass traffic; What is the source and destination ip on the router that you are trying to ping the address

  whenever you try to open the traffic from router A to router B, you must to the source of the traffic.

  for ex,.

  Router A-->10.1.1.1--fa0/0

  Router B - 172.168.1.100

  source of ping 172.168.1.100 router # 10.1.1.1

  After doing the pings, send the output of the show counterpart of its crypto ipsec at both ends

• ASA VPN server and vpn client router 871

  Hi all

  I have ASA 5510 as simple VPN server and 871 router as simple VPN client. I want to have the user ID and permanent password on 871 and not to re - enter username and password since 871 uses dynamic IP address and every time I have to ' cry ipsec client ezvpn xauth "and type user name and password.

  any suggestions would be much appreciated.

  Thank you

  Alex

  Do "crypto ipsec client ezvpn show ' on 871, does say:

  ...

  Save password: refused

  ...

  ezVPN server dictates the client if it can automatically connect with saved password.

  Set "enable password storage" under the group policy on the ASA.

  Kind regards

  Roman

• Static and NAT router to router VPN

  Hello

  I have two site VPN using routers. The VPN is fine, BUT - at the end of the seat, the customer has NAT entries static to allow incoming connections - any service that has a NAT static to allow incoming connections from the Internet is inaccessible in the same way. Ping, for example, doesn't have this problem because there is no static NAT entry. I tried to configure a route map-"No. - nat" according to the http://www.cisco.com/en/US/partner/tech/tk583/tk372/technologies_configuration_example09186a00800949ef.shtml , I thought I was working.

  H.O. has the IP 131.203.64.0/24 and 135.0.0.0/24 (I know, I know - I'm trying to change), and the R.O. 192.168.1.0/24.

  Bits of configuration:

  IP nat inside source overload map route SHEEP interface Ethernet0

  IP nat inside source static tcp 135.0.0.248 131.203.100.27 3389 3389 extensible

  (other static removed)

  Int-E0-In extended IP access list

  ip permit 192.168.1.0 0.0.0.255 any

  (other entries deleted)

  access-list 198 deny ip 131.203.64.0 0.0.0.255 192.168.1.0 0.0.0.255

  access-list 198 deny ip 135.0.0.0 0.0.0.255 192.168.1.0 0.0.0.255

  access-list 198 allow ip 135.0.0.0 0.0.0.255 any

  SHEEP allowed 10 route map

  corresponds to the IP 198

  1 remove the static entry for the specified host the VPN problem, but obviously breaks things :(

  2. as mentioned, the VPN itself works fine, I can ping hosts perfectly.

  Any help greatly appreciated :)

  Thank you

  Mike.

  You must use the option of the route to the static NAT map. This is a new feature in 12.2 (4) T according to this page:

  http://www.Cisco.com/univercd/CC/TD/doc/product/software/ios123/123cgcr/ipras_r/ip1_i2g.htm#1079180

  He must do exactly what you want. The old, another way to do is use "The thing", where you create a loopback interface and don't make a nat interface and use routing strategy for routing VPN traffic to one address on the same subnet as the loopback interface, but not the address of the loop. IOS then that réacheminera traffic to the real destination (in this case the remote VPN site), but since now it is not a 'ip nat inside' interface, the static nat translations does not apply and the VPN traffic will not be translated. The problem with this solution is that all loopback traffic is switched to the process, so it is a bit of a hack, but these things are sometimes necessary.

  HTH

• A Site VPN PIX501 and CISCO router

  Hello Experts,

  I have an at home test lab, I set up a site to site vpn using a router Cisco PIX501 and CISCO2691, for configurations, I have just a few links on the internet, because my background on VPN configuration is not too good, for the configuration of routers, I followed this link:

  www.Firewall.CX/Cisco-Technical-Knowledgebase/Cisco-Routers/867-Cisco-ro...

  and for configuring pIX I just use the VPN Wizard of pix. All confgurations but ping failed. Hope you can help me with this, don't know what to do here (troubleshooting).

  Joint here is the configuration of my router, topology, as well as the pix configuration. Hope you can help me with this. Thanks in advance.

  Hi Mark,

  I went in the Config of the ASA

  I see that the dispensation of Nat is stil missing there

  Please add the following

  access-list allowed sheep ip 192.168.1.0 255.255.255.0 172.21.1.0 255.255.255.0

  inside NAT) 0 access-list sheep

  Then try it should work

  Thank you

  REDA

• Router vpn site to site PIX and vpn client

  I have two on one interface on the pix vpn connections that terminate VPN. client vpn and VPN site-to-site have passed phase one and two and decrypt and encrypt the packets. However as in another post I can not ping through the l2l vpn. I checked this isn't a nat problem a nd two NAT 0 on the pix and the NAT on the router access lists work correctly.

  ISAKMP crypto RTR #show its
  IPv4 Crypto ISAKMP Security Association
  status of DST CBC State conn-id slot
  66.x.x.x 89.x.x.x QM_IDLE 2001 0 ACTIVE

  IPv6 Crypto ISAKMP Security Association

  local ident (addr, mask, prot, port): (192.168.2.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (192.168.10.0/255.255.255.0/0/0)
  current_peer 66.x.x.x port 500
  LICENCE, flags is {origin_is_acl},
  #pkts program: 23583, #pkts encrypt: 23583 #pkts digest: 23583
  #pkts decaps: 18236, #pkts decrypt: 18236, #pkts check: 18236
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 0, #pkts compr. has failed: 0
  #pkts not unpacked: 0, #pkts decompress failed: 0
  #send 40, #recv errors 0

  local crypto endpt. : 89.x.x.x, remote Start crypto. : 66.x.x.x
  Path mtu 1380, ip mtu 1380, ip mtu BID Dialer0
  current outbound SPI: 0xC4BAC5E (206285918)

  SAS of the esp on arrival:
  SPI: 0xD7848FB (225986811)
  transform: aes - esp esp-sha-hmac.
  running parameters = {Tunnel}
  Conn ID: 3, flow_id: Motorola SEC 1.0:3, card crypto: PIX_MAP
  calendar of his: service life remaining (k/s) key: (4573083/78319)
  Size IV: 16 bytes
  support for replay detection: Y
  Status: ACTIVE

  the arrival ah sas:

  SAS of the CFP on arrival:

  outgoing esp sas:
  SPI: 0xC4BAC5E (206285918)
  transform: aes - esp esp-sha-hmac.
  running parameters = {Tunnel}
  Conn ID: 4, flow_id: Motorola SEC 1.0:4, card crypto: PIX_MAP
  calendar of his: service life remaining (k/s) key: (4572001/78319)
  Size IV: 16 bytes
  support for replay detection: Y
  Status: ACTIVE

  outgoing ah sas:

  outgoing CFP sas:

  Expand the IP NAT access list
  10 deny ip 192.168.2.0 0.0.0.255 192.168.10.0 0.0.0.255 (21396 matches)
  20 permit ip 192.168.2.0 0.0.0.255 everything (362 matches)
  Expand the IP VPN_ACCESS access list
  10 permit ip 192.168.20.0 0.0.0.255 192.168.10.0 0.0.0.255 (39724 matches)

  I looked on the internet and that it points to a routing error when packets are being encrypted and decrypted, but you can't do a ping on the binding. However when I test the connection I did not enter any of the static routes that networks are connected directly on each side of the pix and the router. any help would be a preciated as I think there's maybe something is blocking the ping to reach the internal network at the end of pix with a configured access list.

  is ping failure of the only thing between the site to site VPN? and assuming that all other traffic works fine since it decrypts and encrypts the packets.

  If it's just ping, then activate pls what follows on the PIX:

  If it is version 6.3 and below: fixup protocol icmp

  If it is version 7.0 and higher: select "inspect icmp" under your political map of the world.

  Config complete hand and on the other could help determine if it's a configuration problem or another problem.

• Use Photoshop elements 2 and I can't seem to get, but a single layer, is displayed in the palette no matter how many photos that I place in the document.  What I am doing wrong?

  Use Photoshop Elements 2 and can't seem to get, but a single layer, is displayed in the palette no matter how many picutres I place in the document.  What I am doing wrong?

  Did some reading and found my problem. Sorry if I caused any problems.  Am just true layers again. Thank you all

• Strange double NAT, although there is only a single router

  My ISP (RCN) changed my modem at a speed greater than one.  Although a router built-in, I told them that I didn't use their router, only my Time Capsule, so they disabled.  However, my Time Capsule kept gives me an error message Double NAT and amber flashing against Green, even though everything seemed to work (wireless and wired) and said that I should switch DHCP and NAT to bridge mode.  Correction of the error, but I do not understand what caused the Double NAT if there is only a single router.  The ISP Technical Support people confirmed their control center is not the router feature on in the new modem, I ask.  They also said that their network supports DHCP, although they have other who use the Bridge Mode, although they do not support.   And they knew nothing about it, he said to ask Apple.  They also offered to switch back, but because this modem is faster at the same price.  (He called a bypass gateway 3-in-1).  Many people online told not to use his router, it's why I unplug it and only use the time Capsule.

  So if someone can give me feedback, I'd appreciate it. I must:

  1. keep running the new modem and my Time Capsule in Bridge Mode.

  2. run the new modem in DHCP mode, as they put in place and do not worry Time Capsule seeing amber / flashing Double NAT error.

  3 swap back to the previous modem, which was 50 Mbps against it with (theoretically) 155 Mbit/s (it's only works in 50-70).

  I'm not really all that, but I hope that one of you maybe.  Thank you!!!

  Although a router built-in, I told them that I didn't use their router, only my Time Capsule, so they disabled.

  ISPS often make the mistake of simply turn off the radio on a modem/router...which service does not disable the router function of the device. You still have a wired router when ISPS are making this mistake.

  However, my Time Capsule kept giving me an error message Double NAT

  This confirms again that the ISP has not disabled the function of the router to your modem/router.  On some modems/routers or gateways, it is not possible to get the device to act as a simple modem.

  The ISP Technical Support people confirmed their control center is not the router feature on in the new modem, I ask.

  The fact remains that you wouldn't see a Double NAT error unless the ISP system acted as a router... Despite what people of PSI say. You may need to get a 2nd or 3rd person-level support, who knows what they are doing.

  1. keep running the new modem and my Time Capsule in Bridge Mode.

  Yes, if you want to avoid the mistake of NAT Double... what you are doing. But, the time Capsule will not be your router.  The device of the ISP will be.

  2. run the new modem in DHCP mode, as they put in place and do not worry Time Capsule seeing amber / flashing Double NAT error.

  This only if you willing to accept the fact that the ISP did not correctly change your gateway to make it work as a simple modem only.  You might be able to get away with a Double NAT error on a simple network, but there is no reason more complicate things with a misconfiguration in unless whether there are a few reasons to do it and it can't be avoided.

  3 swap back to the previous modem, which was 50 Mbps against it with (theoretically) 155 Mbit/s (it's only works in 50-70).

  Your decision if you want to run a simple modem with time Capsule, or accept the fact that the time Capsule won't have your router when it is configured in Bridge Mode, or you see a Double NAT error on the network.

  If it were me, I would go back to what I know will work properly... the simple modem and time Capsule as the router.

• 5 routing VPN site

  Hi all

  I threw myself little in this project without a lot of lead in.  Basically, we have 5 sites

  Site A: HQ with ASA 5520

  Site B: Remote with 5505 with L2L at Site A

  Site C: Remote with 5505 with L2L at Site A

  Square D: distance with 5505 with L2L at the Site

  Site E: Remote with 5505 with L2L at Site A

  In an emergency, I had to get phone running systems when a T1 PTP line was cut at the beginning by the customer! I created a VLAN on each phone named 5505 and created the Tunnels of VPN L2L all return to the HQs 5520.  Everything was good in the neighborhood, phones were talking about main PBX server to HQ, we could compose and in no problem.  The problem is now the phone Vender tells us that we need routing between each site. We cannot compose between each remote site without using external number (whereas before you dial internal extensions in order to reach all other sites)

  Site B needs to talk to the PBX to C, D and E (A, obviously as well but that is already at work) and so on.

  I found topics dealing with 2 remote sites requiring a routing, however, with 4 that all need to routing to the other configs will very quickly very vast and complicated.  There is already extra virtual private networks to of the HQ 5520 who go elsewhere and a good amount of security configurations, so the config is already pretty decently sized.

  Is there a better way to do this, or should I start to write my setups now?

  If I understand your question, you need to configure a list of VPN networks on each VPN Ray and the hub.

  For example on the RADIUS B a crypto access list that is similar to:

  ip-> A B permit

  ip-> C B permit

  ip-> D B permit

  ip-E > B permit

  corresponding Cryptography ACL on the hub for talks would be like:

  IP-> B to allow

  IP C-> B permit

  allow the ip D-> B

  E-> B ip license

  Repeat for each Department accordingly.

  So basically your configuration crypto would ' t grow, only the ACL crypto.

  You can work with groups of objects to simplify the ACL crypt, in this case:

  Crypto ACL on Hub B:

  object-group VoIP-dst

  object A

  object C

  object D

  object E

  object-group VoIP-src

  object B

  permit ip src VoIP VoIP-dst

  And so on...

  Just make sure your config allows same-security-traffic intra-interface

• Cisco VPN Client and Windows XP VPN Client IPSec to ASA

  I configured ASA for IPSec VPN via Cisco VPN Client and XP VPN client communications. I can connect successfully with Cisco VPN Client, but I get an error when connecting with the XP client. Debugging said "misconfigured groups and transport/tunneling mode" I know, they use different methods of transport and tunneling, and I think that I have configured both. Take a look at the config.

  PS a funny thing - when I connect with client VPN in Windows Server 2003, I have no error. The only difference is that client XP is behind an ADSL router and client server is directly connected to the Internet on one of its public IP of interfaces. NAT in the case of XP can cause problems?

  Config is:

  !

  interface GigabitEthernet0/2.30

  Description remote access

  VLAN 30

  nameif remote access

  security-level 0

  IP 85.*. *. 1 255.255.255.0

  !

  access-list 110 scope ip allow a whole

  NAT list extended access permit tcp any host 10.254.17.10 eq ssh

  NAT list extended access permit tcp any host 10.254.17.26 eq ssh

  access-list extended ip allowed any one sheep

  access list nat-ganja extended permit tcp any host 10.254.17.18 eq ssh

  sheep-vpn access-list extended permits all ip 192.168.121.0 255.255.255.0

  tunnel of splitting allowed access list standard 192.168.121.0 255.255.255.0

  flow-export destination inside-Bct 192.168.1.27 9996

  IP local pool raccess 192.168.121.60 - 192.168.121.120 mask 255.255.255.0

  ARP timeout 14400

  global (outside-Baku) 1 interface

  global (outside-Ganja) interface 2

  NAT (inside-Bct) 0 access-list sheep-vpn

  NAT (inside-Bct) 1 access list nat

  NAT (inside-Bct) 2-nat-ganja access list

  Access-group rdp on interface outside-Ganja

  !

  Access remote 0.0.0.0 0.0.0.0 85.*. *. 1 2

  Route outside Baku 10.254.17.24 255.255.255.248 10.254.17.10 1

  Route outside Baku 192.1.1.0 255.255.255.0 10.254.17.10 1

  Outside-Baku route 192.168.39.0 255.255.255.0 10.254.17.10 1

  Route outside-Ganja 192.168.45.0 255.255.255.0 10.254.17.18 1

  Route outside-Ganja 192.168.69.0 255.255.255.0 10.254.17.18 1

  Route outside-Ganja 192.168.184.0 255.255.255.0 10.254.17.18 1

  Route outside Baku 192.168.208.16 255.255.255.240 10.254.17.10 1

  Route outside-Ganja 192.168.208.112 255.255.255.240 10.254.17.18 1

  dynamic-access-policy-registration DfltAccessPolicy

  Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT

  Crypto ipsec transform-set newset aes - esp esp-md5-hmac

  Crypto ipsec transform-set esp-3des esp-md5-hmac vpnclienttrans

  Crypto ipsec transform-set vpnclienttrans transport mode

  Crypto ipsec transform-set esp-3des esp-md5-hmac raccess

  life crypto ipsec security association seconds 214748364

  Crypto ipsec kilobytes of life security-association 214748364

  raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map

  vpnclientmap 30 card crypto ipsec-isakmp dynamic dyn1

  card crypto interface for remote access vpnclientmap

  crypto isakmp identity address

  ISAKMP crypto enable vpntest

  ISAKMP crypto enable outside-Baku

  ISAKMP crypto enable outside-Ganja

  crypto ISAKMP enable remote access

  ISAKMP crypto enable Interior-Bct

  crypto ISAKMP policy 30

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  No encryption isakmp nat-traversal

  No vpn-addr-assign aaa

  Telnet timeout 5

  SSH 192.168.1.0 255.255.255.192 outside Baku

  SSH 10.254.17.26 255.255.255.255 outside Baku

  SSH 10.254.17.18 255.255.255.255 outside Baku

  SSH 10.254.17.10 255.255.255.255 outside Baku

  SSH 10.254.17.26 255.255.255.255 outside-Ganja

  SSH 10.254.17.18 255.255.255.255 outside-Ganja

  SSH 10.254.17.10 255.255.255.255 outside-Ganja

  SSH 192.168.1.0 255.255.255.192 Interior-Bct

  internal vpn group policy

  attributes of vpn group policy

  value of DNS-server 192.168.1.3

  Protocol-tunnel-VPN IPSec l2tp ipsec

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value split tunnel

  BCT.AZ value by default-field

  attributes global-tunnel-group DefaultRAGroup

  raccess address pool

  Group-RADIUS authentication server

  Group Policy - by default-vpn

  IPSec-attributes tunnel-group DefaultRAGroup

  pre-shared-key *.

  Hello

  For the Cisco VPN client, you would need a tunnel-group name configured on the ASA with a pre-shared key.

  Please see configuration below:

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

  or

  http://tinyurl.com/5t67hd

  Please see the section of tunnel-group config of the SAA.

  There is a tunnel-group called "rtptacvpn" and a pre-shared key associated with it. This group name is used by the VPN Client Group name.

  So, you would need a specific tunnel-group name configured with a pre-shared key and use it on the Cisco VPN Client.

  Secondly, because you are behind a router ADSL, I'm sure that's configured for NAT. can you please activate NAT - T on your ASA.

  "crypto isakmp nat-traversal.

  Thirdly, change the transformation of the value

  raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map

  Let me know the result.

  Thank you

  Gilbert

• VPN client and contradictory static NAT entries

  Hello, we have a VPN IPSEC implemented on a router for remote access. It works very well, for the most part. We have also a few PAT static entries to allow access to a web server, etc. from the outside. We deny NATting from the range of IP addresses for the range of VPN client and it works except for entries that also have PAT configurations.

  So, for example, we have web server 10.0.0.1 and a PAT redirection port 10.0.0.1: 80 to the IP WAN port 80. If a VPN client tries to connect to 10.0.0.1: 80, the syn - ack packet back to the customer WAN IP VPN on the router! If the VPN client connects to the RDP server 10.0.0.2:3389, it works very well that this server is not a static entry PAT.

  Is there a way to get around this?

  Thank you!

  There is a way to get around, use the same settings you have for your dynamic nat in your nat staitc entries, something like this:

  Currently, it should show as:

  IP nat inside source static XXXXX XXXX 80 80

  you need to take it

  IP nat inside source static 80 XXXX XXXX 80 map route AAAA

  When your itinerary map YYY refers to something with an acl that you refuse traffic from inside your router for the pool of vpn

  IP Access-list ext nonat

  deny ip 10.0.0.0 0.0.0.255

  Licensing ip 10.0.0.0 0.0.0.255 any

  route allowed AAAA 10 map

  match ip address sheep

  You even need all the static PAT

  HTH

  Ivan

• 8.3 (1) ASA Cisco VPN Client and IP Communicator - one-way communication

  Community salvation.

  I have a strange problem with my setup and I'm sure it's either some type of routing (or NAT) or just missing one rule allows traffic. But I'm now at a point where I would like to ask your help.

  I have a few users remote access that have the Cisco IP Communicator (CICC) application installed on their laptops. So:

  The VPN with CPIC user <> ASA Firewall <> router voice <> MAC <> IP phone

  The VPN works fine for all other traffic. The connection of basis for the IP Communicator works well. He get is connected to the CallManager, is shown as registered and you can even call an internal phone and also external phones. BUT: while you can hear the called party (if the phone internal) it does not work for the other direction. There is no sound from the remote/appellant.

  I already understood that it is also not possible to ping from the phone VPN to the internal subnet IP phone. While the VPN user can ping any other device in the network internal, he cannot do for Cisco IP phones. But if the VPN phone calls a phone no-internal (mobile...) - it works!

  My thought is that the call cannot be build up properly between the VPN phone and the internal phone.

  I found similar situations with google, but they are all for the reverse: call for internal works, but not for VPN.

  What do you think?

  Hello

  Usually ASA lists specific to the customer networks VPN Split Tunnel runs.

  This would mean that there is a Split Tunnel ACL used in configurations of the SAA for this VPN connection that needs to have the missing network added to the VPN connection traffic.

  -Jouni