GI installation hangs at 65%, try operations remotely

Similar Questions

• OfficeJet J4550: Could not load the driver for the WIN10 - installation hangs

  Updated my Dell XPS to WIN10. I tried to upgrade the driver for my J4550 but installation hangs at the beginning of the installation process, "control systems".  When I tried the download, the old files from HP devices detected HP program and deleted. Now my computer does not even recognize the OfficeJet when you plug into the USB port.

  Need help why computer does not recognize the printer no matter what I do and how to get the computer to download the driver.

  Hello
  Follow the steps below and check if it solves the problem:

  1 open the Mcafee Virus and Spyware Protection software you are interested in, click on calendar and perform analyses. Click analysis in real time, and then click stop. Select until I restart the PC and confirm by clicking the button turn off.

  Now, try to reinstall the HP software and check if the installation goes as planned.

  If the problem persists, run the following tool:
  FTP://ftp.HP.com/pub/Printers/datfileremover/installdatfileclean.exe
  Then, run the Setup file and check all difference

  Kind regards
  Shlomi

• Robocopy hangs when you try to copy a file which in use

  Hello

  I find that Robocopy hangs when you try to copy the file using, for example an Outlook .pst file. The behavior of Vista was not to copy the file according to the retry and wait switches from command line, which allowed the backup race move to the next file and finally finish. With Windows 7 the Robocopy session is suspended and resumes ever, even if the file she is trying to copy is closed.

  Is this behavior under Robocopy in Windows 7? Is it possible to get Robocopy to move to the file according to when he's trying to copy a file that is in use?

  Thank you

  Jason.

  "There is no need of me a pause in my script"-Yes, I understand [and should have done before].

  I just tested a network for the first time operation.  It hangs forever as your done even after I closed Outlook & waited for the w: 30 I put.  {I also ran with closed Outlook the first time just to make sure that the network itself had no problems}

  I read that you have provided the link.  This suggests that there is no solution.

  - - - - - - -

  You seem to be doing a lot more & probably more structured than mine operation, this workaround might not be of any use to you.  The other open files issue concerns a simple hourly backup of my kernel files that includes pst files.

  1 I xcopy all the files in a folder internal InterimBackup first.  Can I use XCopy or RoboCopy to send InterimBackup to the real destination.

  2 If Outlook is open then it will copy on InterimBackup and, if the previous Outlook.pst is still in InterimBackup she gets deleted by the attempt of xcopy.  [conclusion - XCopy verifies the existence of the replacement of a file, deletes it and only then discovered that the source file is locked and cannot be copied.]

  So I precede this with

  0 I run [if exists] copy D:\InterimBackup\Outlook.pst to D:\InterimBackup\Outlook2.pst

  The result is that whole process always ends but it only includes the last Outlook.pst that was available.  So I always make a point of Outlook to quit at some point during the day so that he could take part in this backup.

  If you have also tried this as a two part operation, your xcopy / robocopy in the folder InterimBackup would always succeed but would include only Outlook.pst if you had first closed the application.  Subsequent operation of RoboCopy would always succeed with the same possible omission.

  The downside of this might not suit your overall goal.  You'd have to RoboCopy separately all your others folder trees but keep the Outlook.pst in a tree that has not been included.  You could do this either by restructuring of your data or using RoboCopy exclude switches for the file Outlook.pst file.

  You have to accept that you might not be sure about the last time that the Outlook file had been included unless you had deliberately run the RoboCopy closing.

  I have reviewed this improvement by using Task Scheduler to respond in the event of closing Outlook and use it to initiate the copy outlook.pst to InterimBackup, then by running the part of the main operation on RoboCopy to this folder.  But my needs are so simple that I've never felt it's the logs of the events that I would have to put in place.

  As I say, it may not meet your needs.

• BI installation hangs on step 5 - Administrator Details

  Hello
  
  I downloaded Oracle Business Intelligence, v. 11.1.1.3.0 and try to install it.
  
  But the installer hangs on the details page administrator - step 5, after checking the settings of all other systems are very good!
  
  I checked several times that I have enter valid administrator username and password.
  
  What could be the problem and how can I get in this step, please?

  LeonMatch,

  You will need to install the loopback adapter to fix this password error during the installation of 11 g. Its a sine qua non for OBIEE 11 g to call the IP of the host file. It is defined in this way, you can go through the documentation for it.

  Instructions to install rear loop:

  To manually install Microsoft Loopback card in Windows XP, follow these steps:
  1. click on start and then click Control Panel.
  2. If you are in Classic view, click on switch to the display of the categories under control panel in the left pane.
  3. double-click on printers and other devices, and then click Next.
  4. under See also, in the left pane, click Add Hardware, and then click Next.
  5. click on Yes, I have already connected the hardware, and then click Next.
  6. at the bottom of the list, click Add a new hardware device, and then click Next.
  7. click on install the hardware that I manually select from the list and then click Next.
  8. click on network adapters, and then click Next.
  9. in the manufacturer box, click Microsoft.
  10. in the network adapter box, click the Microsoft Loopback adapter, and then click Next.
  11. click on finish.

  After that, go to the network configuration and look for the back loop network adapter and configure it with a static IP address, such as (192.168.1.1) as follows:

  After the step above, if the box has lost the network connection to the rest of the real network. Then go back and re - configure the network adapter physical in the way it was (for example, DHCP). Because of the feedback loop, the LISTENER. ORA should be updated to reflect the new static IP address assigned above as part of the configuration of loop back.

  Kind regards
  -Laurence.

• Flash Builder 4: Installation hangs

  Hello

  just download Flash Builder 4 and try to install, but the installation hangs on display "install...". ». What are the causes of the problem?

  I use Windows XP SP3.

  Where did did you extract your Installer to? There is a known bug where a subcomponent hangs during installation on windows, when the path contains a space https://bugs.adobe.com/jira/browse/FB-26442leader.

  Jason San Jose

  Software engineer, Flash Builder

• my iphone hangs when I try to open the content of the email

  my iphone hangs when I try to open the content of the email

  What ios version do you have? It's 9.3? Because there is a bug in the most recent update, which can freeze your mail and Safari.

  Apple should have an update out before the end of week

  Fingers crossed

• Why the labwindows/cvi Installer runs whenever I try to start labview 7.1, after I installed N!-series?

  Why the labwindows/cvi Installer runs whenever I try to start labview 7.1, after I installed N!-series?  The installation program runs 3 times now and asks me to restart every time.  Then I reboot and it happens all over again when I try to start labview 7.1, unless I select Cancel 3 times in a row then labview starts.

  Thank you once again.  I am running.

  Barry-AIC

• My windows Explorer hangs in almost all operations

  See this thread if it helps:

  Windows Explorer crashes when delete or rename files
  http://www.Vistax64.com/Vista-General/32058-Windows-Explorer-hangs-when-deleting-renaming-files.html#post890328

  My windows Explorer hangs in almost all operations.    I don't know why, I have to reboot and reconnect.  I am using Windows XP Pro.  Thanks for you response
  Separated from the:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-files/Windows-Explorer-freezes-up-when-i-move-or-delete/c6d1a96f-006F-4906-9306-4bae5bca6f47

  Hi HBrown Gordon,

  In order to focus more on your particular situation, I shared your post to a new thread.

  Please take a look at the following information through Wunders in a previous post:

  The work of Windows Explorer is to consider what is in the disk and its directory and present this information to the user.  If the disk or the disk directories are corrupted, it confuses Windows Explorer and can lead to lock.  Whenever Windows Explorer crashes, the first step should be to achieve a check disk (chkdsk) with the /f or/r option.

  "How to perform disk error in Windows XP check"
    <>http://support.Microsoft.com/kb/315265 >

  Check disk can usually take hours depending on the speed and the size of the hard drive.  If corruption is present, it may take more time.  Plan on execution of the audit during the night or when you won't need your computer for awhile.  In addition, if corruption is present, files may be lost.  If possible, save what you can before you run the disk check.

  Hope that helps!

• XP SP3 installation hangs

  The installation hangs when the 'execution process after installation' I removed and tried it 4 times the same thing happens every time and SP3 is necessary to use TurboTax2011.  It is a single computer currently running XP Media Center Edition 2002.  Help, please!

  Hello

  ·         You get the error message?

  ·         Did you do changes on the computer before the show?

  Follow these methods.

  Method 1: Temporarily disable the security software.

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable the antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network at the time the anti-virus software is disabled, your computer is vulnerable to attacks.

  Method 2: Put the computer in a clean boot state to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  Method 3: You can also manually install updates (KB number) by downloading from the Microsoft Download Center.

  http://www.Microsoft.com/downloads/en/default.aspx

  Method 4: Follow the steps in the article.

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058

  For reference:

  Steps to take before you install Windows XP Service Pack 3

  http://support.Microsoft.com/kb/950717

• "Could access the Windows Installer Service" when you try to install codecs

  The Windows Installer

  When I try to run the codecs of corel, the following alert appears:

  The Windows Installer Service could not be accessed. This can happen if yor are running windows in safe mode, or if the installer of the window is not installed correctly. Contac your support staff, assistance.

  Can someone help me out here. I'm still trying to run a dvd on my WMP movie, but no codec plug-ins introduce yourself. Prior to that, I get another warning:

  Windows medal drive has not been closed properly. A damaged or incompatible plug-in could have caused the problem to occur.

  As a precaution, the plug-ins optional have been disabled.

  Hello

  I suggest you to follow the steps in this article and check if it helps:

  http://support.Microsoft.com/kb/315346

  It will be useful.

• I cannot remote in 2 Comp 1 Comp but when I try to remote in ordi1, there is not a mistake, it seems fair that it times out & nothing happens.

  XP Pro Performance Edition and Remote Desktop Connection

  I have 2 computers on the same network on the same router.  Ordi1 uses XP Pro Performance Edition SP3.  COMP2 uses Microsoft Windows XP Professional SP3.  I would like to implement if I do remote desktop connection in computers from another PC off the network.  COMP2 is set up fine, & I can remote inside.  Ordi1 has the same computer & the router settings, but will not let me.  The audit said harbour online tools the port is open.  When I try to remote in ordi1, there is not a mistake, it seems fair that it times out & nothing happens.  This problem is specific to the "Performance Edition" software?

  Hi Marc,

  Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please ask your question in the following forum.

  Windows XP IT Pro category

• Computer hangs when you try to watch live TV through windows media centre__

  Computer hangs when you try to watch live TV via windows media Center
   
   
   
  Signature of the problem:
  Problem event name: BlueScreen
  The system version: 6.0.6001.2.1.0.768.3
  Locale ID: 3081
  More information about the problem:
  BCCode: a
  BCP1: FFFFFA600C193FF8
  BCP2: 0000000000000002
  BCP3: 0000000000000001
  BCP4: FFFFF8000233499E
  OS version: 6_0_6001
  Service Pack: 1_0
  Product: 768_1
  Files helping to describe the problem:
  C:\Windows\Minidump\Mini112509-01.dmp
  C:\Users\user\AppData\Local\Temp\WER-132569-0.SysData.XML
  C:\Users\user\AppData\Local\Temp\WERCC53.tmp.version.txt
  Read our privacy statement:
  http://go.Microsoft.com/fwlink/?LinkId=50163&clcid=0x0409
  

  Hi Eddie Hunt

  Welcome to the Microsoft Answers Forum!

  I suggest you try this method and check if it is helpful

  Method 1:

  Start your computer in a clean boot and check what third-party software or program is at the origin of the problem. To help resolve the error and other messages, you can start Windows by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  How to run check and clean boot if you have the problem.

  i. Click Start, type msconfig in the search box and press ENTER.

  II. If you are prompted for an administrator password or a confirmation, type the password, or click on continue.

  III. in the general tab, click Selective startup.

  IV. under Selective startup, clear the check box load startup items.

  v. click on the Services tab, select the hide all Microsoft Services check box, and then click Disable all.

  VI. click OK.

  VII. When you are prompted, click on restart.

  VIII. after the computer starts, check if the problem is resolved.

  If the problem is solved, check what third-party software or program is at the origin of the problem, referring to the link given below:

  Clean boot

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  i. Click Start, type msconfig.exe in the start search box and press ENTER.

  II. If you are prompted for an administrator password or for confirmation, type your password, or click on continue.

  III. on the general tab, click the Normal startup option and then click OK.

  IV. When you are prompted to restart the computer, click on restart.

  Method 2:

  Install the latest codec package and check if that helps, link below will help you with the same:

  http://www.Microsoft.com/downloads/details.aspx?FamilyId=06fcaab7-DCC9-466B-b0c4-04db144bb601&displaylang=en

  Method 3:

  Update the graphics card. Steps to update the graphics card:

  i. click on start, type devmgmt.msc and then on enter.

  II. develop the graphics card and right click on the sub element and click on update driver.

  Link for reference: problems with watching TV on your computer

  Thank you, and in what concerns:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• I am trying to install some Elements 9 on a new computer. I downloaded the files, .7z, .exe and run the installer. When I try to open the items, I get an error message "please the product using Setup.exe in the root folder of installation/uninstallation.

  I am trying to install some Elements 9 on a new computer. I downloaded the files, .7z, .exe and run the installer. When I try to open the items, I get an error message "please the product using Setup.exe in the root folder of installation/uninstallation. I did it

  Hello

  Please see error: 'Please install Adobe installation using Setup.exe' when you install non-English versions of Adobe Creative Suite 3

  Hope that helps!

  Kind regards

  Sheena

• VMware 5.5.1 installation hangs at the end in XP Pro Sp3

  Then the installation hangs and won't be finished install but progress bar is just at the end have waited over an hour for her to finish - by using the administrator account.

  A folder for it but I don't see in the start menu.

  You know not so completely installed or missing components.  Nothing in Add/Remove programs related to it, so I think not completely installed.

  How to install XP or is there another version number which can do a physical examination to the conversion of the virtual machine of multiple partitions (drive by keeping letters) to a conversion of an existing for a guest of computer virtual of XP Sp3 XP run on Windows host 8.1 - hyper-v or vmware player prob / virtual box?

  Thank you very much.

  Also these: cmd prompt: netsh int ip reset resetlog.txt
  then netsh winsock reset catalog.
  Then reinstalled the NIC drivers as suggested.
  Also put the installer program office (extract the Installer file) and which ran on reboot.
  FIXED - after that restart could install all services installed in the end and shortened came office - running he opened the program.

• Standard of 6 CS installation hangs up on 'Close these applications.' Safari is closed. Now what?

  CS 6 Standard installation hangs at "close these applications: Notifications Safari.» Safari is closed, I do not see Active notifications. Someone knows what to do?

  Guest of installation of close SafariNotificati

  https://helpx.Adobe.com/Acrobat/KB/install-prompt-close-safarinotificati.html