Got unknown reason database

Similar Questions

• Firefox shows "the peer certificate has an invalid signature." ISMA shows "could not trust this certificate for unknown reasons.

  With the help of a PKI on site of 2 levels. Root CA offline (Standalone Windows 2008 R2, Enterprise Edition) and Isma online for delivery of certificates (Domain-Joined, issuing CA)

  ROOTCA certificate installed in the store and the approved display (PKCS #1 SHA-256 with RSA algorithm encryption and uses a signature SHA2)

  ISSUINGCA certificate installed in the store and display "couldn't trust for unknown reasons" has also SHA2 signature with the RSASSA-PSS algorithm

  Certificate issued is for a Web Server front end Lync and when it tries to load the secure web connection. I get the message "the peer certificate has an invalid signature."

  I completely uninstalled and reinstalled Firefox. Removed and added certificates ROOT and ISMA. Note: No problem when using the same certificates in Internet Explorer 8, 9 or 10 on the same system. Lync client also uses the same certificates, no problem. Only when access to the Web Services of Lync from Firefox.
  Question: Firefox NSS #11 internal Module PCKS supports RSASSA - PSS SHA-256 with different hashes? How can I solve this further?

  I finally found the problem. The ROOT CA has the following registry key configuration when cert Isma was published:

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\CertSvc\Configuration\IssuingCA\CSP\AlternateSignatureAlgorithm = 1

  This CA cause ROOT to issue the cert with a signature that is encrypted with the algorithm RSASSA-PSS (1.2.840.113549.1.1.10).

  This signature replacement algorithm no is apparently not supported for use with Firefox 27.0

  I changed the registry value on the ROOT CA to a value of 0. Renewed the cert IssuingCA (using the same private key) which is now on display with sha256RSA encryption. I have republished all my default web certificates now using this new broadcast chain CA without problem.

• My Firefox 15.0.1 cannot check all CA of SSL, it is said: "Cound not verify certificate for unknown reasons" when I find out the status of the certificate.

  Recently, I went to Windows 8 (from 7) and installed Firefox 15.0.1. Whenever I try to access a page secure HTTP I get a message that "this connection is untrusted. If I click on add exception and display the status of certificate I get the following message every time: "Cound not verify certificate for unknown reasons."

  I checked these sites in other browsers and they work fine. I also checked the certificates using this site: http://www.networking4all.com/en/support/tools/site+check/

  I tried to start firefox in compatibility mode of as and when that didn't help, I reinstalled it but nothing is changed. I use chrome for now but I hope that's not the only solution.

  What security (firewall, antivirus) software do you have?

  Some firewalls monitor secure connections (https) and send their own certificate instead of the certificate of the Web site.

  You can retrieve the certificate and check details such as WHO issued the certificates and the expiration dates of certificates.

  • Click on the link at the bottom of the error page: "I understand the risks".

  Let Firefox recover the certificate: "Add Exception"-> "get certificate".

  • Click on the "view..." button. "and inspect the certificate and the Coachman, who is the sender.

  You can see more details like the intermediate certificates that are used in the details pane.

• X 3500 HNAP call to the device failed for an unknown reason.

  During the installation process Cisco Connect X 3500 briefly to connect to internet (can surf the net very briefly in this window) but when he arrives at the end of the installation it saying unsuccessful then restarts.  Is there a way to manually connect just using the address IP is a browser?

  Error code: 82BD0305

  Error description: year HNAP call to the device failed for an unknown reason.

  Model name: loading...

  Model number: X 3500

  Serial number: unknown

  Firmware version: loading...

  Operating system: Windows 7 SP 1

  Software version: 1.4.12340.0

  Connection type (WAN): loading...

  (LAN) IP address: loading...

  (WAN) IP address: loading...

  The computer IP address: 192.168.1.103

  Found!  At the bottom of the Cisco Connect program window is a link to configure manually via a web browser.

• Error: "no restore points could be created for an unknown reason."

  original title: inoperable. Windows Vista system restore

  My system recovery, restore cannot create any requested restore point after that execution and by completing the order followed with pop - up box describing that no restore point could not be created for some unknown reason.  Help, please!

  Hello

  1. you are making a system image backup or you try to run the system recovery options system restore?

  2 are you try to create a restore point manually?

  3. at what stage you receive the error message?

• Connection failed for an unknown reason (IOM Java Client)

  Hello

  
  

  I have some code Client Java IOM that works if I have access to IOM without SSL.

  
  

  The problem occurs when I try another (production) server that uses the SSL protocol

  
  

  I use these libraries

  
  

  common - logging.jar

  cryptoj.jar

  EclipseLink.jar

  JRF - api .jar

  oimclient.jar

  Spring.jar

  WebServiceClient + SSL.jar

  wlfullclient.jar

  I also tried to add the system properties to add SSL debug, to ignore invalid host names, etc..

  I also created a file of keys, certificates imported and added

  		System.setProperty ("javax.net.ssl.trustStore", KEYSTORE);
  		System.setProperty ("javax.net.ssl.trustStorePassword", KEYSTORE_PASSWORD);

  		opening of session
  		System.setProperty ("java.security.auth.login.config", AUTHWL_CONF_PATH);
  		System.setProperty ("APPSERVER_TYPE", "wls");
  		String ctxFactory = "weblogic.jndi.WLInitialContextFactory";
  		< String, String > Hashtable env = new Hashtable < String, String > ();
  		env.put (OIMClient.JAVA_NAMING_FACTORY_INITIAL, ctxFactory);
  		env.put (OIMClient.JAVA_NAMING_PROVIDER_URL, OIM_JAVA_API_URL);
  		OIMClient client = new OIMClient (env);
  		customer. Login (OIM_ADMIN, OIM_ADMIN_PASSWORD.toCharArray ());

  URL of the IOM is referenced by intellectual property

  The error message is not really help a lot. The green text was added by me.

  User name and password have been double-checked, they work for the web INTERFACE.

  
  

  javax.security.auth.login.LoginException : weblogic.socket.UnrecoverableConnectException : [connection failed for an unknown reason: < bytes garbage here >]

  to weblogic.security.auth.login.UsernamePasswordLoginModule.login (UsernamePasswordLoginModule.java:194)

  at sun.reflect.NativeMethodAccessorImpl.invoke0 (Method Native( )

  at sun.reflect.NativeMethodAccessorImpl.invoke (NativeMethodAccessorImpl.java:57)

  at sun.reflect.DelegatingMethodAccessorImpl.invoke (DelegatingMethodAccessorImpl.java:43)

  at java.lang.reflect.Method.invoke (Method.java:606)

  to javax.security.auth.login.LoginContext.invoke (LoginContext.java:762)

  to javax.security.auth.login.LoginContext.access$ 000 (LoginContext.java:203)

  to javax.security.auth.login.LoginContext$ 4.run (LoginContext.java:690)

  to javax.security.auth.login.LoginContext$ 4.run (LoginContext.java:688)

  at java.security.AccessController.doPrivileged (Method Native( )

  to javax.security.auth.login.LoginContext.invokePriv (LoginContext.java:687)

  to javax.security.auth.login.LoginContext.login (LoginContext.java:595)

  to Thor.API.Security.LoginHandler.weblogicLoginHandler.login (weblogicLoginHandler.java:61)

  to oracle.iam.platform.OIMClient.login (OIMClient.java:212)

  to oracle.iam.platform.OIMClient.login (OIMClient.java:196)

  You cannot refer to the URL of the IOM by IP and use SSL. The host name must match the name on the certificate that will never happen if it is an IP address.

• Unknown OEM database backup

  In our system, a database was setup in the OEM backup to 23:00 every day. The backup has been normal.

  But since March 20, there is no backup information. In the

  Of backup reports, there is no information after the registration of the operation of backup on 19 March. So I don't altogether to no idea if it failed or successful.

  The backup includes the archivelog and remove it after backup the archivelog and a remaining after March 19, it seems that the backup failed.

  Is there a method I can find logs details about it?

  The problem is resolved. The reason is OEM issue. The solution is to restart OEM service.

• receiving exception "resource requested by this task has already been used by another task' for unknown reason

  Hi people.

  I am running in a bazaar error I'm not around.  I have a series of cDAQ chassis (9188) with a number of NOR 9208 each.  Everything I'm doing is the simplest of the simple acquisition of VI to extract data from each of the 16 channels of each 9208 and push values for the configuration UI.

  NOTE: the material is SIMULATED in MAX.

  I'm trying to create a task for each 9208, but DAQmx start Task.vi bombs out after the code creates the first few tasks successfully.  The exception:

  "Error occurred 200022 DAQmx = begin Task.vi; "Possible reasons: resource requested by this task has already been reserved by another task."

  Please see the attached screenshot.  I have provided two tables of physical constants Channel. Bombs currently wired table on 'AI_Module_07 '.  The unwired table bombs on the last "AI_Module_08".  It seems that I can move these constants in the table, so there is little or no motive behind the order.

  There are also segments of screenshot of MAX and the exception in the block diagram.

  Thanks to a bouquet.

  -Chris

  Hello Chris,

  Based on the screenshot you provided, it looks like you use too many independent tasks in a single chassis - I think that the timing engine can handle three (four memory), but based on this knowledge basethree simultaneous HAVE tasks - you can certainly use all eight locations to HAVE, but they will need to be divided into synchronized subsets.

  That said, if it is in fact the problem is that I feel, a more specific error would appropriate the "resource" referred in the present case is ostensibly the timing engine, but further clarification would be useful.

  Best regards

• Is what I got - a real database?

  Hello!
  
  Huge apologies for a stupid question, but I need an opinion of knowledgeable people.
  
  One of our "partners" provided us with supposedly a database. I've never dealt with Oracle and have no idea if it's a real database.
  
  Is there a special extension of the files containing the data? The files contains a bunch of .dll, .ser files .jar and some others. I suspect (in fact, I'm 99% sure) is not a database at all, but rather a bunch of garbage. What do you think?
  
  Thank you

  .dll, .ser, average .jar of files that it is an Installation - what we call 'Software RDBMS' are sometimes what many people call "Database".

  Normally install you the software and then, using the software installed, create the database.

  Database files should normally have. DBF extension but there is no hard and fast rule. The ADMINISTRATOR can create a database with files with no extension, no matter what extension, any combination of extensions!

  (Windows File Explorer certainly cannot identify database files!).

• I lost all my documents when I tried to erase my trash.  For some unknown reason, this for me.  I need help

  I have a Mac Air with the X 10 of IOS.  I was cleaning my files and create new files.  When I finished I wanted to clear my trash and to my sorprise all my documents have been lost.  I haver tried using restore but not able to do.  I have iphone 6s and a Mac computer.  Please help me.

  The correct action to take about lost documents would be to restore from a backup that is equivalent or time Machine.

  I was cleaning up my files...

  Please explain what you did and what you used to do.

• Simulator of fails silently load App for unknown reason

  Hi, I am a new Blackberry development.

  I spent some time writing some of my own MVC stuff and recently set up what should be the first alpha version of an application to use it. My big problem is that the Simulator is not load my application and I can't seem to find any information explaining why.

  I tried to run my application directly through the JDE plug-in in eclipse (run as and debug as with the Simulator) and I've tried it in several simulators. I put breakpoints in the main method to trap any successful attempt to even start the application and no breaking point are affected.

  I also tried to load the .cod file set up by eclipse in several simulators does not. I checked in the Simulator for all logs directory that may have hidden exception notice but so far I can't find anything in any newspaper that has anything other than details of startup modules, loads of Simulator (and other startup tasks.)

  When I try to load the app (in one of the above ways) all that happens is that an hourglass appears on the main screen to show his attempt to load the application, and then disappears without any other indication that something had happened.

  Anyone know where I should be looking to find the problem here? I'd appreciate any help that anyone can give, thanks to a ton. -Chris

  Expand the main screen using the menu key ("berry") ("Insert" of the keyboard for the simulators), scroll to the "Downloads" folder by using the arrows and click on it (NumPad 5 with Num Lock off, left click on the trackball/touchpad, left-click on the icon for the simulators of the touchscreen) and find your application here.

• My external drive stopped working for unknown reasons,

  It reads in RAW format, I tried to reformat, but it says "unable to complete format" ive downloaded programs to force reformat it without success, tried to repartition it. Help? advice? something ill try anything to save my hard drive portable 500 GB wd, ive downloaded test disk and accidentally changed the cylinders and don't remember what the correct setting has been, I assumed because the fix has not worked would not save my error.

  Hello

  1. have you tried to connect the hard drive on another computer?
  2. other USB devices work well?
  3. the USB external hard drive works in Mode safe?
  4. can you see the external hard drive USB in Device Manager?
  
  You may have performed the steps in the following article.
  Check a drive for errors
  http://Windows.Microsoft.com/en-us/Windows7/check-a-drive-for-errors
  Important: when running chkdsk on the drive hard if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost.
   
  It will be useful.

• Photoshop CS4: Images of the workspace are dyed blue for unknown reason

  Hello world.
  The question in that I'm running does not appear very often so I thought I would go and ask away. I use Photoshop CS4 (64 bit) and when I open an image in Camera Raw, I see perfect photos as they are. By bringing the file in the workspace, however, they are immediately covered in a blue tint which makes editing VERY boring photos. I used Photoshop on this laptop for a few years and never encountered a problem like this. My screen has been calibrated using the calibration tests integrated into Windows 7. Recently, I had to reinstall my programs Adobe After buying a new internal hard drive. This means that I had a clean slate before installing Photoshop. I had to reinstall Windows itself and when buying, my laptop came with some pre-installed Dell software.

  If only there was a Dell program that handled my colors? Photoshop seems to be the only one affected program, and it is ONLY in the workspace in particular, it has so well there have a problem program. I am a student in a photography class, so any advice would be helpful! Thank you!

  

  Yes, it's a question of color management. Most likely your pre-installed software used a setting or a specific color profile. Check your evidence and your system color management settings.

  Mylenium

• A virtual machine enters mode standby for unknown reason?

  We run vCenter Server 4.1.

  We find that we are not able to ping to a virtual machine (Windows 2003 Standard Edition) this morning.

  When check us in the console Client vCenter, we look at it says "happens in sleep mode.  When we try to open a session (I guess that bring us mode Standby - is correct?), we get a message "a ticket type mks has acquired" in the event of vCenter Server log.  We would like to know what this message means.

  Also, we check the possibility to and it is 'Always On', but hibernation is enabled.  However, it should still not go in standby mode.

  Your opinion is requested.

  Thank you

  Post edited by: TonyJK

  Someone must have connected, and Eve instead of disconnected.

  Or is your screen saver to sleep after some time... It should be OS leads, because VM ware does nothing to the active state of the operating system.

• Wrong colors listed for unknown reason

  Hello

  I use CS4. I am wanting to use a color. The color is available "in theory", but the right color is used when I select it.

  I use overlay to color a grayscale image that I've created. This process has worked in the past.

  The color I want to use is #0035f9. The color that appears is #3d57a7.

  The right color is in the foreground area. I tried to use color on the Umag, but the second color appeared.

  I then created a new layer and used the fill with the foreground color option - once again the second color appeared.

  I thought try and import the image precoloured and the color has changed to the second color once inside the document.

  Any ideas why it does not work?

  I have not had this problem before.

  You have probably changed your settings for color management in the world using a different monitor profile and not properly use it to proof overview or you have assigned a color profile of the specific document. Of course also check if you don't accidentally changed the RGB to CMYK color mode or none of it. Otherwise, we will need more info on the above points and your system more, possibly, screenshots to see what is happening.

  Mylenium