Group management

Similar Questions

• Can't see the new table in the PS Group Manager

  Sorry guys, I'm kinda new to storage management. I worked in existing bays built by the last person who was here. Now that he is gone, I was charged with the addition of two additional paintings/members to our existing EqualLogics. Problem is that I see the 2 members in Group Manager, but not the 2 new ones. We have a data center managed by 3rd party and they say that they have wired everything in. Both are supposed to be cross-connected series via a connection to one of our servers and the other in an existing table. Now physically I don't know how everything is connected. I console just in Workgroup Manager. I don't see new members there. I tried to connect from one of the servers connected using PuTTY and the connection series. I've used sides of Baud has offered online. But I can't connect what either. Sorry if this sounds very basic - but what don't get me? How to see these devices to even configure the network adapters and RAID?

  Thanks for any help guys

  Hmm... what exactly do you mean with "the table is connected to the active controller?

  Guys in your data center can make the photo of the back of the EQL? See the two CMs with the cables and the LEDS may help.

  When putty.exe close the window immediately that there is probably nothing on the other end, but when it remains open, it is normally a good sign. Press 'enter' or ctrl + c. If you see garbage or nothing the connection parameters doesn't match. Once again its 9600/8/1/n.

  Note: if ever you restart an active EQL the CM moves which makes it difficult when with only a working serial cable.

  You can also try is turning off the device. Verify that your connection to the CM right and turn on again. You will see output of a CM of start-up.

  Do not use is not a black font on a black background in putty also makes life easier ;)

  Kind regards

  Joerg

• Nexus 7 K of the group management interface

  Dear,

  with regard to the release of the group management interface, if I configured a vlan intervace to be as an interface of management for a (the default vdc) vdc

  When I connected to this vdc via telnet, can I switch to any other vdc?  (Suppose I have the role of the Admin that allows me to enter and config all the VCC)

  If possible, so that I don't have to do a management dedicated to each VDC ip

  I do that only if I want to give an account of the vdc admin to allow some users access to the VLAN specific only, is it true?

  Hello

  Yes, it is possible.  When you log on as an administrator and you want to join another vdc, you simply use this command:

  SwitchTo vdc

  This will lead to the vdc.  If you want to return to the admin vdc, just type "switchback."

  HTH

• VMware DRS Group Manager

  I see a group of DRS Manager now in Cluster settings. I don't know I'm well understand what it is and I find it difficult to locate documentation. Can you tell me some or explain it please?

  DRS group manager is used for affinity VM host. You can create the VM group and the value of rule to place these VMs on some hosts.

  ---

  MCITP: SA + WILL, VMware vExpert, VCP 3/4

  http://blog.vadmin.ru

• OID 11.1.1.6 - belonging to the user group management

  Dear,

  Is there a way of OIDS to manage the users, via a specific user attribute group membership?

  You all know that in AD for example, it is an attribute of the user "memberof" that could be used for this purpose I tried looking in OID for a similar attribute and actually found this a "orclMemberOf", however I can't figure out exactly how to use it. I tried editing through DOHAD, but got an error "constraint violation". I also tried to use ldapsearch as mentioned in this post Oracle Fusion Middleware security: group membership Fast searches within the OID with the attribute of orclMemberOf, but the attribute is not returned in the search results.

  Any ideas... ? We just want to know if the only way to manage the belonging to a group is done using the attribute 'uniquemember' of the group, or if it can be configured on the user object.

  Thank you

  White

  That can only means that is not your attribute to multiple values of the group.

  The default value for the OID, groups have an objectclass of groupOfUniqueNames and their membership multi value attribute is uniqueuniquemember.

  So lets say, you want to know the groups the admin account is a member, your application would be as follows:

  (uniqueMember = cn = orcladmin, cn = Users, dc is sampledomain, dc = com)

  This would release all memberships that belongs to the user.

  -Kevin

• Windows Vista - Mail - group management

  When I delete a contact that is in a group, the group will no longer appear in the To: a new message when I right click on the group name and select Action > Send Mail. The only solution I've found is: delete the Group and recreate the entire group, one contact at a time. It is a very painful process. My 4 groups contains +/-50 contacts and that, since all contacts are members of our association of Senior golfers, destruction produce often - dead, move to Florida, could not Arthroplasty of the knee, Alzheimer's, etc. What can I do to eliminate it this problem?

  Hello

  Thanks for the reply.

  Rather than delete the contact from the group to remove the contact from here:

  1. Open Windows Contacts by clicking on the button start , clicking all programs, and then clicking Windows Contacts.

  2. Right-click the contact you want to delete and then click on remove.

  See this link for more information:

  http://Windows.Microsoft.com/en-us/Windows-Vista/add-or-delete-contacts

  It will be useful.

• Drs host group management and the vm

  Hey guys I was reading the website Arnims how to create drs with the command groups can be new-drsgroup which looked really nice that you can do.

  But in powercli 5 allowing the command is no longer there.

  If anyone knows what happened with her or the replacement. Because im a large deployment and we must automate host placed in the correct when host groups that they placed in the correct cluster.

  The link to the Arnims post is http://www.van-lieshout.com/2011/06/drs-rules/

  Best regards, Boris

  New-DrsVmGroup is a function that is planned Arnim hist post in Listing 1.

  An ay to present them to your scripts is to save the code of Arnim in a .ps1, then point source this .ps1 file

  . ./New-DrsVmGroup.ps

  Note the space between the 2 points.

  You will now be able to call a cmdlet New-DrsVmGroup.

  Similar to the new DrsHostGroup (list 2) and new-DRSVMToHostRule (listing 3).

  You can also put all 3 functions in 1 .ps1 file and point source this file.

  Update: I can find no mention of a New-DrsGroup cmdlet in Arnim station

• TabGroups manager: new tabs from the previous group

  In older versions of Firefox I could open a new group with TGM and drag a new tab in that she has a new group with just this one new tab. Now (37 FF) a new group contains and controls all the tabs from the previous. No intependend the tabs in the new group management is possible.
  How can I create a new group of vacuum?

  You ask about an add-on. It is maybe the Addon or is more actively developed and supported.

  If I identified correctly this is the one

  • https://addons.Mozilla.org/firefox/addon/TabGroups-Manager/

  But it seems to have been updated in 2011
  I'm getting server not found for support and homesite.

  I suggest that you learn about the Mozilla Addons site for advice if this is still active or suggested alternatives.

  • https://forums.Mozilla.org/
    • I met this but it also seems obsolete https://code.google.com/p/tabgroupsmanager/

  Or just get your car among the hundreds of available alternatives here

  • https://addons.Mozilla.org/Firefox/extensions/tabs/

• Replacement for the Working Group to el Capitan Manager?

  I recently built new servers, intending using open directory.

  The equipment I use are the new mac mini servers, with two 1 TB drives and 16 GB of memory.

  Historically I have used Workgroup Manager for direct starting, deployment of the printer files, user groups and others.

  Is there a replacement for the Working Group Manager who no longer works with el capitan (10.11.3)?

  The replacement is the Manager of service profile. See the built-in help of server for instructions begin. This is beta-quality software, at best.

• Group missing user profile manager

  Server 4.0 on OSX 10.11.1 using.

  I have installation manager profile and work for our students by having the mac server running as the OD server with the profile as well as related to the AD Manager to allow users.  In the Profile Manager, I have a group called student that contains all the users of the student.  He works well with the Manager to set up profile settings to customize the user experience however I noticed today that 1 student shows is no longer as in the Group of students in the Profile Manager.  In two RFAS and editor of search on the mac Server directory the user shows as a member of the student group.

  I can't understand why this appears a user is no longer in the Group Manager profile when everything clearly shows them as a member.

  Problem has to do with LDAP on our Active Directory settings.  The MaxPageSize was too weak, as mentioned in Mac OS x: first 1000 results when querying Active Directory - Apple Support

• is Tsinternet user group, download manager, and NNTP service does not participate in 2008 if server windows Yes... Please give me the link of reference

  Required link that support it, upload, Tsinternet user group manager and the NNTP service is not longer involved in windows server 2008

  Hi HP_990,

  I would suggest to repost your question in our forums Windows Server TechNet here:

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer

  Thank you!

• EqualLogic group member network configuration error: "management interface should not be on the san subnet.

  Hello

  We currently have new EqualLogic 6100 device with this network configuration:

  Director of the IP - 192.168.0.2 (VLAN1).

  Member network config:
  eth0 - 192.168.0.3 (VLAN1)
  eth1 - 10.10.10.3 (VLAN2)
  eth2 - 10.10.10.4 (VLAN2)
  eth3 - 10.10.10.5 (VLAN2)
  ETH4 - empty

  I would attribute 192.168.0.4 to eth4, but received the error: "management interface should not be on the san subnet.

  I am sure that all interfaces eth has access to the VLAN1 and VLAN2, mean error indicates that eth4 should not access VLAN2 and only access the VLAN1 on the switch?

  Or eth0 should also have access to the VLAN2 only to reconfigure eth0 and eth4?

  Thank you

  > The group eating IP should be in iscsi VLANS?

  Yes!

  Note: If configure you an EQL it will ask an iSCSI port because nothing is more necessary to bring it up. The doest previous EQLs have a dedicated Mgmt Port and later, you can convert the last ethX as a MGMT port. This is the reason why configure you ISCSI at the beginning. (Think of a mixed group of newer and older models, and you get a picture)

  OK... once again it is the one and only member of the Group and there is making the production host connected to the right?

  The change of IP address, to a 3rd. subnet for temporary use.

  -Do not touch eth0-3 and the IP address of the group now

  -Configure the MGMT port and IP address management in the tempr group. Subnet. Use the Config-> Adv. Group-> network MGMT. You can change the MGMT Port of the Member, and the address IP of MGMT

  -For the registration of the configuration, you will lose access. You must place your admin PC in the templ. subnet so

  -Connect to the GroupMgr with temp again. INTELLECTUAL PROPERTY

  -Now you can change the IP address of group 10.10.10..x

  -Now you can change eth0 10.10.10.2

  -At the end, you can change the address IP of the Group MANAGEMENT, as well as the MGMT Port to 192.168.0.x

  -Change the IP address of your admin PC rear

  A failover, you should consider to hang a serial cable the active controller of the EQL. Use 9600,8,1, N with your favorite terminal program (putty.exe on windows). All the steps, you can perform from the command line.

  If this group and the only member not in production, but you can reset the config and restart from the beginning.

  Kind regards

  Joerg

• Don't Win 7 Home Premium no local users and groups under computer management

  I am trying to create local groups, but when I go into computer Managemmt as an admin there no option groups in the tree.  Aide said it is in "computer Management\System Tools\Local and Groups\Groups users", but the only options I have under system tools are planner of the event viewer, shared folders, Performance and device - not local users and groups management tasks.  No idea how I can get access to this?

  I think that it is only available if you have Windows 7 Professional or ultimate edition. Bob Larson Access MVP

• Security roles and workflow management groups

  People,

  There is a section on Workflow management groups and security roles in vCloud Request Manager Installation and Configuration Guide - Guide of Directors Chapter 5 and 6. I have difficulty working on the relationship between the two settings.

  My first question is around the goal of the WM default checkbox that the specific guide is used to set the default user workflow management group.

  What would a never used default WM? I mean, what would he ever substitute the other workflow management groups that you define.

  In addition, in the guide, it say cloud Blueprint Admin and Asset Manager security role is a combination of the Admin of Blueprint of cloud and the Asset Manager. Is cloud Blueprint Admin & Asset Manager being the two groups of workflow management, reasonable to assume that a security role is composed of workflow management groups?

  And when I select agent, I do not see a cloud Blueprint Admin and Asset Manager security role listed?

  Finally, is there a way to determine the exact permissions that contains a workflow management group/security role?

  Thank you

  Cormac

  The Group Management (WM) default workflow is largely an artifact of vSM based vRM.

  VSM, a group of WM is a collection of agents used to apply security and route of tasks, among other responsibilities. (For the purpose of vRM, an agent can defined as users who have access to the vRM admin interface).

  vRM mainly use WM groups as a way to deliver relevant communications to users based on their responsibilities for example vCD Admins, Asset Managers etc. vRM does not require other functions related to WM groups.

  For functional reasons, vSM requires that each officer with access to the capabilities of WM belong at least a WM group. In addition, at least one of these groups must be designated the default WM for this officer group. These functional reasons are not immediately relevant to the specific use of vRM rest however case the constraint. Suffice to say for vRM, every WM user must have a WM group by default even if this information must never be used.

  Roles and groups are separate entities. A role defines a set of privileges to access a particular functional area of the admin interface for example a role WM sets permissions to interact with the workflow. of the roles of management (CM) configuration sets permissions to review and modify records in the repository of vRM.

  A special role of WM can be associated with one or more groups WM. When this WM role is assigned to a user, that user inherits groups associated with this role, WM allowing to simplify the administration of groups. An individual user can also have other WM assigned groups to them directly, complementary to those inherited from their role of WM.

  At an abstract level, vRM defines three types of users of the admin interface:

  1 vCD Admins

  2. plan Admins

  3. managers

  However, the security of MSM model requires that each individual user must be implemented with several components. By default, vRM sets a "Asset Managers" WM Group of what assets all managers must belong. However, WM groups cannot be used to give access to the features as well, so a separate from the "Asset Managers" WM role is obliged to grant access to these features asset managers. By default, the role of "Asset Manager" WM is associated with the "Asset Managers" group such that any user who is assigned the role automatically belongs to the Group also. There is also a separate 'Asset Managers' CM role that gives asset managers they need to the repository vRM for example the possibility to add new licenses for software products.

  This model of definitions is repeated for 3 personas above with a group and several roles defined for each. When an administrator assigns a user to one of these characters they should assign the groups and roles appropriate according to the documentation. They should not need to be concerned by the distinctions between each component.

  The role of the "Plan Director Admin and Asset Manager" reflects that a user may need to be asset manager and a Director of Blueprint. Because a user can have a role to the maximum by functional area, vRM provides a compound that provides two sets of permissions. However, a user can belong to several groups WM, so it is never necessary to provide a composite group.

  The role of composite is there; just maybe not where you expect to find. Blueprint Admins do not need to access WM, so there is not a 'Blueprint' Admin or a composite WM role. Blueprint Admins do need access to configuration management so it's an "Admin blueprint" and a role of CM composite.

  The details of the user screen provides:

  • a summary of all groups to which a user belongs

  • provides a 'Détails' button to drill down on each role assigned to the user to inspect the permissions granted by this particular role

  You must be a vCD Admin to see areas of the screen.

• tabs and groups of tabs are lost

  Closing Firefox and then restarting him, invariably all my tab groups seem to have lost their legs. Reopening of groups of Eve extended or closed (using the Group Manager add-on tab) will not help.

  It is not happened on my previous install but have since upgraded to Kubuntu 14.04 and Firefox 29 (to be precise Firefox to canonical 1.0), I keep losing my tabs and groups of tabs.

  Don't know what mistake I make.

  In case you use "clear history of Firefox closing:

  • do not erase browsing history
  • Edit > Preferences > privacy > Firefox will be: "Use the custom settings for history": [X] 'Clear history of Firefox closing' > settings
  • https://support.Mozilla.org/KB/remove-browsing-search-and-download-history

  Note that compensation "Preferences of Site" clears all exceptions for cookies, images, pop-up windows, installation of software, passwords, and other specific data from Web site.

  You can check for problems with the sessionstore.js and sessionstore.bak files in the profile folder of Firefox that store session data.

  Rename (or delete) the sessionstore.js file and possible sessionstore-# .js files with a number and sessionstore.bak in the Firefox profile folder.

  • Help > troubleshooting information > profile directory: see file (Linux: open the directory;) Mac: View in the Finder)
  • http://KB.mozillazine.org/Profile_folder_-_Firefox
  • http://KB.mozillazine.org/Multiple_profile_files_created

  Delete sessionstore.js will cause App Tabs and groups of tabs open and closed tabs (back) to get lost and you will have to re-create them (take note or bookmarks if possible).