HA mixing different versions of ESX

Similar Questions

• vSphere Cluster with different Versions of ESX

  We plan to upgrade our ESX ESX ESXi 5.1 4.1 host our preferred is method of upgrade via the Update Manager. In the 5.1 Update Manager documentation it provides the following:

  "ESXi 4.x to 5.x UPGRADE ESXi is supported and ESX 4.1 for ESXi 5 MIGRATION is supported. Anyone know what are the difference between an upgrade and a migration? Am I'm going to completely rebuild the host or will it keep its settings.

  Also run different versions of inside ESX (ESX 4.1 and 5.1 ESXi) the same cluster, supported? Any other consideration when running different versions of the same cluster. It will be a temporary problem while we work to get all hosts upgrade.

  Thank you.

  J

  Migration - is where you perform the migration of ESXi 4.x for a new installation of ESXi 5 x

  Upgrade - is where you upgrade the existing ESXi 4.x host which will allow you to save the configuration of the host - things to keep in mind before you go is to ensure that existing equipment is supported by ESXi5 - you want to place the host to be upgraded in Maintenance mode - vCenter must be upgraded first

  As long as vCenter is upgraded to version 5.x versions of ESXi can coexist in a cluster

• HA can happen between a different version of ESX host

  I have two host ESX server, one is ESX 3.5 and the other is ESX 4, two of them are under the management of a VCenter server,

  I wonder if I can implement HA between the two ESX hosts

  Yes, this is supported.

  Elisha

• replication with different versions of vSphere vSphere

  After reviewing the matrix of interoperability of products, everything "looks" good, but caring for a second opinion.  See below:

  Environment:

  • vCenter 6 sites
  • PSC external sites
  • Protected site is vSphere 5.5 Update 2 or 3
  • Recovery site is vSphere 6.0 U2
  • vSphere 6.1 replication
  • 6.1 SRM

  Issues related to the:

  Can anyone confirm the support in regards to the different version of vSphere protected and recovery site?

  Are there related shades to have different versions of vSphere protected and recovery site?

  We can successfully failover to the recovery site, reprotect VMs to protected site and be restored in a site protected without problem?

  Different versions of vSphere are supported to recover protected site and as you have configured, it is recommended to have the new version on the recovering site. The reason for this and be careful about the different versions, has to do with the versions of virtual equipment. VMware ESX can run VMs with earlier versions of virtual hardware, but not later (came out after the version of vSphere). You want to make sure that your virtual machines will run on the host on the recovering site. If you are using a later version of vSphere to recovery, as long as you deploy new virtual machines when running it, or if you do this, you use a virtual hardware version that is compatible with the hosts what was your site protected, you will never come across the problem of trying to recover a virtual machine with the hardware version that is incompatible with vSphere.

  Issues related to the:

  Can anyone confirm the support in regards to the different version of vSphere protected and recovery site? -Yes

  Are there related shades to have different versions of vSphere protected and recovery site? -See above

  We can successfully failover to the recovery site, reprotect VMs to protected site and be restored in a site protected without problem? -Yes (see above)

  Does make sense?

• due to different VC Console ESX 3.0 and ESX3.5

  Hello

  all times can help me understand why esx 3.0 and 3.5 is using a different version of Virtual Center.

  For me, this is little uncomfortable because I'm managing different places, running with esx 3.0 and esx 3.5 and vice versa. Anyone know if the same console can be used for this purpose.

  I hope that page 2 will answer your question:

  http://www.VMware.com/PDF/vSphere4/R40/vsp_compatibility_matrix.PDF

  / Rubeck

• Have just been told by BT that I need a new/different version of Thunderbird to work with the new system BTMail (previously BTYahooMail) - I do?

  I have btinternet email for years and Thunderbird for too long and have been happy with both. Unfortunately, I'm not technical enough to understand the majority of assistance or instructions on the information pages of support technique/Thunderbird, but haven't managed to get TB put in place in the first place (long time) and it seems to have worked well since. However, on Friday both of my accounts to BT (sets of two numbers), so two BT email addresses have been moved new old BT Yahoo mail BT mail. I was unable to connect to one of them, but the other was very good - I have had help 'screen sharing' a technical chap BT to sort. However, he was able to Conect Thunderbird with email servers. I said to BT and the chap tech tried to sort on screen sharing, but could not (and I have been unable to follow what he was doing). A few months ago, I made a few changes, as requested by BT, to allow for the transfer to go smoothly (!), but the man has changed some things Friday, I think, as well. He could not solve the problem of TB and I can't figure it out at all, and the Lady of BT Tech help to whom I spoke this morning (and who had managed to fix my problem of connection BTID, fortunately) had a look and suggested that maybe I needed an update/new/different version TB or 'another email address. Well, I really want to stay with Thunderbird and was hoping that someone here could explain it in simple English for me, please? I was wondering what will happen, assuming that I need to download an updated version / different, if I did this and then sort of re-installed my existing BT email addresses (as if I started again with Thunderbird)? I hope that there is someone here who can help you - thank you - I'm rather fond of this little blue bird. Thank you.

  Hi, Zenos, thank you so much for your help - I have now (touch wood) have my email back after following your instructions. If all goes well, it will remain in operation during my upgrade to infinity next week.
  Thank you for taking the time to answer my question a little disjointed.
  Had never heard of before critical path, I thought that BTMail was BT Oh, well, as long as it works I guess (I hope it's better than the Yahoo system).
  Thanks again.

• FAQ (26): I installed a different version/version of Windows and now SDM will not show me updates.

  I installed a different version/version of Windows and now the SDM does not work in "Update" mode

  This can occur when some system that HP did not specifically tests with the model is installed and often happens with models and Windows Ultimate edition (or even 64-bit editions on some older models) before Windows 8 Ultimate.
  
  Because SDM detects the new operating system, but it cannot match in the SDM catalog, he (SDM) will disable mode "Update."  However, please note that you can still use SDM mode 'All products' to download your SoftPaqs by doing as follows (the Probook 4730 s is used as an example):

  1. Press the "view all products" in the SDM toolbar
  2. If a dialog box warning that "no operating system have been selected, then skip to step.
  3. Press OK to close the dialog box.
  4. Check the «Microsoft Windows 7 Professional 64 Edition»
  5. Click on the tab "language filter".
  6. 'English - International' is checked.
  7. Press the OK button.
  8. Now, expand the tree on the left side of the SDM application by selecting the following:
  9. HP Probook Notebook PC Series 4700
  10. HP Probook 4730 s Notebook PC
  11. Microsoft Windows 7 Professional Edition 64
  12. Check the box 'international - English.
  13. Press the button "find available SoftPaqs.
  14. After "things calm down", click on the button "See the last SoftPaqs" at the top right of the application of SDM.

  The latest list of the Softpaqs for your model should now be displayed. We recommend that you download all listed SoftPaqs. This whole new way SoftPaqs are released for this model will appear on the top list titled "Available SoftPaqs" display.

  To install a SoftPaq after downloading, do the SoftPaq to the ListView "Downloaded SoftPaqs" right click and select "install SoftPaq.

  Important note: most SoftPaqs listed using the method above should apply to your model, but a small number of SoftPaqs might not be applicable to your model due to the offers of different material for your model. This means that not all listed SoftPaqs will install on your model and that is normal.

• How can I run two different versions of Firefox, the last does not work with a site important I need to use?

  With the latest version of Firefox, I can't ' fast email ' to my students through the ANGEL of the College System. I had to uninstall and go to an earlier version. I prefer the new rev.

  A way to run two different versions. It doesn't have to be simultaneously. Seems to be a problem on the Mac and my XP systems.

  Thank you
  Kim

  You can install the portable version of Firefox 3.6.x to access Web sites that don't work with Firefox 5 +.

  • http://PortableApps.com/apps/Internet/firefox_portable#legacy
  • http://PortableApps.com/apps/Internet/firefox_portable/localization#legacy36

• Qosmio G30 - different versions between the NVIDIA drivers

  Hi all

  My question relates to the graphics card, I noticed that there are different versions in NVIDIA version v179.48 BETA site
  and the release of Toshiba v7.15.10.9813
  According to what is later? Which one should install?

  Thank you

  Hello

  Toshiba nVidia drivers are available for the use of the portable/mobile computer and the page of nvidia drivers are Commons drivers released for the nVidia chip such drivers can also be used on desktop PC.

  Usually, you must always use the Toshiba drivers, because these drivers have been tested and is supported by the overheating protection that helps protect the graphics chip of damage!

• Changed to different versions of existing songs

  I had a CD of the Soundtrack of the movie Sweeney Todd that I ripped in iTunes (more updated version) some time ago. Recently during playback of the album on my iPhone 5 (all updated), it changes some of the songs to those I've ever owned. Instead of the song "Bird of Finch and green Linnet" film, it has changed in the version of the song play, I have never possessed or downloaded what. I have nothing in the file of the song, and yet he is changed.

  It is an example of the problem. It also happens with various songs pop (they change to turn off karaoke brand versions, which I've never seen before).

  How iTunes or my iPhone do that? Its horrible and I want original songs from return.

  If you use iTunes game or services Apple music, your library is synchronized FRO a central source of iCloud. In this context the content on your computer is compared to the content that apple has in its collections, and if there is a match Apple will use its copy in the representation of your library iCloud.  I think that the game is fairly loose, so if you have a track named X by artist Y in your collection and Apple has one that is the same, but a different version, it will use rather than yours.  I do not use a service, so I can't speak from personal experience.  Maybe if you have renamed your titles they can not match and your will be get downloaded on your space in iCloud and unique pieces.

• Why does my 7th generation nano play different versions of the same song (acoustic, demo, replacing) one after another before she switches to a different song.

  Why does my 7th generation nano play different versions of the same song (acoustic, demo, replacing) one after another before she switches to a different song?

  Maybe the current list of the song has the songs listed in alphabetical order, and you have the iPod nano to play in the order of the list...  How do you think iPod nano to read the list of songs?

• same circuit design-different versions of multisim now fixed

  again the circuit model 74LS244N, now the pattern16t file works in different versions of multisim.

  How do you pattern16t signs might be useful.

  This circuit is interfaced with gpib, scsi, usb computer interface circuits.

  It's everything. software must always be carried out for each computer.

  Basically, there are computers with a different interface.

  Richard

  Hello

  The application seems interesting to interface with instruments or devices with these buses. Of course, it must take into account the fact that there are off-the-shelf products that come with the drivers, etc.

  Also, I really liked how you have organized the scheme in Multisim with bus, etc.

  Kind regards

• different versions of a program, subvies location

  Hello everyone,

  I have problem when I try to keep two different versions of a project in my PC. I developed a master project with a VI and severals subVIs. This project works correctly, but now I want to make some changes. Then I created another folder with a copy of this (kind of backup) program. However, when I opened the new version, there comes into conflict with the subvis two versions (old and new). And I wouldn't make some changes and modify the version of security and everytime I open a version should solve all conflicts either.

  You know any way to avoid this problem?

  Thank you!!

  1000 a,

  Probably you have copied your project directory in Windows Explorer.

  What you need to do to create an exact copy of the project and all content, is to open the project in LabVIEW, select "file > save as...". ", select the option 'Double' and then select the option 'include all the dependencies '.

  Now you must choose a folder where you want to save your project and the name you want to give to your project file. When you click 'OK' the project will be duplicated in the requested folder.

  Hope that answers your question.

  Kind regards

  Peter S

• The upgrade patch cannot be installed by the Windows Installer service because the program to be upgraded is may be missing, or the upgrade patch may update a different version of the program

  I try to use the Microsoft Office tool that implement an MSI for 64-bit Office 2010 installation file.  The tool works file and creates the msi file.  I get to the tool by going to the x 64-bit folder on the office 2010 installation disc.

  I install a new virtual machine from Windows 7 and tried to use the MSI file to install office 2010 and I get the error:

  "The upgrade patch cannot be installed by the Windows Installer service because the program to be upgraded is may be missing or the upgrade patch may update a different version of the program"

  If I just click Setup on the office 2010 dvd he moved very well on the same VM window7.

  Does anyone have an idea how do to understand why the windows installer keep fails or what he wants?

  If I click on the msi even on a system with office 2007 is installed, I get the same error.

  Thanks for the help

  jbabe

  Windows Update has nothing to do with the upgrade or installation of Office 2010. Please post future questions in this forum: http://social.answers.microsoft.com/Forums/en-US/officeinstall/threads

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Error message "the upgrade patch cannot be installed by the Windows Installer service because the program to be upgraded is may be missing or the upgrade patch may update a different version of the program."

  Original title: cannot install WMP11, update rollup 2

  I'm still on WMP 10 for a reason, and I wanted to connect my PC with 360 videos. I downloaded the update, but he told me to go get the Update Rollup 2 or something, so I tried to install it and he told me that I needed to go get the .NET framework 1.1 and .NET framework 1.1 SP1. I went to download them and install them, but he tells me that "the upgrade patch cannot be installed by the Windows Installer service because the program to be upgraded is may be missing or the upgrade patch may update a different version of the program".

  I Googled, tried of all kinds, uninstalled SP3 and tried and nothing.

  Hi xelliotx,
   
  I suggest that you follow these steps.
   
  Step 1:
   
  First of all, download and install .net Framework Cleanup Tool to remove selected versions of the .NET Framework on your computer.
   
  Step 2:
   
  Manually install the versions of Microsoft .NET Framework below:
   
  Microsoft .NET Framework Version 1.1 redistributable package
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=262D25E3-F589-4842-8157-034D1E7CF3A3&displaylang=en
   
  Microsoft .NET Framework 1.1 Service Pack 1
  http://www.Microsoft.com/downloads/details.aspx?FamilyID=a8f5654f-088e-40b2-bbdb-a83353618b38&displaylang=en
  Once this installation is complete, try to install the other required software and check.
   
  See also:
   
  Error message when you install an update for .NET Framework 1.1 or the .NET Framework 1.0: "the upgrade patch cannot be installed by the Windows Installer service.
  http://support.Microsoft.com/kb/940332
  
  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]