half-duplex configuration 9871
I am trying to configure a NI 9871 4 ports 485 series add-on half-duplex communication with non-echo. My problem is that I can not understand how to select the transmitter/receiver mode. Table 3 of the manual (http://www.ni.com/pdf/manuals/372277e.pdf) shows four different modes, but it's a mystery to me how to set the mode. The module is currently in mode 4-wire where the receiver is still active (if I connect the lines TX & RX, I recover what I send.) I would like to be in car 2-wire mode. Can someone point me in the right direction?
BTW: I use a cRIO-9075 mode of scanning and using Labview 2012 SP1 (windows), in the case where that matters.
Thank you.
Hi Tomherron,
If you use the Scan Mode you can set the Mode of the transceiver using a VISA property node. The process would be:
(1) place a property node VISA on the block diagram of your application.
"" 2) click on the property node and select: Select property "parameters set" thread Mode. This will allow you to set or get the wiring for a particular port mode. In addition, allows you to have different modes of thread for different ports.
(3) right-click and select any change in writing.
"(4) the method of wire with the right button and select Create ' constant.
(5) to choose what transceiver mode you want to use, click on the constant.
RS-485/2-EchoDTR and RS-485/2-Auto options. Those who are what you are looking for?
Kind regards
Kyle S.
Technical sales engineer
National Instruments
http://www.NI.com/support
Tags: NI Hardware
Similar Questions
-
CanI set programmatically PXI-8431 half duplex ports (two sons)?
Hello
I use an NI PXI-8431/8 RS485 card for half duplex comms. I use configuration of the serial port baud rate usual VISA, etc., but I also want to set the port to two sons, no handshake.
Currently I can do this from Windows, using the Device Manager, but it depends on someone who knows and not to forget to do. I want to automate so that it still occupies my entry into force, without worrying about who used it do.
Can anyone suggest how I can achieve this?
Thank you
Malcolm
Hi Malcolm,
You can set the thread mode and the type of control (handshaking) flow in LabVIEW using nodes of property.
The article in the link below shows how to do this at the end to set the thread mode. If you duplicate the property node, you can choose Flow Control as property instead of the thread Mode.
Setting the Mode of wireless transceiver on the Ports for the boards of the series NOR:
http://digital.NI.com/public.nsf/allkb/1D516C10D7EDFAC6862571110073B8F4
I hope this helps, please let me know if you have any questions.
Charlotte N
-
Hi need some help on this router cisco 1921 complete, auto & half duplex
We have this old 1841 router series and we change in 1921, I still put the same settings, but this two-sided thing is having problem (I think).
We are supposedly to have 20mbps up & download speed using this 1841, and if we use 1921 20down / 10upload speed.
When I put gi0/1 on full-duplex it will descend to the bottom. But if I set auto duplex, it register under the/s and half-duplex and the internet works but only 10 Mbps upload. See below
igabitEthernet0/1 is up, line protocol is up
Material is CN Gigabit Ethernet, the address is 0000000
Description: "connected to this."
The Internet address is 000000
MTU 1500 bytes, BW 100000 Kbit/s, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 13/255
Encapsulation ARPA, loopback not set
KeepAlive set (10 sec)
Half-Duplex, 100 Mbps, media type is RJ45
control output stream is not supported, control of input stream is not supported
Type of the ARP: ARPA, ARP Timeout 04:00
Last entry of 00:00:00, 00:00:00 exit, exit hang never
Final cleaning of "show interface" counters never
Input queue: 0, 75, 14, 10242 (size/max/drops/dumps); Total output drops: 79729
Strategy of queues: fifo
Output queue: 0/40 (size/max)
5 minute input rate 5400000 bps, packets/s 546
5 minute output rate 719000 bps, 390 packets/s
170608043 package, 1963069286 bytes, 79501 no input buffer
Received 477 broadcasts (0 of IP multicasts)
0 Runts, 0 giants, 4 controllers
entry 0, 0 CRC errors, frame 0, saturation 0, 0 ignored
Watchdog 0, multicast 0, break 0 comments
160510262 packets output, 1965851816 bytes, 0 underruns
0 output errors, 4095435 collisions, 0 resets interface
unknown protocol 0 drops
0 babbles, collision end 0, 0 deferred
carrier, 0 no carrier, lost 0 0 interrupt output
output buffer, the output buffers 0 permuted 0 failuresI really appreciate your comments and thank you
It is very likely that the provider has configured its device for 100 Mbps, which was compatible with the interface of your FE 1841. If you configure the 1921 at a fixed speed of 100 Mbps and full-duplex, it should probably work.
-
Configure the network adapter speed / bandwidth management
Hi all
In VMware ESX 4, it is possible to configure the speed of vmnic with a speed of diferent? I can do 10, 100, 1000 or full / half-duplex (photos attached) but... is possible to configure the speed of 4 MB, 40 MB or something different?
For bandwidth management, the best solution is the new Cisco device?
Thank you very much.
N ° negotiated between the physical NETWORK adapter and the physical switchport speed can be 10/100/1000. Just like in the physical world...
But you can do some of the traffic shaping based on your configuration... On a vSwitch standard you can control the evacuation traffic. On a distributed vSwitch, you control evacuation AND penetration.
/ Rubeck
-
New AirPort Extreme and 802.11ac configuration
Greetings,
I'll install a new new AirPort Extreme instead of my old Time Capsule gen1.
Like many people here, I have a combination of features b/g, n and ca. I want to make sure my end of 2013 iMac connects optimally via ac. It is in the line of fire of the new router in 25', so it should be in a good location, if all goes well.
My question is if I have to just put up an SSID and let devices their own switching group; or experienced here people recommend a SSID separated for the strip of the 5 GHz for ac and n devices?
Thank you!
Dave
Start with normal default values.
That is to say the band permutation is left to the Mac and SSID is the same on both bands.
If you then find that the Mac makes the wrong choice... a real possibility. And it's important for you... Then assign the SSID on 5 GHz a different name.
217Mbps is expected to reach a speed at 2.4 ghz and which probably exceeds the speed of your internet with a margin far... (you need at least 2 x the speed of wireless internet to follow, IE if internet is 100 Mbps Wireless should be 200 Mbit/s at least because of half duplex wireless nature). If you have several items that some should be forced to 5 GHz, which can control...
-
Dear team,
one of my vmnic shows me 100 half duplex if I put the same Auto negotiate, to 100 FUL harcode to 100FULL forcefully then it shows vmnic 100 FULL duplex. Can u please help me what is the problem
Concerning
MrVMware
A possible reason is that the switch port is on hard full duplex, this will make your esxi to half when using auto mode.
-
AirPlay - aTV video, sound effects for AExpress: does not work with large files
Hello!
My setup
- Internett--> modem (Cisco?) --> a/c Airport Extreme (latest high version)
- iMac, iPad, 2 x iPhones. iMac installed Beamer.
- Bedroom: AppleTV 3rd GEN rev A - hdmi--> LG TV (old). AirPlay ON, 'Apple TV room '. Connected to the local network of 5 GHz.
- Bedroom: AirportExpress 1st GEN 802.11 a/b/g N-Draft (last type of those that go right into the socket) with AirPlay - stereo--> stereo BOSE. AirPlay ON, 'room '. Connected to the local network of 5 GHz I also tried to connect 2.4 GHz network, no significant variation...
- Living room: AppleTV 4th Gen. - hdmi--> LG TV (new). AirPlay ON, "iTV."
Problem (abridged version)
Most of the time - but not every time - when I stream video + audio iMac to aTV and choose to listen to the audio portion of the aTV to a separate AExpress (which is connected to a better BOSE audio system), the movie will not play. Streaming both audio and video - and only - the aTV works perfectly, but then I have bad sound, since I use the TV's internal speakers. What is reasons for it? Tips to fix it?
Problem (full version)
Every time when I stream video and audio from large multimedia files (about 3-4 GB .mkv) of the iMac (Beamer) on the ATV to the room, I didn't encounter any problem. Buffering is fast (2-4) and there is no delay or other negative experience. Unfortunately, as with all flat TVs, the sound of the TV is poor. Since I have a BOSE sound system, placed around this TV, I like to use it for audio. As I do this is - after the streaming media file (Beamer) iMac to the bedroom aTV - pressing the Center "Select" button during 1 sec on the remote to display the "audio" preferences and select money "Chamber" (AExpress related to the BOSE sound system). In this way, I think that audio + video is streamed to the iMac on the ATV in the bedroom, and the sound is then broadcast the ATV to the AExpress. This is where the problem occurs. Sometimes it works very well, as today in the morning. No lag and everything works fine. But most of the time, after changing the preference "audio" in the sound stream for the BOSE, the beginning of the play symbol buffering becomes the symbol of the break and nothing happens. I hit play again and the symbol of the game / buffering symbol lights up for a few seconds, and then again to pause. She never starts.
The problem usually occurs with heavy multimedia files / large size 1080 p and 3-4 GB, not with the simplest 720 p files weighing about 1 to 2 GB. This makes me think it's a matter of WiFi capability. But if my WiFi network should not be able to manage that? I think that the apple TV in the bedroom and the AExpress uses the N standard, so it is the limiting factor. But if this interface should not be able to handle the traffic? Is it true that do what I do - separate the video and audio - use twice the network traffic?
I also want to mention that everything works perfectly at certain times, like this morning. Last night (12 h) it wouldn't work at all... Perhaps there are more traffic yesterday (Saturday) evening.
Questions (summarizes all Qs in text and some new)
- My network be able to handle the traffic encountered at the stream video + audio iMac to mountain BIKING in the room and streaming audio of ATV to AExpress at the same time?
- It is true that this configuration requires / use twice the network resources?
- Do you also think that my problem is caused by a network limited issue / the amount of data PR. second?
- I have a new (flat unit with power cord separate) Airport Express. This device manage more traffic and thus possibly resolve my problem?
- Other suggestions to solve my problem?
Sorry for long post, but I think that its better with much info little. Have a great Sunday =)
I think I can explain the reason for the problem... but I have little experience with sound problems... so you will need to figure out a work around.
The nature of wireless networks, it's to manage the stream very well... but they are much less good at the sensitive time of things like multimedia transmission continuously. In fact, if you want to stream multimedia content over wireless, it is preferable to use specialized units... no wifi. I have a 3D projector and home theater system that uses a special wireless link from Epson to the projector... It is amazing that it can handle the required data of 3D projection. It does so by using 60GHz or some these extremely high FREQ... and totally dedicated units... no wifi. In the end, we ran an HDMI cable in the wall... it was largest wireless but not could be started reliably. Wireless is simply not ready for the big time of streaming video high definition even when dedicated.
Wireless network adapter... It is wifi, can handle only one connection at a time and it time slices between clients. It's also half-duplex, so it can only send or receive... it can't do both at the same time.
On the other hand, modern interrrupteurs ethernet can stream to multiple devices at the same time. It can also handle send them and receive at the same time... That is to say in full duplex. This is why the networks ethernet much more suitable for media streaming wireless never can be.
As soon as you try to use double flow... even if it is audio (low bandwidth) and a video (broadband), you will cause huge delays to the video component. The video stream has literally if stop to give the time to the audio to catch up... you can immediately see where this will lead. Low resolution, it might work... but at high resolution, there is bandwidth inadequate considering the Division of time.
It would be much better to use the audio on the TV. Or check if the TV itself has audio output... that plug into the standard analog audio system RCA or it could even have out optical. Who will then provide a means by which the flow must not be split. My samsung smart TV offers you both.
The other solution probably won't be viable... execution of ethernet.
-
Read only the SPI using the box USB-8451
I am using the NI USB-8451 box to read the SPI of a Honeywell digital pressure transducer data. The difficulty comes from that part of Honeywell uses only the SPI in half-duplex mode, meaning that it only transmits data, but does not require anything beyond the appropriate chip select signal and SCLK to start transmitting its 32-bit sensor data. To facilitate experimentation with the sensor, I bought a USB-8451 SPI Interface thinking I could easily configure the 8451 to read data from the sensor.
However, if I understand the situation, there is a problem. The 8451 considers full duplex data, i.e. a data word must first be sent to the SPI device in question before the unit will start to transmit back data of its own. And since the MOSI data writing periods, since this particular device starts transmitting immediately once a clock is applied, synchronizing the unused address data will cause the unit will return its data before the 8451 begins listening for data in return. The call used by the 8451 to write read action can be divided into the individual reading and actions of writing of any kind that I could discover.
Can someone tell me if I missed something in this operation or if there is some quick tips, that I could use to be able to use the 8451 therefor? Thank you!
Doug G.
Exactly correct. It's nice when things are easier than expected. Hope it works as easy as it sounds.
-
Connection RS-485 for the climate control ESPEC Chamber
Hi all
I'm having some difficulties of implementation and the RS485 connection with ESPEC climate control room.
It is a room of climate ARL-0680. The climate Chamber has two connectors male DB9 on the outside, apparently used to connect several rooms to RS - 485.
The pinout of the connector RS485 DB9 real is:
1: Data Transmission SD + (A) connected
2: SD-Transmission data (B) connected
3: data reception RD + (A) connected
4: data RD-reception (B) connected
5: GND mass connected
6: GND mass connected
7: NC (not connected) not connected
8: NC (not connected) not connected
9: NC (not connected) not connected
I bought a cable interface OR USB-485. This cable also has a DB9 Male interface but the pinout is different.
1: GND
2: CTS + (HSI)
3: RTS + (HSO)
4: RXD +.
5: RXD -.
6: CTS-(HSI) -
7: RTS-(SSA) -
8: TXD +.
9: TXD -.
-The list of the pins do not match and I see names of different signals on both interfaces.
Am I right assuming that I should only make the following connections:
USB485 NOR to the climate Chamber ESPEC
1 5, 6
2 not connected
3 not connected
4 3
5 4
6 not connected
7 not connected
8 1
9 2
Is there some special things I need to do in SW for this configuration to work? I'm using LabVIEW as my programming language to try to control the climate Chamber.
I especially do not know how I need to put in place the transmitter/receiver mode for all either works...
ESPEC documentation, I found that the communication system used is 'synchronized Modulation (four sons, half duplex).
Thank you 1 million for all of your helpful comments!
K.
You connected Rx to Rx and Tx of Tx.
You must connect Tx Rx and Tx Rx. In this way, you create a four-wire interface. Also, you must set your Board of Directors (MAXIMUM) 4-wire.
To make it perfect, you should also connect a 120 Ohm resistor at each end of the balanced line. So in total 4 resistors.
If you want I can draw you a picture to replace these (1 k) words.
Kees
-
connection intermittent cRIO (with MAX, etc.)
Our cRIO connects to our fine PC when it is initialized at first - and you can view it fine in MAX, Manager of distributed system and its web interface. But after all 3-5 minutes it always loses connection. It remains disconnected, and only restart the cRIO restores the connection but only for another 3-5 minutes. Only MAX restart does not help. We can ping the cRIO ok when 'disconnected' - which, to me, implies that it is a problem of higher level software.
We had this particular cRIO work fine before.
Thanks for your suggestions... While not in a rush to do this, I really want to understand why the connection is intermittent
Here are some details:
- MAX version 5.0.0f1
- LV2011 DS2
- cRIO is a 9022 (no screws running on it to the commissioning, CPU minimum load - idle = 97%)
- computer development is a Vista Home Premium 32 bit
- connected together using the brand-new Cat5E cable
- TCP/IP settings on the laptop - Static IP, IP 192.168.2.4 address, mask 255.255.255.0
- TCP/IP settings on cRIO - Static IP, the IP 192.168.2.1, mask 255.255.255.0 (gateway and DNS are blank or 0.0.0.0)
- cRIO set to use for the link speed autonegotiation (no option to change this) and detection of packets = "interrupt".
- PC value link autonegotiation speed, but has no effect on the problem, if it is set on a fixed, low speed for example. Half-Duplex 10 Mbps
- PC Firewall is configured to allow the port 3580, and actually disable the firewall altogether change the problem
Had the chance to try again with my intermittent connection to cRIO, and here's what I found:
- Connection through a switch, rather than directly with crossover cable - made no difference, still kept disconnecting after 3-4 minutes
- With no other network on my laptop other than the LAN - no difference development
- cRIO with APP No. dip switch select IT - no difference
- cRIO with game of dip-switch SAFE MODE - this time it is remained connected, but this mode is not very useful as a solution
Then I was reinstalling the software cRIO as suggested - it did not complete the first time, but second attempt was beautiful and connection is now very stable (and has not abandoned in the last 30 minutes).
Here are the instructions to reinstall (just in case useful for others):
- In the measurement and Automation Explorer (MAX), access remote systems | cRIO | Software
- Click on the "Add/Remove software", and an installation wizard will appear
- With currently installed version of the selected software - "then click to reinstall the software currently installed.
- Follow the rest of the instructions, and it should take about 4-5 minutes
Thanks for your help
Andy
-
Well, as evidenced by my increase in the issue positions (vs answer my other posts), I get down to the wire trying to get a new operating system. I'm controlling a Hitachi L300P inverter (motor controller), via its RS485 link. I have, at the end of the computer, a usb to RS485 adapter, and the race to the L300P made by a short, twisted pair (60 feet max) runs (the controller is configured for "Half duplex, two sons"). When I send a message to the unit I get no response, the purpose, or a message ACK or NAK. I tested my port by connecting a second and "talking to myself", performed the L300P self back loop, which is to unplug the external connection and do manual things through its programming before Panel and have, while the cable was disconnected tested its continuity. This morning I intend on executing the second long twisted of the location of the computer for controllers and make one end to end test to confirm I can talk down the wires. I'm sure that my chain of command is correct, but do think the device is supposed to send an ACK or NAK if it "sees" something coming.
If there is anyone who has had experience with these discs, either through LabVIEW or not, I would be grateful hearing on their part. Also all other paths to solve this are appreciated. I'm more tired, mentally and physically, and another set of "eyes" looking at the problem will probably help.
Well, to help anyone with similar problems, I'll say what I found. As mentioned in previous posts, I had ran 150' cable out to the fine disc and connected to the other end of the cable comm existing on the disc, the near end of another adapter USB-RS485 (Easysync ES-U-3001-M). When it worked, I thought it turned out that the problem is not hardware but whatever my software (doubtful, the sent string implementation match the example in the manual) or a problem of disk configuration. While I was talking to 'Sam' to Hitachi, I found that once I sent the order message I received a returned "ACK" message. Hmmm! ?? Well, the USB adapter, I, designed to be used as RE232, 422 or 485, has a number of configuration inside bars, which allow the addition of 750 ohms pullups and pulldowns and 120 ohm termination resistors to some signals. I activated the and "Bam!" the reader begins to see and responding to my messages. Apparently, the cards have a more sensitive front end that are matched to the car, or at least (reasonable) to communicate successfully more than ~ 300 feet of twisted out of the box configuration, pair but the necessary drive configuration changes. Still have a big headache (a real one) and I now talk to other Hitachi drive, which uses Modbus rather than the simple protocol of this player.
Thanks again for the support, it can feel pretty lonely here with you people!
-
DirectX is not found and can not be installed due to an internal error?
There is no version of directx on my computer whenever I run dxdiag. Whenever I try to install the latest version of Directx configuration DX of Microsoft, it gives me an error and States in order to check the dxlog. I did almost everything on the internet that has been said, I deleted my records which have dirtied DirectX, I also downloaded registry fixers who have not helped at all, none so far can help me solve this problem. Here is my log of directx:
------------------
Information System
------------------
Time of this report: 11/11/2009, 10:20:48
Computer name: D8699BBF1ABC485
Operating system: Windows XP Professional (5.1, Build 2600) Service Pack 3 (2600.xpsp_sp3_gdr. 090804-1435)
Language: English (regional setting: English)
System manufacturer: system manufacturer
System model: System product name
BIOS: Phoenix - AwardBIOS v6.00PG
Processor: AMD Athlon (TM) 64 X 2 Dual Core Processor 3800 +, MMX, 3DNow (2 CPUs), ~2.0GHz
Memory: 2048 MB RAM
Page file: 366MB used, 3573 MB of available space
Windows Dir: C:\WINDOWS
DirectX version: not found
DX setup parameters: not found
DxDiag Version: 5.03.2600.5512 32 bit Unicode------------
DxDiag Notes
------------
The DirectX files tab: the gcdef.dll file is an older version, which could cause problems.
Display 1 tab: No problems found.
Sound tab 1: No problems found.
Music tab: no problems found.
Input tab: no problems found.
The network tab: no problems found.--------------------
DirectX Debug levels
--------------------
Direct3D: 0/4 (n/a)
DirectDraw: 0/4 (detail)
DirectInput: 0/5 (n/a)
DirectMusic: 0/5 (n/a)
DirectPlay: 0/9 (detail)
DirectSound: 0/5 (retail)
DirectShow: 0/6 (detail)---------------
Display devices
---------------
Card name: NVIDIA GeForce 9800 GTX/9800 GTX +.
Manufacturer: NVIDIA
Track type: GeForce 9800 GTX/9800 GTX +.
DAC type: Integrated RAMDAC
The device key: Enum\PCI\VEN_10DE & DEV_0612 & SUBSYS_23731682 & REV_A2
Display memory: 512,0 MB
Current mode: 1024 x 768 (32 bit) (60 Hz)
Monitor: Plug-and-Play monitor
Monitor Max Res: 1600,1200
Driver name: nv4_disp.dll
Driver version: 6.14.0011.9107 (English)
The DDI Version: 9 (or higher)
Driver attributes: Final retail
Format/driver Date: 2009-09-27 15:12:22, 5900416 bytes
Would be WHQL logo: Yes
WHQL Date stamp: n/a
VDD: n/a
Mini VDD: nv4_mini.sys
Mini VDD Date: 2009-09-27 15:12:22, 7655872 bytes
The instrument identifier: {D7B71E3E-4552-11CF-A156-780303C2CB35}
Vendor ID: 0x10DE
Device ID: 0 x 0612
SubSys ID: 0 x 23731682
Revision ID: 0x00A2
Revision ID: 0x00A2
Video Accel: ModeMPEG2_C ModeMPEG2_D
Deinterlace caps: {6CB69578-7617-4637-91E5-1C02DB810285}: caps Frames(Prev/Fwd/Back) = (0,0,0) (In/Out) Format (YUY2, YUY2) = VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_PixelAdaptive
{335AA36E-7884-43A4-9C91-7F87FAF3E37E}: caps Frames(Prev/Fwd/Back) = (0,0,0) (In/Out) Format (YUY2, YUY2) = VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_BOBVerticalStretch
{6CB69578-7617-4637-91E5-1C02DB810285}: caps Frames(Prev/Fwd/Back) = (0,0,0) (In/Out) Format (UYVY, YUY2) = VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_PixelAdaptive
{335AA36E-7884-43A4-9C91-7F87FAF3E37E}: caps Frames(Prev/Fwd/Back) = (0,0,0) (In/Out) Format (UYVY, YUY2) = VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_BOBVerticalStretch
{6CB69578-7617-4637-91E5-1C02DB810285}: caps Frames(Prev/Fwd/Back) = (0,0,0) (In/Out) Format (YV12, 0x3231564e) = VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_PixelAdaptive
{335AA36E-7884-43A4-9C91-7F87FAF3E37E}: caps Frames(Prev/Fwd/Back) = (0,0,0) (In/Out) Format (YV12, 0x3231564e) = VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_BOBVerticalStretch
{6CB69578-7617-4637-91E5-1C02DB810285}: caps Frames(Prev/Fwd/Back) = (0,0,0) (In/Out) Format (NV12, 0x3231564e) = VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_PixelAdaptive
{335AA36E-7884-43A4-9C91-7F87FAF3E37E}: caps Frames(Prev/Fwd/Back) = (0,0,0) (In/Out) Format (NV12, 0x3231564e) = VideoProcess_YUV2RGB VideoProcess_StretchX VideoProcess_StretchY DeinterlaceTech_BOBVerticalStretch
Registry: OK
DDraw status: enabled
D3D status: enabled
AGP status: enabled
DDraw Test result: does not work
D3D7 Test result: does not work
D3D8 Test result: does not work
D3d9 Test result: does not work-------------
Sound Devices
-------------
Description: SB X - Fi Audio [8000]
Default audio playback: No.
Default voice playback: no
Hardware ID: PCI\VEN_1102 & DEV_0005 & SUBSYS_10031102 & REV_00
Manufacturer ID: 1
Product ID: 100
Type: WDM
Driver name: ctaud2k.sys don't
Driver version: 6.00.0001.1373 (English)
Driver attributes: Final retail
WHQL Logo would be: n/a
Date and size: 2009-06-04 01:47:14, 526232 bytes
Other files:
Driver provider: creative
HW Accel level: full
Cap flags: 0x0
Min/Max sample rate: 0, 0
Static/Strm HW Mix beef: 0, 0
Static/Strm HW 3D steers: 0, 0
HW memory: 0
Management of the voice: No.
Listen/Src/EAX (TM) 2.0: No, no
Listen/Src/I3DL2 (TM): No, no
Sensaura (TM) ZoomFX (tm): No.
Registry: OK
Sound Test result: does not work---------------------
Sound Capture devices
---------------------
Description: SB X - Fi Audio [8000]
Capture audio by default: No.
Default voice Capture: No.
Driver name: ctaud2k.sys don't
Driver version: 6.00.0001.1373 (English)
Driver attributes: Final retail
Date and size: 2009-06-04 01:47:14, 526232 bytes
Cap flags: 0x0
Format flags: 0x0Description: AK5370
Capture audio by default: No.
Default voice Capture: No.
Driver name: usbaudio.sys
Driver version: 5.01.2600.5512 (English)
Driver attributes: Final retail
Date and size: 2008-04-13 23:15:14, 60032 bytes
Cap flags: 0x0
Format flags: 0x0-----------
DirectMusic
-----------
DLS Path: C:\WINDOWS\SYSTEM32\drivers\GM. DLS
DLS Version: 1.00.0016.0002
Acceleration: enabled
Ports: SB X - Fi DMusic synthesizer [8000], hardware (Kernel Mode), output, DLS, internal, default Port
MPU-401, hardware (Kernel Mode), entered, no DLS, external
MPU-401, hardware (Kernel Mode), output, no DLS, external
SB X - Fi Audio [8000], software (Kernel Mode), output, DLS, internal
The MIDI Mapper Microsoft [emulated], hardware (not Kernel Mode), output, no DLS, internal
SB X - Fi Synth has [8000] [emulated], hardware (not Kernel Mode), output, no DLS, internal
MPU - 401 [emulated], hardware (not Kernel Mode), output, no DLS, external
SB X - Fi Synth B [8000] [emulated], hardware (not Kernel Mode), output, no DLS, internal
Hardware (not Kernel Mode), output, no DLS, internal, Microsoft GS Wavetable SW Synth [emulated]
MPU - 401 [emulated], hardware (not Kernel Mode), entry, no DLS, external
Microsoft SoftSynth (not Kernel Mode), output, DLS, internal
Registry: OK
Test result: does not work-------------------
DirectInput devices
-------------------
Device name: mouse
Joint: 1
Controller ID: n/a
Vendor/product ID: n/a
FF driver: n/aDevice name: keyboard
Joint: 1
Controller ID: n/a
Vendor/product ID: n/a
FF driver: n/aDevice name: keyboard of Logitech game
Joint: 1
Controller ID: 0 x 0
Suppliers of products/ID: 0x046D, 0xC221
FF driver: n/aDevice name: keyboard of Logitech game
Joint: 1
Controller ID: 0 x 0
Suppliers of products/ID: 0x046D, 0xC221
FF driver: n/aDevice name: G15 Keyboard
Joint: 1
Controller ID: 0 x 0
Suppliers of products/ID: 0x046D, 0xC222
FF driver: n/aDevice name: USB receiver
Joint: 1
Controller ID: 0 x 0
Suppliers of products/ID: 0x046D, 0xC51A
FF driver: n/aDevice name: USB receiver
Joint: 1
Controller ID: 0 x 0
Suppliers of products/ID: 0x046D, 0xC51A
FF driver: n/aDevice name: USB receiver
Joint: 1
Controller ID: 0 x 0
Suppliers of products/ID: 0x046D, 0xC51A
FF driver: n/aPoll w / Interrupt: No.
Registry: OK-----------
USB devices
-----------
+ USB root hub
| Suppliers of products/ID: 0x10DE, 0x005A
| Matching Device ID: usb\root_hub
| Service: usbhub
| Driver: usbhub.sys, 2008-04-13 23:15:38, 59520 bytes
| Driver: usbd.sys, 23/08/2001 07:00, 4736 bytes
|
+ - + Generic USB hub
| | Suppliers of products/ID: 0x046D, 0xC223
| | Geographical area: Logitech G15 Keyboard
| | Matching Device ID: usb\class_09
| | Service: usbhub
| | Driver: usbhub.sys, 2008-04-13 23:15:38, 59520 bytes
| |
| + - + USB Human Interface Device
| | | Suppliers of products/ID: 0x046D, 0xC222
| | | Geographical area: G15 Keyboard
| | | Matching Device ID: usb\class_03
| | | Service: HidUsb
| | | Driver: hidusb.sys, 2008-04-13 23:15:28, 10368 bytes
| | | Driver: hidclass.sys, 2008-04-13 23:15:28, 36864 bytes
| | | Driver: hidparse.sys, 2008-04-13 23:15:24, 24960 bytes
| | | Driver: hid.dll, 14/04/2008 04:51:44, 20 992 bytes
| | |
| | + - + HID-compliant device
| | | | Suppliers of products/ID: 0x046D, 0xC222
| | | | Matching Device ID: hid_device
| | | |
| | + - + HID keyboard device
| | | | Suppliers of products/ID: 0x046D, 0xC222
| | | | Matching Device ID: hid_device_system_keyboard
| | | | Service: kbdhid
| | | | Driver: kbdhid.sys, 2008-04-13 23:09:50, 14592 bytes
| | | | Driver: kbdclass.sys, 2008-04-13 23:09:48, 24576 bytes----------------
Gameport devices
----------------
+ PCI bus
| Matching Device ID: * pnp0a03
| Service: pci
| Driver: pci.sys, 2008-04-13 23:06:46, 68224 bytes
|
+ - + Standard game port
| | Matching Device ID: * pnpb02f
| | Service: gameenum
| | Driver: gameenum.sys, 2008-04-13 23:15:30, 10624 bytes------------
PS/2 devices
------------
+ Keyboard HID device
| Suppliers of products/ID: 0x046D, 0xC221
| Matching Device ID: hid_device_system_keyboard
| Service: kbdhid
| Driver: kbdhid.sys, 2008-04-13 23:09:50, 14592 bytes
| Driver: kbdclass.sys, 2008-04-13 23:09:48, 24576 bytes
|
+ Server terminal keyboard driver
| Matching Device ID: root\rdp_kbd
| High filters: kbdclass
| Service: TermDD
| Driver: termdd.sys, 14/04/2008 04:43:22, 40840 bytes
| Driver: kbdclass.sys, 2008-04-13 23:09:48, 24576 bytes
|
+
| Suppliers of products/ID: 0x046D, 0xC51A
| Service: me
|
+ Terminal Server mouse driver
| Matching Device ID: root\rdp_mou
| High filters: mouclass
| Service: TermDD
| Driver: termdd.sys, 14/04/2008 04:43:22, 40840 bytes
| Driver: mouclass.sys, 2008-04-13 23:09:48, 23040 bytes----------------------------
DirectPlay service providers
----------------------------
Connection Internet TCP/IP for DirectPlay - registry: OK, file: dpwsockx.dll (5.03.2600.5512)
Connection IPX for DirectPlay - registry: OK, file: dpwsockx.dll (5.03.2600.5512)
Connection modem for DirectPlay - registry: OK, file: dpmodemx.dll (5.03.2600.5512)
Serial connection for DirectPlay - registry: OK, file: dpmodemx.dll (5.03.2600.5512)DirectPlay Voice wizard tests: Full Duplex: not run, Half Duplex: doesn't work don't not, Mic: does not work
The DirectPlay Test result: Does not work
Registry: OK-------------------
DirectPlay adapters
------------------------------------------
DirectPlay Voice Codecs
------------------------------------------------
DirectPlay Lobbyable Apps
-------------------------------------------------
Disk & CD-ROM/DVD-ROM readers
------------------------
Drive: C:
Free space: 53.8 GB
Total space: 152,6 GB
File system: NTFS
Model: n/aDrive: E:
Free space: 236,5 GB
Total space: 238.5 GB
File system: NTFS
Model: WDC WD2500JB-00REA0Drive: D:
Model: _NEC DVD + RW ND-2100AD
Driver: c:\windows\system32\drivers\cdrom.sys, 5.01.2600.5512 (English), 2008-04-13 23:10:48, 62976 bytes--------------
System devices
--------------
Name: Marvell Yukon 88E8001/8003/8010 PCI Gigabit Ethernet Controller #2
Device ID: PCI\VEN_11AB & DEV_4320 & SUBSYS_811A1043 & REV_13\4 & 15B9AB7D & 0 & 6048
Pilot: s/oName: Creative SB X - Fi
Device ID: PCI\VEN_1102 & DEV_0005 & SUBSYS_10031102 & REV_00\4 & 15B9AB7D & 0 & 4048
Driver: C:\WINDOWS\system32\ksuser.dll, 5.03.2600.5512 (English), 2008-04-14 04:41:58, 4 096 bytes
Driver: C:\WINDOWS\system32\ksproxy.ax, 5.03.2600.5512 (English), 2008-04-14 04:42:44, 129536 bytes
Driver: C:\WINDOWS\system32\drivers\ks.sys, 5.03.2600.5512 (English), 2008-04-13 23:46:38, 141056 bytes
Driver: C:\WINDOWS\system32\drivers\drmk.sys, 5.01.2600.5512 (English), 2008-04-13 23:15:16, 60160 bytes
Driver: C:\WINDOWS\system32\drivers\portcls.sys, 5.01.2600.5512 (English), 2008-04-13 23:49:42, 146048 bytes
Driver: C:\WINDOWS\system32\drivers\stream.sys, 5.03.2600.5512 (English), 2008-04-13 23:15:16, 49408 bytes
Driver: C:\WINDOWS\system32\wdmaud.drv, 5.01.2600.5512 (English), 2008-04-14 04:42:46, 23552 bytes
Driver: C:\WINDOWS\system32\drivers\ctac32k.sys, 6.00.0001.1361 (English), 04/06/2009 01:47:06, 511000 bytes
Driver: C:\WINDOWS\system32\drivers\ctaud2k.sys, 6.00.0001.1373 (English), 04/06/2009 01:47:14, 526232 bytes
Driver: C:\WINDOWS\system32\drivers\ctoss2k.sys, 6.00.0001.1373 (English), 04/06/2009 01:47:34, 130072 bytes
Driver: C:\WINDOWS\system32\drivers\ctprxy2k.sys, 6.00.0001.1373 (English), 04/06/2009 01:47:42, 14360 bytes
Driver: C:\WINDOWS\system32\drivers\ctsfm2k.sys, 6.00.0001.1373 (English), 04/06/2009 01:47:50, 158744 bytes
Driver: C:\WINDOWS\system32\drivers\emupia2k.sys, 6.00.0001.1373 (English), 04/06/2009-01:48, 95768 bytes
Driver: C:\WINDOWS\system32\drivers\ha20x2k.sys, 6.00.0001.1373 (English), 2009-06-04 01:48:12, 1177624 bytes
Driver: C:\WINDOWS\system32\drivers\pfmodnt.sys, 3.00.0000.0012 (English), 2009-06-04 01:48:20, 15384 bytes
Driver: C:\WINDOWS\system32\drivers\CTEXFIFX.sys, 6.00.0001.1373 (English), 04/06/2009 01:46:56, 1324056 bytes
Driver: C:\WINDOWS\system32\drivers\CT20XUT.sys, 6.00.0001.1373 (English), 04/06/2009 01:46:34, 171032 bytes
Driver: C:\WINDOWS\system32\drivers\CTHWIUT.sys, 6.00.0001.1373 (English), 04/06/2009 01:46:42, 72728 bytes
Driver: C:\WINDOWS\system32\ctdlang.dat, 2009-06-03 23:40:44, 321512 bytes
Driver: C:\WINDOWS\system32\ctdnlstr.dat, 2009-06-03 23:40:44, 56509 bytes
Driver: C:\WINDOWS\system32\CtxfiRes.dll, 6.00.0001.1373 (English), 2009-06-03 23:55:20, 2560 bytes
Driver: C:\WINDOWS\system32\ctzapxx.ini, 2009-06-04 00:37:06, 54 bytes
Driver: C:\WINDOWS\system32\instwdm.ini, 2009-06-04 00:37:08, 21093 bytes
Driver: C:\WINDOWS\system32\CT1MGM. ROME, 25/02/2000 11:49:34, 1048576 bytes
Driver: C:\WINDOWS\system32\CT2MGM. SF2, 22/09/1999 22:18:38, 2167684 bytes
Driver: C:\WINDOWS\system32\default4.sfm, 2002-01-03 14:44:16, 59 bytes
Driver: C:\WINDOWS\system32\default8.sfm, 2002-01-03 14:44:16, 59 bytes
Driver: C:\WINDOWS\system32\default.sfm, 2002-01-03 14:44:16, 59 bytes
Driver: C:\WINDOWS\Temp\ctpxst32.exe, 1.01.0000.0059 (English), 13/03/2007 09:32:14, 89336 bytes
Driver: C:\WINDOWS\Temp\cttele32.dll, 1.00.0011.0000 (English), 2008-02-04 09:27:58, 102400 bytes
Driver: C:\WINDOWS\system32\regplib.exe, 2009-06-03 23:36:30, 16384 bytes
Driver: C:\WINDOWS\system32\a3d.dll, 80.00.0000.0003 (English), 03/06/2009-23:57:38, 60928 bytes
Driver: C:\WINDOWS\system32\ac3api.dll, 6.00.0001.1373 (English), 03/06/2009-23:56:36, 48640 bytes
Driver: C:\WINDOWS\system32\eaxac3.dll, 1.01.0002.0000 (English), 11/07/2001 09:51, 77824 bytes
Driver: C:\WINDOWS\system32\ctosuser.dll, 6.00.0001.1373 (English), 03/06/2009-23:36:38, 74752 bytes
Driver: C:\WINDOWS\system32\ctemupia.dll, 6.00.0001.1373 (English), 03/06/2009-23:40:12, 114688 bytes
Driver: C:\WINDOWS\system32\piaproxy.dll, 6.00.0001.1373 (English), 03/06/2009-23:36:26, 68608 bytes
Driver: C:\WINDOWS\system32\ctdproxy.dll, 6.00.0001.1373 (English), 03/06/2009-23:37, 53248 bytes
Driver: C:\WINDOWS\system32\devreg.dll, 6.00.0001.1373 (English), 03/06/2009-23:31:56, 36864 bytes
Driver: C:\WINDOWS\system32\ctasio.dll, 6.00.0001.1373 (English), 03/06/2009-23:37:04, 50688 bytes
Driver: C:\WINDOWS\system32\ct_oal.dll, 6.00.0001.1373 (English), 03/06/2009-23:37:06, 193024 bytes
Driver: C:\WINDOWS\system32\ctpxst32.exe, 1.01.0000.0059 (English), 13/03/2007 09:32:14, 89336 bytes
Driver: C:\WINDOWS\system32\UDAAIM32.exe, 2.47.0000.0000 (English), 2009-03-26 15:09:18, 600217 bytes
Driver: C:\WINDOWS\system32\oalinst.exe, 2.00.0006.0000 (English), 2008-04-23 05:07:50, 805400 bytes
Driver: C:\WINDOWS\system32\AddCat.exe, 0.00.0000.0001 (English), 12/05/2006 13:52:40, 48400 bytes
Driver: C:\WINDOWS\system32\UDAAPO32. UDA, 12/05/2009 17:34:56, 8046 bytes
Driver: C:\WINDOWS\system32\CTMLFX32. UDA, 02/06/2008 10:10:04, 5458 bytes
Driver: C:\WINDOWS\system32\AppSetup.exe, 1.00.0018.0005 (English), 18/05/2009 13:34:30, 22691984 bytes
Driver: C:\WINDOWS\system32\CTxfiBtn.dll, 6.00.0001.1373 (English), 2009-06-03 23:55:20, 41472 bytes
Driver: C:\WINDOWS\system32\CTxfiSpk.dll, 6.00.0001.1373 (English), 03/06/2009-23:55:18, 39424 bytes
Driver: C:\WINDOWS\system32\Ct20xspi.dll, 6.00.0001.1373 (English), 03/06/2009-23:50:04, 15360 bytes
Driver: C:\WINDOWS\system32\CTxfispi.exe, 6.00.0001.1373 (English), 03/06/2009-23:49:56, 1213440 bytes
Driver: C:\WINDOWS\system32\Ctxfihlp.exe, 6.00.0001.1373 (English), 03/06/2009-23:55:16, 25600 bytes
Driver: C:\WINDOWS\system32\CTxfiReg.exe, 6.00.0001.1373 (English), 03/06/2009-23:50:08, 47104 bytes
Driver: C:\WINDOWS\system32\enlocstr.exe, 2009-06-03 23:33:04, 7680 bytes
Driver: C:\WINDOWS\system32\killapps.exe, 1.00.0000.0001 (English), 03/06/2009-23:32:54, 12800 bytes
Driver: C:\WINDOWS\system32\kill.ini, 2009-05-27 08:49, 285 bytes
Driver: C:\WINDOWS\system32\sfman32.dll, 6.00.0001.1373 (English), 03/06/2009-23:36:36, 10240 bytes
Driver: C:\WINDOWS\system32\sfms32.dll, 6.00.0001.1373 (English), 03/06/2009-23:36:34, 108544 bytes
Driver: C:\WINDOWS\system32\data\cts20x.dat, 2009-06-03 23:33:10, 2091 bytes
Driver: C:\WINDOWS\system32\data\ctd20x.dat, 2009-06-03 23:33:10, 26919 bytes
Driver: C:\WINDOWS\system32\data\CTP0460W. DAT, 03/06/2009-23:36, 275836 bytes
Driver: C:\WINDOWS\system32\data\CTP0466W. DAT, 03/06/2009-23:36, 275836 bytes
Driver: C:\WINDOWS\system32\data\CTP0463W. DAT, 03/06/2009 23:36:02, 276282 bytes
Driver: C:\WINDOWS\system32\data\CTP0550W. DAT, 03/06/2009 23:36:02, 276094 bytes
Driver: C:\WINDOWS\system32\data\CTP0678W. DAT, 03/06/2009 23:36:08, 357983 bytes
Driver: C:\WINDOWS\system32\data\CTP0679W. DAT, 03/06/2009-23:36, 357983 bytes
Driver: C:\WINDOWS\system32\data\CTP0464W. DAT, 03/06/2009 23:36:02, 275836 bytes
Driver: C:\WINDOWS\system32\data\CTP0468W. DAT, 03/06/2009 23:36:02, 275836 bytes
Driver: C:\WINDOWS\system32\data\CTP0465W. DAT, 03/06/2009 23:36:02, 275836 bytes
Driver: C:\WINDOWS\system32\data\CTP0469W. DAT, 03/06/2009 23:36:02, 275836 bytes
Driver: C:\WINDOWS\system32\data\CTP0730W. DAT, 03/06/2009 23:36:04, 277688 bytes
Driver: C:\WINDOWS\system32\data\CTP0760W. DAT, 03/06/2009 23:36:04, 275257 bytes
Driver: C:\WINDOWS\system32\data\CTP046AW. DAT, 03/06/2009 23:36:04, 275508 bytes
Driver: C:\WINDOWS\system32\data\CTP046BW. DAT, 03/06/2009 23:36:04, 275508 bytes
Driver: C:\WINDOWS\system32\data\CTP046CW. DAT, 03/06/2009 23:36:04, 275508 bytes
Driver: C:\WINDOWS\system32\data\CTP0462W. DAT, 03/06/2009 23:36:06, 275836 bytes
Driver: C:\WINDOWS\system32\data\CTP055AW. DAT, 03/06/2009 23:36:04, 275766 bytes
Driver: C:\WINDOWS\system32\data\CTP073AW. DAT, 03/06/2009 23:36:06, 277688 bytes
Driver: C:\WINDOWS\system32\data\CTXFIGM. RFX, 28/07/2006 09:31:42, 41320 bytes
Driver: C:\WINDOWS\system32\data\CTXFIEM. RFX, 28/07/2006 09:31:40, 41788 bytes
Driver: C:\WINDOWS\system32\data\CTXFICM. RFX, 28/07/2006 09:31:38, 41624 bytes
Driver: C:\WINDOWS\system32\data\CTXFICBM. RFX, 23/06/2005 05:58:50, 7352 bytes
Driver: C:\WINDOWS\system32\SBXFi.ico, 2005-02-07 16:45:22, 766 bytes
Driver: C:\WINDOWS\system32\XFi.bmp, 2005-02-07 16:45:20, 3128 bytes
Driver: C:\WINDOWS\system32\ctcoinst.dll, 3.00.0002.0047 (English), 03/06/2009 23:59:44, 86016 bytes
Driver: C:\WINDOWS\system32\ctdvinst.dll, 0.05.0000.0047 (English), 03/06/2009 23:59:46, 181248 bytes
Driver: C:\WINDOWS\system32\drivers\ctdvda2k.sys, 5.13.0001.0468 (English), 04/06/2009 01:47:24, 347080 bytesName: NVIDIA GeForce 9800 GTX/9800 GTX +.
Device ID: PCI\VEN_10DE & DEV_0612 & SUBSYS_23731682 & REV_A2\4 & 243D7BD0 & 0 & 0070
Driver: c:\nvidia\displaydriver\191.07\winxp\english\NvCplSetupEng.exe, 14.00.0000.0162 (English), 2009-09-27 15:12:22, 19759424 bytes
Driver: C:\WINDOWS\system32\DRIVERS\nv4_mini.sys, 6.14.0011.9107 (in English), 2009-09-27 15:12:22, 7655872 bytes
Driver: C:\WINDOWS\system32\nv4_disp.dll, 6.14.0011.9107 (English), 2009-09-27 15:12:22, 5900416 bytes
Driver: C:\WINDOWS\system32\nvapi.dll, 6.14.0011.9107 (English), 2009-09-27 15:12:22, 888832 bytes
Driver: C:\WINDOWS\system32\nvcuda.dll, 6.14.0011.9107 (English), 2009-09-27 15:12:22, 2007040 bytes
Driver: C:\WINDOWS\system32\nvcuvenc.dll, 6.14.0011.9107 (English), 2009-09-27 15:12:22, 1714792 bytes
Driver: C:\WINDOWS\system32\nvcuvid.dll, 6.14.0011.9107 (English), 2009-09-27 15:12:22, 2194024 bytes
Driver: C:\WINDOWS\system32\nvdata.bin, 2009-09-27 15:12:22, 1604482 bytes
Driver: C:\WINDOWS\system32\nvoglnt.dll, 6.14.0011.9107 (English), 2009-09-27 15:12:22, 10756096 bytes
Driver: C:\WINDOWS\system32\nvcod.dll, 1.06.0007.0062 (English), 2009-09-27 15:12:22, 170600 bytes
Driver: C:\WINDOWS\system32\nvcodins.dll, 1.06.0007.0062 (English), 2009-09-27 15:12:22, 170600 bytesName: nForce4 HyperTransport Bridge
Device ID: PCI\VEN_10DE & DEV_005E & SUBSYS_815A1043 & REV_A3\3 & 2411E6FE & 0 & 00
Pilot: s/oName: nForce4 PCI-Express Root Port
Device ID: PCI\VEN_10DE & DEV_005D & SUBSYS_00000000 & REV_F3\3 & 2411E6FE & 0 & 68
Driver: C:\WINDOWS\system32\DRIVERS\pci.sys, 5.01.2600.5512 (English), 2008-04-13 23:06:46, 68224 bytesName: nForce4 PCI-Express Root Port
Device ID: PCI\VEN_10DE & DEV_005D & SUBSYS_00000000 & REV_F3\3 & 2411E6FE & 0 & 60
Driver: C:\WINDOWS\system32\DRIVERS\pci.sys, 5.01.2600.5512 (English), 2008-04-13 23:06:46, 68224 bytesName: nForce4 PCI-Express Root Port
Device ID: PCI\VEN_10DE & DEV_005D & SUBSYS_00000000 & REV_F3\3 & 2411E6FE & 0 & 58
Driver: C:\WINDOWS\system32\DRIVERS\pci.sys, 5.01.2600.5512 (English), 2008-04-13 23:06:46, 68224 bytesName: nForce4 PCI-Express Root Port
Device ID: PCI\VEN_10DE & DEV_005D & SUBSYS_00000000 & REV_A3\3 & 2411E6FE & 0 & 70
Driver: C:\WINDOWS\system32\DRIVERS\pci.sys, 5.01.2600.5512 (English), 2008-04-13 23:06:46, 68224 bytesName: Bridge PCI to PCI standard PCI
Device ID: PCI\VEN_10DE & DEV_005C & SUBSYS_00000000 & REV_F2\3 & 2411E6FE & 0 & 48
Driver: C:\WINDOWS\system32\DRIVERS\pci.sys, 5.01.2600.5512 (English), 2008-04-13 23:06:46, 68224 bytesName: Standard enhanced PCI to USB Host Controller
Device ID: PCI\VEN_10DE & DEV_005B & SUBSYS_815A1043 & REV_A3\3 & 2411E6FE & 0 & 11
Driver: C:\WINDOWS\system32\drivers\usbehci.sys, 5.01.2600.5512 (English), 2008-04-13 23:15:36, 30 208 bytes
Driver: C:\WINDOWS\system32\drivers\usbport.sys, 5.01.2600.5512 (English), 2008-04-13 23:15:38, 143872 bytes
Driver: C:\WINDOWS\system32\usbui.dll, 5.01.2600.5512 (English), 2008-04-14 04:51:44, 74240 bytes
Driver: C:\WINDOWS\system32\drivers\usbhub.sys, 5.01.2600.5512 (English), 2008-04-13 23:15:38, 59520 bytes
Driver: C:\WINDOWS\system32\hccoin.dll, 5.01.2600.5512 (English), 2008-04-14 04:41:56, 7168 bytesName: OpenHCD Standard USB host controller
Device ID: PCI\VEN_10DE & DEV_005A & SUBSYS_815A1043 & REV_A2\3 & 2411E6FE & 0 & 10
Pilot: C:\WINDOWS\system32\drivers\usbohci.sys, 5.01.2600.5512 (English), 2008-04-13 23:15:36, 17152 bytes
Driver: C:\WINDOWS\system32\drivers\usbport.sys, 5.01.2600.5512 (English), 2008-04-13 23:15:38, 143872 bytes
Driver: C:\WINDOWS\system32\usbui.dll, 5.01.2600.5512 (English), 2008-04-14 04:51:44, 74240 bytes
Driver: C:\WINDOWS\system32\drivers\usbhub.sys, 5.01.2600.5512 (English), 2008-04-13 23:15:38, 59520 bytesName: Multimedia Audio Controller
Device ID: PCI\VEN_10DE & DEV_0059 & SUBSYS_812A1043 & REV_A2\3 & 2411E6FE & 0 & 20
Pilot: s/oName: NVIDIA Network Bus enumerator
Device ID: PCI\VEN_10DE & DEV_0057 & SUBSYS_81411043 & REV_F3\3 & 2411E6FE & 0 & 50
Driver: C:\WINDOWS\system32\DRIVERS\nvnetbus.sys, 1.00.0000.0482 (English), 06/04/2005-03:22:30, 12928 bytes
Driver: C:\WINDOWS\system32\DRIVERS\nvnrm.sys, 1.00.0000.0482 (English), 06/04/2005-03:22:12, 261888 bytes
Driver: C:\WINDOWS\system32\DRIVERS\nvsnpu.sys, 1.00.0000.0482 (English), 06/04/2005-03:22:02, 208256 bytes
Driver: C:\WINDOWS\system32\bdco1.dll, 1.00.0000.0000 (English), 2005-04-05 14:19:20, 9728 bytes
Driver: C:\WINDOWS\system32\bdco1ins.dll, 1.00.0000.0000 (English), 06/04/2005-03:19:20, 9728 bytes
Driver: C:\WINDOWS\system32\nvconrm.dll, 1.00.0000.0017 (English), 04/04/2005 06:00:26, 32256 bytesName: NVIDIA nForce4 Serial ATA Controller
Device ID: PCI\VEN_10DE & DEV_0055 & SUBSYS_815A1043 & REV_F3\3 & 2411E6FE & 0 & 40
Driver: C:\WINDOWS\system32\DRIVERS\nvata.sys, 5.10.2600.0534 (English), 17/05/2005 17:45:08, 92800 bytes
Driver: C:\WINDOWS\system32\idecoi.dll, 1.00.0000.0001 (English), 17/05/2005 04:45:10, 300032 bytesName: NVIDIA nForce4 Serial ATA Controller
Device ID: PCI\VEN_10DE & DEV_0054 & SUBSYS_815A1043 & REV_F3\3 & 2411E6FE & 0 & 38
Driver: C:\WINDOWS\system32\DRIVERS\nvata.sys, 5.10.2600.0534 (English), 17/05/2005 17:45:08, 92800 bytes
Driver: C:\WINDOWS\system32\idecoi.dll, 1.00.0000.0001 (English), 17/05/2005 04:45:10, 300032 bytesName: NVIDIA nForce4 Parallel ATA Controller
Device ID: PCI\VEN_10DE & DEV_0053 & SUBSYS_815A1043 & REV_F2\3 & 2411E6FE & 0 & 30
Driver: C:\WINDOWS\system32\DRIVERS\nvata.sys, 5.10.2600.0534 (English), 17/05/2005 17:45:08, 92800 bytes
Driver: C:\WINDOWS\system32\idecoi.dll, 1.00.0000.0001 (English), 17/05/2005 04:45:10, 300032 bytesName: NVIDIA nForce PCI System Management
Device ID: PCI\VEN_10DE & DEV_0052 & SUBSYS_815A1043 & REV_A2\3 & 2411E6FE & 0 & 09
Pilot: s/oName: PCI standard ISA bridge
Device ID: PCI\VEN_10DE & DEV_0050 & SUBSYS_00000000 & REV_F3\3 & 2411E6FE & 0 & 08
Driver: C:\WINDOWS\system32\DRIVERS\isapnp.sys, 5.01.2600.5512 (English), 2008-04-13 23:06:42, 37248 bytesName: Silicon Image SiI 3114 SoftRAID(4) 5 Controller
Device ID: PCI\VEN_1095 & DEV_3114 & SUBSYS_81671043 & REV_02\4 & 15B9AB7D & 0 & 5048
Driver: C:\WINDOWS\system32\DRIVERS\Si3114r5.sys, 1.01.0000.0000 (English), 21/07/2004 07:02:58, 166400 bytes
Driver: C:\WINDOWS\system32\DRIVERS\SiWinAcc.sys, 1.00.0000.0008 (in English), 15/10/2003 06:28, 10240 bytes
Driver: C:\WINDOWS\system32\SilSupp.cpl, 3.00.0000.0015 (English), 11/26/2003 11:59:36, 69120 bytesName: Texas Instruments OHCI Compliant IEEE 1394 Host Controller
Device ID: PCI\VEN_104C & DEV_8023 & SUBSYS_808B1043 & REV_00\4 & 15B9AB7D & 0 & 5848
Driver: C:\WINDOWS\system32\DRIVERS\ohci1394.sys, 5.01.2600.5512 (English), 2008-04-13 23:16:20, 61696 bytes
Driver: C:\WINDOWS\system32\DRIVERS\1394bus.sys, 5.01.2600.5512 (English), 2008-04-13 23:16:20, 53376 bytes
Driver: C:\WINDOWS\system32\DRIVERS\nic1394.sys, 5.01.2600.5512 (English), 2008-04-14 04:51:44, 61824 bytes
Driver: C:\WINDOWS\system32\DRIVERS\arp1394.sys, 5.01.2600.5512 (English), 2008-04-14 04:51:44, 60800 bytes
Driver: C:\WINDOWS\system32\DRIVERS\enum1394.sys, 5.01.2600.0000 (English), 17/08/2001 08:46:40, 6400 bytesName: The standard host PCI bridge CPU
Device ID: PCI\VEN_1022 & DEV_1103 & SUBSYS_00000000 & REV_00\3 & 2411E6FE & 0 & C3
Pilot: s/oName: The standard host PCI bridge CPU
Device ID: PCI\VEN_1022 & DEV_1102 & SUBSYS_00000000 & REV_00\3 & 2411E6FE & 0 & C2
Pilot: s/oName: The standard host PCI bridge CPU
Device ID: PCI\VEN_1022 & DEV_1101 & SUBSYS_00000000 & REV_00\3 & 2411E6FE & 0 & C1
Pilot: s/oName: The standard host PCI bridge CPU
Device ID: PCI\VEN_1022 & DEV_1100 & SUBSYS_00000000 & REV_00\3 & 2411E6FE & 0 & C0
Pilot: s/o------------------
DirectX components
------------------
Ddraw.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:52 279552 bytes
ddrawex.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:52 27136 bytes
dxapi.sys: 5.01.2600.0000 English Final Retail 08/23/2001 07:00 10496 bytes
D3D8.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:52 1179648 bytes
d3d8thk.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:52 8192 bytes
D3D9.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:52 1689088 bytes
D3dim.dll: 5.01.2600.0000 English Final Retail 08/23/2001 07:00 436224 bytes
d3dim700.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:52 824320 bytes
d3dramp.dll: 5.01.2600.0000 English Final Retail 08/23/2001 07:00 590336 bytes
d3drm.dll: 5.01.2600.0000 English Final Retail 08/23/2001 07:00 350208 bytes
d3dxof.dll: 5.01.2600.0000 English Final Retail 08/23/2001 07:00 47616 bytes
d3dpmesh.dll: 5.01.2600.0000 English Final Retail 08/23/2001 07:00 34816 bytes
dplay.dll: 5.00.2134.0001 English Final Retail 08/23/2001 07:00 33040 bytes
dplayx.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 229888 bytes
dpmodemx.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 23552 bytes
dpwsock.dll: 5.00.2134.0001 English Final Retail 08/23/2001 07:00 42768 bytes
dpwsockx.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54, 57344 bytes
dplaysvr.exe: 5.03.2600.5512 English retail Final 14/04/2008 04:42:18 29696 bytes
dpnsvr.exe: 5.03.2600.5512 English retail Final 14/04/2008 04:42:18 17920 bytes
dpnet.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 375296 bytes
dpnlobby.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:39:22 3072 bytes
dpnaddr.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:39:20 3072 bytes
dpvoice.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 212480 bytes
DPVSetup.exe: 5.03.2600.5512 English retail Final 14/04/2008 04:42:20 83456 bytes
dpvvox.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 116736 bytes
dpvacm.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 21504 bytes
dpnhpast.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 35328 bytes
dpnhupnp.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 60928 bytes
dpserial.dll: 5.00.2134.0001 English Final Retail 08/23/2001 07:00 53520 bytes
Dinput.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 158720 bytes
Dinput8.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 181760 bytes
dimap.dll: 5.01.2600.0000 English Final Retail 08/23/2001 07:00 44032 bytes
diactfrm.dll: 5.01.2600.0000 English Final Retail 08/23/2001 07:00 394240 bytes
Joy.cpl: 5.03.2600.5512 English retail Final 14/04/2008 04:42:42 68608 bytes
gcdef.dll: 5.01.2600.0000 English Final Retail 08/23/2001 07:00 76800 bytes (problem)
PID.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:51:44 35328 bytes
gameenum.sys: 5.01.2600.5512 English retail Final 13/04/2008 23:15:30 10624 bytes
Dsound.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 367616 bytes
dsound3d.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 bytes 1293824
dswave.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 19456 bytes
dsdmo.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 181248 bytes
dsdmoprp.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 71680 bytes
dmusic.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 104448 bytes
dmband.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 28672 bytes
dmcompos.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 61440 bytes
dmime.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 181248 bytes
dmloader.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 35840 bytes
dmstyle.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 105984 bytes
dmsynth.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 103424 bytes
DMScript.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 82432 bytes
Microsoft.DirectX.Direct3D.dll: 9.05.0132.0000 English retail Final 30/07/2009 23:05:29 473600 bytes
Microsoft.DirectX.Direct3DX.dll: 5.04.0000.3900 English retail Final 30/07/2009 23:05:21 2676224 bytes
Microsoft.DirectX.Direct3DX.dll: 9.04.0091.0000 English retail Final 30/07/2009 23:05:22 bytes 2846720
Microsoft.DirectX.Direct3DX.dll: 9.05.0132.0000 English retail Final 30/07/2009 23:05:23 563712 bytes
Microsoft.DirectX.Direct3DX.dll: 9.06.0168.0000 English retail Final 30/07/2009 23:05:23 567296 bytes
Microsoft.DirectX.Direct3DX.dll: 9.07.0239.0000 English retail Final 30/07/2009 23:05:23 576000 bytes
Microsoft.DirectX.Direct3DX.dll: 9.08.0299.0000 English retail Final 30/07/2009 23:05:24 577024 bytes
Microsoft.DirectX.Direct3DX.dll: 9.09.0376.0000 English retail Final 30/07/2009 23:05:24 577536 bytes
Microsoft.DirectX.Direct3DX.dll: 9.10.0455.0000 English retail Final 30/07/2009 23:05:24 577536 bytes
Microsoft.DirectX.Direct3DX.dll: 9.11.0519.0000 English retail Final 30/07/2009 23:05:25 578560 bytes
Microsoft.DirectX.Direct3DX.dll: 9.12.0589.0000 English retail Final 30/07/2009 23:05:29 578560 bytes
Microsoft.DirectX.DirectDraw.dll: 5.04.0000.2904 English retail Final 30/07/2009 23:05:30 145920 bytes
Microsoft.DirectX.DirectInput.dll: 5.04.0000.2904 English retail Final 30/07/2009 23:05:30 159232 bytes
Microsoft.DirectX.DirectPlay.dll: 5.04.0000.2904 English retail Final 30/07/2009 23:05:30 364544 bytes
Microsoft.DirectX.DirectSound.dll: 5.04.0000.2904 English retail Final 30/07/2009 23:05:30 178176 bytes
Microsoft.DirectX.AudioVideoPlayback.dll: 5.04.0000.2904 English retail Final 30/07/2009 23:05:25 53248 bytes
Microsoft.DirectX.Diagnostics.dll: 5.04.0000.2904 English retail Final 30/07/2009 23:05:29 12800 bytes
Microsoft.DirectX.dll: 5.04.0000.2904 English retail Final 30/07/2009 23:05:25 223232 bytes
dx7vb.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 bytes 619008
dx8vb.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 bytes 1227264
c:\windows\system32\dxdiagn.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 bytes 2113536
MFC40.dll: 4.01.0000.6140 English retail Final 23/08/2001 07:00 924432 bytes
Mfc42.dll: 6.02.4131.0000 English retail Final 14/04/2008 04:41:58 1028096 bytes
Wsock32.dll: 5.01.2600.5512 English retail Final 14/04/2008 04:42:12 22528 bytes
amstream.dll: 6.05.2600.5512 English retail Final 14/04/2008 04:41:50 70656 bytes
devenum.dll: 6.05.2600.5512 English retail Final 14/04/2008 04:41:52 59904 bytes
Dxmasf.dll: 6.04.0009.1133 English retail Final 14/04/2008 04:41:54 bytes 498742
mciqtz32.dll: 6.05.2600.5512 English retail Final 14/04/2008 04:41:58 35328 bytes
mpg2splt.AX: 6.05.2600.5512 English retail Final 14/04/2008 04:42:44 148992 bytes
msdmo.dll: 6.05.2600.5512 English Final 14/04/2008 detail 04:42 14336 bytes
encapi.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:54 20480 bytes
QASF.dll: 11.00.5721.5145 English retail Final 18/10/2006 20:47:18 211456 bytes
QCAP.dll: 6.05.2600.5512 English retail Final 14/04/2008 04:42:04 192512 bytes
QDV.dll: 6.05.2600.5512 English retail Final 14/04/2008 04:42:04 279040 bytes
Qdvd.dll: 6.05.2600.5512 English retail Final 14/04/2008 04:42:04 386048 bytes
Qedit.dll: 6.05.2600.5512 English retail Final 14/04/2008 04:42:04 562176 bytes
qedwipes.dll: 6.05.2600.5512 English retail Final 13/04/2008 21:51:34 733696 bytes
Quartz.dll: 6.05.2600.5822 English retail Final 03/06/2009 14:09:37 1291264 bytes
Strmdll.dll: 4.01.0000.3938 English retail Final 26/08/2009 03:00:21 247326 bytes
iac25_32.AX: 2.00.0005.0053 English retail Final 14/04/2008 04:42:44 199680 bytes
ir41_32.AX: 4.51.0016.0003 English retail Final 14/04/2008 04:42:44 bytes 848384
ir41_qc.dll: 4.30.0062.0002 English retail Final 14/04/2008 04:41:56 bytes, 120320
ir41_qcx.dll: 4.30.0064.0001 English retail Final 14/04/2008 04:41:56 bytes 338432
ir50_32.dll: 5.2562.0015.0055 English retail Final 14/04/2008 04:41:56 755200 bytes
ir50_qc.dll: 5.00.0063.0048 English retail Final 14/04/2008 04:41:56 200192 bytes
ir50_qcx.dll: 5.00.0064.0048 English retail Final 14/04/2008 04:41:56 183808 bytes
ivfsrc.AX: 5.10.0002.0051 English retail Final 14/04/2008 04:42:44 154624 bytes
mswebdvd.dll: 6.05.2600.5857 English retail Final 05/08/2009 04:01:48 204800 bytes
The KS.sys: 5.03.2600.5512 English retail Final 13/04/2008 23:46:38, 141056 bytes
ksproxy.AX: 5.03.2600.5512 English retail Final 14/04/2008 04:42:44 129536 bytes
ksuser.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:41:58 4 096 bytes
Stream.sys: 5.03.2600.5512 English retail Final 13/04/2008 23:15:16 49408 bytes
MSPCLOCK.sys: 5.03.2600.5512 English retail Final 14/04/2008 04:51:44 5376 bytes
MSPQM.sys: 5.01.2600.5512 English retail Final 14/04/2008 04:51:44 4992 bytes
MSKSSRV.sys: 5.03.2600.5512 English retail Final 14/04/2008 04:51:44 7552 bytes
SWENUM.sys: 5.03.2600.5512 English retail Final 14/04/2008 04:51:44 4352 bytes
MSTEE.sys: 5.03.2600.5512 English retail Final 13/04/2008 23:09:52 5504 bytes
bdaplgin.AX: 5.03.2600.5512 English retail Final 14/04/2008 04:51:44 18432 bytes
bdasup.sys: 5.03.2600.5512 English retail Final 14/04/2008 04:51:44 11776 bytes
msdvbnp.AX: 6.05.2600.5512 English retail Final 14/04/2008 04:51:44 56832 bytes
Psisdecd.dll: 6.05.2600.5512 English retail Final 14/04/2008 04:51:44 bytes 363520
psisrndr.AX: 6.05.2600.5512 English retail Final 14/04/2008 04:51:44 33280 bytes
ipsink.AX: 5.03.2600.5512 English retail Final 14/04/2008 04:51:44 16384 bytes
mpeg2data.AX: 6.05.2600.5512 English retail Final 14/04/2008 04:42:44 118272 bytes
NdisIP.sys: 5.03.2600.5512 English retail Final 14/04/2008 04:51:44 bytes 10880
MPE.sys: 5.03.2600.5512 English retail Final 14/04/2008 04:51:44 15232 bytes
C:\windows\system32\drivers\streamip.sys: 5.03.2600.5512 English retail Final 13/04/2008 23:16:22 15232 bytes
MSVidCtl.dll: 6.05.2600.5512 English retail Final 14/04/2008 04:42:02, 1428992 bytes
Slip.sys: 5.03.2600.5512 English retail Final 13/04/2008 23:16:24 11136 bytes
C:\windows\system32\drivers\nabtsfec.sys: 5.03.2600.5512 English retail Final 13/04/2008 23:16:26 85248 bytes
C:\windows\system32\drivers\ccdecode.sys: 5.03.2600.5512 English retail Final 13/04/2008 23:16:24 17024 bytes
vbisurf.AX: 5.03.2600.5512 English retail Final 14/04/2008 04:42:44 30 208 bytes
msyuv.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:51:44 16896 bytes
Kstvtune.AX: 5.03.2600.5512 English retail Final 14/04/2008 04:42:44 61952 bytes
ksxbar.AX: 5.03.2600.5512 English retail Final 14/04/2008 04:42:44 43008 bytes
Kswdmcap.AX: 5.03.2600.5512 English retail Final 14/04/2008 04:42:44 91136 bytes
WSTCODEC.sys: 5.03.2600.5512 English retail Final 13/04/2008 23:16:26 19200 bytes
wstdecod.dll: 5.03.2600.5512 English retail Final 14/04/2008 04:42:12 50688 bytes
MSDV.sys: 5.03.2600.5512 English retail Final 13/04/2008 23:16:10 51200 bytes------------------
DirectShow filters
------------------DirectShow filters:
WMAudio Decoder DMO, 0 x 00800800, 1, 1,
WMAPro over S/PDIF DMO, 0 x 00600800, 1, 1,
WMA Voice DMO decoder, 0 x 00600800, 1, 1,
Mpeg4s Decoder DMO, 0 x 00800001, 1, 1,
Decoder DMO, 0 x 00800001, 1, 1 screen, WMV
WMVideo Decoder DMO, 0 x 00800001, 1, 1,
Mpeg43 Decoder DMO, 0 x 00800001, 1, 1,
MPEG4 Decoder DMO, 0 x 00800001, 1, 1,
WMT MuxDeMux Filter, 0 x 00200000, 0, 0, wmm2filt.dll, 2.01.4026.0000
Full-screen Renderer, 00200000 x 0, 1, 0, quartz.dll, 6.05.2600.5822
Upsample CT filter, 0 x 00100000, 1, 1, Upsample.ax, 2.00.0005.0000
Writer, 00200000 x 0, 1, 0, WavWrite.ax, 3.01.0004.0000 creative wave
DV Muxer, 0x00400000, 0, 0, qdv.dll, 6.05.2600.5512
Converter, 0 x 00400001, 1, 1, quartz.dll, 6.05.2600.5822 color space
Reader, 0x00400000, 0, 0, qasf.dll, WM ASF 11.00.5721.5145
Filter, 0 x 00200000, 0, 1, wmpsrcwp.dll, 11.00.5721.5145 screenshot
AVI Splitter, 0 x 00600000, 1, 1, quartz.dll, 6.05.2600.5822
AudioAnalyzer, 0 x 00200000, 1, 1, wmm2filt.dll, 2.01.4026.0000 WMT
VGA 16 color Ditherer, 0 x 00400000, 1, 1, quartz.dll, 6.05.2600.5822
Indeo® video 5.10 Compression Filter, 0 x 00200000, 1, 1, ir50_32.dll, 5.2562.0015.0055
Metadata, 0x001fffff, 1, 1, MetaBPMu.ax, 2.00.0002.0000 BPM
Windows Media Audio Decoder, 0 x 00800001, 1, 1, msadds32.ax, 8.00.0000.4487
Creative Recording Wav_Asio Filter, 0 x 00400000, 0, 1, AudioRec.ax, 1.00.0002.0000
AC3 parser Filter, 0 x 00600000, 1, 1, mpg2splt.ax, 6.05.2600.5512
WMT Format Conversion, 0 x 00200000, 1, 1, wmm2filt.dll, 2.01.4026.0000
Time scale filter, 0 x 00100000, 1, 1 CT, TimeScal.ax, 2.03.0009.0000
StreamBufferSink, 0 x 00200000, 0, 0, sbe.dll, 6.05.2600.5512
WMT frame black Generator, 0 x 00200000, 1, 1, wmm2filt.dll, 2.01.4026.0000
MJPEG Decompressor, 0 x 00600000, 1, 1, quartz.dll, 6.05.2600.5822
Indeo® video 5.10 Decompression Filter, 0 x 00640000, 1, 1, ir50_32.dll, 5.2562.0015.0055
Capture screen filter, 0 x 00200000 WMT, 0, 1, wmm2filt.dll, 2.01.4026.0000
Microsoft screen video Decompressor, 0 x 00800000, 1, 1, msscds32.ax, 8.00.0000.4487
MPEG-I Stream Splitter, 0 x 00600000, 1, 2, quartz.dll, 6.05.2600.5822
Parser, 0 x 00400000, 1, 1, quartz.dll, 6.05.2600.5822 SAMI (CC)
MPEG Layer - 3 Decoder, 0 x 00810000, 1, 1, l3codecx.ax, 1.05.0000.0050
MPEG-2 Splitter, 0x005fffff, 1, 0, mpg2splt.ax, 6.05.2600.5512
ACELP.net Sipro Lab Audio Decoder, 0 00800001, 1, 1, x acelpdec.ax, 1.04.0000.0000
Photo Story 3 Source Filter, 0x00000000, 0, 0,
Renderer, 0 x 00800001, 1, 0, quartz.dll, 6.05.2600.5822 Script command internal
MPEG Audio Decoder, 0 x 03680001, 1, 1, quartz.dll, 6.05.2600.5822
File Source (Netshow URL), 0 x 00400000, 0, 1, wmpasf.dll, 11.00.5721.5145
WMT Import Filter, 0 x 00200000, 0, 1, wmm2filt.dll, 2.01.4026.0000
DV Splitter, 0 x 00600000, 1, 2, qdv.dll, 6.05.2600.5512
Generate, 0 x 00200000, 1, 1 bitmap, image wmm2filt.dll, 2.01.4026.0000
Windows Media video Decoder, 0 x 00800000, 1, 1, wmvds32.ax, 8.00.0000.4487
Video Mixing Renderer 9 0 x 00200000, 1, 0, quartz.dll, 6.05.2600.5822
Windows Media video Decoder, 0 x 00800000, 1, 1, wmv8ds32.ax, 8.00.0000.4000
WMT 2 Fix, 0 x 00200000, 1, 1, wmm2filt.dll, 2.01.4026.0000
Note tail, 0 x 00200000, 1, 1, wmm2filt.dll, 2.01.4026.0000
Filter, 0 x 00100000, 1, 1, Karaoke.ax, 2.00.0012.0000 CT Karaoke
Filter, 0 x 00400000, 0, 1, AC3Srcu.ax, 3.02.0001.0000 Source creative AC3
Writer, 00200000 x 0, 1, 0, RawWritu.ax, 1.00.0000.0000 Raw PCM creative
Windows Media multiplex, 0 x 00600000, 1, 1, wmpasf.dll, 11.00.5721.5145
ASX Parser file, 0 x 00600000, 1, 1, wmpasf.dll, 11.00.5721.5145
File v.2 ASX Parser, 0 x 00600000, 1, 0, wmpasf.dll, 11.00.5721.5145
File NSC Parser, 0 x 00600000, 1, 1, wmpasf.dll, 11.00.5721.5145
PDP CT filter, 0 x 00100000, 1, 1, PDP.ax, 1.00.0008.0000
ACM Wrapper, 0 x 00600000, 1, 1, quartz.dll, 6.05.2600.5822
Windows Media source filter, 0 x 00600000, 0, 2, wmpasf.dll, 11.00.5721.5145
Video Renderer, 0 x 00800001, 1, 0, quartz.dll, 6.05.2600.5822
Frame Eater, 0 00200000, 1, 1, x wmm2filt.dll, 2.01.4026.0000
Video stream MPEG - 2 Analyzer, 0 x 00200000, 0, 0, sbe.dll, 6.05.2600.5512
Line 21 Decoder, 0 x 00600000, 1, 1, qdvd.dll, 6.05.2600.5512
Port video Manager, 0 x 00600000, 2, 1, quartz.dll, 6.05.2600.5822
Decoder, 0 x 00600000, 1, 1, wstdecod.dll, 5.03.2600.5512 WST
Video Renderer, 0x00400000, 1, 0, quartz.dll, 6.05.2600.5822
Decoder DivX Filter, 0xff800000, 1, 1, divxdec.ax, 6.03.0000.0085
CT SmartVolumeManagement filter, 0 x 00100000, 1, 1, DSCompr.ax, 1.00.0008.0000
Filter, 0 x 00200000, 1, 1, AudGain.ax, 1.00.0000.0000 Gain Audio creative
Writer, 0x00400000, 0, 0, qasf.dll, WM ASF 11.00.5721.5145
WMT sample information Filter, 0 x 00200000, 1, 1, wmm2filt.dll, 2.01.4026.0000
Allocator, 0 x 00600000, 1, 1, vbisurf.ax, 5.03.2600.5512 Surface of VBI
Microsoft MPEG-4 video Decompressor, 0 x 00800000, 1, 1, mpg4ds32.ax, 8.00.0000.4487
Filter, 0 x 00400000, 0, 1, FlacSrcu.ax, 1.00.0002.0000 of the creative Source of Flac
DivX Demux, 0 x 00600000, 1, 0, DivXMedia.ax, 0.00.0000.0028
File writer, 00200000 x 0, 1, 0, qcap.dll, 6.05.2600.5512
MLP Creative Source Filter, 0 x 00400000, 0, 1, MlpSrcu.ax, 3.01.0000.0000
Creating file reader Filter, 0 x 00400000, 0, 1, FilReadu.ax, 1.00.0005.0000
Metadata, 0x001fffff, 1, 1, MetaSVMu.ax, 2.00.0002.0000 SVM
CT HPVirtualizer filter, 0 x 00100000, 1, 1, Virtual.ax, 1.00.0000.0000
WMT Log Filter, 0 x 00200000, 1, 1, wmm2filt.dll, 2.01.4026.0000
WMT Renderer, 00200000 x 0, 1, 0, wmm2filt.dll, 2.01.4026.0000 virtual
DVD Navigator, 0 x 00200000, 0, 2, qdvd.dll, 6.05.2600.5512
Mixer2, 0 x 00400000, 1, 1, qdvd.dll, 6.05.2600.5512 overlay
CT CMSS3 filter, 0 x 00100000, 1, 1, CMSS3.ax, 3.00.0013.0000
AVI Draw, 0 x 00600064, 9, 1, quartz.dll, 6.05.2600.5822
. File Parser RAM, 0 x 00600000, 1, 0, wmpasf.dll, 11.00.5721.5145
WMT DirectX Transform Wrapper, 0 x 00200000, 1, 1, wmm2filt.dll, 2.01.4026.0000
G.711 Codec, 0 x 00200000, 1, 1, g711codc.ax, 5.01.2600.0000
MPEG2 demux, 0 x 00600000, 1, 1, mpg2splt.ax, 6.05.2600.5512
Filter, 0 x 00400000, 0, 1, OggSrcu.ax, the creative Source of Ogg 1.00.0001.0000
Decoder, 0 x 00800000, 1, 1, qdv.dll, 6.05.2600.5512 DV video
NVF Creative Filter, 0 x 00400000, 0, 1, NvfSrcu.ax, 3.01.0001.0000
Indeo® audio software, 0 x 00500000, 1, 1, iac25_32.ax, 2.00.0005.0053
Update Windows Media Filter, 0 x 00400000, 1, 0, wmpasf.dll, 11.00.5721.5145
Noise Reduction, 00100000, 1, 1, x 0 NoisRedu.ax, 3.00.0007.0000
Handler, 0 x 00600000, 1, 1, wmpasf.dll, 11.00.5721.5145 ASF DIB
ASF ACM Handler, 0 x 00600000, 1, 1, wmpasf.dll, 11.00.5721.5145
ASF ICM Handler, 0 x 00600000, 1, 1, wmpasf.dll, 11.00.5721.5145
ASF URL Handler, 0 x 00600000, 1, 1, wmpasf.dll, 11.00.5721.5145
Handler, 0 x 00600000, 1, 1, wmpasf.dll, 11.00.5721.5145 ASF JPEG
IMAGES of the ASF Handler, 0 x 00600000, 1, 1, wmpasf.dll, 11.00.5721.5145
ASF embedded stuff Handler, 0 x 00600000, 1, 1, wmpasf.dll, 11.00.5721.5145
DivX Subtitle Decoder, 0 x 00600000, 1, 1, DivXMedia.ax, 0.00.0000.0028
9x8Resize, 0 x 00200000, 1, 1, wmm2filt.dll, 2.01.4026.0000
WIA instant flow Filter, 0 x 00200000, 1, 1, wiasf.ax, 1.00.0000.0000
0 00200000, 1, 1, x, allocator Fix wmm2filt.dll, 2.01.4026.0000
SampleGrabber, 0 x 00200000, 1, 1, qedit.dll, 6.05.2600.5512
Renderer, 00200000 x 0, 1, 0, qedit.dll, 6.05.2600.5512 null
Creative Writer, 0 x 00200000 WMA, 1, 0, WMAWrite.ax, 5.00.0001.0000
WMT Source, 0 x 00200000, 0, 1, wmm2filt.dll, 2.01.4026.0000 virtual
Filter, 0 x 00600000, 0, 1, ivfsrc.ax, 5.10.0002.0051 source of IVF
Interlacer, 0 00200000, 1, 1, x wmm2filt.dll, 2.01.4026.0000 WMT
StreamBufferSource, 0 x 00200000, 0, 0, sbe.dll, 6.05.2600.5512
Smart Tee, 0 x 00200000, 1, 2, qcap.dll, 6.05.2600.5512
WMA Creative Source Filter, 0 x 00400000, 0, 1, WmaSrc.ax, 3.01.0001.0000
Mix, 0 x 00200000, 0, 0, qdvd.dll, 6.05.2600.5512 overlay
AVI Decompressor, 0 x 00600000, 1, 1, quartz.dll, 6.05.2600.5822
Domain uncompressed detection Filter, 0 x 00200000 shooting, 1, 1, wmm2filt.dll, 2.01.4026.0000
Source, 0 x 00400000, 0, 2, quartz.dll, 6.05.2600.5822 AVI/WAV file
QuickTime Movie Parser, 0 x 00600000, 1, 1, quartz.dll, 6.05.2600.5822
Parser, 0 x 00400000, 1, 1, quartz.dll, 6.05.2600.5822 wave
Parser, 0 x 00400000, 1, 1, quartz.dll, 6.05.2600.5822 noon
Multi-fichier Parser, 0 x 00400000, 1, 1, quartz.dll, 6.05.2600.5822
File stream renderer, 0x00400000, 1, 1, quartz.dll, 6.05.2600.5822
XML Playlist, 0x00400000, 1, 0, wmpasf.dll, 11.00.5721.5145
AVI Mux, 00200000 x 0, 1, 0, qcap.dll, 6.05.2600.5512
Line 21 decoder 2, 0 x 00600002, 1, 1, quartz.dll, 6.05.2600.5822
File Source (Async.), 0 x 00400000, 0, 1, quartz.dll, 6.05.2600.5822
File Source (URL), 0 x 00400000, 0, 1, quartz.dll, 6.05.2600.5822
WMT DV Extract, 0 x 00200000, 1, 1, wmm2filt.dll, 2.01.4026.0000
CDDA Creative Source Filter, 0 x 00400000, 0, 1, CDDA.ax, 3.00.0003.0000
Creative LiveRecording filter SxS, 0 x 00400000, 0, 1, LiveRecu.ax, 5.00.0001.0000
WAV Dest, 0 x 00000000, 0, 0,
Filter, 0 x 00200000, 1, 1, wmm2filt.dll, 2.01.4026.0000 switch WMT
Volume, 0 x 00200000, 1, 1, wmm2filt.dll, 2.01.4026.0000 WMT
Filter, 0 x 00400000, 0, 1, InetSrcu.ax, 1.00.0000.0000 creative Internet Source
Video, 0 x 00200000, 1, 1, wmm2filt.dll, Extensible 2.01.4026.0000
Infinite pin Tee Filter, 0 x 00200000, 1, 1, qcap.dll, 6.05.2600.5512
Decompressor, 0 x 00600000, 1, 1, quartz.dll, 6.05.2600.5822 QT
Decoder, 0 x 40000001, 1, 1, quartz.dll, 6.05.2600.5822 MPEG video
Indeo® video 4.4 Decompression Filter, 0 x 00640000, 1, 1, ir41_32.ax, 4.51.0016.0003
Indeo® video 4.4 Compression Filter, 0 x 00200000, 1, 1, ir41_32.ax, 4.51.0016.0003WDM streaming data transformations:
Cancellation of acoustic echo of core Microsoft, 0 x 00000000, 0, 0,
Core Microsoft GS Wavetable Synthesizer, 0 x 00200000, 1, 1, 5.03.2600.5512
Microsoft Kernel DLS, 0 x 00200000, 1, 1, 5.03.2600.5512 synthesizer
Audio decoder core Microsoft DRM, 0 x 00200000, 1, 1, 5.03.2600.5512Video compressors:
WMVideo8 encoder DMO, 0 x 00600800, 1, 1,
MSScreen encoder DMO, 0 x 00600800, 1, 1,
WMVideo9 encoder DMO, 0 x 00600800, 1, 1,
Encoder DMO MSScreen 9, 0 x 00600800, 1, 1,
Encode, 0 x 00200000, 0, 0, qdv.dll, 6.05.2600.5512 DV video
Indeo® video 5.10 Compression Filter, 0 x 00100000, 1, 1, ir50_32.dll, 5.2562.0015.0055
MJPEG Compressor, 0 x 00200000, 0, 0, quartz.dll, 6.05.2600.5822
Cinepak Codec by Radius, 0 x 00200000, 1, 1, qcap.dll, 6.05.2600.5512
Codec DivX 6.8.5 (CPUs), 0 x 00200000, 1, 1, qcap.dll, 6.05.2600.5512 logic 2
Intel 4:2:0 video V2.50, 0 x 00200000, 1, 1, qcap.dll, 6.05.2600.5512
Intel Indeo video A3.2, 0 x 00200000, 1, 1, qcap.dll, 6.05.2600.5512
Intel Indeo® video 4.5, 0 x 00200000, 1, 1, qcap.dll, 6.05.2600.5512
Indeo® video 5.10, 0 x 00200000, 1, 1, qcap.dll, 6.05.2600.5512
Intel IYUV codec, 0 x 00200000, 1, 1, qcap.dll, 6.05.2600.5512
Codec, 0 x 00200000, 1, 1, qcap.dll, 6.05.2600.5512 Microsoft H.261 video
Codec, 0 x 00200000, 1, 1, qcap.dll, 6.05.2600.5512 Microsoft H.263 video
Microsoft RLE, 0 x 00200000, 1, 1, qcap.dll, 6.05.2600.5512
Microsoft Video 1, 0 x 00200000, 1, 1, qcap.dll, 6.05.2600.5512
Codec, 0 x 00200000, 1, 1, qcap.dll, 6.05.2600.5512 Xfire video
DivX 6.8.5 YV12 Decoder, 0 x 00200000, 1, 1, qcap.dll, 6.05.2600.5512Audio compressors:
Encoder WMA Voice DMO, 0 x 00600800, 1, 1,
Speech WM Encoder DMO, 0 x 00600800, 1, 1,
WMAudio encoder DMO, 0 x 00600800, 1, 1,
IAC2, 0 x 00200000, 1, 1, quartz.dll, 6.05.2600.5822
4.8kbit/s,0x00200000,1,1,Quartz.dll,6.05.2600.5822 Lernout & languages CELP
Lernout & languages SBC 8kbit/s,0x00200000,1,1,quartz.dll,6.05.2600.5822
Lernout & languages SBC 12kbit/s,0x00200000,1,1,quartz.dll,6.05.2600.5822
Lernout & languages SBC 16kbit/s,0x00200000,1,1,quartz.dll,6.05.2600.5822
IMA ADPCM, 0 x 00200000, 1, 1, quartz.dll, 6.05.2600.5822
PCM, 0 x 00200000, 1, 1, quartz.dll, 6.05.2600.5822
Microsoft ADPCM, 0 x 00200000, 1, 1, quartz.dll, 6.05.2600.5822
ACELP.net, 0 x 00200000, 1, 1, quartz.dll, 6.05.2600.5822
DSP Group TrueSpeech (TM), 0 x 00200000, 1, 1, quartz.dll, 6.05.2600.5822
Windows Media Audio V1, 0 x 00200000, 1, 1, quartz.dll, 6.05.2600.5822
Windows Media Audio V2, 0 x 00200000, 1, 1, quartz.dll, 6.05.2600.5822
GSM 6.10, 0 x 00200000, 1, 1, quartz.dll, 6.05.2600.5822
Messenger Audio Codec, 0 x 00200000, 1, 1, quartz.dll, 6.05.2600.5822
Microsoft G.723.1, 0 x 00200000, 1, 1, quartz.dll, 6.05.2600.5822
CCITT A - Law, 0 x 00200000, 1, 1, quartz.dll, 6.05.2600.5822
CCITT u - Law, 0 x 00200000, 1, 1, quartz.dll, 6.05.2600.5822
MPEG Layer-3, 0 x 00200000, 1, 1, quartz.dll, 6.05.2600.5822Audio Capture sources:
SB X - Fi Audio [8000], 0 x 00200000, 0, 0, qcap.dll, 6.05.2600.5512
AK5370, 0 x 00200000, 0, 0, qcap.dll, 6.05.2600.5512Midi converters:
Default MidiOut Device, 0 x 00800000, 1, 0, quartz.dll, 6.05.2600.5822
Microsoft GS Wavetable SW Synth, 00200000 x 0, 1, 0, quartz.dll, 6.05.2600.5822
MPU-401, 0 x 00200000, 1, 0, quartz.dll, 6.05.2600.5822
SB X - Fi Synth a [8000], 0 x 00200000, 1, 0, quartz.dll, 6.05.2600.5822
SB X - Fi Synth B [8000], 0 x 00200000, 1, 0, quartz.dll, 6.05.2600.5822WDM Streaming Capture devices:
0 x 00000000, 0, 0,
SB X - Fi Audio [8000], 0 x 00200000, 3, 2, 5.03.2600.5512
Audio USB, 0 x 00200000, 1, 1, 5.03.2600.5512WDM Streaming making devices:
0 x 00000000, 0, 0,
SB X - Fi DMusic synthesizer [8000], 0 x 00200000, 1, 1, 5.03.2600.5512
SB X - Fi Synth has [8000], 0 x 00200000, 1, 1, 5.03.2600.5512
SB X - Fi Synth B [8000], 0 x 00200000, 1, 1, 5.03.2600.5512
SB X - Fi Audio [8000], 0 x 00200000, 3, 2, 5.03.2600.5512WDM Streaming Mixer devices:
Mixer Audio Wave of core Microsoft, 0 x 00000000, 0, 0,CP/CA BDA filters:
Decrypt/Tag,0x00600000,1,0,encdec.dll,6.05.2600.5512
Encrypt/Tag,0x00200000,0,0,encdec.dll,6.05.2600.5512
XDS Codec, 0 x 00200000, 0, 0, encdec.dll, 6.05.2600.5512Audio converters:
SB X - Fi Audio [8000], 0 x 00200000, 1, 0, quartz.dll, 6.05.2600.5822
DirectSound Device, 0 x 00800000, 1, 0, quartz.dll, default 6.05.2600.5822
Default WaveOut Device, 0 x 00200000, 1, 0, quartz.dll, 6.05.2600.5822
DirectSound: SB X - Fi Audio [8000], 0 x 00200000, 1, 0, quartz.dll, 6.05.2600.5822WDM Streaming features:
MPU - 401, 0 X 00200000, 1, 1, 5.03.2600.5512
SB X - Fi DMusic synthesizer [8000], 0 x 00200000, 7, 2, 5.03.2600.5512
SB X - Fi Synth has [8000], 0 x 00200000, 1, 1, 5.03.2600.5512
SB X - Fi Synth B [8000], 0 x 00200000, 9, 2, 5.03.2600.5512
SB X - Fi Audio [8000], 0 x 00200000, 9, 2, 5.03.2600.5512
Audio USB, 0 x 00200000, 1, 1, 5.03.2600.5512Hi Snowpy24,
Welcome to the Microsoft Answers site.
Method 1:
Download the DirectX from the Microsoft Web site and then try to install it on the system. Click on the link below.
Use DirectX Runtimes (August 2009)
Method 2:
I suggest you try a SFC scan. Follow the steps to perform a scan of the SFC.
1. click on the Start button
2. on the Start Menu, click all programs followed by accessories
3. in the menu accessories, right-click on command line option
4. in the menu that appears, click on the option "Run as Administrator"
5. If you have the User Account Control (UAC) enabled, you will be asked permission before the opening of the command line. You simply press the button continue if you are the administrator or insert password etc.
6. in the command prompt window, type: sfc/scannow , and then press enter
7. a message will appear stating that "the system of scanning will start"
8. be patient because the analysis may take some time
9. If all the files need replace SFC will replace them. You may be asked to insert your XP CD for this process to continue
10. If all goes although you should, after the analysis, see the following message "Windows resource protection not found any breach of integrity.
11. once the scan is finished, close the command prompt window, restart the computer and check.
For more details, see the article mentioned below.
Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe)
http://support.Microsoft.com/kb/310747
Hope this information is useful.
Thanks and regards.
Thahaseena M
Microsoft Answers Support Engineer.
Visit our Microsoft answers feedback Forum and let us know what you think. -
I am using Microsoft Windows XP Professional, version 2002, Service Pack 3.
I recently reinstalled my operating system on my Dell Dimension 2400 PC and allowed for automatic updates. Previously I did not allow updates. I use very slow dial-up on a BCM 56 k
Voice/Fax/Modem. My previous connection was about 26 Kbps.
During updates of Windows XP, Microsoft notified me of the update following software:
(Broadcom Corporation - Modems - BCM. v92 56 k Modem, size: 2.8 MB, Broadcom Corporation modem software update published on August 27, 2003.) only the Microsoft Update downloaded and installed on my PC.
After the installation of update BCM, my modem went much more quickly in about 40 Kbps, however, I lost the Unimodem half-duplex audio driver configuration.
After the automatic BCM update, my modem sounds is the audio connection as he had done before.
I checked and the following driver files still exist where they belong: [C:\Windows\system32\drivers\ks.sys; C:\Windows\system32\DRIVERS\MODEMCSA.sys; C:\Windows\system32\ksproxy.AX; C:\Windows\system32\kuser.dll], however registration is missing in browser, under 'Sound, video and game controllers' Device Manager where it was previously before the upgrade.
How can I reinstall my audio Unimodem half duplex driver without roll back my BCM upgrade?
My audio driver is not my problem. The speaker still works in my Modem when I have dial-up. Otherwise, the rest of my sound works fine, so I don't think I need an audio driver. What's missing on my upgrade was my driver for unimodem half duplex, and everything remained the same after the upgrade.
Here's what's happening. Often, I reinstall my OS together by formatting my hard drive. After the initial installation and install the drivers for Dell provided, my modem works fine, but at a slower speed. When I switched I hear the dial through my external speakers, which I prefer because I have restriction of hearing Audio and can hear it better amplified by the modem speaker.
When I install the update to windows BCM, it accelerates the rate of transfer of my modem, I like, but it removes my driver audio unimodem half duplex, which means I can hear is no longer my dial-up connection to know everything is going well. The sound comes directly to my modem card, however, due to the location under my desk, my PC I can barely hear the connection is established and can not use this sound for diagnostic purposes if I can't connect. It allows to hear the connection to remind me in case the line is disconnected or the phone company disconnects and provides their voicemail automated on how to restore our service.
I just want to still hear my modem amplified through my external speakers without losing speed BPS who provided me the upgrade.
Not yet tried to use the dell service tag for Dell drivers. Don't know how to specify this tag, or if it would provide other drivers that I already downloaded, but will check the next.
In the meantime if anyone has a useful answer as to how I can get my external returning without sacrificing my BPS speed increase, I would like to hear it.
Thanks for all the answers everyone, even if for the time being not useful yet.
I don't think that it is half-duplex driver Unimode (even if I'm wrong). My XP3 box has a Unimodem full-duplex audio driver "" list in the device under ' Audio, video and game controllers' Manager, and I've never had the modem sounds come through the main speakers. [The difference between "half-duplex" and "full-duplex" is if you wait until a part expresses before the start of the other or if both parties can talk at the same time.]
Rather, apparently some - but far from everything - modem drivers have a checkbox somewhere in the modem properties dialog box (accessed through Device Manager or control panel > modems Options and) who runs the sound of the system's external speakers.
While you're in the control panel > phone and Modem Options, click on the "Advanced" tab and check the Unimodem 5 Service provider is installed. It must have been installed by default, but if not, you might want to add (using the 'Add' button).
I suspect that your previous modem driver - which limited the speed of your connection - had the external speaker box, but that the new driver - who has more speed - connect does not work.
It is probably not very satisfactory, but you can increase the volume of the tiny speaker of the modem (a little) by using the "Additional initialization commands" box in the "Advanced tab" in the modem properties dialog box. There are two relevant orders, the order of M (which determines when the speaker is on) and the command L (which sets the volume of the speaker):
M0 speaker always off [that's a zero]
M1 Speaker is activated when the modem is off the hook and the carrier is not detected. [default]
M2 The speaker is always on.
M3 Speaker is activated after dialing the ends and turns off when the carrier negotiation is complete.L0 low volume
L1 low volume
L2 medium volume
High volume of L3Orders are entered, preceded by "AT" (without the quotes) in the box "Additional initialization commands", and there is no spaces. Thus, for example, if you want to hear the sounds, most at very high volume (which unfortunately is usually not very high), you define L3 and M3 by entering the following text in the box:
ATL3M3
With regard to the number of Dell's Service: on the page linked in my previous post, there is a link "enter serial number". If you click on this link there is a box to enter your Dell service tag (and yet another link to tell you how to find if you don't know where it is). Dell uses the "service tag" to identify your specific computer hardware configuration, because the same model Dell (e.g., Dimension 2400) can come with a variety of different hardware options. Using the service tag is supposed to customize the material presented to you so that it is applicable to your computer.
Sorry I couldn't give you a better answer on your modem sounds.
-
Hosts:
I used this same switch 5 ports for awhile but removed that I is no longer necessary to share the connection. Now, I needed to reuse the switch. I connected the cable between the router and the swih e-NET and the port fire lighted up as expected. Whenever I plug a cable to any port LEDS to blink just as well as the connected computer report that a network cable is unplugged. The wiring is good because I can connected to other computers and router and internet access.
When you connect the Ethernet cable to the switch and the computer you see all the lights on the Port Lan Switch?
When you connect the switch cable to the computer, disable and enable the connection to the Local network, then check if it still shows the same message. If still the same problem try to reduce the map of your network card on your computer.
Click on the Start button > Panel > network connections > right-click on icon "' connection to the Local network'" and select properties-here click on the button click "Configure" on the "Advanced" tab - In the area of 'Property' to highlight the link speed and duplex/connection network/type or type of media - and in the "value" box to select 10 MB/s half duplex / 10 half mode base T/10 basic and click OK.k OK.
-
Hello
CAVEAT! THIS IS AN ADVANCED TECHNIQUE TECH SOLUTION WITH OUT OF WARENTEE ROUGHTERS. IF LINKSYS SUPPORT CAN HELP YOU, USE IT ADAPTS ITS SERVICES TO FIRST! THIS PROCEDURE MAY OCCUR IF PURMADENT LOSS OF USE OF YOUR MORE ROUGH. THIS WORKED FOR ME, IS NOT FOR YOU!
Location:
Linksys WRT310n V1
Power continuous LIGHT
LAN port LED
Wireless LED off
NO RESPONSE AT ALL!
PC hardware tested (only one is necessary):
Card PC card Vista laptop.
Map of gigabits Vista desktop.
Software to download / install:
Installed the vista Control Panel TFTP client
Download linksys TFTP
Download the linksys firmware (own firmware v1 material!)
Method and procedure:
Connect the power supply and the computer lan cable.
Open a startup ping roughter to back.
ping 192.168.1.1 t w 5
No response is to be expected at this stage.
On the computer, open your network connections folder
Disable all OTHER network interfaces. (ALL OTHERS)
Go to the settings of the interfaces lan.
Disable (uncheck) then all options other tcp/ip v4
set the address of the card manual to
192.168.1.10 ip
255.255.255.0 void
192.168.1.1 door
192.168.1.1 dns
Yet, in the network adapter, configure the properties above the network card for 10 half-duplex speed mine was called the line speed and duplex.
Save and close.
NOTE: Do not release the reset button until it says to! You will need to hold it down for a long time!
NOTE: when you hold the reset for 30 seconds, the LAN port may be flashing around 5 and 15 seconds, do not pull on the power until the local network is off about 25 to 35 seconds of holding
On the rougher, with the power and lan cable connected.
Press and hold the reset button for 30 secconds you will see the port of lan cable turn arround this point draw power.
Hold the reset and wait 10 seconds.
Press and hold the reset and power for 30 seconds until the lan cable off then
OK, so with the power off you can release the reset button.
from now own that you can start from here to delivery to zero if the first attempts to send the new firmware for the linksys fails.
Open a NEW dos prompt.
type 192.168.1.1 put C:\linksysfirmware.bin-i TFTP
If you press on enter it will fail... so let it expire... If you type it again and wait to hit enter.
while now in the power of reset button on the release of roughter, reset after 5 secconds.
Press enter on the prompt back. You can send it a few time arround now it took three tryes to get the message 'SENT COMPLETE' tftp! You also see your pings in the other window start working! If you work to WAIT 2 min before doing anything then.
If you fail for more that 1 min, unplug your roughter and start sending the firmware.
OK so it's ping that's all? Yes!
OK, so you've waited 2 minutes, then press the power normally and wait 10 secconds to return to power with our reboot! Start it normally.
After that 20 secconds the roughter should be able to ping... anything else again!
Use the TFTP Linksys program now... and install complete firmware to the roughter!
When the message says firmware full wait two minutes and then pull the power and restart.
FACT!
Go back and re-read the instructions. Step by step exactly fallow or it does not work is that TECHNIQUES of ADVANCED advice. If you do not understand the thies steps you shouldn't try it yourself.
Thank you.
Maybe you are looking for
-
Satellite A660 (12 X) won't turn on
I downloaded a BIOS update, and at the time wherever I run it, the laptop froze. No response from keyboard or mouse movement. I let it be for a few hours and it has not yet moved. I tried to turn it off, and it did not work. Long press the power butt
-
Application of the rules of mail on only some accounts
I have 4 accounts IMAP entering Mail - one is, of course, iCloud. Two are not, they come from my own URL and one is an Exchange Server. I would like to have a set of rules that apply only to NON Exchange accounts = I don't want to filter e-mail Exc
-
Convert relative time in absolute
Hello I want to convert my string of relative time in a channel of absolute time. How this could be done? My relative time string has the format 01/01/00 12:29:17.9120 depending on whether I just want to generate the digital absolute time string. Tha
-
get drivers for computer hp laptop 15-r033tx
I need drivers.my model number is15-r033tx laptop, for windows 7 (32-bit & 64-bit both).Help, please.
-
I reinstalled my Windows XP Pro Version 2002 and I can not find the service pack downloads. You will need to download SP1a and SP2. Can someone help me?