Hash IP switch configuration

Similar Questions

• IviSwitch loses value when sending, "configure the switch" configuration = TRUE

  Hi all

  We are currently assessing Teststand 4.1 with a multimeter keithley 3706 switch system.

  After a first enthusiasm, thinking this tool with the meter switch fits perfectly our needs, real life seems difficult.

  Between several other problems, we must say to the device, the channel "s1com1" and "s1com2" are strings of configuration.

  Configure the teststand step: change the switch step IVI-> IVI, switching, configuration switch: channels "s1com1" Configuration = True

  led to observable in both actions in Ni Spy:

  GetAttributeViBoolean (..., "s1com1", _IS_CONFIGURATION_CHANNEL, VI_FALSE)

  SetAttributeViBoolean (..., "s1com1", _IS_CONFIGURATION_CHANNEL, VI_FALSE)

  manually call to this function of the interactive a CVI fp class works as expected (the VI_TRUE updated)

  Is there any hint that we could do wrong? Currently, we are just before writing wrappers in cvi and jump all the wonderful Types of IVIStep in teststand.

  Looking forward to any comments

  David Clus

  David-

  This would have the same problem we discovered recently in our internal tests. For the problem that we found, we will probably include our fix in a next corrective patch. You can check if the problem persists if you change your locale in English in the control panel? If the problem no longer occurs, can you use this as a workaround for now?

• LAG does not not after more Guide of switch Configuration for EqualLogic San steps in the document.

  We use the information provided in the following document: i.dell.com/.../dell-networking-n4000-series-switch-configuration-guide-for-equallogic-sans.pdf

  We have two switches of N4032F which are stacked and followed almost word for Word from this document.  We do not use DCB.  We are trying to set up a SHIFT and follow-up step 2.11 in the document, but it seems that the SHIFT does not work.

  Switch 1:

  serial interface fortygigabitethernet 1/1/1-2

  No spanning tree portfast

  active in mode channel-group 1

  Switch 2:

  interface series fortygigabitethernet 2/1/1-2

  No spanning tree portfast

  active in mode channel-group 2

  However, when it was discovered after changing these settings it shows them as being inactive.

  

  Can someone please help?

  Thank you

  Jeff

  Thanks for the additional information. When the switches are stacked, they act as a logical switch. Then when you plug with an OFFSET you are basically creating a loop and hook up a switch on himself. Desempilement switches and just use the OFFSET for the interconnection of the switch and you should see the GAL go active.

• The virtual switch configuration

  Hello

  I configured Vswitch on ESX4.0 connected with a teddy bear.

  There are Cisco catalyst 4503 L3 switch configured with several VLANS at the other end. I have configured the switch port trunk with dot1q encap mode that ends on the ESX4.0 server. Service console is configured with IP default VLAN, which is accessible from the other VIRTUAL networks. One of the virtual machine with Win2k3 OS is installed, but after configuration, I am not able to ping default gateway of VLAN respective or any other property intellectual VLAN.

  Can anyone guide me where I go wrong and how to correct the problem?

  Set the Group of ports to the VLAN specific you want the virtual machine to be on.  Do not put any VLAN ID in the virtual machine, just plug it into the port group.  If you have other virtual machines, or other on this virtual machine network interface cards that need to connect to the other VLAN create other Port groups for each VIRTUAL local area network required.

• The proSafe (JGS524E + GS116E) Switches: Configuration Management Web GUI in VLAN specific

  Hello

  I use a JGS524E and a GS116E. The two are connected via a 802. 1 q uplink with all defined VLANS in him.

  A 802. 1 q other interfaces goes to a pfsense firewall, which serves as a router and dhcp server for each VLAN that I use.

  How can I configure the switches plug are in one VLAN specific and get his IP address of the dhcp server in this VLAN?

  At present, it seems to be random access: it is not predictable that range from intellectual property, it takes its IP configuration via dhcp...

  How management function works internally?

  Thank you

  Markus

  Hello

  Thank you. I tried it out, but the behavior seems to be a little different:

  I configured a static IP address for the switch (10.1.0.13 / 24). I have access to the switch web gui via the ip address of the host of a host directly connected (connected via a trunk port, where I put 1 VLAN on the trunk), but it is all the same, what VLAN that I use:

  When it is connected to the VLAN 1 I have access, but also through 10 VLANS, VLAN 20 and so forth (assumed, I configure my computer appropriate staticly in the IP network, for example 10.1.0.20 / 24). So it seems not be limited only to the VLAN 1. You have access to each vlan, only the IP configuration must be in the same network.

  I'm not sure, how it behaves when cascading the two switches, I have not tried.

  If this information can be useful for other users with the same question about this switching product line.

  For me, this behavior is not very well implemented from my point of view. For security reasons, you must limit access to the administration, for example by allowing access from a specific hardware port or a vlan. With the effective implementation, centralized management for a cascade topology is not easy to set up, perhaps because the behavior is not very clear and not documented in the manuals.

  Mentioned on the edge: there is no available TLS/SSL encryption when accessing the web gui (not https). So the password is transmitted in clear text... not a very good idea, I think.

  Thanks a lot for your help.

  Best regards

  markusd112

• The Switch configuration and Wi - fi router in the same network

  Hi team,

  I have here is the configuration currently as below in the image. To describe the same internet cable is connected to a Cisco switch, which is connected to the PC in LAN (wired). A switch output is connected to the entrance of the wireless router Netgear Nighthawk AC 1900 Smart model of WiFi router # R6900. Wireless devices (laptop) are connected by the router.

  Each device has internet access. However, I am unable to run software LAN or unable to share any file of devices connected to the switch to the connected wireless devices. I can't ping any device the device wireless wired.

  Can anyone suggest what are the settings that I should do or what are the steps I should follow that will make wireless and wired devices in the same network.

  PS Plus early I tried the internet connection to the wireless router and then out of the router to pass, which has solved this problem. But slowing down my internet speed in wired devices. So, is it possible to have all devices in the network even with the current configuration?

  

  Thanks in advance.

  Best,

  Hardik

  I made wi - fi router reset hardware and configured in Access Point mode, that solved my problem.

• 32 x 1 double switch configuration PXI-2527 and TB-2627

  Looking for configuration of the PXI-2527 at double 32 x 1 using a TB-2627 terminal block.  Under the OR rocking support for topology multiplexer NI PXI/SMU-2527 1 double wire 32 × 1 -.

  (link - http://zone.ni.com/reference/en-XX/help/375472C-01/switch/2527_dual_1-wire_32x1_mux/) it displays the names of software for different PIN numbers.  I don't care actually on this subject because I use the Terminal Board, but what worries me is that the diagrams represent Ch0-Ch31 connection com0 + and Ch32-Ch64 to com1 + and there is NO mention of com0 - or com1.  However, the NI TB-2627 installation instructions, table 4 shows the mapping Terminal double 32 x 1 1 - Wire topology.  In this map, IT lists a software name and the name of Terminal for com0 - and com1-.

  My question is, if com0 and com1 - are not listed in the manual switch why are the listed in the TB-2627 manul and what is it in this configuration?

  Thanks for your time.

  In the Setup instructions for the double configuration 32 x 1 TB-2627, she mentions Com0 - and Com1 - as a reference to inform the user what pin connects to since this same module can be used with other topologies. It is unnecessary for the topology of 32 x 1 information double since the switch card does not use these channels for this particular topology. Information is available for your reference, but does not neet to be connected to anything.

  Please let me know if any of this is unclear.

  Kyle K.

• As redundant N3024 switch configuration

  Dear all,

  Hi, I just get N3024 Dell as a main switch and X 1026 access.

  I try to create the topology like this:

  

  VLAN 10: 10.10.10.xxx/24

  VLAN 20: 20.20.20.xxx/24

  VLAN 30: 30.30.30.xxx/24

  VLAN 40: 40.40.40.xxx/24

  Just try using the interface vlan each switch.

  Switch:

  IP routing

  interface VLAN 10

  10.10.10.1/24 IP address

  The interface VLAN 20

  20.20.20.1/24 IP address

  The interface VLAN 30

  30.30.30.1/24 IP address

  Interface port 2

  switchport mode trunk

  B switch:

  IP routing

  interface VLAN 10

  10.10.10.2/24 IP address

  The interface VLAN 20

  20.20.20.2/24 IP address

  The interface VLAN 30

  30.30.30.2/24 IP address

  I think that my config is far from complete and not best practices...

  My question is, what should I configure on each N3024 Dell, so all them VLAN can connected to the Internet? (can create the support for the ip address of the Sonic Wall port)

  Please please need your help.

  Thanks before.

  -The VRRP VLAN must be the same on both switches.

  -That the master switch must have control of the track in place.

  -The connection between the switch and the firewall must be that it is own VLAN and does not part of VLAN VRRP.

  Here is a diagram that I put in place, it could help clear up some confusion.

  

• GANYMEDE + with 3560 cisco switch configuration issue

  Hi Forum,

  Here's my setup GANYMEDE + on my cisco 3560 switch and my question is, how can I configure the switch, if I would not type enable after I put the user name and password? with configs below, users will need to type activate whenever they connect to the switch in order to enter the user exec mode. Please let me know if there is something missing in my configs to help me avoid typing 'enable '.

  Thanks in advance,

  MacBookAir: ~ MacBook$ ssh [email protected]/ * /.

  Password:

  Switch > en

  Switch #show run | include the aaa

  AAA new-model

  AAA server Ganymede group + mpcc

  AAA authentication login default group Ganymede + local

  activate the default AAA authentication no

  AAA authorization exec default group Ganymede + authenticated if

  AAA authorization commands 1 default group Ganymede + authenticated if

  AAA authorization commands 15 default group Ganymede + authenticated if

  start-stop radius group AAA accounting dot1x default

  AAA accounting exec default start-stop Ganymede group.

  orders accounting AAA 1 by default start-stop Ganymede group.

  orders accounting AAA 15 by default start-stop Ganymede group.

  AAA accounting system default start-stop Ganymede group.

  AAA server RADIUS Dynamics-author

  AAA - the id of the joint session

  Switch #.

  Hello

  Add the level of privilege 15 control VTY line configuration.

   line vty 0 4 [..] privilege level 15 ! 

  Concerning

• The switch configuration of 6500 catalyst for IPS Inline the METHOD works

  I understand how to configure the switch Catalyst 6500 so that the monitoring of ports are access ports in two VLAN separate operation online.

  However, I don't see any document that describes how the desired VLAN traffic gets forced through the IPS.

  "Promiscuous" mode, you can use copy/capture VACL and forwards traffic wished the METHOD of analysis. I don't see how to get traffic desired through the IPS.

  Note that the 6500 host is running native SXE IOS 12.2 (18).

  Thanks for any help.

  A transparent firewall is a pretty good comparison.

  Say you have vlan 10 with 100 PCs and 1 router for the network.

  If you want to apply a transparent firewall on this vlan you can put not just the Firewall interface on vlan 10. Nothing would go through the firewall.

  Instead, you need to create a new vlan, say 1010. Now you place the Firewall interface on vlan 10 and the other on the vlan 1010. Nothing is still going through the firewall. So now move you that router from vlan 10 to vlan 1010. Everything you do is to change the vlan, IP address and the mask of the router remain the same.

  The firewall transparent bridge vlan 10 and vlan 1010. The SCP on the vlan 10 ae is able to communicate and through the router, but must go through the transparent firewall to do.

  The firewall is transparent because there no IP Route between 2 VLANS, instead, the same IP subnet is on the VLAN and the transparent firewall ensuring the beidges between the 2 VLANS.

  The transparent firewall can do firewall between the SCP on the vlan 10 and the router on vlan 1010. But PC has vlan 10 talks for PC B on vlan 10, then the transparent firewall does not see and cannot block this traffic.

  An InLine sensor is very similar to the transparent firewall and will fill between the 2 VLANS. And similarly an InLine sensor is able to monitor InLine between PCs traffic on vlan 10 and the router on vlan 1010, but will not be able to monitor the traffic between 2 PCs on vlan 10.

  Now the PC on the other vlan and the router on a virtual LAN is a classic deployment for the sensors online, but your VLAN need not be divided in this way. You can choose to place some servers in one vlan and desktop to another vlan. You subdivide them VLAN to whatever the logical method for your deployment.

  Now for the surveillance of several VLANs the same principle still applies. You can't control traffic between machines on the same vlan. So for each the VLAN that you want to analyze, you will need to create a new vlan and divide the machines between the 2 VLANS.

  In your case with Native IOS, you are limited to only 1 pair of VLAN for InLine followed, but your desired deployment would require 20 pairs of vlan.

  The IPS 5.1 software now has the ability to manage the 20 pairs, but the native IOS software doesn't have the ability to send the 40 VLAN (20 pairs) to the JOINT-2.

  Changes in native IOS are in testing right now, but I have not heard a release date for these changes.

  Now cat BONES has already made these changes. So here is a breakdown of basic of what you could do in the BONE of cat and you can use to prepare for a deployment native IOS when it came out.

  For VLAN 10-20 and 300-310, you want monitored, you will need to break each of those VLANs in VLAN 2.

  Let's say that keep us it simple and add 500 to each vlan in order to create the new VLAN for each pair.

  Therefore, the following pairs:

  10/510, 511/11, 12/512, etc...

  300/800, 801/301, 302/802, etc...

  You configure the port to probe trunk all 40 VLAN:

  set the trunk 5/7 10-20 300-310 510-520 800-810

  (And then clear all other vlans off this trunk to clean things up)

  In the configuration of JOINT-2 create the 20 pairs of vlan inline on interface GigabitEthernet0/7

  NW on each of VLAN original 20 leave the default router for each LAN virtual vlan original to the vlan 500 +.

  At this point, you should be good to go. The JOINT-2 will not track traffic that remains inside each of the 20 VLAN original, but would monitor the traffic is routed in and out of each of the 20 VLAN.

  Due to a bug of switch, you may need to have an extra PC moved to the same vlan as the router if the switch/MSFC is used as the router and that you deploy with a JOINT-2.

• Cisco Catalyst 2960-S switch configured for 802. 1 x sends a query to access the Radius Server Radius

  Setup

  Cisco Catalyst 2960-S running 15.0.2 - SE8

  Under Centos freeRadius 6.4 RADIUS server

  Client (supplicant) running Windows 7

  When Windows client is connected to the port (port 12 in my setup) with authentication of 802. 1 x active switch, show of Wireshark that catalyst sends ask EAP and the client responds with EAP response. But it made not the request to the Radius server. The RADIUS test utility 'aaa RADIUS testuser password new-code test group' works.
  Here is my config running. Any advice would be greatly appreciated.
  #show running mySwitch-
  mySwitch #show running-config
  Building configuration...

  Current configuration: 2094 bytes
  !
  version 12.2
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  hostname myswitch
  !
  boot-start-marker
  boot-end-marker
  !
  activate the password secret 5 $1$ Z1z6$ kqvVYRQdVRZ0h8aDTV5DR0 enable password!
  !
  !
  AAA new-model
  !
  !
  AAA dot1x group group radius aaa accounting dot1x default start-stop radius authentication group!
  !
  !
  AAA - the id of the joint session
  1 supply ws-c2960s-24ts-l switch
  !
  !
  !
  !
  !
  control-dot1x system-auth
  pvst spanning-tree mode
  spanning tree extend id-system
  !
  !
  !
  !
  internal allocation policy of VLAN no ascendant interface FastEthernet0 no stop ip address!
  GigabitEthernet1/0/1 interface
  !
  interface GigabitEthernet1/0/2
  !
  interface GigabitEthernet1/0/3
  !
  interface GigabitEthernet1/0/4
  !
  interface GigabitEthernet1/0/5
  !
  interface GigabitEthernet1/0/6
  !
  interface GigabitEthernet1/0/7
  !
  interface GigabitEthernet1/0/8
  !
  interface GigabitEthernet1/0/9
  !
  interface GigabitEthernet1/0/10
  !
  interface GigabitEthernet1/0/11
  !
  interface GigabitEthernet1/0/12
  switchport mode access
  Auto control of the port of authentication
  dot1x EAP authenticator
  !
  interface GigabitEthernet1/0/13
  !
  interface GigabitEthernet1/0/14
  !
  interface GigabitEthernet1/0/15
  !
  interface GigabitEthernet1/0/16
  !
  interface GigabitEthernet1/0/17
  !
  interface GigabitEthernet1/0/18
  !
  interface GigabitEthernet1/0/19
  !
  interface GigabitEthernet1/0/20
  !
  interface GigabitEthernet1/0/21
  !
  interface GigabitEthernet1/0/22
  !
  interface GigabitEthernet1/0/23
  !
  interface GigabitEthernet1/0/24
  !
  interface GigabitEthernet1/0/25
  !
  interface GigabitEthernet1/0/26
  !
  interface GigabitEthernet1/0/27
  !
  interface GigabitEthernet1/0/28
  !
  interface Vlan1
  IP 10.1.2.12 255.255.255.0
  !
  IP http server
  IP http secure server
  activate the IP sla response alerts
  recording of debug trap
  10.1.2.1 host connection tcp port 514 RADIUS-server host 10.1.2.1 transport auth-port 1812 acct-port 1646 timeout 3 retransmit testing123 key 3.
  Line con 0
  line vty 0 4
  password password
  line vty 5 15
  password password
  !
  end

  interface GigabitEthernet1/0/16
  !
  interface GigabitEthernet1/0/17
  !
  interface GigabitEthernet1/0/18
  !
  interface GigabitEthernet1/0/19
  !
  interface GigabitEthernet1/0/20

  Have you run wireshark on the server because the request to switch? If so you make sure that there is a response from the server? For Windows network POLICY Server (I've never tried Centos), you must ensure that the request is related to a policy which then authenticates, or denies access. Usually, it is a matter of such attributes and the seller.

  Regarding the configuration, it seems a bit out of the AAA. Try to remove the:

  line "aaa dot1x group service radius authentication" and this by using instead:

  "aaa dot1x default radius authentication group". After the dot1x word you are supposed to provide a list of the authentication or the default Word if you do not want to use a list.

• The ISE Cisco switch configuration

  Hi experts,

  I got the following network:

  Devices-> switch access-->--> access switch central office switch-> ISE Server

  All switches are capable IOS for the 802. 1 X and configurations of AAA for ISE to manage network devices. However, I read in the guide on the configuration of the switches in preparation for the deployment of the ISE of CIsco, but I wonder what should I configure switches for access and basic switches or only configure the switches for access to EHT?

  Thanks for your time to read!

  If all clients are non-DHCP clients, then no configuration is based or distribution at all.

  But you may need to search different options of profiling, if the customers are not active DHCP. Access switch supports the function of detection IOS? Would be very useful to have such a that it would send important profiling information at ISE. You may need to use the right options for ISE of profiling to determine the details of the endpoint.

  Concerning

  Vivek

• me is Anish and am facing some problems in IM sg30052 ports switch configuration

  Hai help me on this...

  Needs of users

  (1) switch is configured with an ip address of management 172.16.7.x

  (2) two VLAN has created tobe 114 & 115

  (3) configure the switch ports - access ports and must be assigned to one of the two VLAN as user requirement.

  (4) two switch ports must be configured as a trunk port.

  (5) port security must be enabled in all access ports.

  Hi Anish-

  1 - Connect to the console of the switch

  config t

  interface vlan 1

  172.16.7.x IP address

  2-

  config t

  database of VLAN

  VLAN, 114, 115

  3-

  config t

  int gi01

  switchport mode access

  switchport access vlan 114

  int gi02

  switchport mode access

  switchport access vlan 115

  4-

  config t

  int gi48

  switchport mode trunk

  switchport trunk allowed vlan add 114, 115

  5-

  https://supportforums.Cisco.com/docs/doc-27753

  https://supportforums.Cisco.com/docs/doc-27720

  -Tom
  Please mark replied messages useful

• 5508 interfaces with two different switches configuration

  Hello

  I have a 5508 WLC and two 4507 switches that are configured in HSRP.

  Now, I want to configure 5508 interfaces:

  If I want to configure management interface, I need the physical port card

  Question: How can I correspond to two physical port that are connected to two different chassis?

  Configuration interface AP-Manager's optional?

  in this scenario, I'll have to divide AP traffic between two switches (EQ. Assume that 10 aps are, I want to connect to a switch and another 5 to another switch 5).

  How to divide?

  Please guide me to configure the interface in this scenario...

  I have with your answer.

  Hi Vinod,

  Wasn't this already answered here: https://supportforums.cisco.com/thread/2052962 ?

  HTH,
  Tiago

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• 2960 switch configuration for test of dark fiber

  Hi guys

  IM new in network. We have a dark fiber, tests aside > dark fiber > side (B) to test the fiber link, im using a switch 2960 and configure a vlan - vlan 31 and I assign port 1 to switchport access vlan 31. I'm not sure whether the switch need to configure a default gateway, which is the other tat switch side b. I'm not able to ping to my pc either [port 2/0/1]. the fiber link that connected to the switch's port 2/0/49]

  can you help me to check if this configuration is correct?  Here's the running configuration. TX a lot for the help.

  #sh SRO-SWITCH-TEST run
  Building configuration...

  Current configuration: 2679 bytes
  !
  version 12.2
  no service button
  horodateurs service debug uptime
  Log service timestamps uptime
  encryption password service
  !
  SRO-SWITCH-TEST hostname
  !
  boot-start-marker
  boot-end-marker
  !
  enable password 7 110A1016141D5F01072728
  !
  username admin privilege 15 password 7 00071A 150754
  !
  !
  No aaa new-model
  clock timezone 8 MYS
  switch 2 supply ws-c2960s-48ts-l
  !
  !
  !
  !
  !
  pvst spanning-tree mode
  spanning tree extend id-system
  !
  !
  !
  !
  internal allocation policy of VLAN ascendant
  !
  property intellectual ssh version 2
  !
  !
  interface FastEthernet0
  no ip address
  !
  GigabitEthernet2/0/1 interface
  switchport access vlan 31
  switchport mode access
  No auto mdix
  spanning tree portfast
  !
  interface GigabitEthernet2/0/2
  !
  interface GigabitEthernet2/0/3
  !
  interface GigabitEthernet2/0/4
  !
  interface GigabitEthernet2/0/5
  !
  interface GigabitEthernet2/0/6
  !
  interface GigabitEthernet2/0/7
  !
  interface GigabitEthernet2/0/8
  !
  interface GigabitEthernet2/0/9
  !
  interface GigabitEthernet2/0/10
  !
  interface GigabitEthernet2/0/11
  !
  interface GigabitEthernet2/0/12
  !
  interface GigabitEthernet2/0/13
  !
  interface GigabitEthernet2/0/14
  !
  interface GigabitEthernet2/0/15
  !
  interface GigabitEthernet2/0/16
  !
  interface GigabitEthernet2/0/17
  !
  interface GigabitEthernet2/0/18
  !
  interface GigabitEthernet2/0/19
  !
  interface GigabitEthernet2/0/20
  !
  interface GigabitEthernet2/0/21
  !
  interface GigabitEthernet2/0/22
  !
  interface GigabitEthernet2/0/23
  !
  interface GigabitEthernet2/0/24
  !
  interface GigabitEthernet2/0/25
  !
  interface GigabitEthernet2/0/26
  !
  interface GigabitEthernet2/0/27
  !
  interface GigabitEthernet2/0/28
  !
  interface GigabitEthernet2/0/29
  !
  interface GigabitEthernet2/0/30
  !
  interface GigabitEthernet2/0/31
  !
  interface GigabitEthernet2/0/32
  !
  interface GigabitEthernet2/0/33
  !
  interface GigabitEthernet2/0/34
  !
  interface GigabitEthernet2/0/35
  !
  interface GigabitEthernet2/0/36
  !
  interface GigabitEthernet2/0/37
  !
  interface GigabitEthernet2/0/38
  !
  interface GigabitEthernet2/0/39
  !
  interface GigabitEthernet2/0/40
  !
  interface GigabitEthernet2/0/41
  !
  interface GigabitEthernet2/0/42
  !
  interface GigabitEthernet2/0/43
  !
  interface GigabitEthernet2/0/44
  !
  interface GigabitEthernet2/0/45
  !
  interface GigabitEthernet2/0/46
  !
  interface GigabitEthernet2/0/47
  !
  interface GigabitEthernet2/0/48
  !
  interface GigabitEthernet2/0/49
  switchport access vlan 31
  switchport mode access
  Nonegotiate speed
  spanning tree portfast
  !
  interface GigabitEthernet2/0/50
  !
  interface GigabitEthernet2/0/51
  !
  interface GigabitEthernet2/0/52
  !
  interface Vlan1
  no ip address
  Shutdown
  !
  interface Vlan31
  Description OFFICE SRORO
  IP 192.168.31.250 255.255.255.0
  !
  IP http server
  IP http secure server
  !
  Line con 0
  line vty 5 15
  !
  end

  SRO-SWITCH-TEST #.

  Hey the config looks ok just disappeared locally pointing to the other switch, default gateway as you say

  PC must be set with the 192.168.31.250 gateway vlan 31 and have a static ip address in the same range and same subnet

  Make sure that your vlan 31 is to the top/top