"He's dead, Jim" error on shutdown

Similar Questions

• Purple reading screen "he's dead, Jim."

  I have twice been signing my laptop Dell Inspiron 1710 with Windows 7 Professional, and when a purple reading "he's dead jim" screen for just a millisecond.  It scared me out of my socks.

  Anyone know what it is? What is it associated with?  Who/what/why it happens?  I immediately ran my articles to spy, my anti-virus, my anti-malware, etc. and silently thank my lucky stars that I backed everything up.
  I find a lot of references to purple screens and "he's dead, jim" (apparently from Star Trek), even within the same reference, but nothing that tells me that all more than just that.
  Thank you, one and all.
  Thank you

  Run these two free versions

  http://www.Malwarebytes.org/MBAM.php

  http://www.SUPERAntiSpyware.com/

  And if it cures, clearly, you need to change your application of malware

• Error "unexpected shutdown windows" and the need to restart the computer

  Original title:

  I use Windows Vista, I get the message "unexpected shutdown of windows" and I'm having to reboot is a solution to the Please this problem?

  Hello

  1. Once you get this error message?

  2. are you aware of any changes made to the computer, before the show?

  Method 1:

  Step 1: Safe Mode

  Start your computer in safe mode and check the number.

  Start your computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Step 2: Clean boot

  If you are not facing the problem in safe mode, and then put your computer in a clean boot and search for the question.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: Once you are done with the boot, follow step 7 of article to put your computer to normal startup.

  Method 2:

  Update all the device drivers for your computer.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  I hope this helps.

• STOP: c000021a {fatal system error} during shutdown

  I have Windows XP SP3 running on an old laptop Asus L2000 who remains perfectly functional.

  Whenever I stopped him, this BSOD stop: c000021a {fatal system error} and something on the logon process terminated unexpectedly pop and the laptop just stays on like that until I hit the button to power only, then it will turn off. In the contrary case, the laptop runs normally.
  I looked everywhere but nothing is done, nobody gives never a direct response to how which and where to fix the problem.
  This problem started after a process of full consolidation (anti-virus, registry and the batch recovery) after an escape of the virus. Now the system is clean.
  Is there a particular way or procedure to get rid of this problem?

  Hi aaavvv,

  This error can occur when you have GoBack installed on your computer and it is present in the boot sector.

  GoBack causes a Stop C000021a error

  http://support.Microsoft.com/kb/316503

  Also see the article below and check if it helps.

  How to solve an error "STOP 0xC000021A.

  http://support.Microsoft.com/kb/156669

• Explorer.exe error on shutdown

  I have a new HP Pavilion with Windows 8 64 bit laptop. I just downloaded the free update to windows 8.1. And then the trouble started.
  First, startup time has almost doubled. Just before the desktop becomes visible, there is a period of 10 seconds where everything you see is a black screen. Sometimes, it is more than 10 seconds. Then we see the wallpaper.
  Second, the most annoying problem - whenever I have shut down or restart, I get an error in explorer.exe saying memory cannot be read in memory of some instruction referenced to 0x00000000. ?! What the h - what? I mean that's what we expect to see that after the update to Windows 8.1? This is ridiculous. This affects many people everywhere in the world and there is not yet any official patch or the announcement?

  I have read similar messages on the web and none of the solutions work. Someone said: change the registry, someone said to remove the bluetooth start service? nothing and stop a bluetooth service is not a solution. Why wouldn't I be able to use bluetooth to solve this error Windows 8.1?

  Please correct this urgent problem. And DO NOT ask us to re - install windows... I mean come on... You think that people have nothing better to do than Windows install/reinstall all day long? Bandwidth is not cheap anywhere in the world either. Please release a patch or guidance on the resolution of this problem as soon as POSSIBLE.

  Hey Crusader8,

  Here is the driver for the network cards of your product page.

  Hope this helps you.

  Thank you.

• hpqgpc01.exe dialogue Application error on shutdown

  When I stop, I get a dialog box error saying that hpqgpc01.exe Application error occurred at a particular address.

  When I close the dialog box, complete closure.

  What can I do to fix this?

  Tom R. posted what worked for me:

  For 64-bit systems. But you're probably using a 32-bit file system. So, lets try it. Load your printer disk in your CD drive, then go to: START, control PANEL, PRINTER. Then right-click on the printer and select Properties. Go to the SHARING. Click CHANGE SHARING OPTIONS. Click CONTINUE. Go down to the DRIVERS and click ADDITIONAL DRIVERS.  X 64 is 64-bit driver, but don't forget that you probably have the files loaded in your X 86 file, which is 32-bit. Let the X 64 single file, but click on the X 86 file. Then close the program. When you return, the file should show Nokia X 64 & X 86 as Type 3 User Mode INSTALLED-YES. When you turn off the computer you will be always see the file hpqgpc01.exe pop up as you will need to restart the computer for the change to take effect. But after that, you should not see the error sign on your next stop down. Hope that helps. Let me know if it works for you.

• Blue screen error: Failed Shutdown 0x000000fe

  original title: stop failed!

  When I try to shut down my computer, he acts like he's going to close, goes to a black screen and then just restarts.  Once it restarts I get a window of Windows error asking if I would look online for a solution.  When I say, Yes, the box indicates that she is looking and then disappears without offering a solution.  I copied the details of the error and they are listed below:

  Signature of the problem:

  Problem event name: BlueScreen

  OS version: 6.0.6002.2.2.0.256.1

  Locale ID: 1033

  More information about the problem:

  BCCode:                                              fe

  BCP1: 0000000000000008

  BCP2: 0000000000000006

  BCP3: 0000000000000006

  BCP4: FFFFFA8006D19570

  OS version: 6_0_6002

  Service Pack: 2_0

  Product:                                              256_1

  Files helping to describe the problem:

  C:\Windows\Minidump\Mini071210-01.dmp

  C:\Users\Frances Sauders\AppData\Local\Temp\WER-55906-0.sysdata.xml

  C:\Users\Frances Sauders\AppData\Local\Temp\WER2D40.tmp.version.txt

  Can someone tell me how to fix this?

  Thank you

  drfrances

  Try a system restore to a Date before the problem began:

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  http://www.windowsvistauserguide.com/system_restore.htm

  Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

  See you soon.

  Mick Murphy - Microsoft partner

• My computer started randomly closing overnight - then the left on download. Internet points out the unexpected stop down and gives me a link dead at error number: 0x8DDD0002 - I'M the only user/administrator

  I've been downloading for years, but the last 3 - 4 times when I let the computer do its things while I'm in bed, I come down in the morning and the computer restarted itself and I get the Vista - computer has recovered from an unexpected stop, then he gives me the windows update link, which tells me that I must be an administrator to apply updates!  I AM she!  only one user on this computer, checked my settings and its fine!

  Someone has any ideas why this started all of a sudden the most stupid and frustrating now!

  Thanks in advance people :D

  "computer has recovered from an unexpected shutdown, then he gives me the windows Update link.

  Most of the time, it restarts itself during the update process.

  Change it to no automatic installation, which is what I was hoping you would do to dismiss this case.

  That's what brought me to update problems.

  See you soon.

  Mick Murphy - Microsoft partner

• T400 2767-WC8 stops with the error "System shutdown due to overheating graphics card"

  Hello

  I'm running a 2 years T400 2767-wc8 with a graphics card ATI to the switchable address.

  For two weeks, I have the following problem:

  If my system is under load (compilation, photoshop, that sort of thing), it stops randomly. The laptop is not immediately turn off, the LED twinkle again for 2-3 seconds. After this period, it is off.

  Subsequently, a restart shows the 'Starting Windows' logo, then a black screen. To solve this problem, I have to start once in safe mode, and then everything works.

  I just reinstalled Windows 7, but the problem persists. If I disable the ATI graphics card, everythink is ok, but I can't use my external 24 "

  The systemfan breath, but the temperature of the gpu in idle mode goes up to 80 ° C.

  Could someone give me a hint, I can try to solve this problem?

  Greeting

  Hi Kicker,

  usually, I use my laptop on a desk or in the docking station. The radiator seems to be tightend.

  OK, so I should call lenovo...

  Why buy a T400 with SWITCHABLE graphics :-/

  Thank you very much!

• error 3001F

  I have an iMac and when reinstall us OS X from time capsule erase us data and have problem reinstalling all reflection because all time have this message (apple.com support / 3001F)

  With this sign

  others seem to have had the same problem

  MacBook Pro dead - '-3001F' error

  more

  Apple.com / support 3001F

• When I try to start my computer, the Blue error screen appears saying Stop: 0x0000007B (0x80399BB0, 0 C 0000034, 0x00000000, 0x00000000)

  Original title: cannot start my computer

  When I try to start my computer, the dead Blue error screen appears saying Stop: 0x0000007B (0x80399BB0, 0 C 0000034, 0x00000000, 0x00000000)

  Hi WindowsxpUser,

  ·         Did you do changes on the computer before the show?

  ·         What is the brand and model of the computer?

  Follow the steps in the article.

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly

  http://support.Microsoft.com/kb/958233

  Error message when you start a Windows Vista or Windows 7 computer after changing the mode of the boot drive SATA: "STOP 0x0000007B INACCESSABLE_BOOT_DEVICE".

  http://support.Microsoft.com/kb/922976

• Windows 7 freezes, sometimes shows bluescreen and shows different errors

  Over the last 2 or 3 weeks, I had intermittent problems with my pc. Packard Bell iXtreme 6620 UK.

  I got a pc of HRT for a few months.
  When I acquired, I added an extra hard drive and I replaced the wifi card
  with a USB ports.
  Since then, the only change is a new graphics driver.
  No hardware or software changes for at least 3 months.

  Problem just started occurring a couple of weeks.

  Most of time, I have no problems running Win7, but sometimes the
  PC won't start, just beeps and restarts. This is it 2 or 3 times,
  and it can offer repair system. If I don't, then try to
  restart normally, and then usually it starts ok. If I accept it then
  says it is the repair, then try to reboot. I usually then power
  downwards.

  Sometimes during the restart cycle where I put upward, then after a
  shortly, I get a continuous beep of high slope and nothing else happens.
  I've then power off, and if I leave for about 10 minutes, then it usually
  restarts ok.

  Sometimes when I walk to get the Packard Bell splash screen, then the
  PC crashes, nothing else is happening.

  Sometimes I get to the Windows startup screen that says only: departure
  Windows and once again it hangs and nothing else happens.

  Sometimes when you run then the pc freezes. In this case, I usually for
  turn the power off and tell it to start normally when I turn on again. Generally
  in this case I do not get the above mentioned beep.

  Sometimes when it's cold, I get a BSOD indicating usually
  INTERRUPT_EXCEPTION_NOT_HANDLED.
  Stop: 0x0000003D
  (0xFFFFF880009CB1B0, 0 x 0000000000000000, 0xFFFFF880016FB50)

  Today, I also received the message
  ataport.sys
  Address FFFFF880016FBB5DA1FFFFF8800...

  I just got a message that the pc has been a mistake.
  Signature of the problem:
  Problem event name: BlueScreen
  OS version: 6.1.7601.2.1.0.256.48
  Locale ID: 2057

  More information about the problem:
  BCCode: 3B
  BCP1: 00000000C 0000005
  BCP2: FFFFF800032839E3
  BCP3: FFFFF88006CC0070
  BCP4: 0000000000000000
  OS version: 6_1_7601
  Service Pack: 1_0
  Product: 256_1

  Files helping to describe the problem:
  C:\Windows\Minidump\080614-21637-01.dmp
  c:\systemp\WER-52681-0.SysData.XML

  This occurred after the pc rebooted while I had an open file.

  Asked me if I wanted Windows to seek a solution. I answered Yes
  and after one or two seconds, the dialog box has disappeared without a message.
  I ran Memtest who reported everything is OK. From others
  suggestions that I found that I also ran TDSSkiller from Kaspersky.
  This also gave a certificate of good health.
  I had these problems again a few minutes, turned off and rebooted
  and all is well.

  I got a pc of HRT for a few months.
  When I acquired, I added an extra hard drive and I replaced the wifi card
  with a USB ports.
  Since then, the only change is a new graphics driver.
  No hardware or software changes for at least 3 months.
  Problem just started occurring a couple of weeks.

  Windows - custom views - administrative events Event Viewer gives the
  Next:

  Error:
  Filter event with the query "SELECT * FROM __InstanceModificationEvent WITHIN 60 WHERE TargetInstance ISA 'Win32_Processor' AND TargetInstance.LoadPercentage > 99" could not be reactivated in namespace '//./root/CIMV2' because of error 0 x 80041003.» Events cannot be delivered through this filter until the problem is resolved.

  Caution:
  The driver failed to load unit WpdBusEnumRoot\UMB\2 \Driver\WUDFRd & 37c186b & 0 & STORAGE #VOLUME # _____? _USBSTOR #DISK & VEN_GENERIC & PROD_MINI_SD_READER & REV_1. 06 #7 & 29D2AFC & 0 & 058F63776378 & # 4.

  Error:
  The computer was restarted after a bugcheck.  The bugcheck was: 0x0000003b (0xfffff800032839e3, 0xfffff88006cc0070, 0x00000000c0000005, 0 x 0000000000000000). A dump was saved in the: C:\Windows\MEMORY. DMP. Report ID: 080614-21637-01.

  Error:
  Audit events have been abandoned by public transport.  0

  Criticism:
  The system has rebooted without judgment properly first. This error can be caused if the system unresponsive, crashed or unexpected power loss.

  directly after
  Error:
  System shutdown prior to 16:48:33 on? 06 /? 08 /? 2014 was not planned.

  And:
  Filter event with the query "SELECT * FROM __InstanceModificationEvent WITHIN 60 WHERE TargetInstance ISA 'Win32_Processor' AND TargetInstance.LoadPercentage > 99" could not be reactivated in namespace '//./root/CIMV2' because of error 0 x 80041003.» Events cannot be delivered through this filter until the problem is resolved.

  Hello

  Thanks for posting your question on the forum of the Microsoft community.

  I would like to know some information about the problem so that we can help you better.

  1. have you installed Windows 7 Professional before the show?
  2. What is the exact model of your computer number?

  I appreciate your efforts to resolve the issue. Thank you also to provide details on the issue.

  The problem may occur due to device driver damaged or problems with the hard drive.

  I would suggest trying the following methods and check if it helps.

  Method 1:
  Remove all external devices connected to the computer except the mouse and keyboard and check the issue.

  If this does not help, then use method 2.

  Method 2:
  As you tried to run the memory test that shows that the memory has no problem, it is possible that the hard drive has some bad sectors, then I suggest you run the disk check and see if it helps.
  Refer to this article:
  Check your hard drive to find errors in Windows 7
  http://support.Microsoft.com/kb/2641432

  Note: When running chkdsk on the drive hard if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• Tandberg MPS 800 - crash and reboot, 0 detected dead of media card

  Hello

  I have problem with Tandberg MPS 800.

  For the first time, during the video conference with 12 clients, it crash and reboot your system with the 5th hour. All rooms have disappeared and I have to recreate the new conference room to recover.

  After a search on the event using the CLI command log, I find this:

  WEB: SSL handshake failed: Shutting down connection.
  Media card 0 dead, write error - size 104 (max 1792) - message to /dev/pcidrvtx0:
          RTP_Stat_Req (H323M,0)->(RtpStack,0)
  /dev/pcidrvtx0: terminated due to media card failure
  531089436 Exiting
  Log saved at Sat Dec 31 16:09:34 UTC 2011
  ## -- ## -- ## -- ##
  0x4000:ttos_main.c: TTOS_init(): Log File Start for ** PID=208
  Main thread, PID 208
  Thread WatchdogThread, PID 210
  Thread WatchdogKickerThread, PID 211
  Thread stdOutR, PID 212
  Thread stdOutW, PID 213
  Thread stdErrR, PID 214
  Thread stdErrW, PID 215
  Running J4.2, 2008-02-29, s41000
  Initializing entropy pool...
  Storing entropy pool initializer...
  Queue /tmp/fifos/HouseQ, QID 15
  Tabasco system detected
  Attached Media cards: 8,  PRI cards: 1,  V.35 cards: 0
  Thread remote, PID 216
  tabConf.nNumLlPri: 1
  cnf_NumOfPriTotal:   8
  cnf_NumOfPriPerCard: 0
  Thread WebSrv, PID 217
  Queue /tmp/fifos/WebWrk, QID 26
  Thread WebWrk, PID 218
  WEB: WARNING!  Using factory default certificate/private key.
  This is not secure
  Queue /tmp/fifos/Qsdl, QID 29
  

  The MPS 800 working again now, but I fear that if this problem happens again in the future.

  Should I replace Media Card 0 again to fix this problem? And physically what the Media Card 0, since the beginning of the slot with slot 1?

  Please suggest.

  Thank you in advance for any help you can provide.

  See you soon,.

  Ketut Mustika Wiguna

  HI Ketut - more that probably look at the entire record of the newspapers listed on the MPS to see what happened.  It would be better for you to prosecute TAC so that we can take a look.

  (1) include SN and SW version running on MPS.

  (2) WINSCP to members through root.

  3) browse to folder TANDBERG

  (4) here, you will see a folder named "logs."  Copy and paste this folder on your desktop.

  (5) DO NOT OPEN the file until after it was sent.  This destroys the time stamp on the files.

  (6) ZIP them and join SR.

  If you can, in the RS provide as much detail as possible about the call that was when recovery occurred.  It would give us a good idea about what happened.

  This message is really generic.  1 Media card may have left for some other reason that is not listed in the controller card connects.  Media card Logs in the logs folder where the importance of attaching them to the case.

  VR

  Patrick Pettit

• Vista restarts after 30 min. at the beginning and is OK, the rest of the day.

  Every day for the past 3 weeks every time that I log on, after 30 min. I get a reboot.

  I ran CCleaner and sys. restoration. I also disabled the automatic restart.
  A blue screen appears just before the restart that said ' Jim is dead Google is out of memory or...» »
  That's all I had time to read before restarting.
  Thank you
  Lambert

  http://chromestory.com/2011/01/HES-dead-Jim-the-new-sad-tab-for-Google-chrome/

  This seems to be an error of Chrome. It may be a symptom rather than the cause of the problem. What happens if we leave it for 30 minutes not including the chromium?

• My computer guard shut down by itself

  My computer for some reason some keeps stopping itself. Is not over heating or something like that and the power supply is good. I can completely start the computer, navigate or do anything else for about 20 minutes, but then something forces it to stop.

  I tried to do a restore system to factory settings, I ran scans of several viruses, Malware scans and spyware superanti Scan in Normal windows Mode and safe, and its not picking up anything. \

  Before I did a system restore I got one "he's dead jim" link from my browser chrome, and then my computer would be closed, but now its just stop with that. Can I stop sometimes when im running other programs, but it will just stopped again at another time.

  The computer is only about a year with Windows 7. Anyone have any ideas?

  Hello

  ·         You get an error message or code?

  I would say lets you check in the Event Viewer log and check for defective module that is causing the problem:

  http://Windows.Microsoft.com/en-us/Windows7/what-information-appears-in-event-logs-Event-Viewer

  As you have already restored the computer to the factory settings, this problem could be related to the hardware store. I suggest to check in for all devices Device Manager and also check the RAM.

  I suggest you contact the manufacturer for the unwanted material.