Help access remote in a 5505

Hi all. Need help with a remote in a 5505. I can vpn in fine, I can't pass any traffic. When I do a ' sho cryp ipsec her ", I see the traffic that is decrypted, but I see not all traffic is encrypted to me. I have attached to my config, I could get help from you guys to see where I have gone wrong? I appreciate as always.

Why it happens is because the ASA also has a L2L tunnel and you use same NAT 0 access-list to L2L tunnel as Crypto ACL also.

NAT (inside) 0-list of access tocw

card crypto outside_map 10 correspondence address tocw

If the traffic that you send from vpn client is actually back to L2L tunnel.

Follow these steps:

Create access list separate for tunnel L2L specifying only specific L2L tunnel traffic.

you need to check the remote side, but I think your crypto ACLs for l2l tunnel

Access extensive list ip 192.168.201.0 VPNACL allow 255.255.255.0 192.168.73.0 255.255.255.0

No crypto outside_map 10 correspondence card for tocw

outside_map card crypto 10 corresponds to the address VPNACL

Your L2L tunnel will descend when you make changes then make necessary arrangements.

Verify and validate results

HTH

Sangaré

Pls rate helpful messages

Tags: Cisco Security

Similar Questions

How a cRIO can access remote systems VISA resources?

I have a NI 9871 RS485 module on an ethernet 9148 RIO.

I have also a laptop and a cRIO 9073.

I can access each of the 9871 serial ports on the computer but not the 9073.

When you try to access it from the cRIO, I get error:-1073807192, VISA: (Hex 0xBFFF00A8) is denied access to the resource or to the remote machine. This is due to the lack of sufficient privileges for the current user or the machine.

How the cRIO can access the serial ports of the module 9871 on the ethernetRIO?

Or how a remote access cRIO visa resources?

Or how a cRIO can have sufficient privileges to access remote resources from visa?

Thank you for your help.

LabVIEW 2010 & VISA 5.1 on pc

NOR-RIO 4.0 and 5.1 VISA & NI 9871 SERIES scan engine support on cRIO and eRIO

Hi Woss,

It is possible that your RIO Ethernet has some parameters of active access which is to prohibit the connection to serial ports. You can change these settings in a position and Automation Explorer (MAX) for your device by going to the device under remote systems, expanding the category of software under it and choosing NI-VISA. There will be a tab in the right pane of MAX called Options of VISA. In this tab, select Server VISA > security to access these settings.

From there, you should be able to add the IP address of the RIO device that needs to access the VISA on the RIO Ethernet server. Once you have changed these settings, just click on register at the top of the window and allow the unit to restart. Let me know if that helps!

Split tunneling cannot access remote host

Hi guys,.

Having this problem by which I am able to connect the Anyconnect client but unable to ping / access of remote servers. See below for the config of the SAA;

Any ideas would be a great help, thank you!

ASA Version 9.1 (1)

!

ASA host name

enable the encrypted password xxxxxxx

xxxxxxxxxxxxx encrypted passwd

names of

mask of local pool AnyPool 10.0.0.1 - 10.0.0.10 IP 255.255.255.0

!

interface GigabitEthernet0/0

nameif outside

security-level 0

IP address 203.106.x.x 255.255.255.224

!

interface GigabitEthernet0/1

nameif inside

security-level 99

IP 172.19.88.254 255.255.255.0

!

interface Management0/0

management only

nameif management

security-level 100

IP 192.168.1.1 255.255.255.0

!

passive FTP mode

clock timezone 8 MYT

the SVR object network

Home 172.19.88.11

e-mail server in description

network of the NETWORK_OBJ_172.19.88.0_24 object

172.19.88.0 subnet 255.255.255.0

network of the VPN-POOL object

10.0.0.0 subnet 255.255.255.0

object-group Protocol TCPUDP

object-protocol udp

object-tcp protocol

object-group service DM_INLINE_SERVICE_0

ICMP service object

area of service-purpose tcp - udp destination eq

the destination hostname eq tcp service object

the purpose of the tcp destination eq https service

the purpose of the tcp destination eq imap4 service

the purpose of the tcp destination eq nntp service

the purpose of the tcp destination eq pop3 service

the purpose of the tcp destination eq smtp service

the purpose of the tcp destination eq telnet service

Outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_0 any object SVR

Outside_access_in list extended access allow TCPUDP of object-group a

Outside_access_in access-list extended ip any any idle state to allow

Internal_access_in list extended access allow TCPUDP of object-group a

Internal_access_in access-list extended ip any any idle state to allow

SPLIT_TUNNEL list standard access allowed 10.0.0.0 255.255.255.0

pager lines 24

Enable logging

timestamp of the record

exploitation forest-size of the buffer 16384

buffered logging critical

asdm of logging of information

Debugging trace record

exploitation forest flash-bufferwrap

record level of the rate-limit 1000 1 2

management of MTU 1500

MTU 1500 internal

Outside 1500 MTU

no failover

ICMP unreachable rate-limit 1 burst-size 1

ASDM image disk0: / asdm - 711.bin

don't allow no asdm history

ARP timeout 14400

no permit-nonconnected arp

!

the SVR object network

203.106.x.x static NAT (indoor, outdoor)

!

source of auto after the cessation of NAT (inside, outside) dynamic interface

Internal_access_in in interface internal access-group

Access-group Outside_access_in in interface outside

Route outside 0.0.0.0 0.0.0.0 203.106.23.97 1

Timeout xlate 03:00

Pat-xlate timeout 0:00:30

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

Floating conn timeout 0:00:00

dynamic-access-policy-registration DfltAccessPolicy

identity of the user by default-domain LOCAL

the ssh LOCAL console AAA authentication

LOCAL AAA authorization command

Enable http server

http 192.168.1.0 255.255.255.0 management

http authentication certificate management

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

No vpn sysopt connection permit

Crypto ipsec ikev2 ipsec-proposal OF

encryption protocol esp

Esp integrity sha - 1, md5 Protocol

Crypto ipsec ikev2 proposal ipsec 3DES

Esp 3des encryption protocol

Esp integrity sha - 1, md5 Protocol

Crypto ipsec ikev2 ipsec-proposal AES

Esp aes encryption protocol

Esp integrity sha - 1, md5 Protocol

Crypto ipsec ikev2 ipsec-proposal AES192

Protocol esp encryption aes-192

Esp integrity sha - 1, md5 Protocol

Crypto ipsec ikev2 AES256 ipsec-proposal

Protocol esp encryption aes-256

Esp integrity sha - 1, md5 Protocol

Crypto ipsec pmtu aging infinite - the security association

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF

card crypto Outside_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

Outside_map interface card crypto outside

Crypto ca trustpoint ASDM_TrustPoint0

Terminal registration

name of the object CN = ASA

Configure CRL

Crypto ca trustpoint Anyconnect_TrustPoint

registration auto

name of the object CN = ASA

anyconnect_rsa key pair

Configure CRL

Crypto ca trustpoint _SmartCallHome_ServerCA

Configure CRL

trustpool crypto ca policy

string encryption ca Anyconnect_TrustPoint certificates

IKEv2 crypto policy 1

aes-256 encryption

integrity sha

Group 2 of 5

FRP sha

second life 86400

IKEv2 crypto policy 10

aes-192 encryption

integrity sha

Group 2 of 5

FRP sha

second life 86400

IKEv2 crypto policy 20

aes encryption

integrity sha

Group 2 of 5

FRP sha

second life 86400

IKEv2 crypto policy 30

3des encryption

integrity sha

Group 2 of 5

FRP sha

second life 86400

IKEv2 crypto policy 40

the Encryption

integrity sha

Group 2 of 5

FRP sha

second life 86400

Crypto ikev2 activate out of service the customer port 443

Crypto ikev2 access remote trustpoint Anyconnect_TrustPoint

Telnet timeout 3

SSH 172.19.88.0 255.255.255.0 internal

SSH 0.0.0.0 0.0.0.0 outdoors

SSH timeout 15

Console timeout 0

management of 192.168.1.100 - 192.168.1.200 addresses dhcpd

enable dhcpd management

!

a basic threat threat detection

Statistics-list of access threat detection

no statistical threat detection tcp-interception

NTP server 119.110.97.148 prefer external source

SSL-trust outside Anyconnect_TrustPoint point

WebVPN

allow outside

AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1

AnyConnect image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 2

AnyConnect image disk0:/anyconnect-linux-2.5.2014-k9.pkg 3

AnyConnect profiles AnyConnect_client_profile disk0: / AnyConnect_client_profile.xml

AnyConnect enable

attributes of Group Policy DfltGrpPolicy

VPN-tunnel-Protocol ikev1, ikev2 ssl clientless ssl ipsec l2tp client

Split-tunnel-policy tunnelspecified

value of Split-tunnel-network-list SPLIT_TUNNEL

Group Policy 'GroupPolicy AnyConnect' internal

Group Policy attributes "GroupPolicy AnyConnect"

value of server WINS 172.19.88.11

value of server DNS 172.19.88.11

SSL VPN-tunnel-Protocol ikev2 client ssl clientless

WebVPN

AnyConnect value AnyConnect_client_profile type user profiles

attributes global-tunnel-group DefaultWEBVPNGroup

address pool AnyPool

tunnel-group "AnyConnect" type remote access

attributes global-tunnel-group "AnyConnect".

address pool AnyPool

strategy-group-by default "GroupPolicy AnyConnect"

tunnel-group "AnyConnect" webvpn-attributes

Group-alias "AnyConnect" activate

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

maximum message length automatic of customer

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the rsh

inspect the rtsp

inspect esmtp

inspect sqlnet

inspect the skinny

inspect sunrpc

inspect xdmcp

inspect the sip

inspect the netbios

inspect the tftp

Review the ip options

Hi Max,.

Please send me the output of 'see the anyconnect vpn-sessiondb' once connected with VPN.

And try to add the following configuration and see if that helps:

NAT (inside, outside) 1 static source NETWORK_OBJ_172.19.88.0_24 NETWORK_OBJ_172.19.88.0_24 static destination VPN-VPN-POOL no-proxy-arp-route search

And one more qusetion do you use split tunnel? If yes then you must make the following changes, because your split tunnel is incorrect, in the split tunnel, you have configured the address pool of vpn. Please make the following change:

no access list SPLIT_TUNNEL standards not allowed 10.0.0.0 255.255.255.0

Standard access list SPLIT_TUNNEL allow 172.19.88.0 255.255.255.0

Group Policy attributes "GroupPolicy AnyConnect"

Split-tunnel-policy tunnelspecified

value of Split-tunnel-network-list SPLIT_TUNNEL

Let me know if this can help, or if you have any questions, more about it.

Thank you

Jeet Kumar

Cannot access remote network by VPN Site to Site ASA

Hello everyone

First of all I must say that I have configured the VPN site-to site a million times before. Stuck with it. First of all I can't ping outside the interface of my ASA remote. Secondly, VPN is in place, but no connectivity between local networks

ASA local:
hostname gyd - asa
domain bct.az
activate the encrypted password of XeY1QWHKPK75Y48j
XeY1QWHKPK75Y48j encrypted passwd
names of
DNS-guard
!
interface GigabitEthernet0/0
Shutdown
nameif vpnswc
security-level 0
IP 10.254.17.41 255.255.255.248
!
interface GigabitEthernet0/1
Vpn-turan-Baku description
nameif outside Baku
security-level 0
IP 10.254.17.9 255.255.255.248
!
interface GigabitEthernet0/2
Vpn-ganja description
nameif outside-Ganja
security-level 0
IP 10.254.17.17 255.255.255.248
!
interface GigabitEthernet0/2.30
Description remote access
VLAN 30
nameif remote access
security-level 0
IP 85.*. *. * 255.255.255.0
!
interface GigabitEthernet0/3
Description BCT_Inside
nameif inside-Bct
security-level 100
IP 10.40.50.65 255.255.255.252
!
interface Management0/0
nameif management
security-level 100
IP 192.168.251.1 255.255.255.0
management only
!
boot system Disk0: / asa823 - k8.bin
passive FTP mode
DNS server-group DefaultDNS
name-server 192.168.1.3
domain bct.az
permit same-security-traffic intra-interface
object-group network obj - 192.168.121.0
object-group network obj - 10.40.60.0
object-group network obj - 10.40.50.0
object-group network obj - 192.168.0.0
object-group network obj - 172.26.0.0
object-group network obj - 10.254.17.0
object-group network obj - 192.168.122.0
object-group service obj-tcp-eq-22
object-group network obj - 10.254.17.18
object-group network obj - 10.254.17.10
object-group network obj - 10.254.17.26
access-list 110 scope ip allow a whole
NAT list extended access permit tcp any host 10.254.17.10 eq ssh
NAT list extended access permit tcp any host 10.254.17.26 eq ssh
access-list extended ip allowed any one sheep
icmp_inside list extended access permit icmp any one
icmp_inside of access allowed any ip an extended list
access list nat-ganja extended permit tcp any host 10.254.17.18 eq ssh
RDP list extended access permit tcp any host 192.168.45.3 eq 3389
rdp extended permitted any one ip access list
sheep-vpn access-list extended permits all ip 192.168.121.0 255.255.255.0
NAT-vpn-internet access-list extended ip 192.168.121.0 allow 255.255.255.0 any
NAT-vpn-internet access-list extended ip 172.26.0.0 allow 255.255.255.0 any
NAT-vpn-internet access-list extended ip 192.168.122.0 allow 255.255.255.0 any
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.40.60.0 255.255.255.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.40.50.0 255.255.255.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 192.168.0.0 255.255.0.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 172.26.0.0 255.255.255.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.254.17.0 255.255.255.0
GHC-ganja-internet access-list extended ip 192.168.45.0 allow 255.255.255.0 any
Standard access list Split_Tunnel_List allow 192.168.16.0 255.255.255.0
azans 192.168.69.0 ip extended access-list allow 255.255.255.0 any
permit inside_nat0_outbound to access extended list ip 192.168.0.0 255.255.0.0 192.168.121.0 255.255.255.0
permit inside_nat0_outbound to access extended list ip 192.168.0.0 255.255.0.0 192.168.80.0 255.255.255.0
pager lines 24
Enable logging
emblem of logging
recording of debug console
recording of debug trap
asdm of logging of information
Interior-Bct 192.168.1.27 host connection
flow-export destination inside-Bct 192.168.1.27 9996
vpnswc MTU 1500
outside Baku MTU 1500
outside-Ganja MTU 1500
MTU 1500 remote access
Interior-Bct MTU 1500
management of MTU 1500
IP local pool raccess 192.168.121.60 - 192.168.121.120 mask 255.255.255.0
IP local pool ssl 192.168.121.130 - 192.168.121.200 mask 255.255.255.0
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any outside Baku
ICMP allow access remotely
ICMP allow any interior-Bct
ASDM image disk0: / asdm - 621.bin
don't allow no asdm history
ARP timeout 14400
global (outside-Baku) 1 interface
global (outside-Ganja) interface 2
3 overall (RAS) interface
azans access-list NAT 3 (outside-Ganja)
NAT (remote access) 0 access-list sheep-vpn-city
NAT 3 list nat-vpn-internet access (remote access)
NAT (inside-Bct) 0-list of access inside_nat0_outbound
NAT (inside-Bct) 2-nat-ganja access list
NAT (inside-Bct) 1 access list nat
Access-group rdp on interface outside-Ganja
!
Router eigrp 2008
No Auto-resume
neighbor 10.254.17.10 interface outside Baku
neighbor 10.40.50.66 Interior-Bct interface
Network 10.40.50.64 255.255.255.252
Network 10.250.25.0 255.255.255.0
Network 10.254.17.8 255.255.255.248
Network 10.254.17.16 255.255.255.248
redistribute static
!
Access remote 0.0.0.0 0.0.0.0 85.*. *. * 1
Outside-Baku route 10.0.11.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 10.0.33.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 10.0.150.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 10.0.170.0 255.255.255.0 10.254.17.10 1
Route outside Baku 10.254.17.24 255.255.255.248 10.254.17.10 1
Route outside Baku 10.254.17.32 255.255.255.248 10.254.17.10 1
Route outside Baku 192.1.1.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 192.168.27.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 192.168.39.0 255.255.255.0 10.254.17.10 1
Route outside-Ganja 192.168.45.0 255.255.255.0 10.254.17.18 1
Route outside-Ganja 192.168.66.0 255.255.255.0 10.254.17.18 1
Route outside-Ganja 192.168.69.0 255.255.255.0 10.254.17.18 1
Outside-Baku route 192.168.80.0 255.255.255.0 10.254.17.11 1
Access remote 192.168.121.0 255.255.255.0 85.132.43.1 1
Route outside-Ganja 192.168.184.0 255.255.255.0 10.254.17.18 1
Route outside Baku 192.168.208.16 255.255.255.240 10.254.17.10 1
Route outside-Ganja 192.168.208.112 255.255.255.240 10.254.17.18 1
Route inside-Bct 192.168.254.0 255.255.255.0 10.40.50.66 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server protocol Ganymede GANYMEDE +.
AAA-server GANYMEDE (Interior-Bct) 192.168.1.8
key *.
AAA-server GANYMEDE (Interior-Bct) 192.168.22.46
key *.
RADIUS protocol AAA-server TACACS1
AAA-server TACACS1 (Interior-Bct) host 192.168.1.8
key *.
AAA-server TACACS1 (Interior-Bct) host 192.168.22.46
key *.
authentication AAA ssh console LOCAL GANYMEDE
Console to enable AAA authentication RADIUS LOCAL
Console Telnet AAA authentication RADIUS LOCAL
AAA accounting ssh console GANYMEDE
Console Telnet accounting AAA GANYMEDE
Enable http server
http 192.168.1.0 255.255.255.0 management
http 192.168.1.0 255.255.255.0 Interior-Bct
http 192.168.139.0 255.255.255.0 Interior-Bct
http 192.168.0.0 255.255.255.0 Interior-Bct
Survey community SNMP-server host inside-Bct 192.168.1.27
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
Crypto ipsec transform-set newset aes - esp esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac myset2
Crypto ipsec transform-set esp-3des esp-md5-hmac raccess
Crypto ipsec transform-set esp-3des esp-sha-hmac vpnclienttrans
Crypto ipsec transform-set vpnclienttrans transport mode
life crypto ipsec security association seconds 2147483646
Crypto ipsec kilobytes of life security-association 2147483646
raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map
correspondence address card crypto mymap 10 110
card crypto mymap 10 peers set 10.254.17.10
card crypto mymap 10 transform-set RIGHT
correspondence address card crypto mymap 20 110
card crypto mymap 20 peers set 10.254.17.11
mymap 20 transform-set myset2 crypto card
card crypto mymap interface outside Baku
correspondence address card crypto ganja 10 110
10 ganja crypto map peer set 10.254.17.18
card crypto ganja 10 transform-set RIGHT
card crypto interface outside-Ganja ganja
correspondence address card crypto vpntest 20 110
peer set card crypto vpntest 20 10.250.25.1
newset vpntest 20 transform-set card crypto
card crypto vpntest interface vpnswc
vpnclientmap 30 card crypto ipsec-isakmp dynamic dyn1
card crypto interface for remote access vpnclientmap
Crypto ca trustpoint ASDM_TrustPoint0
registration auto
name of the object CN = gyd - asa .az .bct
sslvpnkeypair key pair
Configure CRL
map of crypto DefaultCertificateMap 10 ca certificate

crypto isakmp identity address
ISAKMP crypto enable vpnswc
ISAKMP crypto enable outside-Baku
ISAKMP crypto enable outside-Ganja
crypto ISAKMP enable remote access
ISAKMP crypto enable Interior-Bct
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 20
preshared authentication
aes encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 40
preshared authentication
aes encryption
sha hash
Group 2
life 86400
Crypto isakmp nat-traversal 30
No vpn-addr-assign aaa
Telnet timeout 5
SSH 192.168.0.0 255.255.255.0 Interior-Bct
SSH timeout 35
Console timeout 0
priority queue outside Baku
queue-limit 2046
TX-ring-limit 254
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Server NTP 192.168.1.3
SSL encryption, 3des-sha1 rc4 - md5 aes128-sha1 sha1-aes256
SSL-trust point ASDM_TrustPoint0 to vpnlb-ip remote access
SSL-trust ASDM_TrustPoint0 remote access point
WebVPN
turn on remote access
SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 1 image
enable SVC
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
internal group ssl policy
attributes of group ssl policy
banner welcome to SW value
value of DNS-server 192.168.1.3
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
group-lock value SSL
WebVPN
value of the SPS URL-list
internal vpn group policy
attributes of vpn group policy
value of DNS-server 192.168.1.3
Protocol-tunnel-VPN IPSec l2tp ipsec
disable the PFS
BCT.AZ value by default-field
ssl VPN-group-strategy
WebVPN
value of the SPS URL-list
IPSec-attributes tunnel-group DefaultL2LGroup
ISAKMP retry threshold 20 keepalive 5
attributes global-tunnel-group DefaultRAGroup
raccess address pool
Group-RADIUS authentication server
Group Policy - by default-vpn
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
IPSec-attributes tunnel-group DefaultWEBVPNGroup
ISAKMP retry threshold 20 keepalive 5
tunnel-group 10.254.17.10 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.10
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
type SSL tunnel-group remote access
attributes global-group-tunnel SSL
ssl address pool
Authentication (remote access) LOCAL servers group
Group Policy - by default-ssl
certificate-use-set-name username
Group-tunnel SSL webvpn-attributes
enable SSL group-alias
Group-url https://85. *. *. * / activate
tunnel-group 10.254.17.18 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.18
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
tunnel-group 10.254.17.11 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.11
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
type tunnel-group DefaultSWITGroup remote access
attributes global-tunnel-group DefaultSWITGroup
raccess address pool
Group-RADIUS authentication server
Group Policy - by default-vpn
IPSec-attributes tunnel-group DefaultSWITGroup
pre-shared key *.
!
type of policy-card inspect dns migrated_dns_map_1
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the migrated_dns_map_1 dns
inspect the rsh
inspect the rtsp
inspect sqlnet
inspect sunrpc
inspect xdmcp
inspect the netbios
Review the ip options
class flow_export_cl
flow-export-type of event all the destination 192.168.1.27
class class by default
flow-export-type of event all the destination 192.168.1.27
Policy-map Voicepolicy
class voice
priority
The class data
police release 80000000
!
global service-policy global_policy
service-policy interface outside Baku Voicepolicy
context of prompt hostname

Cryptochecksum:4f35f975ba7a0c11f7f46dfd541d266f
: end
GYD - asa #.

ASA remote:
ASA Version 8.2 (3)
!
ciscoasa hostname
activate the encrypted password of XeY1QWHKPK75Y48j
2KFQnbNIdI.2KYOU encrypted passwd
names of
DNS-guard
!
interface Ethernet0/0
nameif inside
security-level 100
IP 192.168.80.14 255.255.255.0
!
interface Ethernet0/1
nameif outside
security-level 0
IP 10.254.17.11 255.255.255.248
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
nameif management
security-level 100
no ip address
management only
!
boot system Disk0: / asa823 - k8.bin
passive FTP mode
access-list 110 scope ip allow a whole
192.168.80.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.0.0 255.255.0.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
management of MTU 1500
Within 1500 MTU
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow all outside
ICMP allow any inside
ASDM image disk0: / asdm - 621.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside) 0 access-list sheep
Route outside 0.0.0.0 0.0.0.0 10.254.17.9 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.1.0 255.255.255.0 management
http 192.168.80.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
Crypto ipsec transform-set newset aes - esp esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac myset2
life crypto ipsec security association seconds 2147483646
Crypto ipsec kilobytes of life security-association 2147483646
correspondence address card crypto mymap 10 110
card crypto mymap 10 peers set 10.254.17.9
mymap 10 transform-set myset2 crypto card
mymap outside crypto map interface
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 20
preshared authentication
aes encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 40
preshared authentication
aes encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN

tunnel-group 10.254.17.9 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.9
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns migrated_dns_map_1
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the migrated_dns_map_1 dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname

Cryptochecksum:1c1ac60e2fb84f65269d15d53f27c21b
: end
ciscoasa # $

Still, I can't ping ASA remote outside from outside of the Local interface. And there is no connectivity between the 192.168.80.0 distance and local don't say 192.168.1.0. I have run out of ideas

Would appreciate any help. Thank you in advance...

If the tunnel is up (phase 1), but no traffic passing the best test is the following:

Add order management-access to the Interior , and then try to PING the intellectual property inside ASA counterpart.

inside x.x.x.x ping --> x.x.x.x is the IP of the ASA peer inside

The test above shows if the traffic passes through the tunnel (check encrypted/decrypted packets of sh cry ips its).

Test on both directions.

Please post the results.

Federico.

Newbie question: in what configuration file < flex: access remote destination > tags go?

I seem to have read the document integration spring/Blaze about 10 times, but I don't know where to put all my < flex: access remote-Ref destination = "yaddayaddaService" / > tags. I don't want annotation allows you to set these remote destinations.
Should it go in the spring configuration file that I use for the servlet of AMF endpoint (as specified by the contextConfigLocation parameter). Or they go to a high-level cross-servlet configuration file?
What is the usual way to deal with these?

Hello

The convention is to declare:

1 declare the Spring beans (for example yaddayaddaService) in the files specified by the parameter contextConfigLocation.

2. Add the Spring - Flex specific configuration (configure message agent, declare destinations) in WEB-INF\flex- servlet.xml, assuming that you have configured the model of Message Broker URL as follows in the web.xml file:


        Flex
        org.springframework.web.servlet.DispatcherServlet
        1



        Flex
        messagebroker / *.


The repository SVN BlazeDS/distribution contains the spring sample webapp (spring - samples.war) that you can watch as well.

Hope that helps.

Rohit

Our computer was accessed remotely this afternoon, how can we prevent this?

We have a Mac Mini, with OS X 10.6.8 using NetZero DSL as our internet provider and Firefox as your browser. Our computer was accessed remotely through LogMeIn (rescue), but it seems that the person or the group failed to hack into our computer. Are there settings in Firefox that could prevent this from happening in the future? Thank you...

Firefox is a web browser not a firewall.

I agree that it's more to do with your operating system and the LogMeIn software on ensuring that only you have access when you need to.

My camera iPhone 5s is accessed remotely? Whenever I use my phone torch ends up taking videos. Is it possible for a person to access my camera through the torch. We share the same Apple ID

My camera iPhone 5s is accessed remotely? Whenever I use my phone torch ends up taking videos. Is it possible for a person to access my camera through the torch. We share the same Apple ID

N °

but maybe you tap the camera icon (bottom-right) when you press the icon of the torch (with the other hand maybe?)

1920 router access remote vpn LDAP living

Hello

What is required for a router in 1920 use AnyConnect and/or also integrate with AD LDAP?

Currently, this router supports legacy clients and has these licenses:

Technology for the Module package license information: "c1900".

-----------------------------------------------------------------
Technology-technology-package technology
Course Type next reboot
------------------------------------------------------------------
IPBase ipbasek9 ipbasek9 Permanent
Security securityk9 Permanent securityk9
given none none none

The vpn to access remote client inherited integrate with AD LDAP?

Thank you.

As long as you are on IOS 15.3.3M3 or better, you have all the licenses you need for 3.1 AnyConnect run on your 1921.

The guide to directly connect your router to LDAP can be found here:

http://www.Cisco.com/c/en/us/TD/docs/iOS-XML/iOS/sec_usr_ldap/configuration/15-Mt/sec-usr-LDAP-15-Mt-book/sec_conf_ldap.html

Personally, I would avoid directly interfacing with LDAP, because it can be a complex arrangement. While it can be done, it's easier to have your router to connect to the NPS Microsoft via RADIUS server for your authentication.

2 VPN SITE to SITE with ACCESS REMOTE VPN

Hello

I have a 870 router c and I would like to put 2 different VPN SITE to SITE and access remote VPN (VPN CLIENTS) so is it possible to put 3 VPN in the router even if yes can u give me the steps or the sample configuration

Concerning

Thus, on the routers will be:

Cisco 2611:

LAN: 10.10.10.0/24

access-list 100 permit ip 10.10.10.0 0.0.0.255 10.10.20.0 0.0.0.255

access-list 100 permit ip 14.1.1.0 0.0.0.255 10.10.20.0 0.0.0.255--> VPNPOOL

!

10 ipsec-isakmp crypto map clientmap

defined by peer 172.18.124.199

match address 100

!

IP local pool ippool 14.1.1.1 14.1.1.254

!

access-list 120 allow ip 10.10.10.0 0.0.0.255 14.1.1.0 0.0.0.255

access-list 120 allow ip 10.10.20.0 0.0.0.255 14.1.1.0 0.0.0.255 --> NETWORK REMOTE

!

crypto ISAKMP client configuration group ra-customer

pool ippool

ACL 120

!

Please note that the configuration is incomplete, I added that relevant changes, you should bring to the allow clients of RA through the LAN-to-LAN tunnel, of course, the LAN-to-LAN settings should match to the other side of the tunnel that is mirror of ACL, NAT and so on.

HTH,

Portu.

On ASA 5505 VPN cannot access remote (LAN)

I have an ASA 5505 upward and running, all static NAT statements I need to forward ports to the internal services such as smtp, desktop remotely and it works very well, however I have set up an IPSEC vpn connection that authenticates to our DC and part works. However, after I connect and cannot ping anything on the local network or access services. I don't know what a NAT statement I have corrected. Here is the config. I really need to get this up and going tomorrow. Thanks for any help.

Tyler

Just remove the line of nat (outside) and ACL outside_nat0_outbound.

And talk about these statements:

IPSec-1 sysopt connection permit... (If it is disabled, you can check with sh run sysopt).

2, crypto isakmp nat traversal 10 or 20

3 no NAT ACL, mention your local subnets as the source and vpn client as the destination.

4, create the other ACL (ST) with different name and source and destination like no nat ACL.

5, then type nat (inside) 0 access-list sheep

6, in the dwgavpn group policy, talk to splittunnel tunnelspecified and mention the tunnel split ACL (ST).

Concerning

a public access remote vpn from an inside interface asa 5505

I'm trying to see if it is possible to accomplish what I am trying. I have an ASA 5505 with the following configuration.

1. There is an external connection, connected to the ISP. Let's say that it is 10.1.1.1/24 for ease. There is a remote VPN configuration as the access of people through this interface.

2. There's the inside network, which is the normal LAN. It's cable system in the office. to say that it is 172.20.0.1/24.

3. There is a wireless network on a VLAN separate called WLAN. It has an IP of 192.168.1.1/24. There is an ACL allowing traffic to that VLAN to the public internet.

Essentially, I would like users to be able to use the same VPN settings they use when connecting from outside of the Office when you are connected to WIFI.

Also, I would like that they can access public IP addresses that I have NAT would be to internal servers. In this way, they can use IP addresses when they use on the public internet.

Is this possible?

Hello

Well that's not going to be possible, the only thing you can really do is to activate the crypto map on the WLAN facing interface, by design, you cannot not access VPN, ping or manage the device on an interface which is not directly connected to you.

I hope this helps.

Mike

Help with access remotely for my husband who doesn't know a thing about computers! Laughing out loud

My husband has no idea of what she does on her laptop that I gave him, hes a truck driver and created our computers remotely with remote access earlier. He needs help setting up something, don't ask me what becausee it seems that I do not speak English it lol! He has no idea how find ip address or give me access (I instruct on how to give me remote access but he still could not understand)! Y at - it anyway to find my old connection (ip address) on my computer at home so I can send him an invitation to allow me on the laptop to help her. Can someone help me? I would be very appricate it! I would like to thank Krystal

My husband has no idea of what she does on her laptop that I gave him, hes a truck driver and created our computers remotely with remote access earlier. He needs help setting up something, don't ask me what becausee it seems that I do not speak English it lol! He has no idea how find ip address or give me access (I instruct on how to give me remote access but he still could not understand)! Y at - it anyway to find my old connection (ip address) on my computer at home so I can send him an invitation to allow me on the laptop to help her. Can someone help me? I would be very appricate it! I would like to thank Krystal

Try Windows Live Mesh... It works very well for remote access.

Problem with remote access VPN on ASA 5505

I currently have a problem of an ASA 5505 configuration to connect via VPN remote access by using the Cisco VPN Client 5.0.07.0440 under Windows 8 Pro x 64. The VPN client will prompt you for the user name and password during the connection process, but fails soon after.

The VPN client connects is as follows:

---------------------------------------------------------------------------------------------------------------------------------------

Cisco Systems VPN Client Version 5.0.07.0440

Copyright (C) 1998-2010 Cisco Systems, Inc.. All rights reserved.

Customer type: Windows, Windows NT

Running: 6.2.9200

2 15:09:21.240 11/12/12 Sev = Info/4 CM / 0 x 63100002

Start the login process

3 15:09:21.287 11/12/12 Sev = Info/4 CM / 0 x 63100004

Establish a secure connection

4 15:09:21.287 11/12/12 Sev = Info/4 CM / 0 x 63100024

Attempt to connect with the server "*." **. ***. *** »

5 15:09:21.287 11/12/12 Sev = Info/6 IKE/0x6300003B

Try to establish a connection with *. **. ***. ***.

6 15:09:21.287 11/12/12 Sev = Info/4 IKE / 0 x 63000001

From IKE Phase 1 negotiation

7 15:09:21.303 11/12/12 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) to *. **. ***. ***

8 15:09:21.365 11/12/12 Sev = Info/6 GUI/0x63B00012

Attributes of the authentication request is 6: 00.

9 15:09:21.334 11/12/12 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

10 15:09:21.334 11/12/12 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" ag="" (sa,="" ke,="" non,="" id,="" hash,="" vid(unity),="" vid(xauth),="" vid(dpd),="" vid(nat-t),="" nat-d,="" nat-d,="" vid(frag),="" vid(?))="" from="">

11 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000001

Peer is a compatible peer Cisco-Unity

12 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000001

Peer supports XAUTH

13 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000001

Peer supports the DPD

14 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000001

Peer supports NAT - T

15 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000001

Peer supports fragmentation IKE payloads

16 15:09:21.334 11/12/12 Sev = Info/6 IKE / 0 x 63000001

IOS Vendor ID successful construction

17 15:09:21.334 11/12/12 Sev = Info/4 IKE / 0 x 63000013

SENDING > ISAKMP OAK AG * (HASH, NOTIFY: NAT - D, NAT - D, VID (?), STATUS_INITIAL_CONTACT, VID (Unity)) to *. **. ***. ***

18 15:09:21.334 11/12/12 Sev = Info/6 IKE / 0 x 63000055

Sent a keepalive on the IPSec Security Association

19 15:09:21.334 11/12/12 Sev = Info/4 IKE / 0 x 63000083

IKE port in use - Local Port = 0xFBCE, Remote Port = 0 x 1194

20 15:09:21.334 11/12/12 Sev = Info/5 IKE / 0 x 63000072

Automatic NAT detection status:

Remote endpoint is NOT behind a NAT device

This effect is behind a NAT device

21 15:09:21.334 11/12/12 Sev = Info/4 CM/0x6310000E

ITS established Phase 1. 1 crypto IKE Active SA, 0 IKE SA authenticated user in the system

22 15:09:21.365 11/12/12 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

23 15:09:21.365 11/12/12 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">

24 15:09:21.365 11/12/12 Sev = Info/4 CM / 0 x 63100015

Launch application xAuth

25 15:09:21.474 11/12/12 Sev = Info/4 IPSEC / 0 x 63700008

IPSec driver started successfully

26 15:09:21.474 11/12/12 Sev = Info/4 IPSEC / 0 x 63700014

Remove all keys

27 15:09:27.319 11/12/12 Sev = Info/4 CM / 0 x 63100017

xAuth application returned

28 15:09:27.319 11/12/12 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***

29 15:09:27.365 11/12/12 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

30 15:09:27.365 11/12/12 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">

31 15:09:27.365 11/12/12 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***

32 15:09:27.365 11/12/12 Sev = Info/4 CM/0x6310000E

ITS established Phase 1. 1 crypto IKE Active SA, 1 IKE SA authenticated user in the system

33 15:09:27.365 11/12/12 Sev = Info/5 IKE/0x6300005E

Customer address a request from firewall to hub

34 15:09:27.365 11/12/12 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***

35 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

36 15:09:27.397 11/12/12 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">

37 15:09:27.397 11/12/12 Sev = Info/5 IKE / 0 x 63000010

MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS:, value = 192.168.2.70

38 15:09:27.397 11/12/12 Sev = Info/5 IKE / 0 x 63000010

MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK:, value = 255.255.255.0

39 15:09:27.397 11/12/12 Sev = Info/5 IKE / 0 x 63000010

MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (1):, value = 192.168.2.1

40 15:09:27.397 11/12/12 Sev = Info/5 IKE / 0 x 63000010

MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (2):, value = 8.8.8.8

41 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000D

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD:, value = 0x00000001

42 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000E

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN:, value = NCHCO

43 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000D

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS:, value = 0x00000000

44 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000E

MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc. ASA5505 Version 8.2 (5) built by manufacturers on Saturday, May 20, 11 16:00

45 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000D

MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT:, value = 0x00000001

46 15:09:27.397 11/12/12 Sev = Info/5 IKE/0x6300000D

MODE_CFG_REPLY: Attribute = received and by using the NAT - T port number, value = 0 x 00001194

47 15:09:27.397 11/12/12 Sev = Info/4 CM / 0 x 63100019

Data in mode Config received

48 15:09:27.412 11/12/12 Sev = Info/4 IKE / 0 x 63000056

Received a request from key driver: local IP = 192.168.2.70, GW IP = *. **. ***. remote IP address = 0.0.0.0

49 15:09:27.412 11/12/12 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK QM * (HASH, SA, NO, ID, ID) to *. **. ***. ***

50 15:09:27.444 11/12/12 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

51 15:09:27.444 11/12/12 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:status_resp_lifetime)="" from="">

52 15:09:27.444 11/12/12 Sev = Info/5 IKE / 0 x 63000045

Answering MACHINE-LIFE notify has value of 86400 seconds

53 15:09:27.444 11/12/12 Sev = Info/5 IKE / 0 x 63000047

This SA was already alive for 6 seconds, setting expiration 86394 seconds now

54 15:09:27.459 11/12/12 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

55 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:no_proposal_chosen)="" from="">

56 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000013

SEND to > ISAKMP OAK INFO *(HASH, DEL) to *. **. ***. ***

57 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000049

IPsec security association negotiation made scrapped, MsgID = CE99A8A8

58 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000017

Marking of IKE SA delete (I_Cookie = A3A341F1C7606AD5 R_Cookie = F1F403018625E924) reason = DEL_REASON_IKE_NEG_FAILED

59 15:09:27.459 11/12/12 Sev = Info/5 IKE/0x6300002F

Received packet of ISAKMP: peer = *. **. ***. ***

60 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000058

Received an ISAKMP for a SA message no assets, I_Cookie = A3A341F1C7606AD5 R_Cookie = F1F403018625E924

61 15:09:27.459 11/12/12 Sev = Info/4 IKE / 0 x 63000014

RECEIVING< isakmp="" oak="" info="" *(dropped)="" from="">

62 15:09:27.490 11/12/12 Sev = Info/4 IPSEC / 0 x 63700014

Remove all keys

63 15:09:30.475 11/12/12 Sev = Info/4 IKE/0x6300004B

IKE negotiation to throw HIS (I_Cookie = A3A341F1C7606AD5 R_Cookie = F1F403018625E924) reason = DEL_REASON_IKE_NEG_FAILED

64 15:09:30.475 11/12/12 Sev = Info/4 CM / 0 x 63100012

ITS phase 1 deleted before first Phase 2 SA is caused by "DEL_REASON_IKE_NEG_FAILED". Crypto 0 Active IKE SA, 0 IKE SA authenticated user in the system

65 15:09:30.475 11/12/12 Sev = Info/5 CM / 0 x 63100025

Initializing CVPNDrv

66 15:09:30.475 11/12/12 Sev = Info/6 CM / 0 x 63100046

Set indicator established tunnel to register to 0.

67 15:09:30.475 11/12/12 Sev = Info/4 IKE / 0 x 63000001

Signal received IKE to complete the VPN connection

68 15:09:30.475 11/12/12 Sev = Info/4 IPSEC / 0 x 63700014

Remove all keys

69 15:09:30.475 11/12/12 Sev = Info/4 IPSEC / 0 x 63700014

Remove all keys

70 15:09:30.475 11/12/12 Sev = Info/4 IPSEC / 0 x 63700014

Remove all keys

71 15:09:30.475 11/12/12 Sev = Info/4 IPSEC/0x6370000A

IPSec driver successfully stopped

---------------------------------------------------------------------------------------------------------------------------------------

The running configuration is the following (there is a VPN site-to-site set up as well at an another ASA 5505, but that works perfectly):

: Saved

:

ASA Version 8.2 (5)

!

hostname NCHCO

Select hTjwXz/V8EuTw9p9 of encrypted password

hTjwXz/V8EuTw9p9 of encrypted passwd

names of

description of NCHCO name 192.168.2.0 City offices

name 192.168.2.80 VPN_End

name 192.168.2.70 VPN_Start

!

interface Ethernet0/0

switchport access vlan 2

Speed 100

full duplex

!

interface Ethernet0/1

!

interface Ethernet0/2

!

interface Ethernet0/3

!

interface Ethernet0/4

!

interface Ethernet0/5

!

interface Ethernet0/6

!

interface Ethernet0/7

!

interface Vlan1

nameif inside

security-level 100

IP 192.168.2.1 255.255.255.0

!

interface Vlan2

nameif outside

security-level 0

IP address **. ***. 255.255.255.248

!

boot system Disk0: / asa825 - k8.bin

passive FTP mode

access extensive list ip NCHCO 255.255.255.0 outside_nat0_outbound allow 192.168.1.0 255.255.255.0

access extensive list ip NCHCO 255.255.255.0 inside_nat0_outbound allow 192.168.1.0 255.255.255.0

inside_nat0_outbound list of allowed ip extended access all 192.168.2.64 255.255.255.224

access extensive list ip NCHCO 255.255.255.0 outside_1_cryptomap allow 192.168.1.0 255.255.255.0

access extensive list ip NCHCO 255.255.255.0 outside_1_cryptomap_1 allow 192.168.1.0 255.255.255.0

Standard access list LAN_Access allow NCHCO 255.255.255.0

LAN_Access list standard access allowed 0.0.0.0 255.255.255.0

pager lines 24

Enable logging

asdm of logging of information

Within 1500 MTU

Outside 1500 MTU

mask of VPN_Pool VPN_Start VPN_End of local pool IP 255.255.255.0

ICMP unreachable rate-limit 1 burst-size 1

ASDM image disk0: / asdm - 645.bin

don't allow no asdm history

ARP timeout 14400

Global 1 interface (outside)

NAT (inside) 0-list of access inside_nat0_outbound

NAT (inside) 1 0.0.0.0 0.0.0.0

NAT (outside) 0-list of access outside_nat0_outbound

Route outside 0.0.0.0 0.0.0.0 74.219.208.49 1

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

Floating conn timeout 0:00:00

dynamic-access-policy-registration DfltAccessPolicy

network-acl outside_nat0_outbound

WebVPN

SVC request to enable default svc

Enable http server

http 192.168.1.0 255.255.255.0 inside

http *. **. ***. 255.255.255.255 outside

http 74.218.158.238 255.255.255.255 outside

http NCHCO 255.255.255.0 inside

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown cold start

Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

Crypto ipsec transform-set esp-3des esp-sha-hmac l2tp-transform

Crypto ipsec transform-set l2tp-transformation mode transit

Crypto ipsec transform-set vpn-transform esp-aes-256 esp-sha-hmac

Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA

Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA

Crypto ipsec transform-set esp-3des esp-md5-hmac TRANS_ESP_3DES_MD5

Crypto ipsec transform-set transit mode TRANS_ESP_3DES_MD5

Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

life crypto ipsec security association seconds 28800

Crypto ipsec kilobytes of life - safety 4608000 association

crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

crypto dynamic-map dyn-map 10 set pfs Group1

crypto dynamic-map dyn-map transform 10-set, vpn l2tp-transformation-transformation

dynamic-map encryption dyn-map 10 value reverse-road

Crypto-map dynamic outside_dyn_map 20 game of transformation-TRANS_ESP_3DES_MD5

card crypto outside_map 1 match address outside_1_cryptomap

card crypto outside_map 1 set pfs Group1

peer set card crypto outside_map 1 74.219.208.50

card crypto outside_map 1 set of transformation-ESP-3DES-SHA

map outside_map 20-isakmp ipsec crypto dynamic outside_dyn_map

outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

outside_map interface card crypto outside

inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

inside crypto map inside_map interface

card crypto vpn-map 1 match address outside_1_cryptomap_1

card crypto vpn-card 1 set pfs Group1

set vpn-card crypto map peer 1 74.219.208.50

card crypto vpn-card 1 set of transformation-ESP-3DES-SHA

dynamic vpn-map 10 dyn-map ipsec isakmp crypto map

crypto isakmp identity address

crypto ISAKMP allow inside

crypto ISAKMP allow outside

crypto ISAKMP policy 10

preshared authentication

3des encryption

md5 hash

Group 2

life 86400

crypto ISAKMP policy 15

preshared authentication

aes-256 encryption

sha hash

Group 2

life 86400

crypto ISAKMP policy 35

preshared authentication

3des encryption

sha hash

Group 2

life 86400

crypto ISAKMP ipsec-over-tcp port 10000

enable client-implementation to date

Telnet 192.168.1.0 255.255.255.0 inside

Telnet NCHCO 255.255.255.0 inside

Telnet timeout 5

SSH 192.168.1.0 255.255.255.0 inside

SSH NCHCO 255.255.255.0 inside

SSH timeout 5

Console timeout 0

dhcpd address 192.168.2.150 - 192.168.2.225 inside

dhcpd dns 216.68.4.10 216.68.5.10 interface inside

lease interface 64000 dhcpd inside

!

a basic threat threat detection

Statistics-list of access threat detection

no statistical threat detection tcp-interception

WebVPN

internal DefaultRAGroup group strategy

attributes of Group Policy DefaultRAGroup

value of server DNS 192.168.2.1

Protocol-tunnel-VPN IPSec l2tp ipsec

nchco.local value by default-field

attributes of Group Policy DfltGrpPolicy

value of server DNS 192.168.2.1

Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

allow password-storage

enable IPSec-udp

enable dhcp Intercept 255.255.255.0

the address value VPN_Pool pools

internal NCHVPN group policy

NCHVPN group policy attributes

value of 192.168.2.1 DNS Server 8.8.8.8

Protocol-tunnel-VPN IPSec l2tp ipsec

value by default-field NCHCO

admin LbMiJuAJjDaFb2uw encrypted privilege 15 password username

username privilege 15 encrypted password yB1lHEVmHZGj5C2Z 8njferg

username, encrypted NCHvpn99 QhZZtJfwbnowceB7 password

attributes global-tunnel-group DefaultRAGroup

address (inside) VPN_Pool pool

address pool VPN_Pool

authentication-server-group (inside) LOCAL

authentication-server-group (outside LOCAL)

LOCAL authority-server-group

authorization-server-group (inside) LOCAL

authorization-server-group (outside LOCAL)

Group Policy - by default-DefaultRAGroup

band-Kingdom

band-band

IPSec-attributes tunnel-group DefaultRAGroup

pre-shared key *.

NOCHECK Peer-id-validate

tunnel-group DefaultRAGroup ppp-attributes

No chap authentication

no authentication ms-chap-v1

ms-chap-v2 authentication

tunnel-group DefaultWEBVPNGroup ppp-attributes

PAP Authentication

ms-chap-v2 authentication

tunnel-group 74.219.208.50 type ipsec-l2l

IPSec-attributes tunnel-group 74.219.208.50

pre-shared key *.

type tunnel-group NCHVPN remote access

attributes global-tunnel-group NCHVPN

address pool VPN_Pool

Group Policy - by default-NCHVPN

IPSec-attributes tunnel-group NCHVPN

pre-shared key *.

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

maximum message length automatic of customer

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the rsh

inspect the rtsp

inspect esmtp

inspect sqlnet

inspect the skinny

inspect sunrpc

inspect xdmcp

inspect the sip

inspect the netbios

inspect the tftp

Review the ip options

!

global service-policy global_policy

context of prompt hostname

no remote anonymous reporting call

Cryptochecksum:15852745977ff159ba808c4a4feb61fa

: end

ASDM image disk0: / asdm - 645.bin

ASDM VPN_Start 255.255.255.255 inside location

ASDM VPN_End 255.255.255.255 inside location

don't allow no asdm history

Anyone have any idea why this is happening?

Thank you!

Add, crypto dynamic-map outside_dyn_map 20 value reverse-road.

With respect,

Safwan

Access remote vpn connects to the 5505 but cannot ping servers

I have a cisco 5505 and trying to set it up with 6.4 AMPS.

My vpn client connects ok to the network but I'm unable to reach one of the servers.

I'm sure it's a simple configuration issue, as I don't have much experience with Cisco Configuration.

Any suggestions on where to find would be very appreciated.

Thanks in advance

Graham

Hi Graham,

Please, add the following command:

Inside_nat0_outbound to access extended list ip 192.168.100.0 allow 255.255.255.0 192.168.100.0 255.255.255.0

Thank you.

Portu.

Access remote VPN, no split tunneling, internet access. Translation NAT problem

Hi all, I'm new to the forum. I have a Cisco ASA 5505 with confusing (to me) question NAT.

Unique external IP (outside interface) with several translations of NAT static object to allow the redirection of port of various internal devices. The configuration worked smoothly during the past years.

Recently, I configured a without the split tunneling VPN remote access and access to the internet and noticed yesterday that my port forwarding has stopped working.

I reviewed the new rules for the VPN NAT and found the culprit.

I've been reviewing the rules again and again, and all I can think about and interpret it, I don't know how this rule affects the port forwarding on the device or how to fix.

Here's the NAT rules, I have in place: ('inactive' rule is the culprit. Once I have turn on this rule, the port forwarding hits a wall)

NAT (inside, outside) static source any any static destination VPN_Subnet VPN_Subnet non-proxy-arp-search to itinerary
NAT (outside, outside) static source VPN_Subnet VPN_Subnet VPN_Subnet VPN_Subnet non-proxy-arp-search of route static destination
NAT (outside, outside) source VPN_Subnet dynamic interface inactive
!
network obj_any object
NAT dynamic interface (indoor, outdoor)
network of the XXX_HTTP object
NAT (inside, outside) interface static tcp www www service
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 1

Any help would be appreciated.

Try changing the nat rule to VPN_Subnet interface of nat (outside, outside) the after-service automatic dynamic source

With respect,

Safwan

Help access remote in a 5505

Similar Questions

Maybe you are looking for