Router Cisco client VPN SPlit tunnel does not work
Hello!
I have configured the Cisco VPN CLient on a 2821 router, and it works fine.
I could access the inside resourses normally >
the problem is that when I connect with VPN I lost internet connectivity?
What wrong with my setup?
Below the current configuration of the router.
Kind regards!
CISCO2821 #sh run
Building configuration...
Current configuration: 5834 bytes
!
version 12.4
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
hostname CISCO2821
!
boot-start-marker
start the flash c2800nm-adventerprisek9 - mz.124 - 20.T.bin system
boot-end-marker
!
forest-meter operation of syslog messages
logging buffered 51200 warnings
!
AAA new-model
!
!
connection local VPN-LOCAL-AUTHENTIC AAA authentication
local AAA authorization network VPN-LOCAL-AUTHOR
!
!
AAA - the id of the joint session
!
dot11 syslog
IP source-route
!
!
IP cef
!
!
"yourdomain.com" of the IP domain name
8.8.8.8 IP name-server
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
!
!
voice-card 0
No dspfarm
!
!
username secret privilege 0 vpn 5 $1$ tCf1$ XAxQWtDRYdfy9g3JpVSvZ.
Archives
The config log
hidekeys
!
!
crypto ISAKMP policy 44
BA aes
preshared authentication
Group 2
life 44444
!
ISAKMP crypto group configuration of VPN client
key VPNVPNVPN
VPN-pool
ACL VPN-ACL-SPLIT
Max-users 5000
!
!
ISAKMP crypto ISAKMP-VPN-profile
identity VPN group match
list of authentication of client VPN-LOCAL-AUTHENTIC
VPN-LOCAL-AUTHOR of ISAKMP authorization list.
client configuration address respond
Configuration of VPN client group
virtual-model 44
!
!
Crypto ipsec transform-set VPN - SET esp - aes esp-sha-hmac
!
Crypto ipsec VPN-profile
transformation-VPN-SET game
Set isakmp VPN ISAKMP-PROFILE
!
!
interface GigabitEthernet0/0
IP 192.168.2.214 255.255.255.0
NAT outside IP
IP virtual-reassembly
IP tcp adjust-mss 1412
automatic duplex
automatic speed
!
interface GigabitEthernet0/1
IP 192.168.1.1 255.255.255.0
IP nat inside
IP virtual-reassembly
IP tcp adjust-mss 1412
automatic duplex
automatic speed
!
interface FastEthernet0/0/0
no ip address
Shutdown
automatic duplex
automatic speed
!
type of interface virtual-Template44 tunnel
IP unnumbered GigabitEthernet0/0
ipv4 ipsec tunnel mode
Tunnel ipsec VPN-PROFILE protection profile
!
interface Dialer0
no ip address
IP mtu 1452
IP virtual-reassembly
Shutdown
!
local pool IP VPN-POOL 192.168.1.150 192.168.1.250
IP forward-Protocol ND
IP http server
IP 8081 http port
23 class IP http access
local IP http authentication
no ip http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
!
!
IP nat inside source list ACL - NAT interface GigabitEthernet0/0 overload
!
IP access-list standard ACL-TELNET
allow a
!
extended ACL - NAT IP access list
ip permit 192.168.1.0 0.0.0.255 any
IP extended ACL-VPN-SPLIT access list
ip permit 192.168.1.0 0.0.0.255 192.168.1.0 0.0.0.255
scope of access to IP-VPN-ACL-SPLIT list
!
control plan
!
exec banner ^ C
% Warning of password expiration.
-----------------------------------------------------------------------
Professional configuration Cisco (Cisco CP) is installed on this device
and it provides the default username "cisco" single use. If you have
already used the username "cisco" to connect to the router and your IOS image
supports the option "unique" user, that user name is already expired.
You will not be able to connect to the router with the username when you leave
This session.
It is strongly recommended that you create a new user name with a privilege level
15 using the following command.
username
Replace
use. ----------------------------------------------------------------------- Line con 0 exec-timeout 0 0 Synchronous recording line to 0 line vty 0 4
ACL-TELNET access class in
exec-timeout 30 0
privilege level 15
Synchronous recording
transport input telnet ssh
line vty 5 15
ACL-TELNET access class in
exec-timeout 30 0
privilege level 15
Synchronous recording
transport input telnet ssh
line vty 16 988
ACL-TELNET access class in
exec-timeout 30 0
Synchronous recording
transport input telnet ssh
!
Scheduler allocate 20000 1000
end
CISCO2821 #.
I think that you made a mistake with your ACL name. the ACL applied is "VPN-ACL-SPLIT" which is an empty ACL. You must switch to that of "ACL-VPN-SPLIT" that has the entry "ip 192.168.1.0 allow 0.0.0.255 192.168.1.0 0.0.0.255" inside.
Tags: Cisco Network
Similar Questions
-
Hello
First of all - thanks to all who post here. I often browse the forums and search for help here and its very useful, so a big pat on the back for all who contribute. My first post, so here goes...
I've got my ASA 5505 v8.2 configured to allow the AnyConnect. This works. Client can connect and access remote systems via VPN. What causes me a massive headache, is the customer loses internet connectivity. I played a bit with my config a bit so what I am about to post that I know for sure is incorrect, but any help is greatly appreciated.
Notes
1. the router was set up for a VPN site to site standard that is no longer functional, but as you can see all the settings are always in the router.
2. the router also a DMZ configuration has to allow access to the internet with the help of the DMZ to some customers
CONFIGURATION:
ASA Version 8.2 (5)
!
hostname MYHOST
activate mUUvr2NINofYuSh2 encrypted password
UNDrnIuGV0tAPtz2 encrypted passwd
names of
name x.x.x.x LIKES-SD
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
switchport access vlan 7
!
interface Vlan1
nameif inside
security-level 100
192.168.101.1 IP address 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP x.x.x.x 255.255.0.0
!
interface Vlan7
prior to interface Vlan1
nameif DMZ
security-level 20
IP 137.57.183.1 255.255.255.0
!
passive FTP mode
clock timezone STD - 7
the obj_any_dmz object-group network
10 extended access-list allow ip 192.168.25.0 255.255.255.0 192.168.6.0 255.255.255.0
permit access ip host x.x.x.x 192.168.25.0 extended list no_nat 255.255.25 5.0
tunneling split list of permitted access standard 192.168.101.0 255.255.255.0
192.168.101.0 IP Access-list extended sheep 255.255.255.0 allow all
pager lines 24
Enable logging
debug logging in buffered memory
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
MTU 1500 DMZ
mask 192.168.101.125 - 192.168.101.130 255.255.255.0 IP local pool Internal_Range
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global interface 10 (external)
NAT (inside) 0-list of access no_nat
NAT (inside) 1 access-list sheep
NAT (DMZ) 10 137.57.183.0 255.255.255.0
Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
Route inside 192.168.8.0 255.255.255.0 192.168.101.2 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
http server enable 64000
http 0.0.0.0 0.0.0.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-aes-256 batus, esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
correspondence address card crypto 100 10 batus
crypto batus 100 peer LIKES-SD card game
batus batus 100 transform-set card crypto
batus outside crypto map interface
Crypto ca trustpoint ASDM_TrustPoint1
registration auto
name of the object CN = MYHOST
ClientX_cert key pair
Configure CRL
string encryption ca ASDM_TrustPoint1 certificates
certificate 0f817951
308201e7 a0030201 30820150 0202040f 0d06092a 81795130 864886f7 0d 010105
05003038 31173015 06035504 03130e41 494d452d 56504e2d 42415455 53311d 30
1b06092a 864886f7 0d 010902 160e4149 4d452d56 504e2d42 41545553 301e170d
31333036 32373137 32393335 5a170d32 33303632 35313732 3933355a 30383117
30150603 55040313 0e41494d 452-5650 4e2d4241 54555331 1d301b06 092 d has 8648
86f70d01 0902160e 41494d 45 2d56504e 424154 55533081 9f300d06 092 2d has 8648
86f70d01 01010500 03818d 30818902 00 818100c 9 ff840bf4 cfb8d394 2 c 940430
1887f25a 49038aa0 1299cf10 bda2a436 227dcdbf f1c5566b c35c2f19 8b3514d3
4e24f5b1 c8840e8c 60e2b39d bdc0082f 08cce525 97ffefba d42bb087 81b9adb9
db0a8b2f b643e651 d17cd6f8 f67297f2 d785ef46 c3acbb39 615e1ef1 23db072c
783fe112 acd6dc80 dc38e94b 6e56fe94 d59d5d02 03010001 300 d 0609 2a 864886
8181007e f70d0101 05050003 29e90ea0 e337976e 9006bc02 402fd58a a1d30fe8
b2c1ab49 a1828ee0 488d1d2f 1dc5d150 3ed85f09 54f099b2 064cd 622 dc3d3821
fca46c69 62231fd2 6e396cd1 7ef586f9 f41205af c2199174 3c5ee887 42b684c9
7f4d2045 4742adb5 d70c3805 4ad13191 8d802bbc b2bcd8c7 8eec111b 761d89f3
63ebd49d 30dd06f4 e0fa25
quit smoking
crypto ISAKMP allow outside
crypto ISAKMP policy 40
preshared authentication
aes-256 encryption
sha hash
Group 5
life 86400
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 inside
SSH 0.0.0.0 0.0.0.0 DMZ
SSH timeout 10
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
SSL encryption rc4 - md5, rc4-aes128-sha1 aes256-3des-sha1 sha1 sha1
SSL-trust outside ASDM_TrustPoint1 point
WebVPN
allow outside
SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 1 image
enable SVC
internal ClientX_access group strategy
attributes of Group Policy ClientX_access
VPN-tunnel-Protocol svc
Split-tunnel-network-list value split tunneling
access.local value by default-field
the address value Internal_Range pools
IPv6 address pools no
WebVPN
SVC mtu 1406
generate a new key SVC time no
SVC generate a new method ssl key
username privilege 15 encrypted password ykAxQ227nzontdIh ClientX
ClientX username attributes
VPN-group-policy ClientX_access
type of service admin
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group ipsec-attributes x.x.x.x
pre-shared key *.
tunnel-group ClientX type remote access
attributes global-tunnel-group ClientX
address pool Internal_Range
Group Policy - by default-ClientX_access
type tunnel-group SSLClientProfile remote access
attributes global-tunnel-group SSLClientProfile
Group Policy - by default-ClientX_access
type tunnel-group ClientX_access remote access
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:e7d92a387d1c5f07e14b3c894d159ec1
: end
-----------------------
Thanks for any help!
In your group strategy, you specified the ACLs that should be used for split Tunneling, but you forgot to change the policy, so the ASA always uses tunnel-all. Here's what you'll need:
attributes of Group Policy ClientX_access
Split-tunnel-network-list value split tunneling
Split-tunnel-policy tunnelspecified
--
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni -
The HP Client Manager Security extension does not work
I have a red shield on the top right of my address bar saying"
The HP Client Security Manager extension does not work because the HP Client Security Manager plug-in has not been activated.Open the HP Client Security Manager Console browser integration user Page for additional instructions.How can I find a user control panel browser integration page? do not see it anywhere? help needed please thanks Bill
Hello
Unfortunately, you may have to contact HP support for more help:
Kind regards
-
Cisco WLC 2504 internal DHCP does not work properly
Hi all
I m trials with a Cisco WLC 2504 and some APs of 1832. I set up a DHCP scope on the interface of the controller with 2
a large number of different configurations, but the DHCP protocol does not work and Don t Access Point to obtain an IP address. My first question: is it possible to do DHCP for Access Points or only for wireless clients?
These are my interfaces:
Interface of the PA-Manager:
My DHCP scope:
Advanced DHCP:
I forgot something? Is there anyone using DHCP for its access points?
Thank you!
Hello
On Cisco WLC internal DHCP, you can add the option 43 to say where APs must register. In this case, they will try to resolve the DNS CISCO-CAPWAP-CONTROLLER or CISCO-LWAPP entry.
Let me explain briefly how AP-Manager works on WLC:
- Boots of Access Point and sends a discovery request to the management interface of the controller using the intellectual property you configured as DHCP Option 43 (as described above, it can be resolved by the DNS entry)
- Controller, sends it a response discovered that contains the name of the system, addresses AP-Manager, the number of access points already connected to each interface AP-Manager and the overall capacity of the controller.
- Joints access point controller using the less loaded interface AP Manager.
With this, every AP Manager must have a good configured interface and be connected to a different port, no LAG.
I drop a post here sometimes there is which might help:
https://supportforums.Cisco.com/document/118311/configuring-multiple-AP-...
Thank you
PS: Please do not forget to rate and score as correct answer if this answered your question
-
Hi all
We have an IPSec tunnel that does not work. I think that Phase 2 is not established but I don't know why.
Add the output and the newspaper.
Thanks for your help
ASA-VPN-PRI/act/pri # sh crypto isakmp his
!
13 peer IKE: 91.209.243.5
Type: L2L role: answering machine
Generate a new key: no State: MM_ACTIVE!
ASA-VPN-PRI/act/pri # sh crypto isakmp his | include the 91.209.243.5
12 peer IKE: 91.209.243.5
ASA-VPN-PRI/act/pri #.ASA-VPN-PRI/act/pri # sh crypto ipsec his | include the 91.209.243.5
ASA-VPN-PRI/act/pri #.7. December 17, 2014 | 15: 40:48 | 713236 | IP = 91.209.243.5, IKE_DECODE SEND Message (msgid = c516994b) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84
7. December 17, 2014 | 15: 40:48 | 715046 | Group = 91.209.243.5, IP = 91.209.243.5, build payloads of hash qm
7. December 17, 2014 | 15: 40:48 | 715046 | Group = 91.209.243.5, IP = 91.209.243.5, payload of empty hash construction
7. December 17, 2014 | 15: 40:48 | 715036 | Group = 91.209.243.5, IP = 91.209.243.5, sending persistent type DPD R-U-HERE-ACK (seq number 0x7d6c)
7. December 17, 2014 | 15: 40:48 | 715075 | Group = 91.209.243.5, IP = 91.209.243.5, received persistent type DPD R-U-LÀ (seq number 0x7d6c)
7. December 17, 2014 | 15: 40:48 | 715047 | Group = 91.209.243.5, IP = 91.209.243.5, processing notify payload
7. December 17, 2014 | 15: 40:48 | 715047 | Group = 91.209.243.5, IP = 91.209.243.5, payload of hash of treatment
7. December 17, 2014 | 15: 40:48 | 713236 | IP = 91.209.243.5, IKE_DECODE RECEIPT Message (msgid = 29bf4142) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84
7. December 17, 2014 | 15: 40:43 | 713236 | IP = 91.209.243.5, IKE_DECODE SEND Message (msgid = b72ddf0a) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84
7. December 17, 2014 | 15: 40:43 | 715046 | Group = 91.209.243.5, IP = 91.209.243.5, build payloads of hash qm
7. December 17, 2014 | 15: 40:43 | 715046 | Group = 91.209.243.5, IP = 91.209.243.5, payload of empty hash construction
7. December 17, 2014 | 15: 40:43 | 715036 | Group = 91.209.243.5, IP = 91.209.243.5, sending persistent type DPD R-U-HERE-ACK (seq number 0x7d6b)
7. December 17, 2014 | 15: 40:43 | 715075 | Group = 91.209.243.5, IP = 91.209.243.5, received persistent type DPD R-U-LÀ (seq number 0x7d6b)
7. December 17, 2014 | 15: 40:43 | 715047 | Group = 91.209.243.5, IP = 91.209.243.5, processing notify payload
7. December 17, 2014 | 15: 40:43 | 715047 | Group = 91.209.243.5, IP = 91.209.243.5, payload of hash of treatment
7. December 17, 2014 | 15: 40:43 | 713236 | IP = 91.209.243.5, IKE_DECODE RECEIPT Message (msgid = ae5305df) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84
7. December 17, 2014 | 15: 40:38 | 713236 | IP = 91.209.243.5, IKE_DECODE SEND Message (msgid = b796798d) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84
7. December 17, 2014 | 15: 40:38 | 715046 | Group = 91.209.243.5, IP = 91.209.243.5, build payloads of hash qm
7. December 17, 2014 | 15: 40:38 | 715046 | Group = 91.209.243.5, IP = 91.209.243.5, payload of empty hash construction
7. December 17, 2014 | 15: 40:38 | 715036 | Group = 91.209.243.5, IP = 91.209.243.5, sending persistent type DPD R-U-HERE-ACK (seq number 0x7d6a)
7. December 17, 2014 | 15: 40:38 | 715075 | Group = 91.209.243.5, IP = 91.209.243.5, received persistent type DPD R-U-LÀ (seq number 0x7d6a)
7. December 17, 2014 | 15: 40:38 | 715047 | Group = 91.209.243.5, IP = 91.209.243.5, processing notify payload
7. December 17, 2014 | 15: 40:38 | 715047 | Group = 91.209.243.5, IP = 91.209.243.5, payload of hash of treatment
7. December 17, 2014 | 15: 40:38 | 713236 | IP = 91.209.243.5, IKE_DECODE RECEIPT Message (msgid = 98241c 63) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84
7. December 17, 2014 | 15: 40:33 | 713236 | IP = 91.209.243.5, IKE_DECODE SEND Message (msgid = e233621d) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84
7. December 17, 2014 | 15: 40:33 | 715046 | Group = 91.209.243.5, IP = 91.209.243.5, build payloads of hash qm
7. December 17, 2014 | 15: 40:33 | 715046 | Group = 91.209.243.5, IP = 91.209.243.5, payload of empty hash construction
7. December 17, 2014 | 15: 40:33 | 715036 | Group = 91.209.243.5, IP = 91.209.243.5, sending persistent type DPD R-U-HERE-ACK (seq number 0x7d69)
7. December 17, 2014 | 15: 40:33 | 715075 | Group = 91.209.243.5, IP = 91.209.243.5, received persistent type DPD R-U-LÀ (seq number 0x7d69)
7. December 17, 2014 | 15: 40:33 | 715047 | Group = 91.209.243.5, IP = 91.209.243.5, processing notify payload
7. December 17, 2014 | 15: 40:33 | 715047 | Group = 91.209.243.5, IP = 91.209.243.5, payload of hash of treatment
7. December 17, 2014 | 15: 40:33 | 713236 | IP = 91.209.243.5, IKE_DECODE RECEIPT Message (msgid = 36ecdf6a) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84
7. December 17, 2014 | 15: is.40:28 | 713236 | IP = 91.209.243.5, IKE_DECODE SEND Message (msgid = cb1b978d) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84
7. December 17, 2014 | 15: is.40:28 | 715046 | Group = 91.209.243.5, IP = 91.209.243.5, build payloads of hash qm
7. December 17, 2014 | 15: is.40:28 | 715046 | Group = 91.209.243.5, IP = 91.209.243.5, payload of empty hash construction
7. December 17, 2014 | 15: is.40:28 | 715036 | Group = 91.209.243.5, IP = 91.209.243.5, sending persistent type DPD R-U-HERE-ACK (seq number 0x7d68)
7. December 17, 2014 | 15: is.40:28 | 715075 | Group = 91.209.243.5, IP = 91.209.243.5, received persistent type DPD R-U-LÀ (seq number 0x7d68)
7. December 17, 2014 | 15: is.40:28 | 715047 | Group = 91.209.243.5, IP = 91.209.243.5, processing notify payload
7. December 17, 2014 | 15: is.40:28 | 715047 | Group = 91.209.243.5, IP = 91.209.243.5, payload of hash of treatment
7. December 17, 2014 | 15: is.40:28 | 713236 | IP = 91.209.243.5, IKE_DECODE RECEIPT Message (msgid = f25bcdb5) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84
7. December 17, 2014 | 15: 40:23 | 713236 | IP = 91.209.243.5, IKE_DECODE SEND Message (msgid = 32bca075) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84
7. December 17, 2014 | 15: 40:23 | 715046 | Group = 91.209.243.5, IP = 91.209.243.5, build payloads of hash qm
7. December 17, 2014 | 15: 40:23 | 715046 | Group = 91.209.243.5, IP = 91.209.243.5, payload of empty hash construction
7. December 17, 2014 | 15: 40:23 | 715036 | Group = 91.209.243.5, IP = 91.209.243.5, sending persistent type DPD R-U-HERE-ACK (seq number 0x7d67)
7. December 17, 2014 | 15: 40:23 | 715075 | Group = 91.209.243.5, IP = 91.209.243.5, received persistent type DPD R-U-LÀ (seq number 0x7d67)
7. December 17, 2014 | 15: 40:23 | 715047 | Group = 91.209.243.5, IP = 91.209.243.5, processing notify payload
7. December 17, 2014 | 15: 40:23 | 715047 | Group = 91.209.243.5, IP = 91.209.243.5, payload of hash of treatment
7. December 17, 2014 | 15: 40:23 | 713236 | IP = 91.209.243.5, IKE_DECODE RECEIPT Message (msgid = a3f0e3f9) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84Please repeat the debug with "debug crypto isakmp 100". And compare the config of the Phase 2 on both sides:
- Is what ACL crypto exactly in the opposite direction on both sides?
- Your transformation sets include exactly the same algorithms?
-
Satellite U840W - Toshiba Split Screen does not work
Hi all
My laptop is a Toshiba Satellite U840w. I reinstalled a new version of windows 8 pro but I lost all the software by default.
I decided to download Toshiba Split Screen to enjoy my 21:9 screen, but the problem is that it does not work!
When I run it, I can open his window to turn it but it does not appear in the notification area, and nothing happens.
I don't really know what to do, I hope someone has a solution. Thank you.
Kind regards.
Hello
I guess you have not installed all necessary drivers, tools and utilities that are available on the page of the Toshiba UE driver.
Make sure that you have installed the software suite next to the Split Toshiba screen utility
-Driver Toshiba system
-Toshiba system configuration utility
-Toshiba utility function of key
-Desktop Toshiba Assist -
I have a windows vista, before my vpn network worked perfectly, but when the update sp2 vpn does not work again so could any body can help me with this sound like Windows have no clue at all to this subject, so far I try most of the answers
but none works
Support FREE from Microsoft for SP2:
https://support.Microsoft.com/OAS/default.aspx?PRID=13014&Gprid=582034&St=1
Free unlimited installation and compatibility support is available for Windows Vista, but only for Service Pack 2 (SP2). This support for SP2 is valid until August 30, 2010.
Microsoft free support for Vista SP2 at the link above.
See you soon.
Mick Murphy - Microsoft partner
-
Help: Customer Cisco VPN &; Split Tunnel but not Internet
Hi Forum.
We are faced with this problem: after having successfully open a VPN connection with the Cisco VPN Client to a router Cisco, the rest of the world are not properly available more.
This is what has been verified / so far attempted to identify the problem on a Windows Vista computer:
-Router: Split Tunneling is allowed according to sysop
-On the VPN-Client: "allow Local Lan access" is checked
-On the Client (statistics): only STI VPN-rout configured listed unter "guarantee routes." "Local Lan routes" is empty.
-Calling 'http://www.google.com' in IE fails
-Call ' 74.125.232.116' (IE IP) IE works / ping the IP works.
-nslookup properly lists the current DNS server
-nslookup www.google.com resolves correctly the name of intellectual property
It seems that it is not that the connection with the rest of the Internet is deleted, but DNS resolution fails somehow, even though all signs point to the appropriate DNS server is in force and although the command line can resolve the name.
does anyone have a tip how to debug this correctly?
No worries Pat...
Sent by Cisco Support technique iPhone App
-Please evaluate solutions
-
Easy VPN between two ASA 9.5 - Split tunnel does not
Hi guys,.
We have set up a site to site vpn using easy configuration vpn between ver 9.5 race (1) two ASA. The tunnels are up and ping is reached between sites. I also configured split tunnel for internet traffic under the overall strategy of the ASA easy vpn server. But for some unknown reason all the customer same internet traffic is sent to the primary site. I have configured NAT to relieve on the side of server and client-side. Please advise if no limitation so that the installation program.
Thank you and best regards,
Arjun T P
I have the same question and open a support case.
It's a bug in the software 9.5.1. See the bug: CSCuw22886
-
I'm working on an installation of the laboratory program at home with my X-5506, and I got a split tunneling configuration problem. Every change I seem to give me internet access, gives me access to the local network or remove both. The current configuration, I took them both and I am a little puzzled. I have attached the configuration. Any guidance would be greatly appreciated!
Change:
split-tunnel-policy excludespecified
TO:split-tunnel-policy tunnelspecified
I notice you are using 192.168.0.0/24. Make sure that you do not work VPN'ing an address 192.168.0.0/24 as well (or a subnet that is also identical to your subnet that you are trying to access remotely) or it won't work. Overall, you should avoid using 10.0.0.0/24 and 192.168.0.0/24 in production networks because they are so frequently used in home networks. I also note that you have configured IKEv2. IKEv2 does not support split tunneling. SO be sure you use only the AnyConnect client in SSL mode. -
Your route to display the bookmarks bar does not work.
I carefully followed your directions and the bookmarks toolbar refuses to show. What Miss me? This utility shows no more, then what is it?
Right-click in the title bar, or in a place of the Bank on the Navigation toolbar does not display a menu with the menu bar or toolbar bookmarks, as well as other menu items?
-
iPad iOS9 Air split screen does not work
I have an iPad Air (model A1474) & I can't get the split screen function to work in iOS9.3.1. I turned off the iPad, reset all settings, update all applications and I don't always get the bar of the double line to split the screen. Tried with mail & message/safari.
It is not available on the Air iPad. From there.
http://www.Apple.com/iOS/whats-new/
- Picture in picture and drag more are available on iPad Pro, iPad Air or later and mini iPad 2 or a later version. Split view is available on iPad Pro, mini iPad iPad 2 Air and 4.
-
RTMPT / Tunneling does not work
I have Flash Media Streaming Server 3 running on a Windows 2003 with IIS 6 computer. I can see the samples of video on demand, locally and remotely very well using rtmp, but not rtmpt. I have disabled the socket pooling using httpcfg, but FMS 3 does not seem to be binding for all IP addresses on port 80. Next steps?
HBZYou can add ports in a comma-delimited list:
ADAPTER. HOSTPORT = xxx.xxx.xxx.12:1935, 80
Then restart the service of the FMS, and you should be all set. You can run netstat-nab from the command prompt to ensure that the FMS is bound to port 80
-
I have 2 Cat6, with IPsec SPA card, while the other did not.
I tried setting IPsec tunnel between them, but somehow can't bring up the tunnel, can someone help me to watch set it up?
A (with SPA):
crypto ISAKMP policy 1
BA aes 256
preshared authentication
Group 5
ISAKMP crypto cisco123 key address 0.0.0.0 0.0.0.0
ISAKMP crypto keepalive 10
Crypto ipsec transform-set esp - aes 256 esp-sha-hmac testT1
!
Crypto ipsec profile P1
Set transform-set testT1
!
Crypto call admission limit ike his 3000
!
Crypto call admission limit ike in-negotiation-sa 115
!
interface Tunnel962
Loopback962 IP unnumbered
tunnel GigabitEthernet2/37.962 source
tunnel destination 172.16.16.6
ipv4 ipsec tunnel mode
Profile of tunnel P1 ipsec protection
interface GigabitEthernet2/37.962
encapsulation dot1Q 962
IP 172.16.16.5 255.255.255.252
interface Loopback962
1.1.4.200 the IP 255.255.255.255
IP route 2.2.4.200 255.255.255.255 Tunnel962
B (wuthout SPA):
crypto ISAKMP policy 1
BA aes 256
preshared authentication
Group 5
ISAKMP crypto cisco123 key address 0.0.0.0 0.0.0.0
!
!
Crypto ipsec transform-set esp - aes 256 esp-sha-hmac T1
!
Crypto ipsec profile P1
game of transformation-T1
interface Tunnel200
Loopback200 IP unnumbered
tunnel GigabitEthernet2/1.1 source
tunnel destination 172.16.16.5
ipv4 ipsec tunnel mode
Profile of tunnel T1 ipsec protection
interface Loopback200
2.2.4.200 the IP 255.255.255.255
interface GigabitEthernet2/1.1
encapsulation dot1Q 962
IP 172.16.16.6 255.255.255.252
IP route 1.1.4.200 255.255.255.255 Tunnel200
I can ping from 172.16.16.6 to 172.16.16.5, but the tunnel just can not upwards. When I turned on "debugging ipsec cry ' and ' debug cry isa", nothing comes out, when I trun on 'cry of debugging sciences', I got:
"00:25:17: crypto_engine_select_crypto_engine: can't handle more."
Hello
You need a map of IPSEC SPA on chassis B do IPSEC encryption. Please see the below URL for more details.
Without a SPA-IPSEC - 2G or IPsec VPN Services Module of acceleration, the IPsec network security feature (configured with the crypto ipsec command) is supported in the software only for administrative for Catalyst 6500 series switches and routers for the Cisco 7600 Series connections.
Kind regards
Arul
* Rate pls if it helps *.
-
Œuvres ping for the VPN ASA5505 RDP does not work?
I have an ASA5505 VPN remote access facility
I have a server connected directly behind the ASA and I can ping the server without problem.
The reports being encrypted and decrypted packets VPN client
However when I try to RDP to the server packages encyrpted keep incrementing but the decrypted packets are not.
I also do not see all RDP traffic hit the server (checked by ethereal)
I did a packet trace and it succeeds, but ends with a parody of IP which I believe is correct as is the vpn traffic and not actually be encrypted.
This is the correction of the RDP session, I'm confused by one ICMP denied on line 2 that I am able to ping the server?
% ASA-6-302013: built of TCP connections incoming 88193 for external:172.16.24.4/50984 (172.16.24.4/50984) at internal:192.168.100.146/3389 (192.168.100.146/3389) (roger_ssl)
% ASA-4-313004: Denied ICMP type = 0, of laddr 172.16.24.4 on the external interface to 192.168.100.146: no matching session
% ASA-609001 7: built internal local-host: 192.168.100.37
% ASA-6-302015: built connection UDP incoming 88194 for external:172.16.24.4/50620 (172.16.24.4/50620) at internal:192.168.100.37/53 (192.168.100.37/53) (roger_ssl)
% ASA-4-313004: Denied ICMP type = 0, of laddr 172.16.24.4 on the external interface to 192.168.100.37: no matching session
% ASA-6-302015: built connection UDP incoming 88195 for external:172.16.24.4/64598 (172.16.24.4/64598) at internal:192.168.100.37/53 (192.168.100.37/53) (roger_ssl)
% ASA-4-313004: Denied ICMP type = 0, of laddr 172.16.24.4 on the external interface to 192.168.100.37: no matching session
% ASA-4-313004: Denied ICMP type = 0, of laddr 172.16.24.4 on the external interface to 192.168.100.37: no matching session
% 302014-6-ASA: disassembly of the TCP connection 88193 for external:172.16.24.4/50984 to internal:192.168.100.146/3389 duration 0: bytes of 00:00 0 flow closed by inspection (roger_ssl)
I have that configured NAT
NAT (internal, external) static source 192.168.100.0 192.168.100.0 static destination VPN_172 VPN_172
The only logical bit that is closed by the inspection flow? Is this to say that the server has not responded?
And decrypt packets increase not when trying to RDP
Does this mean anyting to anyone that I have arrived at the end of my knowledge of the SAA on this one!
Thank you
Roger
Answer is based on your other thread:
Maybe you are looking for
-
I've recently updated Firefox to version 42. On the old version, I could go tools-> Page Info and there would be a menu typical Edit at the top where you can select, copy, etc. On the new version this menu is absent and Ctrl C/Ctrl V do not work. Any
-
Toshiba 32TL838: flicker after fw upgraded in the menus, using HDMI input
Hello yesterday I updated firmware of my 32TL838 to version 6.4.0Y.1 / 94.6.27.8 using the upgrade feature network. After the upgrade, I reset the TV to start again with the factory settings. During the quick installation after the reset, I noticed a
-
Change the inventory on a T430i number.
I tried the following applications: Using the latest bios package: winflash32.exe - patch - dat ''. winflash32.exe - patch - dpc ''. These say they write in the BIOS and reboot the PC, but no settings are actually saved. With the help of the WinAIAPa
-
After changing the motherboard on my PC, a Dell Optiplex gx270s Windows XP SP3, the computer (which also works fine) does not see the CD/DVD or floppy drives CD, DVD or floppy is inserted. (He sees not thumb drives). When I look under the hardware in
-
Edit a music file so I can print the contents of the file list.
How can I print a list of the contents of the my music with wma file. file type?