Helps mapping of intelligent control B3 Vintage

Similar Questions

• How to set up intelligent control on a multimbral instrument

  Hello

  I'm with Kontakt multitimbral instrument inside Logic Pro X.

  I'm launching of the smart controls on all the midi channels to control certain parameters such as Attack, Release etc...

  The Smart Control pane only controls the instrument on channel 1.

  Any specific way to have intelligent controls on other instruments on other Midi channels?

  Best regards

  I had no problems with that.  You configure the Smart controls correctly?

  http://help.Apple.com/LogicPro/Mac/10.2.1/#/lgcp7e59f24b

• HP Pavilion 400-434 Office: intelligent control of hard disk: failure

  Hello

  It all started when the computer would go blank right after startup, the HP logo would come upward, then 'auto repair preparation", more... Just empty. After reading the forums online, I did all the possible troubleshooting steps and at the end I did the SMART test... the result was:

  Verification of the processor: past

  Intelligent control of hard disk: failure

  Failure ID: RGD7MK-7HV7RC-9XJ16K-60BB03

  After obtaining these results, when I turn on the computer, it gives me a blue screen saying: drive SMART 1 error (301) and told me to test once again, that I did and got the same result as above.

  Here is some info from the computer:

  Model: HP Pavilion slimline 400-434

  Processor type: pentium (R) of the Intel (R) J2900 @2. 41 GHz

  Thanks for your help!

  Hi there @Brugalgirl

  Welcome to the Forums of HP Support! It's a good place to find the help you need, other users, the HP experts and other members of the support staff. I understand that your computer does not start successfully, and you found a Smart Drive 301 error code. I'm happy to help you with this.

  I checked the ID of the failure, you've posted and verifies that the error. Unfortunately, this means that your hard drive needs to be replaced.  In view of the fact that the system does not boot, it is likely that the hard drive is completely unreadable, but depending on what you have on this subject, it may be worth your while to check with a local computer service shop and see if they can help to recover data from your hard drive.

  If your system is relatively new and may be covered by the warranty, or if you wish to fix with HP for the guarantee system, you can call in hotline to make these arrangements. In this case, please use the following http://www.hp.com/contacthp and create a folder for your question and contact HP. If you do not live in the United States / Canada, please click on the link below to get contact information for your region.
  http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  Otherwise you can look at a replacement hard drive yourself. If you have a set of recovery media, then you already have a factory image HP, which allows you to put in place a new hard drive with your original operating system. If is no longer, you have a set or did not have a set of recovery media, so you can see if there are not yet available for your model.

  HP computers - get HP recovery disks or HP USB recovery disc

  Let me know if you need help most. If it solves your problem, please mark this message as a solution.

• the intelligent control of hard disk detected an imminent failure.

  the intelligent control of hard disk detected an imminent failure. so no los data, please backup the content immediately and run the system diagnostics hard drive test.

  Hard drive 1 (301)

  in the diagnostic system

  All tests are failed...

  Starting the test

  Run in test

  TuneUp System

  I already run the hard drive test before that. but the problem stil occurs. What should I do?

  Yves wrote:
  How can I save the content?

  Hello

  Well, I can now use access HARD drive? In the affirmative, please try this:

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=us&prodNameId=3688870&prodTypeId=0&prodSeriesId=3688868&swLang=13&TaskID=135&swEnvOID=4055

  Otherwise, just replace the HARD drive and use the old HDD as a external HARD drive and you MAY BE able to recover data files from there.

  Good luck.

• intelligent control of hard disk detected an imminent failure

  Intelligent control of hard disk detected an imminent failure on disk 1. I have a Pavilion g7.1081nr laptop.

  Hello

  If you start getting SMART errors, this would indicate that hard is defective and must be replaced.  If you can still boot into Windows, I strongly suggest to do a backup of all your personal files, etc., as soon as you can.

  If your laptop is still under warranty, contact HP and arrange for the disk replaced - you can check the status of your warranty here.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  If you are out of warranty and would like a guide to replacing the hard drive yourself, let me know.

  Kind regards

  DP - K

• Xbox live help I need to control my back account

  really need help a family friend set up my email under his account and Noah my xbox live is ordered parental, not a problem with this otherwise that no longer us talk to him and live 1000 miles on bad terms, I want control of my account back.

  Hello

  For us to better help can you with your concern, you please give us the e-mail affected account?

  Also, can you please give us the exact error message that you receive by logging into your account?

  Thank you!

• Use outside technical help and allow them control of your computer

  I pay every month for technical assistance on my computer.  He is paid by credit card.  I've used them once and they solved my problem.  I'm having problems and would like to know if it is safe to allow these services take control of your computer as you look to help you diagnose and solve problems?  Thank you

  Hello

  Yes, in fact, some of these services are safe, but not all of them. In fact, most of them is not. You must make very extensive research before considering allowing anyone access to your computer and should be used only as a last resort.

  It will be useful.

• help map Grpahic for dell inspiron years 620

  question I have
  Reference Dell Inspiron years 620
  4 GB ram ddr3
  processor i3-2120
  hard drive 500 GB
  no graphics
  I searched for better graphics card for my desktop PC
  some told that my pc cannot support the graphics card to power
  tell me to buy the graphics card compact
  I need help
  What graphics card to buy NVIDIA or amd

  tell all the question and compatibility

  from this site
  Thanks in advance

  and also what company choose NVIDIA or amd.

  http://www.flipkart.com/computers/computer-components/graphic-cards/PR?SID=6BO%2Cg0i%2C6sn&otracker=ch_vn_computerco_filter_Categories

  Rishabh14

  Can I install this map
  This card is compatible.
  http://www.flipkart.com/Sapphire-AMD-ATI-HD-7750-1-GB-GDDR5-graphics-card/p/itmd7th7wdspnbrh?PID=GRCD7TGZBJSTR5YD

  The card will not fit.  Only low-profile video cards fit the slim towers.  One you want is this one HERE if you want to only the 7750 HD.  Otherwise, you can get the HD 6670 HERE.

• Works in the context-sensitive help mapping file

  I create a new project of Webhelp using Robohelp HTML 10, and I'm confused on the different pieces of information in a map file. I don't even know if my developer will give me a map file or if I create it, but I'd like to understand the concept of mapping better before I talk to him.

  I created a map using Robohelp file, and the dialog box "Edit ID card" Robohelp shows three columns: ID card, card #and topic. I automatically assign numbers map to my help topics. For example, a line indicates "Changing_Password" for ID card, '2' for card # and "Change Password" for the category. I know that the screen of the application of this topic is changepassword.cdl. The mapping file is supposed to tell the developer that this topic should be linked to changepassword.cdl and if so, where? Or can I give the developer this information separately? In addition, in the compiled file from WebHelp, this topic is named PasswordChanging.htm. Can I change the map ID to PasswordChanging instead of Changing_Password?

  Thanks for any help!

  It depends on how you want to work. Personally, I have my developers call help using the internal system page. They know that already. So I do not give anything for developers.

  In your case, the developer needs to know what id call to what page. How you communicate, it's up to you. As suggested by Jeff, you probably want to give the .h file of the contracting authority.

  @Jeff: the article describes the functioning of HR CSH. Van of developers who can create their own API. (This is what we did).

  Take a bow

  Willam

• Help map

  Hello

  I'm just scratrching the surface of 3D imaging and I seriously want the basics of low-floor cold.

  I started reading "3D in Photoshop", who has the basics of 3D and terminology set out in chapter one (very clever).  He talks about this card and that the card and this mapping and this mapping, assuming everyone knows what a map or mapping is.

  Well, in my case, I have not.  I need a definition very simple, basic in the following terms-

  MAP

  MAPPING

  Thanks for your help.

  Lee Evans

  Lakeview terrace, CA

  Said in other words, in Photoshop, it's about TEXTURE mapping. This is a 2D (map) image wrapped on an object 3D in a certain way (mapping), for example like this:

  

• Cannot provide an input parameter when starting a mapping of the control center

  Hello
  
  I have a problem with my control center. When I start a map that requires an input parameter, theres is no prompt to provide these parameters in the job details window.
  Last week, everything works fine. But now the jobs of law begins immediately. I can see the job details window but I can't provide an input parameter. What I have to change in preferences that I can insert an input parameter in the job details window.
  
  Thank you very much.
  
  Greetings

  Tools-> preferences-> prompt for the run settings.

  Concerning
  If

• With the help of Toshiba Remote Control PX1246E-1ETC on Linux

  Hi there, I'm trying to use this remote in combination with Ubuntu 8.10. I don't yet know what media center software that I like to use. But is it possible to get this working to control remotely using Ubuntu? Hope someone has a positive experience with it.

  John

  Hello

  AFAIK this remote control is designed for use with Win XP and MCE (media center edition).
  I think you will not be able to use under Linux, but this is just my personal opinion.

  See you soon

• HP Pavilion G6: INTELLIGENT control of hard drive failure

  Model: HP Pavilion Notebook PC g6

  PROD ID: LN220EA #ABV

  Warranty start date: 27/05/2011

  Smart Check: FAILURE

  FAILURE ID: 9C1G7F-5LK7KD-XD015G - 608L 03

  Hard drive 1

  Test drive: FAILURE

  What is my problem?

  Whenever you get an error message with 24 characters alphanumeric numbers indicating that the hard drive needs to be replaced to solve the problem
  
  Could be due to the Application or a driver conflict, virus issues, corruptions of files due to incompatible applications, improper stops, update failures due to conflicts, mounted sudden power sudden, so portable falls etc...
  
  HP will offer a replacement HDD if the laptop warranty is Active, otherwise you can buy a SATA hard drive in a nearby retail store
  
  Please make sure that you get at least equal as long as the original one in order to use recovery disks. If you need you can buy a bigger, but not smaller hard drive capacity. For example, if you have a 500 GB hard drive you can improve it to 750 GB hard drive, but not 320 GB hard drive
  
  Please try the troubleshooting below indicated once the steps:
  Step 01. Remove the battery and unplug the power adapter AC.
  Step 02. Press and hold the power button for more than 30 seconds
  Step 03. Plug the AC power adapter / (leave the battery for now)
  Step 04. Press the power button and check if the unit is operating normally
  
  If the steps listed above is not enough, then you can try reinstalling the hard disk on your laptop
  
  If the problem persists again please contact HP if your HP laptop is under warranty, HP could replace the hard drive and provide recovery media to restore the operating system to factory after the replacement (if you have not yet created recovery disks/USB support)
  
  Note: Back up all personal data on an external drive if possible. Otherwise, you can connect the HDD defective via SATA Adapter USB with another PC or a PC even after replacing the HARD drive & put in place of the operating system and try to copy / retrieve files.
  
  Please click on the link in order to identify, prevent, diagnose & recover against any failure to drive on HP Portable Hard Drives & Solid State Drives:
  http://h10032.www1.HP.com/CTG/manual/c02876562.PDF
  
  Please check your warranty for laptop to check the status and order a new hard drive
  
  Hope this helps, for other queries in response to the post and feel free to join us again
  
  * Click on the star of CONGRATULATIONS on the left to say thank you *.
  
  Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.
  
  Thank you
  K N R K
  Although I am an employee of HP, I speak for myself and not for HP

• Help! three digital controls by three Boolean values

  Hi guys, I really need your help. I am trying to create a program where I can choose the button (A - Z and 0-9) keys three keypad and use in order to increase the 3 individual respective Boolean values into the light. I work for a while now. Here's my program: manvery - happy:

  Tissue wrote:

  When I select 'a' of the digital list and I press the keyboard boolean unlit 'a', turns on him. When I press "a" again, the Boolean value lit will be unlight. While the program still works, I can always choose a different as key '5' and the other '5' key it will switch again when I pressed on it...

  Try something like the joint (LabVIEW 2011).

  By pressing one of the buttons (case insensitive) made alternate value Boolean coresponding. Change the selection will clear all indicators. Modify if needed.

• How the macro in the .h file is mapped to the control CVICALLBACK setting?

  I have created 8 control buttons and creates same reminder for all buttons. Have a multitude of 2 x 4 initialized with the value 1. When the user clicks a button value of 2 x 4 table must go to 0 (as the command button does not change the value 1 when selected). In order to complete the picture, I thought to use the CVICALLBACK control.

  The value corresponding to the ID of the control may change if you add or remove controls or if you change the tab order. Once I learned this, I stopped using it, so I can't be sure that these are the only conditions when this happens. In my opinion they are enough to avoid using the digital ID values at all.

  The 4 x 4 case derives from your code: you calculate 4 rows each of 4 elements. I tried to follow this approach in my switch statement, but you really have to adapt it to your situation and the structure of the IUR.