Hi, I changed my router today and now I can't print
any help appreciated
Hello
Thank you
First of all, you need to remove or reset the old setting on your printer by following the steps mentioned below.
Steps to reset:
On the front of the printer, go to network Menu > default network > Yes.
Once you have reset the network settings on the follow-up to the printer steps mentioned below to connect your printer to your wireless router
1. go in the control panel of the unit NETWORK > select the Wireless Menu > Select wireless configuration wizard
2. Select your network and enter the necessary information which will be asked to enter and you will get connected to your home network.
3. Once connected, you must add a new printer using the software on your computer.
* Say thank you by clicking on the "Bravo!" Star"located on the left *.
* Make it easier for others to find solutions, marking my answer to "Accept as Solution" if it solves your issue.*
Tags: HP Printers
Similar Questions
-
I have Apple TV gen 1. I changed my iTunes password and now I can't the Apple TV in the House. It will connect to iTunes. I type my Apple and a new password. My phone Gets a text with a verification code, but the Apple TVsaybadusername password or.
Your ATV1 has an old software system not updated for years. You have 2 factor (6 digits) or authorization of step 2 (4 digits) enabled for your Apple account. Here are the characteristics of the latter. I disable these on your Apple account and try again.
For Apple ID - Apple Support two-factor authentication
Frequently asked questions about the audit in two steps for Apple ID - Apple Support
-
I updated my iPad today and now I can't get cellular internet. Can anyone help please?
I updated my iPad today and now I can't get cellular internet. Can anyone help please?
It is a bug in 9.3 and persists in the 9.3.1
to get back to be
1. turn off the power, remove the sim card, reverse and insert sim card when asked. Or
2 disable cellular data, mode airplane and then turn off. Wait about 30 seconds and then turn it on turn off the airplane mode and then turn on the cellular data. He must find it.
but this is only a work around. If you turn off again, you will have the same problem and her you need to repeat the steps above.
Good luck
-
Satellite 1900-303: changed the BIOS settings, and now I can't boot from the CD drive
Can anyone help, I inadvertently changed the BIOS settings, and now I can't get the CD player to boot the pc back to the default settings, Windows xp seems to work ok as is the cd player.
If someone has the original settings, I would be grateful for any help.Derek has soon
Hello Derek
Use the F2 key to enter the BIOS settings and change the order of boot devices. This option is under the STARTUP tab. Otherwise, you can insert the recovery CD when the unit is turned OFF. Turn it on and immediately press the C button. keep it down for a few seconds and unit is forced from the CD/DVD drive.
-
Updated to Photoshop CC 2015.1.2 and now I can't print.
Updated to Photoshop CC 2015.1.2 and now I can't print.
Photoshop crashes when I select the printer controls.
With the help of Windows 7-64.
What should I do?
Hi CT_Vancouver,
Please make sure that your drivers are up-to-date.
You can see the Photoshop to solve printing problems
Kind regards
Assani
-
Java 7 is installed today and now I can't open any web page in FF!
I downloaded JAVA 7 today and now my mozilla open barely all the pages google and youtube in particular! I uninstalled Java restarted the PC and the problem still persists! I do not like using Chrome or any other browser for obvious reasons. Please can you help me?
are you an error?
Start Firefox in Safe Mode to fix the problem and to check if one of the extensions (Firefox/tools > Modules > Extensions) or if hardware acceleration is the cause of the problem (switch to the DEFAULT theme: Firefox/tools > Modules > appearance).
-
Removed from Garmin using MSconfig and now I can't print. The print spooler is not running
I wanted to speed up my computer and remove an item off my msconfig. Now I can't print. missing spooler. What should I do? I tried dating back to some time earlier, but all previous changes are missing
Operation could not be performed. The print spooler is not running
the question I wanted to delete was for Garmin
don101947
Hello
I don't know if you have already solved the problem of the other answer, but here's something you can try if your not confident using the command line.
Go to [start],-> [Control Panel]-> [administrative tools]-> [Services]
Depending on if your running XP, Vista or 7 you can have 2 tabs at the bottom of the window you see.
Select [Standard] if its not already selected. If you already have a large list, skip this step.
Scroll down and find the print spooler. Double click it, and then set the "Startup type" to [Auto]
then click [OK] and then make a right click again print spooler and select [start]
-
Changed router and now I can't print
BT have changed my router. I use a Mac 10.9. My printer is an officeject 4620. It worked fine before the change in router. I can print to the printer itself, I can print using the HP software (but it ask me to enter the IP address and then enter the router password) but cannot print from any software, that is to say the word. I don't get an error message and the computer seems to try and send it to the printer, but it does not. Someone at - it ideas?
Hi lynneseymour,
Welcome to the HP Forums!
I read your post about not being able to print wireless from the evolution of your router, and I'd be happy to help!
With regard to the new router you use, what's his name, and model number? How far is the router of the printer? There is a parameter called "Multicast" router, and it must be enabled for printing from a Mac.
To connect the printer to the new network, you will need to restore the default network settings on the front panel.
This can be done by following these steps:
(1.) by clicking on the key icon on the lower part of the front panel
2.) click the arrow on the button down to network and press Ok
3.) scroll down to wireless settings and then click Ok
Scroll 4) to the network by default and press Ok
5.) click Yes and the default network will be restored
Then, the printing system needs to empty the old print queue. To do this, follow this document about the reset printing system.
Do not click on the button to add another printer, the next step is to run the HP installation wizard to perform an automatic wireless connection.
The next step is to run the HP Setup Assistant to start an automatic wireless connection with a usb cable.
Follow the steps under "optional: I installed my printer... to move to a wireless network connection" to install the software of the printer for a wireless network connection.
I will be looking forward to meet you and thank you for visiting the HP Forums!
-
HP Laserjet P1102w: P1102w - change password and now I can't print wireless network
Recently, I changed the network password on our router Cisco Valet and without realizing it seemed to me making the wireless printing stop workinig.
I can always print to this printer via the USB cable, but it is not found on the wireless network.
I guess I have entered the time of info the first network I created this printer, but I don't remember how I did it.
Is there an easy way to reset the password that the printer uses, so we'll see on the wireless network?
Thanks in advance for any info on how to get this working again.
Replacement/change your wireless router try here. Same thing to change your password...
http://www.HP.com/global/au/en/wireless/reconfiguring-system-Help3.html
However, if you have a gateway device, all devices in gateway (modem + router) are terrible for connectivity and wireless performance. If this does not work, suggest you put this bridge in full bridge mode device and install your own router of high quality that YOU have full control over.
-
I got a new modem and the router and now I can't print wireless.
I have a Photosmart 8450 printer. My operating system is Windows7. I tried to follow the Scan doctor, but I guess I'm not tech savy enough to understand. It worked fine before the new modem and the router. She is 'offline' and I can't understand how to put line. Thanks for any help and easy enough for me to follow.
Hello raedene715.
Thanks for the transcript, it was useful.
Please, check the network cables and connections (side of the printer and router). If possible, try a different network cable.
See you soon!
-
When I try to print an e-mail sent to me, a picture of a telephone/fax machine and I can't print. He holds a lock in the upper right. I have Windows 7 and do not know how to disable this picture so that I can print on my Brother printer. Thanks to all of you who are a lot smarter than me.
There are no such displays no message or error Windows, so I would start by checking the website of manual or support for the printer, it is owner and see what he has to say on this screen.
-
I have istalled security code on my router and now I can't print.
I recently put a password on my router, thinking that my broadband was stolen. Printer dosent my work now, and the router does not recognize that it is on the system.
OK, you will need to re - install the printer. If you have Windows you can go to start > all programs > Hewlett-Packard > [your printer model] > add a device. Add a network printer or wireless when it asks. You may need to temporarily use a USB cable to connect the new network settings on your printer.
-
I changed the security permissions and now I can't access the file in IE
When I apply changes in the advanced settings, then click on apply this box opens: application security error
an error occurred applying security information to: C:\Users\Jeffry\AppData\Roaming\Microsoft...\D3DCompiler_47.dll
access is denied
continue cancel
Then another box is open behind her that says:Windows Security
Stop the spread of the permissions settings leads to an inconsistent state, in which some objects have the settings but others don't. If you have made the change by mistake, you must apply the correct change immediately in order to reach a consistent state.
OK The problem is that I do not remember what changes, I did, but I've tried every suggestion here, but none have worked so far. System Restore was not able to help so lets not suggest that.
I spent 30 million dollars on RegServe and although it helped clean up echoes it did not help this problem. Very complicated and frustrating!
Hi Jeff, allows to taste the simple options, let us know if you have tried these or not:
1 restore the permissions of folder for C:\Users\Jeffry: right-click on the file, go to properties, advanced security:
1.1 property confirm otherwise change it your account,
1.2 list to ensure that entries includes SYSTEM administrators group and your account, all have full control and none are inherited by the top.
1.3 the check "Replace all entries authorization child object with permissions entries inheritable from this object" box and click on apply.
2. try running SFC/scannow:
http://support.Microsoft.com/kb/929833
3. use FIX IT automatically search and solve problems: http://support2.microsoft.com/fixit/en-us?wa=wsignin1.0
4. create a new profile, logon, and testing, it works as expected, delete the old profile (backup your data first)
-
I am new to this group and need help with the above question. Help, please.
Thank you
KLG22
Thank you. I thought about it. The files on my external hard drive. As soon as I pulled the computer I managed to save.
Sent from my iPhone
-
I upgraded to the iPhone 5 and now I can't print on my HP OfficeJet 4500.
Hello
I was wondering why I lost the ability to print after upgrading to the iPhone 5. Worked very well with the iPhone 4 and iOS 5. I had to print via my wireless network so had my Mac on, but never had any problems. Now my phone says that it cannot find all printers.
Thank you
Diana
Thanks to everyone for the suggestions!
I tried another solution - put Printopia on my Mac. Works very well.
Maybe you are looking for
-
I've updated Firefox yesterday. Now, I can't load a calendar - bookmark, or the binding of applications. Here is what I get. I made this cookies are valid. The page is not redirecting properly Firefox has detected that the server redirects the reques
-
The slider side does not move when I put the mouse on it, I need to click below or on the arrow down. Once he left the first place, it moves. Also some applications like changing the city the weather button won't change.
-
upgrading Vista to Windows 7 Professional I followed the instructions given on the MS site to upgrade my vista to windows 7. I answered the questions and MS said that I had to purchase the Professional upgrade from windows 7. After purchasing, I tr
-
Cisco SX20 - cannot access web interface after factory reset
Hi guys,. I just did a factory reset on my SX20, and now I can't access the web interface, I need to add the key to release Basically I can't configure the IP addresses directly through the Executive Director of unity I need to add the release key a
-
I have Win7 Home Premium 32 bit installed on new computer OEM. I added more RAM (DDR3 1333 pair). Windows has asked to be reactivated, I did. Now WEI has no active button, shows no rating at all and says that the machine is not classified. He previou