Hive 1.4?

Similar Questions

• blue screen after Ko 2840149, error - "STOP: c0000218 {Registry hive failure} the registry cannot load the hive (file): \systemroot\system32\config\SOFTWARE.

  After I installed security KB2840149 on a 2008 VM w/exchange server that is running on the machine of Hyper-v server 2008 I'm dead in the water w / E-mail down hard.  The virtual computer is in a reboot cycle bluescreening before I can get anywhere.  Tried the last well known - no effect.  Safe mode - so bluescreens.

  BlueScreen info:
  STOP: c0000218 {Registry hive failure}
  The registry cannot load the hive (file):
  \systemroot\system32\config\SOFTWARE
  or its log or alternation.
  It is damaged, missing, or not accessible in writing
  I saw that it was a patch of replacement for a patch that crashed a lot of PCs.  Since there is no history on this patch, I wanted to check in a see what is the best way to fix this on a virtual machine?

  Being not so deep on VM, I wasn't sure if there was a better way. But I just put the virtual machine to load 2008 iso and then made the standard repair for registry problems off the coast of the article below.

  Of http:

  If the Windows registry is slightly or moderately damaged, you may be able to restart the computer in safe mode and use system restore to restore the registry from the computer to the last known good configuration. However, if the Windows registry is seriously damaged, all types of logon will be prevented. Trying to connect to Windows causes the system fails, then restart. In this case, you will need to boot the system into the recovery instead of Windows Console. Once in the Recovery Console, you can use the Startup Repair tool. Startup Repair tool automates common diagnostic and repair of the installations of Windows tasks starts longer.

  (a) start your Windows Vista or Windows Server 2008 DVD
  (b) on the first Setup screen click Next
  (c) in the lower left corner of the screen, choose "repair your computer".
  (d) on the System Recovery Options screen, select your Windows installation and then click Next
  (e) click on "Command prompt".
  (f) go to X:\sources\recovery > startrep.exe
  (g) this will take some time but will look at any registry related issues.

• corrupted: WINDOWS\ SYSTEM32\ CONFIG\ SOFTWARE Stop: c0000218 {Registry file failure} the registry cannot load the hive (file): SystemRoo

  corrupt: WINDOWS- SYSTEM32- CONFIG- SOFTWARE Stop: c0000218 { file registry failure} the registry cannot load the hive (file): any on windows server 2003.  How can I fix this

  Hello, getin99

  For help on Windows Server, you need to create a new post on the TechNet forums at the following address: http://social.technet.microsoft.com/Forums/en-US/winservergen/threads

• Registry cannot load the HIVE file; Need to fix WITHOUT the Recovery Console, computer will not play my Windows recovery disk.

  I need to fix my computer, I got the blue screen of death with the following error message. Registry cannot load the file \systemRoot\system32\config\SOFTWARE "HIVE".

  I read all the forums on how to solve this problem. I tried all the means which have been enumerated. None have worked so far because I can't get my CD player to load to run my Windows XP Pro disc to start the repair.

  Is there a way to fix this without the disc. I can't the computer after Windows XP display until he went blue. It's a computer original systemax, but I have since rebuilt it me with the new motherboard, hard disk, cdrom, dvdrom, ram, fans, cpu, etc... I just got a new monitor and hung up and blue screen of death appeared after that I turned the computer back on. I tried to fix this for 4 days now. Someone please HELP me.

  I got it fixed. THANK YOU SO MUCH for all your help!

• The registry cannot load the hive (file): \systemroot\system32\conig\software or its log or replacing. It is damaged, missing, or not accessible in writing.

  My laptop does not start all of a sudden upward - it crosses the safe mode screen, acts as if it is loading windows (display the windows screen) then becomes to empty, followed by a very quick flash of the message on a blue screen: "the registry cannot load the hive (file): \systemroot\system32\config\software or its log or replacing."  It is damaged, missing, or not accessible in writing. "Then, he repeats the cycle.

  I looked towards the top of the error on the Microsoft Knowledge base, and the hotfix request using the recovery disk, I.  I wonder how I can get the interactive help on laptop computer file so that I can run so that it fixes the problem... (http://support.microsoft.com/kb/307545).

  Advice, that someone could give me so that I can at least get started again windows go down all the important data before reinstalling Windows would be much appreciated.

  Thank you

  Chris

  Hey Chris,

  Thank you for visiting the Windows Xp forum

  I was wondering if you run a retail or OEM of Windows version. If you are using an OEM version of windows, you will need to use the recovery options you have from the manufacturer of your computer. If you run a commercial version, feel free to follow the article in the knowledge base you have found.

  http://support.Microsoft.com/kb/307545 how to recover a corrupted registry

  I was also wondering if you have another computer to work? If so and you feel comfortable or know someone who can remove the hard drive from the computer and connect it to another computer. You can view the disk hard kit to join. Once the hard drive is connected, you can go in my computer and copy all the files to another hard disk.

  Georgio
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Stop: 0xc0000218 {registry file failure} the registry cannot load the hive (file): \SystemRoot\System32\Config\Software is damaged, missing, or not accessible in writing.

  Original title: blue screen.

  My computer won't start even in safe mode... c000218 (failure of a registry file)

  Cannot load the hive (file): \systemroot\system32\config\SOFTWARE is damaged, missing, or not accessible in writing

  Hi rookiegeek,

  You did it of any material changes or software on the machine prior to this problem?

  The three possible causes of the problem are:

  (a) failure.

  corruption of file b) & defective hardware.

  (c) the problem can occur on shutdown.

  You can follow this link & check if the problem persists.

  Registry troubleshooting steps for advanced users

  Hope the helps of information. Please post back and we do know.

  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• ERROR OF THE HIVE: ACER ASPIRE 5515 LAPTOP: WINDOWS VISTA

  Hello

  I have a "Hive" error message that appears on a blue screen. Windows does not load. Any help getting this machine will would be appreciated.  Thank you.

  You can try erecovery at default settings when you save your data. In the Startup logo Acer press F2 to enter the bios and make sure that recovery disk to disk (D2D) option is selected in the main menu. Save and exit the bios. The machine starts, press the ALT key while pressing F10. This should present you with a menu for a fresh factory reset or a factory reset with your saved data.

  Jack E/NJ

• Difficulty for the file attribute "Update time" a file hive of the registry update on XP and Windows Server 2003

  "Time modified" attribute of a file file the registry hive is updated when you load and then unload the registry hive files without making any changes to the files on a computer that is running Windows Server 2008 or Windows Vista, or Windows 7

  I see a hotfix is provided for Windows Server 2008 or Windows Vista: http://support.microsoft.com/kb/973148/ and for Windows Server 2008 R2 or Windows 7: http://support.microsoft.com/kb/983544

  Question: I want to know if this problem is also present in Windows XP and Windows Server 2003, and if so, we have a solution already for XP and Windows 2003?

  Hello

  Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the public on the TechNet site. Please post your question in the below link: http://social.technet.microsoft.com/Forums/en/category/windowsserver/

• Windows xp does not start due to corrupted software hive.

  Windows xp won, t start.

  n, t go in safe mode,

  error message:

  failure of a registry file,

  Registry cannot load the hive (file)

  systemroot\systen32\config\software diary or his substitute is damaged, absent, or not writable

  http://www.pchell.com/support/recoverfromcorruptedregistry.shtml

  or Microsoft article...
  http://support.Microsoft.com/kb/307545

• Trying to access Windows XP on a Mac, receive stop error. failure of a file registry c000218 registry cannot load the hive (file)

  I have a Mac OSX, leopard, parallel 5 and Windows xp.   When I try to access Windows, either through boot camp or at the same time, I get the error message "stop. failure of a file registry c000218 registry cannot load the hive (file).  I bought Windows 7 but cannot get Windows Installer.

  The hard drive may be replaced . Or something is not compatible

• C0000218 {registry file failure} the regestry cannot load the hive (file)

  I have XP pro. on a Dell computer. Think that children may have picked up a few difficulties. When trying to boot into safe mode, I get "Stop: c0000218 {Registry file honor} the regestry cannot load the hive (file): \SystemRoot\System32\Config\Software or its log or replacing." It is damaged, missing, or not accessible in writing. »

  There is no disk that came with it, but I have anouther computer with the same windows. I tried to find a way to make a BOOT disk but cannot find a way. Is there a way to solve this problem with the windows disc?

  It's a pretty popular mistake these days and sometimes easy to get running, but you also want to figure out how it happened.  I always suspect Symantec/Norton products with this error, but we'll see.

  If you currently or have already had a whole isntalled Symantec/Norton products, what are the names and versions (if you know).

  Other variants are:

  STOP: c0000218 {Registry file failure}
  The registry cannot load the hive (file): \SystemRoot\System32\Config\SECURITY or its log or replacing. It is damaged, missing, or not accessible in writing.

  STOP: c0000218 {Registry file failure}
  The registry cannot load the hive (file): \SystemRoot\System32\Config\SOFTWARE or its log or replacing. It is damaged, missing, or not accessible in writing.

  STOP: c0000218 {Registry file failure}
  The registry cannot load the hive (file): \SystemRoot\System32\Config\SYSTEM or its log or replacing. It is damaged, missing, or not accessible in writing.

  I would start with a chkdsk/r since the recovery CD of Console you make (see below) and please answer a few questions...

  Maybe someday the dialog box 'ask a question' forums XP will ask these questions automatically when a new thread is started so I don't have to ask every time.  It might even be possible to solve a problem in a single response when enough information is provided.

  Please provide additional information on your system:

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..

  The question was preceded by a loss of power, aborted reboot or abnormal termination?  (this includes the plug pulling, buttons power, remove the battery, etc.)

  The afflicted system has a CD/DVD drive work?

  You have a true bootable XP installation CD (it is not the same as any recovery CD provided with your system)?

  Fill in the blank: my system was working fine until this happened: _.

  If the system works, what do you think might have changed since the last time it did not work properly?

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.

  This is not the same as recovery disks that may have come to a store to purchase the system.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

  http://www.ImgBurn.com/

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

  Do, or do not. There is no test.

  I decided to implement the points for a new puppy instead of a pony!

• Check the file system on C or registry cannont load the hive!

  Ok... I have a Dell Vostro 1510... all of a sudden, I can't on this laptop!  I have Windows XP Professional.  It lights up when I choose to start windows... I am said to be:

  Checking file system on c:

  The type of the file system is NTFS.

  Volume label is System.

  Then, when it starts to run it says: CHKDSK checks the files (step 1 of 3)... it happens to 47% finished and that's all!  It won't do anything else, it just stops!

  If I have to cancel the verification file system I get this message:

  STOP: c0000218 {Registry file failure}

  The registry cannot load the hive (file):

  \SystemRoot\System32\Config\System

  or its log or alternation.

  It is damaged, missing, or not accessible in writing.

  I do not have the disks provided with the laptop or I will say that I can not find them... I read a lot of these forums but none I saw helps me!  Because I can not enter and try to run anything!

  Thanks for any help in advance!

  I see you mentioned do not have all the disks with the laptop and maybe it's that he came not with any, because the installation files are likely in a hidden partition.

  but try to borrow a winxp cd and boot with it.

  then in the window settings pitch repair to start the recovery console.

  then at the prompt of disk, run the following >:

   

  Chkdsk /r

  Chkdsk /f

   

  then exit, remove the cd and restart the computer.

   

  the above commands are redundant, but nothing wrong with double controls.

   

  In addition, if you receive a following error on boot sector, then run via the recovery console fixmbr.

   

   

  
  --
  DB·´¯'·.. ¸ ><)))º> --> sent via windows live mail

  .

  DB·´¯'·.. ¸ >-))) º > ·´¯'·.. ¸ >-))) º > share nirvana mann

• SE error message: "the registry cannot load the hive (file) \systemroot\system32\config\software"when try to start on the original copy of Windows XP. "

  Original title: you're smarter then me. Help, please

  My windows xP home edition has crashed on my HP Pavilion a620n. Initially, I was able to get by using the original cd of the publishing house. Then it crashed again. Rebooted and pressed F8 and typed in my administrator id. This time, a cam of the screen saying that it was an ID of invaled. Re-checkeded my Id and it was OK. Put in my cd original and installed on a different partition. Problem is that I forgot to do a dual boot. Now I have two sessions of windows xp on the same partition. Am able to switch between them, but really need the original. When I click on the origianl happens with the registry cannot load the hive (file) \systemroot\system32\config\software.

  Is it possible to fix this?

  Thanks, it was a great help

• User profile hive cleanup service do not appear to work with Vista!

  HII,
  The user profile Hive Cleanup service do not seem to work with Vista. Does
  Anyone know equivalent that please. Thank you.

  You should post the question with all the details in the forum on TechNet here server:

  http://social.technet.Microsoft.com/forums/en/categories/ MS - MVP - Elephant Boy computers - don't panic!

• Error loading of the software hive

  Original title: the hive errror vista

  I dropped my laptop fro windows loading screen took a few minutes and then I got a message saying stop: c0000218 (registry file failure).  The file of registry cannot load the hive (file): \systemRoot\System32\config\SOFTWARE or its lof or replacing. It is damaged, missing, or not accessible in writing. How can I fix this if possible without a hardware replacement. UPDATE: I made an attempt to reinstall windows I get settings for windows loading and I get the loading screen of windows 7 and that a black screen with the cursor nothing happens at all so is this a hardware problem?

  Hello MTK1988,

  If we are still having problems with the Software hive, let's try the following:

  1. Start to repair the system and choose command line.
  2. Type the following commands:
  3. z:
  4. cd\windows\system32\config
  5. Ren software software.old
  6. ren system system.old
  7. Regback CD
  8. Copy the software z:\windows\system32\config
  9. copy the z:\windows\system32\config system
  10. Reboot and see if we are able to start Windows.

  Please note that if there is no directory regback, we should type the following:

  • Ren software software.old
  • ren system.old system.

  Let us know if that helps.

  Best regards

  Matthew_Ha

• Letter of changed but diving system hive has the correct registration?

  So my problem starts I think when I think that after updates, she needed a restart, but I just shut down my computer normally, completely forgetting the updates.

  At the start, everything seemed normal but I couldn't connect, I was stuck on an endless loop of 'welcome' (the just kept spiral cursur spinning) and then after the reapir on startup mode via pressing f8 I realized my windows partition drive letter was changed, so after looking around a bit on this forum I found this :

  http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/2180b9e6-c2ff-4421-bb06-fcb99e7e2021

  When a similar problem that occurred with the drive being exchanged letters, so I followed the instructions to fix it through the registry via the command prompt to the repair mode, import the system hive to system32/config/and then change the 'system' hive drive letters around for good, but my real hive file system (system32/config/system) seems to have drive letters the right way around , and the system hive is preloaded when you open the register has them completely reverse (also introduced completely new letters that I have not yet used/assigned before).

  So my problem is windows without going through the system hive in the config and loading other it elsewhere (the Beehive system preloaded when you open the registry)? or I'm doing something wrong: S

  Thanks in advance for your help guys :)

  Don't worry, I've managed to fix.

  I just crossed yet the comand prompt in vista recovery and used diskpart.exe is an internal drive management utility used by windows and then changed the letters of volume there and made sure in the register of letters, where also successfully changed and then ran a diskcheck using attributes of/f/r so ' chkdsk/f/r' and it fixed.

  I'm now going to back up my computer and it defrag jjust wrap: P

  Thanks for your help though!