Hot swap Despperation

Similar Questions

• HP xw8600: Hot Swap disk xw8600

  BIOS is updated.  1.42 (?) Win 7-64

  I bought an opportunity StarTech SATADOCK525 Trayless 5.25 "Bay mounted 2.5" and 3.5 "SATA Drive Dock on eBay. I installed it in a workstation HP xw8600 without a RAID but my BIOS saids that the hard drives are controlled by the RAID BIOS. I can't the hot swap to work. The drive receives power and works of HD if the disc is in the dock when I start the computer. However I that I swap the disk, the new HD no longer works. Is it because of the BIOS RAID control.

  I have 3 HD over the CD/DVD and the Dock, so I need 5 active SATA cables. I have RAID + AHCI value because I need 5 active ports.
  
  Is this normal? Or do I have a problem?  The motherboard - BIOS supports hot swap?

  Looks like port SAS-0 strives to get hot.  Now try with a HD with real data.

• Adding a new Hot Swap HDD to a PowerEdge T420

  My server T420 currently switchable 3-hot hard drives installed and I intend to install 2 hard drives hot swap. The server has ESXi 5.1 and I am looking for the instructions for this process. The plan is to turn off the server, install the new HDD and reconfigure the BIOS to power for hard drives new. Is the installation process for the similar server to our plan or very different?

  Shad515,

  You can stop the server, but it is not necessary since you have hot swappable hard drives. While in THE RAID controller BIOS, simply insert drives into available slots. Hard drives will appear in a 'READY' State At this point, you have to reconfigure your virtual disk as needed.

• PowerVault MD1000 Perc 6/E hot swap

  Which would prevent me from doing a Hot Swap on a 136GB 15K SAS drive on a PowerVault MD1000 with a Controller PERC 6/E for Adaptive Read Ahead, write new policy, broadband strategy of disk, RAID-10 in degraded state, a defective disk cache 64 KB, disabled?

  Blew up a car and you want to make sure I can hot swap on this machine. I read through product docs, but you are looking for something extra that I want to check that I missed on. Server of our warranty and support from last year. Everything I see is green lighted to go, but I always want to get will as many resources as possible before blowing a RAID 10 potentially because a controller had some setting that prevents a switchable good hot to rebuild. Make backups before swap, swap during off-peak hours doing rebuild starts on commercial operations.

  I read through docs:

  http://public.support.Unisys.com/pcproducts/ESX/docs/DellDocs5.4/en/Perc6i_6e/chapterb.htm

  http://support.Dell.com/support/eDOCS/systems/MD1000/en/Hom/om_en.PDF

  http://support.Dell.com/support/eDOCS/systems/MD1000/en/supmatrx/Feb08update/md1000_SupportMatrix.PDF

  Hello matt.newman,

  For the MD1000, you can replace a failed during execution of the MD1000 drive.  When you insert the replacement drive, it will start a reconstruction.

  To replace the Perc6 you will need to do is the following:

  1. Make sure you have a good backup tested all the MD data
  2. Turn off the server and the MD
  3. The PERC6. Remove and replace
  4. Turn on the MD & wait that he move to a ready state
  5. Turn the server & go in the new Bios Perc6 / configuration
  6. You have to re-create the raid10 & together for Adaptive Read Ahead, political writing back, broadband 64 KB, off the disk cache strategy
  7. Once you have created the raid then leave the PERC6 configuration utility and the Server post to the operating system
  8. Once logged on the operating system you can then run the restore to restore your data to the MD

  Please let us know if you have any other questions.

• 9800 Simulator Reload/Hot Swap with Eclipse 1.1 does not work for me

  Hello

  I've updated all plugins Eclipse today range below;

  BlackBerry Java plug-in 1.1.2.201004161203 - 16 net.rim.EclipseJDE.feature.group
  BlackBerry Java SDK 6.0.0.29 net.rim.ejde.feature.componentpack6.0.0.feature.group
  BlackBerry Java SDK 5.0.0.25 net.rim.ejde.feature.componentpack5.0.0.feature.group
  BlackBerry Java SDK 4.7.0.57 net.rim.ejde.feature.componentpack4.7.0.feature.group
  BlackBerry Java SDK 4.6.1.49 net.rim.ejde.feature.componentpack4.6.1.feature.group
  BlackBerry Java SDK 4.6.0.23 net.rim.ejde.feature.componentpack4.6.0.feature.group
  BlackBerry Java SDK 4.5.0.28 net.rim.ejde.feature.componentpack4.5.0.feature.group

  I try to get hot to labour in the 9800 unsuccessfully Simulator code swap. All the online documentation says it should work and I saw the evidence that it works on the old JDK to http://supportforums.blackberry.com/t5/Testing-and-Deployment/How-To-Use-Hot-Swap-with-the-BlackBerr... . Nice article... but it does not mention the eclipse plugin. I can't find "Simulator of reuse" check box on one of the eclipse debugging configuration forms!

  When I change my code and trying to debug a second time, I get the message "A BlackBerry debugging session is already active."

  I can run the Simulator 9800 ok, but it takes 10-15 minutes of startup: ^(et cela tue ma productivité.)

  Could someone rim give a clear statement or point me to a final resource stating if hotswap is supported on the eclipse plugin.

  Thank you

  Randy

  I got it work after trying two additional things. I don't know which one solved the problem.

  1. I had an entry in my environment variable path pointing to a directory of 'bin' of the eclipse plugin that I deleted old.

  2. I did a complete new installation of the classic eclipse 3.5.2 1.1.2 BlackBerry plugin eclipse and plugin SDK 6.0.

  Don't know which of these things is switchable hot work.

  I still get traded an exception when the debugger attaches more switchable hot but if I click here my code gets hot and I am able to continue debugging on the 6.0 9800 Simulator so I'm a happy guy

• Drives hot swap in BIOS not safe to remove the value

  I have a Doc Icy as the docks of the internal disks in a Bay with two power switches front of 5.25 inch front - one for the 2.5 inches dock bay and one for the Bay dock of 3.5 inches.  In the last inserted here readers as well as internal hard drives would come in safe to delete list.  Apparently a Win 7 update fixed the internal drives appear.  Now, even if for the ICY Doc SATA ports are on hot swap in the BIOS, they still do not appear in the delete list safe, which means that the superior policies drive removable section don't appear in the tab Device Manager strategies as they did and still do for USB drives.

  I found here in the forum a few lines of registry added to disable records showing in safe to delete the list, so I wonder if there are a few lines or a tweak for these lines to get two ICY DOC SATA ports to appear in Safe to remove - or y at - it another way?

  Here's the instructions to Remove readers of safe to remove from the other post by Bobby Mikkelson.

  1. click on Start

  2. in the search programs and files box, type the command

  3. under programs, click command prompt , click run as administrator

  If you are prompted for an administrator password or a confirmation, type the password or click on continue.

  4. copy and paste or type each of the commands at the command prompt and press enter after each command

  Reg.exe add "HKLM\SYSTEM\CurrentControlSet\Services\msahci\Controller0\Channel0" / f/v TreatAsInternalPort /t REG_DWORD /d 0x00000001

  Reg.exe add "HKLM\SYSTEM\CurrentControlSet\Services\msahci\Controller0\Channel1" / f/v TreatAsInternalPort /t REG_DWORD /d 0x00000001

  5 restart your computer to activate the registry changes

  Note: There may be some trial and error to determine the appropriate ports (also called "channels").

  The number of channel indicated in the device maybe Manager may not match the channel number in the registry, you may need to set the value and check the desired effect.

  There is currently no entries like this in HKLM\SYSTEM\CurrentControlSet\Services\msahci\

  In case it is not clear - I WANT that drives DOC ICY appears in safe to remove.

  Win 7 Pro 64-bit

  ASUS Z87.-A.

  All drivers and updates to the operating system to date.

  Hello

  Your question is better suited for TechNet where experts on this platform will help you better, please post your request in the Sub forum:

  https://social.technet.Microsoft.com/forums/en-us/home

  Hope this information helps, for assistance please answer.

• Hot swap does not

  Hello community

  I looked around, without success, and it took a lot, too much time to settle. Keep in mind, I'm no expert with the java/eclipse development environment, so what might seem routine for you would not be for me.

  I had a project that depends on another, I make a change to the Basic project and it used to reflect properly. Now, however, I have to reboot before the changes to the basis of work. I tried the upgrade, copying the empty spaces of work/projects projects, nothing doesn't seem to work and no info on why it fails. Hot swap has just stopped working. Remember that if I make a change to the main project, hot swap works. All ideas

  Eclipse 3.7.2

  BB plugin in 2.0

  JDK 6 and 7

  Thank you

  And it has not worked in another Simulator.

  Back to 1.3, now it works

  It's bad, maybe someone could understand the source? Or have I missed something obvious? It cost us a lot of valuable time...

  Bravo

• Hot-swap drive case

  I did a small update to help me with my computer backup, etc.

  When I was building my computer Baz Studio North advance I think this hot-swap drive thingie:

  SUPERMICRO CSE-M35T-1B black hot-Swapable 5 Bay SATA HDD Enclosure

  http://www.Newegg.com/product/product.aspx?item=N82E16817121405 & cm_re=Supermicro-_-17-121-405-_-produit

  I have a BONE and disc 4-1 TB drive in my raid.

  Is this microphone Hot swappable always a good choice, or are there others.

  I will be buying 2 extra 1 TB drives for backup and yet, for now keep my raid as four 1 TB drives.

  Thank you

  Rowby

  Yes Rowby

  That's the one.

  Baz

• Reference Dell 6248: hot swapping and upgrade battery links

  I have a set of switches Dell 6248.  I have a few questions to explore:

  (1) can I add/remove the CX4 cables while the switch is working?  (I guess it's the same rules as a cable normal Ethernet...)

  (2) can I add/remove modules while the switch is working?

  First scenario I'm looking at: extend the stack on a stacked rack.

  I think the process here is, install a switch of spare with stacking module, run off battery cables to the battery, breaking and re-Assembly of the ring, then turn on the switch, confirm the ID stack and connectivity and migrate customers to it.  I can totally hot cables plug the CS4, right?

  Next scenario I'm curious: upgrade of 12G to 48G stack.

  Can I exchange the accumulated 12 GB card and swap the 48G card in when the switch is on, or do I have to turn it off?  Connectors on the 48G card the same?  (CX4..)  Can I / layout 48G and 12G cards in a pile during my upgrade?  Is the maximum length of cable the same (3 m) on a stack of 48G?

  Thank you!

  -danny

  Hey Danny,

  The stackable modules are not hot-swappable. The cables are, but for the modules to detect that it must present when the switch is started. A reboot is also required for stacking on these ports using Ethernet. Yes 48 GB stackable modules also have a 3 meter cable.

• Hot Swap Raid 1 with 2 members of cold to the distribution

  I use a pair of w/Raid 1 PE T610 as a backup destination. The couple have three members. One of the members to be toggled Alternatively every day to the data in any news. When the safe drive is released and reconnected in the hot bay must rebuild with the rotation disc right? Give me a member of spinning and yesterdays pair in the trunk? Old Member States should also rebuild automatically right?  Comments please...

  The problems are varied, unpredictable and random, BECAUSE it is used in one different manner that it was. Potential problems:

  Corruption of data. That is the first reason for not to do. The table is sensitive to the loss of data due to errors in read/write unprotected during the reconstruction. This frequently more increases the chances of data loss. If you are mobile 2 TB of data and Exchange on a daily basis, averages say you will experience a loss of data, every 6 weeks. A 'real' backup solution has the ability of error checking and check inconsistencies in the data. If a single drive in an array of gradient is the only source of data, there may be no verification or correction - it is simply lost.

  Unresolved foreign configurations. At some point, your disk will appear as 'foreigner '. In a perfect world, all you need to do is to delete it and assign it as a spare drive to rebuild. The server assigns its configuration at startup to determine which configurations are foreign to it. If the controller "forgets" to its configuration and must decide which drive is the 'good', he can choose the wrong, or he might try to mesh together (data loss). Sometimes, these foreign and local configurations are lost and cannot be resolved.

• T440s not detected on hot swap external battery

  Initially I thought it was just a problem of linux.

  Its the same thing on windows 8.

  Remove and then reinsert the external battery and windows some extended shows two stacks when you right-click in the system tray.

  The battery is detected again when I:

  Insert the power cable,

  suspend and resume

  put into hibernation and resume

  Restart

  I'm on BIOS 2.17

  Does anyone else have this problem?

  Michael

  For me it turned out be a hardware problem.

  Catches of battery marked '1' on the back do not seem to go far enough to trigger the events of the APCI indicating the battery inserts.

  I found if I removed the plug completely manually and pulled him so the battery would be detected.

• Swap hot PA-MC-8TE1 +.

  Hallo,

  Can I make "hot swap" with a PA-MC-8TE1 + interface on a router 7200?

  Hello

  Not sure in your country. In my country, we use E1. Yes, you can configure E1 channeled as the previous interface E1/PRI 1200 hm PA

  Kind regards

  Maher

• Swapping hot rulebases to 10.3 with ODS

  Hello

  10.3 OPA running on IIS and we call Oracle Server of determinations with .net and PeopleSoft Integration Broker.

  We just made a rule change in OPA, can we just overwrite the file .zip existing on the server of the OPA, or do we need to put the server down and vice versa, etc.. ?

  Most of the hot swap documentation I found had to do with Interviews of determinations Web and mentioned the following three lines in application.properties:

  Load.rulebase.As.Resource = false

  RuleBase. Path = / WEB-INF/classes/rulebases

  cache. Loaded.rulebases = false

  
  

  I have the cache.loaded.rulebases = false line, but do not see others in the application.properties file.  I should add, or is it not a problem?

  Update: we tried, and it worked fine.  It is an advantage for us because it means that we can make changes to rule OPA on the fly without bring down the whole system.

  Good to know!

• Reuse a RAID disk and hot spare procedure

  My questions are for a PE R720xd with the PERC RAID internal H710P controller.

  I have replaced several RAID drives in the past, but I never did this before, so I was hoping to confirm my procedure for hard drives hot swap. A drive failed on one of my live servers. In the past I would always bring back the server during a maintenance window and replace the drive by using the configuration utility to make sure everything went correctly. This particular server has become a system of very high availability, so I was hoping to use for hot spare option do without bring down the server.

  The other issue is that Dell is not in stock on the disk, I need so I intend to use a same car I replaced recently on a server off-production that has already been fixed in a RAID1 in another Dell R720 Server table. Any time, I have never replaced a RAID drive, I always used a new drive out-of-the-box, so I'm also not 100% on how to prepare the drive to use for a new RAID array.

  I thought I am brings the donor server down and come off the drive I want to enjoy this the RAID array server using the configuration utility. So a question is - is there anything else I need to do preparation used in car for use in the new table?

  With respect to hot-swapping which lead to the new array, is it really as simple as just popping one out and put a new in? Can I do to confirm it has taken - apart from just confirming that the lights blink like crazy during synchronization?

  Thanks for your understanding!

  C.Short,

  You can switch the drive, but it will be not just to rebuild there is data on the hard drive. So when this disc is inserted, it will show foreign. You will need to do is to boot to the controller (Ctrl + R) and then CLEAR the foreign Configuration. Once completed, then you will be able to rebuild the disk on the virtual disk, you can do the BIOS of the controller, or from the OpenManage web interface (depending on the operating system).

  Let me know if it helps.

• Switchable T430 hot [CF]

  Buonasera,

  e possibile avere prezzo e disponibilita per cassetti n ° 2 hot swap s - ata by T430

  Buongiorno, the sto contattando by mail.