HP xw8600: Hot Swap disk xw8600

Similar Questions

• Adding a new Hot Swap HDD to a PowerEdge T420

  My server T420 currently switchable 3-hot hard drives installed and I intend to install 2 hard drives hot swap. The server has ESXi 5.1 and I am looking for the instructions for this process. The plan is to turn off the server, install the new HDD and reconfigure the BIOS to power for hard drives new. Is the installation process for the similar server to our plan or very different?

  Shad515,

  You can stop the server, but it is not necessary since you have hot swappable hard drives. While in THE RAID controller BIOS, simply insert drives into available slots. Hard drives will appear in a 'READY' State At this point, you have to reconfigure your virtual disk as needed.

• PowerVault MD1000 Perc 6/E hot swap

  Which would prevent me from doing a Hot Swap on a 136GB 15K SAS drive on a PowerVault MD1000 with a Controller PERC 6/E for Adaptive Read Ahead, write new policy, broadband strategy of disk, RAID-10 in degraded state, a defective disk cache 64 KB, disabled?

  Blew up a car and you want to make sure I can hot swap on this machine. I read through product docs, but you are looking for something extra that I want to check that I missed on. Server of our warranty and support from last year. Everything I see is green lighted to go, but I always want to get will as many resources as possible before blowing a RAID 10 potentially because a controller had some setting that prevents a switchable good hot to rebuild. Make backups before swap, swap during off-peak hours doing rebuild starts on commercial operations.

  I read through docs:

  http://public.support.Unisys.com/pcproducts/ESX/docs/DellDocs5.4/en/Perc6i_6e/chapterb.htm

  http://support.Dell.com/support/eDOCS/systems/MD1000/en/Hom/om_en.PDF

  http://support.Dell.com/support/eDOCS/systems/MD1000/en/supmatrx/Feb08update/md1000_SupportMatrix.PDF

  Hello matt.newman,

  For the MD1000, you can replace a failed during execution of the MD1000 drive.  When you insert the replacement drive, it will start a reconstruction.

  To replace the Perc6 you will need to do is the following:

  1. Make sure you have a good backup tested all the MD data
  2. Turn off the server and the MD
  3. The PERC6. Remove and replace
  4. Turn on the MD & wait that he move to a ready state
  5. Turn the server & go in the new Bios Perc6 / configuration
  6. You have to re-create the raid10 & together for Adaptive Read Ahead, political writing back, broadband 64 KB, off the disk cache strategy
  7. Once you have created the raid then leave the PERC6 configuration utility and the Server post to the operating system
  8. Once logged on the operating system you can then run the restore to restore your data to the MD

  Please let us know if you have any other questions.

• Drives hot swap in BIOS not safe to remove the value

  I have a Doc Icy as the docks of the internal disks in a Bay with two power switches front of 5.25 inch front - one for the 2.5 inches dock bay and one for the Bay dock of 3.5 inches.  In the last inserted here readers as well as internal hard drives would come in safe to delete list.  Apparently a Win 7 update fixed the internal drives appear.  Now, even if for the ICY Doc SATA ports are on hot swap in the BIOS, they still do not appear in the delete list safe, which means that the superior policies drive removable section don't appear in the tab Device Manager strategies as they did and still do for USB drives.

  I found here in the forum a few lines of registry added to disable records showing in safe to delete the list, so I wonder if there are a few lines or a tweak for these lines to get two ICY DOC SATA ports to appear in Safe to remove - or y at - it another way?

  Here's the instructions to Remove readers of safe to remove from the other post by Bobby Mikkelson.

  1. click on Start

  2. in the search programs and files box, type the command

  3. under programs, click command prompt , click run as administrator

  If you are prompted for an administrator password or a confirmation, type the password or click on continue.

  4. copy and paste or type each of the commands at the command prompt and press enter after each command

  Reg.exe add "HKLM\SYSTEM\CurrentControlSet\Services\msahci\Controller0\Channel0" / f/v TreatAsInternalPort /t REG_DWORD /d 0x00000001

  Reg.exe add "HKLM\SYSTEM\CurrentControlSet\Services\msahci\Controller0\Channel1" / f/v TreatAsInternalPort /t REG_DWORD /d 0x00000001

  5 restart your computer to activate the registry changes

  Note: There may be some trial and error to determine the appropriate ports (also called "channels").

  The number of channel indicated in the device maybe Manager may not match the channel number in the registry, you may need to set the value and check the desired effect.

  There is currently no entries like this in HKLM\SYSTEM\CurrentControlSet\Services\msahci\

  In case it is not clear - I WANT that drives DOC ICY appears in safe to remove.

  Win 7 Pro 64-bit

  ASUS Z87.-A.

  All drivers and updates to the operating system to date.

  Hello

  Your question is better suited for TechNet where experts on this platform will help you better, please post your request in the Sub forum:

  https://social.technet.Microsoft.com/forums/en-us/home

  Hope this information helps, for assistance please answer.

• swap disk failing on R510

  Sorry for the basic question, but I'm happy to be considered a fool if I can

  do things.  :)

  Error on LED is "E1810 HD 5 fault"

  This disk is part of a RAID-1.  Machine is running CentOS 5.  OMSA is not installed.

  R510, 8 car chassis.

  What is the recommended route to replace the defective drive?

  (1) hot swap by pressing the button delete drive, install the new drive, cross your fingers, automatic

  rebuild?

  2) starts at Dell Support Live, run OMSA who go and do the replacement of this way

  3) go into the BIOS and make the replacement here.

  (1) is easiest if it works, of course, but it's an important machine, so the safest way

  is the best.

  Thank you very much for your time.

  See you soon

  None of them are "safe".

  1) there are many reasons that may prevent disk rebuild automatically, if it does not rebuild automatically, without OMSA, so you'll need one of the other methods to clear foreign config or assigned as a hot spare to start reconstruction.

  Just make sure that you insert the ' hot' drive (not being able to replace).

• 9800 Simulator Reload/Hot Swap with Eclipse 1.1 does not work for me

  Hello

  I've updated all plugins Eclipse today range below;

  BlackBerry Java plug-in 1.1.2.201004161203 - 16 net.rim.EclipseJDE.feature.group
  BlackBerry Java SDK 6.0.0.29 net.rim.ejde.feature.componentpack6.0.0.feature.group
  BlackBerry Java SDK 5.0.0.25 net.rim.ejde.feature.componentpack5.0.0.feature.group
  BlackBerry Java SDK 4.7.0.57 net.rim.ejde.feature.componentpack4.7.0.feature.group
  BlackBerry Java SDK 4.6.1.49 net.rim.ejde.feature.componentpack4.6.1.feature.group
  BlackBerry Java SDK 4.6.0.23 net.rim.ejde.feature.componentpack4.6.0.feature.group
  BlackBerry Java SDK 4.5.0.28 net.rim.ejde.feature.componentpack4.5.0.feature.group

  I try to get hot to labour in the 9800 unsuccessfully Simulator code swap. All the online documentation says it should work and I saw the evidence that it works on the old JDK to http://supportforums.blackberry.com/t5/Testing-and-Deployment/How-To-Use-Hot-Swap-with-the-BlackBerr... . Nice article... but it does not mention the eclipse plugin. I can't find "Simulator of reuse" check box on one of the eclipse debugging configuration forms!

  When I change my code and trying to debug a second time, I get the message "A BlackBerry debugging session is already active."

  I can run the Simulator 9800 ok, but it takes 10-15 minutes of startup: ^(et cela tue ma productivité.)

  Could someone rim give a clear statement or point me to a final resource stating if hotswap is supported on the eclipse plugin.

  Thank you

  Randy

  I got it work after trying two additional things. I don't know which one solved the problem.

  1. I had an entry in my environment variable path pointing to a directory of 'bin' of the eclipse plugin that I deleted old.

  2. I did a complete new installation of the classic eclipse 3.5.2 1.1.2 BlackBerry plugin eclipse and plugin SDK 6.0.

  Don't know which of these things is switchable hot work.

  I still get traded an exception when the debugger attaches more switchable hot but if I click here my code gets hot and I am able to continue debugging on the 6.0 9800 Simulator so I'm a happy guy

• Hot swap does not

  Hello community

  I looked around, without success, and it took a lot, too much time to settle. Keep in mind, I'm no expert with the java/eclipse development environment, so what might seem routine for you would not be for me.

  I had a project that depends on another, I make a change to the Basic project and it used to reflect properly. Now, however, I have to reboot before the changes to the basis of work. I tried the upgrade, copying the empty spaces of work/projects projects, nothing doesn't seem to work and no info on why it fails. Hot swap has just stopped working. Remember that if I make a change to the main project, hot swap works. All ideas

  Eclipse 3.7.2

  BB plugin in 2.0

  JDK 6 and 7

  Thank you

  And it has not worked in another Simulator.

  Back to 1.3, now it works

  It's bad, maybe someone could understand the source? Or have I missed something obvious? It cost us a lot of valuable time...

  Bravo

• Hot swap Despperation

  Hello

  I changed my computer a while now.

  and when I install everything on this computer whenever I try to hot swap any application

  using Eclipse with java Blackberry plugin for eclipse, it does nothing.

  I have to close and reopen the emulator. I tried EVERYTHING but to no avail.

  IM desperate here, can someone give me a hand please?

  I use Windows 7 Home Premium, I tried a workoround for the issue of authorizations for with no luck.
  He has worked with an older version of the plugin Eclipse '1.3.0', but it's a pain for re - configure everything.
  for some reason any the last version of the plugin won't let me not hot swap.

• Hot-swap drive case

  I did a small update to help me with my computer backup, etc.

  When I was building my computer Baz Studio North advance I think this hot-swap drive thingie:

  SUPERMICRO CSE-M35T-1B black hot-Swapable 5 Bay SATA HDD Enclosure

  http://www.Newegg.com/product/product.aspx?item=N82E16817121405 & cm_re=Supermicro-_-17-121-405-_-produit

  I have a BONE and disc 4-1 TB drive in my raid.

  Is this microphone Hot swappable always a good choice, or are there others.

  I will be buying 2 extra 1 TB drives for backup and yet, for now keep my raid as four 1 TB drives.

  Thank you

  Rowby

  Yes Rowby

  That's the one.

  Baz

• Impossible to fill out the case of the composer from vm - hot add disk failure

  I'm checking a pool of composer, but the extraction fails with the error to the user saying "no server available for this transfer.

  and the connection to the server has the following sequence of warnings in the application log

  EventID 104: No server available transfer to transfer VMS/datacenter/PathtoVM/PoolDesktopVM not name Session: SessionIDString

  EventID 104: Session: SessionIDString reason no. ready transfer servers have access to storage for the VM me: vm-xxxx disk key: 1234

  EventID 104: Session: hot SessionIDString add to the user disk failure: username desktopDn:CN = name of the PoolDesktopVM

  The snapshot that depends on the pool has been published on the forwarding server and comes to 2.9 GB. He could not be connected, but the extraction of the VM based on that snap fails 3.0 GB on the 3.7 GB the customer view says he has to download

  The virtual machine with the snapshot is windows XPSP3 on hardware v7 with vmdk stocked thickness 1.

  The composer generated obtained vm controller buslogic scsi parallel and 3 thin provisioned vmdk added to chain SCSI 1 to account for the persistent drive of the composer and the disposable disc over the virtual machine swap file.

  The composer added 3 discs would explain the remaining space, that the customer has left to check.

  The forwarding server is hardwarev7 using the parallel scsi controller free such as recommended in the view 4.6 installation guide

  Can someone help get beyond the hot disk failure add that seems to be triggered when (I guess as the forwarding server) tried to mount?

  Hello

  It is a requirement. Transfer server THAT VM needs to access the desktop under transfer disks. in other words, host th transfer server running vm must be able to access disks of office under body.

  -noble

• Reference Dell 6248: hot swapping and upgrade battery links

  I have a set of switches Dell 6248.  I have a few questions to explore:

  (1) can I add/remove the CX4 cables while the switch is working?  (I guess it's the same rules as a cable normal Ethernet...)

  (2) can I add/remove modules while the switch is working?

  First scenario I'm looking at: extend the stack on a stacked rack.

  I think the process here is, install a switch of spare with stacking module, run off battery cables to the battery, breaking and re-Assembly of the ring, then turn on the switch, confirm the ID stack and connectivity and migrate customers to it.  I can totally hot cables plug the CS4, right?

  Next scenario I'm curious: upgrade of 12G to 48G stack.

  Can I exchange the accumulated 12 GB card and swap the 48G card in when the switch is on, or do I have to turn it off?  Connectors on the 48G card the same?  (CX4..)  Can I / layout 48G and 12G cards in a pile during my upgrade?  Is the maximum length of cable the same (3 m) on a stack of 48G?

  Thank you!

  -danny

  Hey Danny,

  The stackable modules are not hot-swappable. The cables are, but for the modules to detect that it must present when the switch is started. A reboot is also required for stacking on these ports using Ethernet. Yes 48 GB stackable modules also have a 3 meter cable.

• Hot Swap Raid 1 with 2 members of cold to the distribution

  I use a pair of w/Raid 1 PE T610 as a backup destination. The couple have three members. One of the members to be toggled Alternatively every day to the data in any news. When the safe drive is released and reconnected in the hot bay must rebuild with the rotation disc right? Give me a member of spinning and yesterdays pair in the trunk? Old Member States should also rebuild automatically right?  Comments please...

  The problems are varied, unpredictable and random, BECAUSE it is used in one different manner that it was. Potential problems:

  Corruption of data. That is the first reason for not to do. The table is sensitive to the loss of data due to errors in read/write unprotected during the reconstruction. This frequently more increases the chances of data loss. If you are mobile 2 TB of data and Exchange on a daily basis, averages say you will experience a loss of data, every 6 weeks. A 'real' backup solution has the ability of error checking and check inconsistencies in the data. If a single drive in an array of gradient is the only source of data, there may be no verification or correction - it is simply lost.

  Unresolved foreign configurations. At some point, your disk will appear as 'foreigner '. In a perfect world, all you need to do is to delete it and assign it as a spare drive to rebuild. The server assigns its configuration at startup to determine which configurations are foreign to it. If the controller "forgets" to its configuration and must decide which drive is the 'good', he can choose the wrong, or he might try to mesh together (data loss). Sometimes, these foreign and local configurations are lost and cannot be resolved.

• Hiding HP ENVY 15 t-j000 Quad Edition w/SSD and hybrid propulsion system. Swap disk for one SSD Question.

  Hi all!

  I bought the HP ENVY 15 t-j000 Quad Edition and opted for the WSSD 24Go cache as well as the hybrid drive 1 TB. Do I have a problem just buy a kit of cloning and spend the hybrid propulsion system to a full on SSD in the future if I choose to?

  I did some research but I can't isolate an answer if yes or no I might encounter problems on account of the Intel RST be "associated" with the traditional HARD drive caching.

  So I wonder if I can't just simply disable acceleration of RST, clone HARD drive for an SSD via a cloning kit, remove the HARD and the SSD drive and call it a day?

  Any help with this is appreciated!

  Purgingomen wrote:

  Thanks for the info but I was even more so, I was wondering if I would have a problem Exchange with a new SSD hybrid drive later by cloning.

  I thought that I would stick with the 8 GB of RAM and WSSD combo of cache/HDD for now and sometimes down the line (as in a year or two) to get rid of the HARD drive for a full on SSD, disable caching and at the same time move to 16 GB of RAM.

  But I don't know if yes or no the WSSD cache/HDD combo makes it difficult to clone and swap the HARD drive and then just leave the disc of "cache" of 24 gigas (which is more a cache drive) there to be upgraded later.

  -Rob

  Well, I think a pure 2.5 "SSD should work on the system but make sure the cache is removed. For the purposes of cloning, I suggest using the DD command:

  http://en.Wikipedia.org/wiki/DD _ (Unix)

• T440s not detected on hot swap external battery

  Initially I thought it was just a problem of linux.

  Its the same thing on windows 8.

  Remove and then reinsert the external battery and windows some extended shows two stacks when you right-click in the system tray.

  The battery is detected again when I:

  Insert the power cable,

  suspend and resume

  put into hibernation and resume

  Restart

  I'm on BIOS 2.17

  Does anyone else have this problem?

  Michael

  For me it turned out be a hardware problem.

  Catches of battery marked '1' on the back do not seem to go far enough to trigger the events of the APCI indicating the battery inserts.

  I found if I removed the plug completely manually and pulled him so the battery would be detected.

• Can the two versions of Windows 7 installed once on two disks be used for the hot with the same PC swap

  I want to use the same key to install Windows 7 on two different HARD drives and use them one at a time on the same PC.

  I have a hot spare disk Bay. I want to be able to exchange the HARD disk for troubleshooting Windows etc. Should I buy another key?

  I just realized that some information I have given is incorrect.

  I have not installed a new copy of Windows 7 on the second disc. I actually reconfigured it with an image of the first hard drive.

  In this case can I leave Windows on the second disk, and exchange them warm without any problem?

  I've heard people cloning the C drive and there change places if anything ever goes wrong.

  Would not be Windows treats the second disc I've reconfigured as a cloned disk?

  Keylonta:

  You are right. If you clone a drive with a good installation running, the system knows no difference between readers. It works simply. It is not request a new activation if Exchange you them.

  Similarly, if you use something like Acronis to make an image (complete backup of the drive) and then burn that image on a new disk, the system accepts the new drive as the former and, once again, do not request a reactivation.