How to configure das MD3200i load balancing
I would like to connect a MD3200i (with two raid controllers) to one of our Windows 2003 R2 servers without the aid of a switch.
After most of the documentation, some things remain pretty obscure to me. I'm new to MPIO/balancing and cannot figure how to set up.
Is it possible to connect 1 nic host to RAID 0 and another host nic to RAID 1 and then combine the bandwidth? Thus having 2Gbs instead of 1Gbs? Or is it only a redundant path sollution, happening the other controller in case of failure of the first line. How can I configure this regarding the IP addresses, subnets. And where is the configuered to load balancing. This is explained in the documentation? I can't find it. I found a few examples that include the use of a switch, but none with das sollutions.
What I have is 4 the MD3200i UTP cables to connect to the host. 2 the high raid controller and 2 on the lower raid controller. And use that I have 4x1Gbs, resulting a connection 4Gbs to a single partition on the MD3200i of load balancing.
Thanks for any help.
Multiple paths and in windows 2003 load balancing is managed by the driver MPIO is installed when you install the 'host' or 'full' version install MD Storage Manager. There is no need to separately aggregated network adapters to get the aggregate bandwidth. The pilot, by default, uses repetition alternated on all ports connected to a single controller.
Also, for a single virtual disk, all i/o through a single controller and the second controller acts as a redundant path. So, if you have 2 x 1 Gbps connections to each controller, you will have, at most, 2 Gbps for each partition. Now, each controller can have virtual disks, so the second controller may have a second partition that will also have a separate between 2 x 1 Gbps connection.
You can set IP addresses and subnets that are similar to the way that you would with a switch as long as you can test the connection port. It would be wise for each NETWORK card on the host on a different subnet and each port on the MD3200i on the corresponding subnet. This will make it easier when you set up your iSCSI.
You can use the configuration utility to MD in place your iSCSI sessions too
-Mohan
Tags: Dell Products
Similar Questions
-
How to check the webnode load balancing?
Hi I know where my corrections are load-balanced in all nodes in my web.
For example, I have 3 nodes of web (web1.example.com, web2.example.com, web3.example.com)
How will I know if my new connections are routed to all nodes in the web.
AND how do I know the number of connections from different nodes.
Thank you
PrasadHi I know where my corrections are load-balanced in all nodes in my web.
For example, I have 3 nodes of web (web1.example.com, web2.example.com, web3.example.com)
How will I know if my new connections are routed to all nodes in the web.
AND how do I know the number of connections from different nodes.
Check Apache log files on each of the nodes (error_log * and access_log *) and you will find the entries you want.
You can also get more details the software load balancing.
Thank you
Hussein -
We are currently using the "configuration.properties" file to identify load balancing our servers, but we are curious to see if it is the recommended method to configure load balancing, or if there is a better way.
I opened a case with Oracle support and asked the same questions - entry configuration.properties of the file servers is the only supported method used by Peoplesoft to balancing upward through 8.54.
See also: how the Installer Application Server Load balancing and failover (Doc ID 1252846.1)
-
Problem in Configuration of Hyperion FDM load balance...
Hi all
I installed hyperion essbase, planning, Hfm and Fdqm 11.1.1.3 version.
but I get error when setting up the configuration of fdm load balance...
error: when I click on test connection in authentication providers (Shared services (CSS))... get the error message like cannot create ActiveX component
Please give me answer if you know about it.
Kind regards
MadyThis error indicates that the dcom COMJNIBRIDGE object is not able to successfully launch or it was not properly registered on the FDM application server:
(a) start > run > DCOMCNFG
(b) expand Component Services > computers > my computer > DCOM CONFIG
(c) locate the COMJNIBRIDGE object, right-click and choose "Properties".
(d) click the identity tab and choose "This user" and look for the Service of FDM account and enter and confirm the password
(e) re - test -
Hello
I have some difficulty of implementation, network load balancing in VMware - I'm not sure what mode of load balancing that I use.
I have an ESXi 5.5 - host connected to a HP Procurve switch I have configured for 2 VLANS (40,41).
On the switch, I created 2 trunks (Trk10, Trk20) I scored on two VLANs:
trunk Trk10 trunk 23,47
24,48 trunk Trk20 trunk
VLAN 40
name of "trial".
untagged 1-22
Tagged 50, Trk10, Trk20
no ip address
output
VLAN 41
name "PLC".
tagless 25-46
Tagged Trk10, Trk20
no ip address
output
Port 23 and 47 will ESXi-host1 and port 24.48 will ESXi-host2.
40 of VLAN is to have the network 192.168.40.0/24.
41 of VLAN is to have the network 192.168.41.0/24.
I created a virtual switch that has 2 NICs in it, but how do I set the load balancing mode?
The virtual machine is slow on the internet right now, and I suspect the packets going to the VLAN evil.
(Time of balancing mode is set to 'Route based on the original virtual port code').
Kind regards
Soren
Let me know if you need more information.
Could you do a 'show interface memory' and 'show interface' on the HP switch and paste it here?
I would remove the trunks as I don't see why this is necessary in your configuration...
Make sure the road based on virtual port ID what origin is selected on vSwitch1 and both exchanges configured (PLC and trial).
Remove the trunks on the HP switch and tag/UNTAG required VLANS on individual ports that were previously used in these trunks...
Quick config necessary for HP...
conf t
without trunk 23,47 Trk10 trunk
without trunk Trk10 trunk 24.48
VLAN 1
23,24,47,48 not marked
VLAN 40
Tagged 23,24,47,48
VLAN 41
Tagged 23,24,47,48
WARNING: You may have a few hickups network when you do...
What model switch you use...?
/ Rubeck
-
5.1.2 is edge load balancing service logon aware?
Hello
We expect configure edge gateway Load Balancing Service using vCloud Director 5.1.2 and vCloud network and security 5.1.2
Is it implemented no consciousness of the session of load balancing? I found a tip in this blog: http://blogs.vmware.com/vcloud/2012/11/how-to-configure-a-load-balancer-using-vcloud-networking-and-security-edge-device-vshield.html, but its not mentioned in the vCloud Director Administrator's Guide (5.1.1)
If this is possible in 5.1.2 where can I get more information on that?
What kind of awareness of the session is possible (cookie, setting html)?
Best regards
jmarschall
Hello
Yes, taking consciousness/session persistence is supported on the edge. As stated on the blog post you referenced, cookie based (HTTP) and SSL (HTTPS) ID session, as Source IP based session persistence is taken in charge. Use of cookies, you can still define if you want to use Insert cookie or cookie prefixing.
-
Hello
I have DC with 192.168.10.2 255.255.255.0 P.DNS 192.168.10.2 & ADC 192.168.10.3 P.DNS 192.168.10.2 255.255.255.0
When I configure the network load balancing in win2012r2 std I get below error. Please help on this.
"NLB Manager running on a system with all networks bound to NLB mifht does not work as expected.
If all interfaces are ser to run NLB in "unicast" mode, Manager NLB will fail to connect to the hosts. »Thank you.
This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)* -
ASA Vpn load balancing and failover
Hi all.
We have two asa5520 configured as main unit and emergency in failover configuration, and everything works fine.
Is it possible with this configuration (switch), configure the vpn load balancing/grouping?
Thank you
Daniele
Hi Daniele,
You cannot run two of them on two firewalls ASA, VPN feature load balancing or failover functionality.
Where you need to use the two feature, you must use more than three ASA firewall, two first ASAs will work as the failover and the ASA third will work as cluster VPN for them, the following example uses four firewalls:
ASA1 (active FO) - ASA2 (TF Standby)
(VPN virtual master)
|
|
|
|
(Backup VPN device)
ASA3 (active FO) - ASA4 (TF Standby)
Kind regards
Wajih
-
vShield Edge 5.1.2 load balancing HTTPS health check possible?
Hello
We expect configure edge gateway Load Balancing Service using vCloud Director 5.1.2 and vCloud network and security 5.1.2
Is it possible to configure health checking with HTTPS and configure the URI to use for the control?
Best regards
jmarschall
Hello
You have 3 options to check on the edge of health:
1 TCP: checking the simple TCP connection
2 HTTP: sends HTTP GET using either the default value {/}, which is accessible by default on almost any server, but may be changed to any other URI.
3 HTTPS: sends hello SSLv3 client messages and check the server Hello coming from the virtual machine. No URI is included.
If you CAN do health checks for HTTPS, but NOT for any custom URI. Instead, it checks for valid SSL beyond the normal TCP communications.
-
Api ViSDk fails when behind a network load balancer
Hello world
I have an application that uses the VI SDK to find the Virtual Infrastructure of periphery. This application is originally a network configuration of the load balancer.
Having this kind of configuration ntwork affects the SDK API, of VI. The funny problem are all the virtual machine but there is a problem with getting the host systems.
Can we do anything to make it work without changing the configuration of the network?
Any help related to this is appreciated
Thank you
Tejas
Yes. See: http://pubs.vmware.com/vi-sdk/visdk250/ReferenceGuide/vim.SessionManager.html#sessionIsActive
Steve JIN, VMware engineering
Creator of VMware Infrastructure Java API: http://vijava.sf.net/
VI Java API 2.0 - 15 times faster than the AXIS of loading, 4 + faster in deserialization; only 1/4 of the size required by AXIS. More importantly the freedom to redistribute your applications.
-
How to configure OAM 11.1.2 the script load balancing?
Hello
I am currently setting up Oracle Access Manager to work with load balancing
In fact, I did the configuration with my browser, and I'm looking to do the same thing with a script.
Where is the configuration stored? Domain configuration file? DB store?
Is there a command WLST to do this config?
Concerning
An excerpt from wlst that will do the trick:
domainRuntime()
name = ObjectName ("oracle.oam", "type", "Config");
writeSig = ["java.lang.String", "javax.management.openmbean.CompositeData"]
oamHostKey = "DeployedComponent/Server/NGAMServer/profile/OAMServerProfile/OAMSERVER/serverhost.
oamPortKey = DeployedComponent/Server/NGAMServer/profile/OAMServerProfile/OAMSERVER/serverport"."
oamProtKey = "DeployedComponent/Server/NGAMServer/profile/OAMServerProfile/OAMSERVER/serverprotocol.
MBS. Invoke (name, 'applyStringProperty', [oamHostKey, StringSettings(oamHostKey,"__myhostname__").toCompositeData (StringSettings.toCompositeType ())], writeSig)
MBS. Invoke (name, 'applyStringProperty', [oamPortKey, StringSettings(oamPortKey,"__443__").toCompositeData (StringSettings.toCompositeType ())], writeSig)
MBS. Invoke (name, 'applyStringProperty', [oamProtKey, StringSettings(oamProtKey,"__https__").toCompositeData (StringSettings.toCompositeType ())], writeSig)
its dynamic and you need to worry about increasing the version number or concurrent access, etc...
-
VPN3000 Load Balancing - synchronization of the Configuration
I have found information on the configuration of hubs for load-balancing and realized that. I can't find any information on how the Member devices keep their configurations in sync. Is it automatic or is it necessary to update all members manually when changes are made?
Dennis,
Automatic synchronization of the configuration on the hubs is not possible. You must manually synchronize the configs.
See you soon
Gilbert
Rate this post if it helps
-
Dear.
I use ebs 12.1.3 and db 11.2.0.3 OS OUL5x64
in one applTier, I could see the ip address of the clients when they connect to the system in the access_log but
with the average level has 2 servers AP1/AP2 configure with a LoadBalancer in front.
verifying the connection in the Apache log file (access_log.1410393600) we see that the balancer IP address of load.
Please let know us if he died to set up so that I can see in file access_log which client (Ip address) connected to Server (AP1 or AP2)
Thanks in advance.
Concerning
Please see (how to show the Client IP address in The Access Log when using A load balancer (Doc ID 1355549.1)).
Thank you
Hussein
-
Hyperion 11.1.2.3 Linux load balancing installation - how to test?
Hi all
I installed the version Hyperion 11.1.2.3 on 2 Server (6) of Linux. We installed the Foundation Hyperion Planning and Essbase on Server1. Hyperion Planning on Server2 (Load balance).
Installation and configuration performed and workspace, planning of work in both servers. In the Weblogic planning Cluster is created by EMP Configurator only and deployed Planning0, planning of the depenses1 servers.
Now how to test the load balancing happens or not?
Thank you
Mady
As demand would go through web server (OHS), first thing to try would be to stop planning0 and check if you are able to do things, then vice - versa. By default, I think that the load balancing would be responsive, so as the first request goes to planning0 then the depenses1 planning and planning0.
Thank you
Vivek
-
vCO 5.5 high availability / load balancer configuration
I do a planning for a new deployment of vCO 5.5 and I would like to take advantage of the new features for high availability, but documentation seems to be a little lacking in Department of load balancer. I hope someone knows the answers to the following questions using zero in on possible configurations for load balancing options:
Calls to instances of vCO they state or can I use a setting of type stateless round robin for the configuration of lb or what do I need to support sessions?
Is there a health control end point which I can query the load balancer to automatically remove service instances in a configuration active / active failure? If there isn't a specific is a good audit can be done to create a service to act as a health check?
Did he already works with a configuration similar and willing to share their experiences?
Hello
You can read the following article which explains how to configure Nginx as the load balancer. I hope it's useful.
VMware KB: Nginx Configuration load lalancing software VMware vCenter Orchestrator 5.5
Kind regards
Radostin
Maybe you are looking for
-
My speed has decreased between the router and the modem is not working properly, what can I do to increase the download speed with my Time Capsule 802.11n
-
Photos app begins when the iPhone plugged into iMac?
Whenever I connect my iPhone to my iMac the Photos app starts. Is there some setting somewhere to prevent this? Thank you -Mike P.S. I use the latest operating systems on all my devices (El Capitan and iOS). I looked in the settings in the Photos on
-
Tecra 9100 does not supply power to the top
Hello I got Tecra 9100 laptop computer and you have a POWER PROBLEM.Basically, it got stuck at the start of the OS and I was unable to click or move the mouse to do something. So I held the power button to turn it off. I do not turn on again entered
-
Satellite U305 - left CTRL key is stuck
Somehow, in a hurry one day, I published a few unusual combination of keys such as Fn-break, Ctrl-Ins or something like and now the left WHAT CTRL is stuck to restart the computer. I can't Ctrl + C or CTRL-V with the left CTRL key. I can at least use
-
Conversion of Vista/XP on R61 problem
Hi all! It's my first time here and I really hope that someone will be able to solve my problem because I'm already desperate. Recently, I bought the Thinkpad R61, model NF5DEPB with Windows Vista professional. I met problems with connecting to netwo