How to create a bootable DVD/USB since the recovery Partition?

Similar Questions

• Q: How do I restore from USB if the recovery partition is deleted?

  Hi, make a backup of my spectrum 14 of jealousy cumputer Windows 7 on a USB stick with hp Recovery Manager. After that I deleted the restore disk partition and installed Windows 8. Now have sleep/power issues on Windows 8, need to go back to 7 can I test before sending it in for repair.

  Even if I did a backup USB, of bus I can't boot from the USB and the ect/f11 option at startup, does nothing, yet windows just starts.

  Now, how can I restore from a USB Pendrive without having access to the F11 restore the disk option, how to reinstall System Restore?

  Hello

  A backup is not a clone. You have cloned partition to a USB bootable for her to work.

  The HP Backup & Recovery Manager does not copy the recovery partition, even if you back up the entire hard drive.

  Here is a reference for the HP Recovery Manager manual.

  Unless you do a recovery as a DVD or USB media, the only source for what is available to you is to buy a set of recovery disks.

  I would like to have better news for you on this subject.

  Best regards.

• Windows vista Home premium recovery question - how to get the source for windows vista home edition premium as the recovery does not work since the recovery partition

  How to get the source to windows vista Home premium recovery is not from the recovery partition and gives me an error message

  Hello

  Contact the computer manufacturer and ask them to send you to vista recovery disks to reinstall the operating system back as it was when you bought it

  they do it for a nominal cost of $

  or borrow a vista microsoft dvd; not a HP, Acer recovery disk etc

  Make sure that you borrow the correct 32-bit or 64-bit microsoft dvd to your computer

  they contain all versions of vista

  This is the product key that determines which version of vista is installed

  http://www.theeldergeek.com/Vista/vista_clean_installation.html

  How to replace Microsoft software or hardware, order service packs and replace product manuals

  http://support.Microsoft.com/kb/326246

• Satellite Pro A200: How to create Dual boot; Vista & XP using the recovery CD

  I just bought a laptop Satellite Pro A200, which was supplied with the product for Vista and XP Recovery discs.
  The license specifically Vista also XP licenses.
  Can I set up a dual boot so that I can boot to Vista or XP? If so, how?

  I would also like a third boot, Red Hat Linux 9.
  Any comments?

  Hmmm. Usually it s possible to use two or more operating systems on the computer, but as far as I know the Toshiba Vista recovery CD formats whole disk when installing Vista and this will lead to the loss of the OS installed.
  I m not 100% sure on the recovery of the newest XP CD called RECON doesn t CD include an expert mode which allows to choose between the different partitions.

  So I guess that each use the recovery CD will format the HARD drive and erase the installed data. But of course, you can try to install the two BONES and to check if the restore XP CD allows to choose the second part of the installation of the OS.

  If it does not, it seems that you will need to an original XP from Microsoft CD or the original CD of Vista to use the two BONES.

  Best regards

• Qosmio - How can I create a bootable DVD of OS?

  Hello
  -----
  Please help me

  I have a laptop Toshiba Qosmio with Microsoft Windows Vista Ultimate.

  The DVD of the operating system was attached with the laptop, but now I've lost him.
  But I have the files that was in the original DVD
  But I don't know how to make a bootable DVD to reinstall the operating system

  IT'S FILES

  [http://9ore.net/view/3619/TTTTT.png]

  HELP PLZ

  You didn't post what Qosmio laptop you have, but you can create the recovery disk using the Toshiba Recovery Disk Creator.

  This tool creates the recovery disk that you can you to reinstall the OS.

  Maybe you should look in the user manual. You should also find information about how to create a recovery disk.

• Portege R100 - how to create a bootable SD card?

  Hello

  I'm trying to update my BIOS of v1.40 to v1.60. I don't have an external floppy drive, or a CD-Rom. I downloaded both versions of the bios upgrade. The version of windows does not install, coming up with an error of not being able to run in V86 mode.

  I read in some places to a SD card bootable using the Boot SD and a 2,88 MB image. Where can I find this picture? And how to add the update to the BIOS for it? Or what is the problem with the BIOS update, I downloaded?
  Thanks in advance for any help you may be able to give me.

  Post edited by: Bertee

  Hello

  You can create a bootable SD card using the SD start utility which is preinstalled on some Toshiba units. But as far as I know with this card, you can start only to the DOS mode and there is no image on the SD card! Moreover, I don t think you can upgrade the BIOS with an SD card. To update the BIOS, you need a compatible floppy drive.

  What are supported readers for this device:
  http://support.toshiba-tro.de/KB0/TSB5100S70004R01.htm

  You will find a description how to update the BIOS:
  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/FAQ.jsp?service=EU&FID=TRO0000000b07

  Good bye

• HP pavilion 15 laptop: how to create the recovery partition?

  By mistake, my little brother have formatted the recovery partition. I'm not able to refresh the PC through update & recovery option in the settings of your laptop... I have the unique language of HP Pavilion 15 notebook.windows 8.1. Please guide recreate me the partition...

  Hello

  Thanks for posting in the HP Support forum. Welcome!

  I'm afraid that you can't create partitions of recovery if they are deleted. End users cannot do.

  If the computer is originally shipped with Windows preinstalled by HP (OEM of Windows for example), you can buy HP recovery media. They are generally cheap. You can use it to restore your computer to factory default condition. Here's how:

  > > http://support.hp.com/us-en/document/bph07143

  > > http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html

  And once you receive the recovery [DVD or USB pen drive] media, here's how to use it to restore default factory/Windows to a condition:

  > > http://support.hp.com/us-en/document/c03489643

  > > https://www.youtube.com/watch?v=PC3sUc3lr3E

  If the computer is originally not is not come with Windows pre-installed, but you install on your own after that, then you need to use the Windows installation media to reinstall Windows. You can get Windows installation ISOs from the Microsoft web site and then burn it to a DVD > > https://www.microsoft.com/en-us/software-download/windows8

  > > http://www.howtogeek.com/80094/how-to-burn-an-iso-image-in-windows-7/

  Please, let me know if this helps and works for you. Feel free to post for follow-up questions.

• Create the recovery Partition D on DVD - HP Pavilion 6620f

  I just replaced the original, slowly due to lack of 1 TB of internal hard drive that came with this PC with a Western Digital, which is 300 GB. When you restore the backup of the original image, there was not enough space to restore the recovery Partition D. PC operating system is Windows 7 Home Premium SP1.

  Someone told me to put the score on a DVD "bootable" in case of future need. 2 questions:

  1. What is the solution?
  2. If so, can someone tell me how to do? Or direct me to a place to learn?

  I'm NOT a technical person found thing in replacement of entire disk completely intimidating despite all the learning that I had! That's why I don't know what to do now - or if it's feasible even for a "non-techie".

  Any suggestions most appreciated! Thank you.

  Linda

  lindairene,

  Your correct. The DVD will be re - create the entire original scores in C and D on a hard drive.

  (1) the hard disk (in GB) must be the same size or larger

  (2) search the original hardware configuration. You have not changed the hardware cards.

• How to create a toolbar of shortcuts on the desktop

  Hello...
  How to create a toolbar of shortcuts on the desktop
  

  Unfortunately, this feature is no longer available with Windows 7. I was surprised myself so since Vista was fine with it, but in Windows 7, we all need to just get used to using the feature of the taskbar QuickLaunch. You can pin any icon you want in the taskbar and use it to your quick launch of this program.

• How to create a file name variable with the County and the date?

  Objective: Create a file name variable with the County and the date

  Error: get a lot of error. Do you know how to change my code?

  Question: how to create a file name variable with the County and the date?

  Mini code:

  std::string * rawfilepath;
  std::string * rawfilename;

  rawfilepath = "./shared/documents/";
  RawFileName = rawfilepath + 'rawlog -' + 0 + '-.txt ';
  QFile file (rawfilename);
  If (file.exists ()) {}
  rawfilenamecount ++;
  RawFileName = "./shared/documents/rawlog-" + rawfilenamecount + "-.txt ';
  }

  Thank you for your attention,

  Thank tzander reminding me the idea. Method of cascades is not good for me because all of the kernel code is written by Native. If I change the channel to QString, I need to change a lot of codes.

  Solution is below.

  While (access (rawfilename, F_OK)! = - 1) {}
  rawfilenamecount ++;
  sprintf (format, RawFileName, rawfilenamecount);
  fprintf (stderr, "file exists");
  }

  Rawlog = fopen (rawfilename, "w"); Save the file in a specific path.
  fprintf (rawlog, "System Time (ms)" "");

• How to create a VPN file .pcf for the CISCO VPN CLIENT software profile

  Dear all

  How to create a VPN file .pcf for the CISCO VPN CLIENT software profile

  Concerning

  Hi Imran,

  Can't do much about that because it depends on what authenticate you the VPN server and how the settings. But let me introduce you to the memory layout. Once you install and open a VPN client. Press it again and it opens up a new page for the VPN config.

  Example of configuration as it is attached. But it differs depending on the configuration of your vpn server.

  Once you create and save this profile. Your FCP file is stored.

  Please assess whether the information provided is useful.

  By

  Knockaert

• How to create a user local administrator with the user root on the CV

  As says the tile, how to create a user local administrator with the user root on VCS-Express. I lost the password and cannot log in as an admin user, but I can't seem to log as long as user root.

  Once connect you with the root account, type in "tsh", from there, you can create the accounts of local administrators with 'xCommand AdminAccountAdd.  See the reference section of command of the VCS Administrator's Guide, starting on pg 517.

  If your VCS is a virtual machine, you can change the password of admin with vSphere, or if it is a hardware appliance, you can use the serial port, see pg 312 of the Administrator's guide.

• How to create a my Signature (signature with the tablet of manufacturing) Action?

  How to create a my Signature (signature with the tablet of manufacturing) Action?

  I use PSCS6?

  I have no problem making an action of signature if I pick a font and then type in my name,

  but to make a real action of my signature seems impossible.

  Hello

  There is a very cool technique to do by your signature in a Photoshop brush.  Once this is a brush, you can change the size and place the signature everywhere where you want.

  Google "Photoshop brush signature" or something similar and you will see a lot of tutorials.  Try this one:

  Photoshop reference guide | Creating a custom brush Signature | Peachpit

  Basically, you sign your signature on a blank piece of paper, then you scan in a JPG or TIFF file, then you open that file in PS to create a brush.

  I hope this helps.

  John

• How to create grainy texturing and faces in the movie posters

  I love watching the lighting and contrast in the movie posters,

  I would like to know how to create textures and texture effects I see often on movie posters, which seem more hyper made realistic than nature, still convey the character very well skin, I have also attached a cover of wii games to show the hand texturing,

  My guess is that it's done with the right give modes and texture brushes, do not know how to create this subtle grainsand looking into the skin, or what is a very good camera that captures the skin in detail then applied to the skin texture, contrast? benjamin button seems to have a grain for its halftone,

  benjamin and prince of Persia poster button seem to capture better what I mean, hand on the cover of NFL wii game is also interesting.

  a few examples below,

  

  

  

  

  Make a new layer filled with 50% gray, use the filter-> noise-> add noise or other texturing method you prefer and then change the blending mode of this layer to overlay or soft light.

• How to create users that can connect to the application?

  Hello
  
  
  As an example of Application provided by APEX, in this application, the administrator can create users and reset passwords, and the user can connect to this application. How is this happening?
  
  Now I know how to create users and reset passwords through the corresponding working table.
  
  But I don't know how to use the user to to connect to the application? I tried several times to use the user create by ADMIN to connect to the application, but I failed.
  
  I can't find any setting in the sample Application, but it do.
  
  If any good plans?
  
  I thank in advance.

  There are two ways you can handle this... Build users of the APEX and continued them through the api of the APEX (not recommended by what I saw several comments here, outside the development environment) OR in your application, you could build a custom authentication system...

  Here is a link to explain how make one:
  http://djmein.blogspot.com/2007/07/custom-authentication-authorisation.html

  Thank you

  Tony Miller
  Webster, TX