How to fix the device of ata tsstcorp ts l - 633 b
can get tssp corp ts l - 633 b ata device to work answers
Hello
Step 1: Please do all the same underneath if you did some before as is often total
a process that solves the problem.
Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
below.
Then, work your way through these - don't forget the drive might be bad, could be a coward
cable or slight corrosion on the contacts (usually for a laptop) and other issues.
Your CD or DVD drive is missing or is not recognized by Windows or other programs
http://support.microsoft.com/kb/314060 - a Mr Fixit
Try this fix manually if the Fixit 314060 does not work
http://www.pchell.com/hardware/cd_drive_error_code_39.shtml
Your CD or DVD drive is missing or is not recognized by Windows or other programs-
a Mr Fixit
http://support.Microsoft.com/kb/982116
The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
for Windows Vista
http://support.Microsoft.com/kb/929461
When you insert a CD or a DVD, Windows Vista may not recognize the disc
http://support.Microsoft.com/kb/939052
Your CD or DVD drive cannot read or write media - A Mr Fixit
http://support.Microsoft.com/GP/cd_dvd_drive_problems
CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
Vista installation after booting from the DVD (AHCI)
http://support.Microsoft.com/kb/952951
Drive CD - R or CD - RW Drive is not recognized as a recordable device
http://support.Microsoft.com/kb/316529/
Hardware devices not detected or not working - A Mr Fixit
http://support.Microsoft.com/GP/hardware_device_problems
Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
ends. Remove and replace, do not just tight. For laptops, you can often clean power and
contacts data with a pencil eraser.
Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
manufacturer of device to see if there is a firmware or drivers for your drive if necessary.
===============================
Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
do it right.
Did you follow the Troubleshooting Guide for the reader who still does not work? There are
the entries in registry that the troubleshooter does not solve and those who "might" be the cause.
Check with your Maker system and a device for the two possible firmware updates and
the correct registry entries for your car.
Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
the parameters.
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}
-----------------------------------------------------------------------
You can probably find more info here and maybe even the exact registry for your CD/DVD settings
drive from someone with the same model.
Forums - a lot of expert real help
http://Club.myce.com/
CD/DVD units
http://www.myce.com/storage/
Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
nothing change) - find the DevManView device and then make a right click on it free in RegEdit.
DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
devices and their properties in flat table, instead of the tree viewer
http://www.NirSoft.NET/utils/device_manager_view.html
I hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">->
Tags: Windows
Similar Questions
-
How to fix the black screen of my hp pavilion g6
How to fix the black screen of my hp pavilion g6
Try a hard reset, works sometimes. Disconnect all external devices first.
battery and power cord 1 / removal
2 - Press the power button for 30 seconds
3 reinstall only the power cord for the first start.
4. turn on
-
How to fix the below errors event-7001
How to fix the below errors event-7001. Because my PC Win7 OS frozen when start as msg 'Welcome '.
The computer browser service depends on the Server service which failed to start because of the following error:
The dependency service or group was able to start. Event ID is 7001.Hello
Try to fix this problem by doing this
- Open the Device Manager.
- On the view menu, click to select the check box Show hidden devices .
- Double-click drivers Non Plug-and-Play.
- Double-click NetBIOS over TCP/IP.
- In the use of the device box, click use this device (enabled).
Hope this helps
James
-
How to fix the missing text and updated lines shaped, hyphenated words and patterns disrupted, lost after export PDF document to word doc to allow editing? using WPS office application on Android Galaxy tablet. tried Polaris app and got a blank document.
Thank you!
Hi Spider,
Adobe Acrobat on mobile devices can be used for editing. I will suggest you to perform the task on PC or Mac.
Thank you
Abhishek
-
Hello
Dose anyone know how to fix the error with the code: 0xe7210001, message: unable to load powrprof, object: CLSD-no-it is found;
OR: Fingerprintsoftware OR error: replicas THotkey.exe message window and the computer freezesMaleware scanned and virus, also in safe mode, found no infection, reinstalled driver fingerprint, but nothing has changed.
grateful for the help!
Hello
> message: unable to load powrprof, object: CLSD-no-it is found;
In my view, this would mean that there is a problem with Toshiba Power Saver
What laptop Toshiba, you have exactly?Maybe reinstall Power Saver could help. You can find it on the official website of Toshiba.
-
How to fix the main button to paste constantly
How to fix the main button to paste constantly
Short of getting a replacement from Apple or risk a repair third shop there is nothing you can do. How about a button on the home screen? Go to settings > general > accessibility > assistive touch > on.
-
How to fix the bug of 1970 on iPad mini 2
How to fix the bug of 1970 on iPad mini 2
It is not a bug. It is the result of a deliberate action by the user. However, some reported that the DFU restore, if it does not, then you must make an appointment at the Genius Bar at the Apple Store closest to him have supported. Apple is working on an update that will prevent users from doing it again. If you changed the date to May 1970 or earlier and he can't restart your iPhone, iPad or iPod touch - Apple Support
-
How to fix the microphone in Compaq Presario R3000
Original thread title - how to fix the microphone in Compaq Presario R3000?
Hello
I have a laptop Compaq Presario R3000, and I tried to use Skype on it. Problem is that the other end can't hear me. I tried all the suggestions on the site of Skype to try and attach the microphone. I tried the recorder (click programs, accessories, then entertainment to access), but when I record my voice, nothing, so I guess it has something to do with the microphone. Just to be sure - this model has an internal microphone? What I've read, it seems that it does. I downloaded the updated drivers, so I don't think that's the problem. Any suggestions? I'll try anything now, because I spent about 6 hours online trying to get the microphone to work and so far, nothing. Thank you! PattiHello
1. What problem is only on Skype?
2. were you able to use this microphone earlier?
3 have there been any changes made on the computer before the show?
4. what operating system are you using on your computer?
I suggest you to consult the steps mentioned below and check if it helps.
Run the troubleshooter of sound recording
Click on the link below and run the troubleshooter.
http://Windows.Microsoft.com/en-us/Windows7/open-the-recording-audio-TroubleshooterSee the following Help article.
Tips for solving common audio problems
http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-sound-problems
No sound in Windows
http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows
If the problem persists, then I suggest you to contact Skype to get help.
It may be useful
-
How to find the device ID?
How to find the device of my CAN ID card and RIO (or card for something else)?
I use MAX 4.5 and LabView 8.6.
Thank you.
Open MAX and go to the section:
My system > devices and Interfaces > NOR-DAQmx
It should list all your DAQ devices and say something like
DAQCard-xxxx: "Dev 0.
DAQCard-xxxx: "Dev 1.
etc.
Just look at your device
-
Problems of updates Windows XP - how to fix the incorrect Windows XP updates KB2633952 keep asking to install? True, it is that it is already installed on your computer. If hide us, an another previous KB2570791 arises in our updates of Windows and asked to install anything, that it was installed... of the questions repeated and very annoying. Help, please!
(Microsoft Answers just sent us message have deleted our previous thread, ask for help!) We are simply not that these problems are problems with Windows XP updates related to DST or not?)
Nadia. PA supporter said that your computer is hacked. He may be right. I can't weigh because I don't know what led him to this conclusion. If your computer is hijacked, then you should address that more that you need to fix this minor update. However, under the resolution of your problem to update, you can try this:
Assume Windows XP
Check the C:\Windows\System32\ directory for the presence of the file tzchange.exe
If the file is not present or if the version of the file is not 5.1.2600.6171 or newer...
Download the update appropriate 2633952 for your platform here:
http://support.Microsoft.com/kb/2633952
Run with - extract switch (e.g., Start > run > "[path to the downloaded file] \WindowsXP-KB2633952-x86-ENU.exe"-x)
Of course, replace [path to the downloaded file] with the path to the downloaded file.
Citations may or may not be required depending on the path. Place the x - out the citations if you use them.
Choose a location for the extracted files (a new folder is recommended)
Locate the extracted files. File tzchange.exe you want and copy it into C:\windows\System32
That rerun Windows Update detection to see if the problem is resolved.
-
G530 - how to fix the Novo key features?
Hello guys!
Some time ago I completely changed partitions configuration on my laptop, because I wanted to have two systems - Windows 7 (the default) and Ubuntu. Previously, I had an image of the LENOVO_PART (partition Lenovo recovery) by Paragon and burned on DVDs. Its contain images (a recovery key 7) OKR - mbr, boot partition and system (with default settings) file that contains information about the partition sizes and sectors. I deleted all the partitions and create new partitions.
Now I want to restore the original scores, so I restored the partition recovery DVDs, and I put his ID 12 (PTEDIT32) and rebuilt the other partitions on the accuracy of a sector.
Now, I have the following partitions: 1 - start (default is unnamed), 2 - system (default is unnamed), 3 - Lenovo, 4 - LENOVO_PART. Unfortunately the Lenovo System Restore does not start once I pressed the Novo key, so I put the active recovery partition and I can't restore the original mbr, boot, and system. Everything would be fine, but the Novo key doesn't work, then press start the normal system of Windows 7, not the recovery system.
Could someone tell me how could fix the Novo key without the Lenovo service features?
BTW, sorry for my bad English
It should work properly. It seems that there is something wrong with the a key.
at this point, I suggest you call lenovo support line and ship your laptop.
-
How to fix the position of the cmd window?
I would like to know how to fix the position of the cmd window on the upper right corner instead of middle of anywhere in the window.
Does anyone have any suggestions?
Thanks in advance for your suggestionsHello!
Open "Command Prompt", right-click the title bar and choose "Properties".
Go to the Layout tab.
In terms of the "Position of the window", uncheck "Let system position window.
Change the Left and Top values to your preference - on my system (left = 290, Top = 0) are ok.
On the same tab, look at the picture under "Overview of the window" to try different values - the window position changes after entering a value in the left text box and pressing the tab key.
I hope that helps!
-
How to change the device profile.
Hi all
How to change the device profile. I mean from "Normal" to "Enough" or part of the profile.
Can someone help me in this?
-Shekhar.
It is not possible by programming
-
How to use the device as a simulator.
Hi all
Can someone tell me how to use the device (with my development pc) as Simulator.
Whenever I need to check the appilcation in device of signed files .cod that is compiled in the Simulator.
Because I got the outofmemory error in the device rather than simulator.
Thus, any solution which signed without how can I check my direct request to the device itself. Any setting in preferences or etc...
Thank you
Tejas
The only way you should not sign the cod is if no controlled classes/interfaces are used. The easy way to find out is to open the SignatureTool and see if your application requires signature. Otherwise this says icefrost1 's good enough solution.
-
How to fix the rotation in application as apply just open land scrap only mode in Html5
Dear team,
I develop application using HTML5 for Z10.
How to fix the rotation in application as apply just open land scrap only mode in Html5
Please help me and give me a link to the documentation for this.
Kind regards
HP
Hello
You can set the following in your config.xml file
There is more information available on our developer site -https://developer.blackberry.com/html5/documentation/code_sample_creating_a_bb_widget_config_documen...
Maybe you are looking for
-
HP Pavilion 71 tour will not come
I have a HP Pavilion 71 that I bought new when I custom built my computer with two hard drives & CyberPower surge protector, 4 years ago. Two weeks ago Entergy cut electricity in our area for 15 minutes. I went to turn on my computer and the reset
-
Satellite L10-114 graphics memory
I have the l10-114, which, according to the specifications on the tosh site should support shared memory up to 64 MB video memory. However, I can only choose a maximum of 32 MB in the bios. I have the latest available bios version. is it a typing mis
-
Cams has supported to post real-time monitors?
Hello I was watching the camileo cams.Supports any one of them hang a direct on an external monitorNOT for playback of recorded images, but as a _live_ extract. (even if not recording) If the TV cannot, which cam can? =) Thank you!
-
Satellite P200D-128 - Question about installed Norton anti-virus
Hi, I bought a Toshiba Satellite P200D-128 last week and to say I'm majorly annoyed with Toshiba would be an understatement, and that understatement. Fine machine autoinstalled as its operating system, and I found I had Norton anti-virus installed, o
-
Transfer files from a dead computer
I got a Dell Dimension 2300 with Windows XP. So I took the hard drive and placed in a box HD is no longer usable. I just wanted to get some of her files because they are very important. I have plugged and don't know what I'm doing. How can I recover