How to mount a polynomial if waveform to XY cluster is present

Similar Questions

• How to calculate the polynomial graphic adjustment of waveform

  Hi all

  I am new to lab - view so would need a little assistance in one of the problem I have right now.

  My problem is: how to calculate the polynomial graph of waveform data adjustment? I need to convert the waveform to XY graph data, and then use the polynomial vi made integrated to calculate the fitting?

  Detail: My problem is that I have waveform graph, I calculate the vertices and the Valley, but because of the noise, my peaks and Valley detection is sometimes not exact, so to smooth the chart that I must apply the polynomial fit.

  If anyone can help me in this, I'll be very grateful.

  Thanks in advance

  Hi Omar,.

  have you seen the suggestion of Lynn above?

  You already have the values of Y (your table). Now, you need build the table of X as indicated, only to replace the value of dt with your spacing from point to point. Somewhere in your code, you know that the value that you have an x-axis indicated in milliseconds...

  

• How to convert the substring to waveform

  Hello

  I have an input file with a lot of numbers that need to be converted to a waveform. I used the match model vi to extract the data I need to be traced out. These data can be seen in 'before the substring"but I do not know how to convert these data to waveform. Can anyone help? I have attached the input file and the vi as well. Thank you

  Try using the worksheet File.vi reading. It converts a text file delimited by tab characters in a table of numbers in one step.

  Lynn

• How to mount the virtual folder of the ILO on ESXi 5.5

  Hi all

  Anyone know how to mount the virtual folder of the ILO on ESXi5.5?

  What is the command that I should do the editing?

  Usually in Linux or Windows, if you clicked on the virtual drivers on HP iLO web interface, you will see the mounted folder automatically in the operating system.

  But I don't know how it would be or how to have the same functionality in ESXi host. Can anyone help?

  Thank you.

  Try to use the "vsish" method I describe in this post.

  Re: New drivers enter ESXi

  See you soon,.

  Jon

• How to mount the iso image on the ESXi Tech support console

  Hi friend

  How to mount the iso image on the ESXi Tech support console?

  I run the sub command and it failed.

  # mount o loop-t iso9660 vmware-esx-drivers-net-be2net_400.2.102.440.0-1vmw.2.17.249663.292682.iso / free

  editing: vmware-esx-drivers-net-be2net_400.2.102.440.0-1vmw.2.17.249663.292682.iso mounting on / open failed: no such device

  ESXi does not provide the option of mounting ISOs. You try to install the driver the driver Async package be2net / ISO. Follow the steps below

  (1) install VCLI
  (2) mount the ISO on the host where you installed vcli
  (3) use vihostupdate to install the driver
  vihostupdate-i b - servername
  He will ask for username and password of your host.

  Thank you
  Nithin

• How to display more than two waveforms on a waveform graph?

  Well, I have a question in the basics of waveform graphs. I have to post four waveforms simultaneously in my program. I can see two graphs on it, but when I try to display four waveforms, I get an error:

  You have two or more data types of cluster wired together, but clusters have different types or numbers of items.
  Cluster (unnamed), a group of 3 elements.
  conflicts with graphic waveform cluster, a cluster of 2 elements.

  Is there anyway that I can change a graphic in waveform to a cluster of 4 elements? Because I borrowed this waveform of a VI example on waveform cards "Charts.vi", so I guess it must have been programmed to be a cluster of 2 elements.

  I hope that I have my question clearly.

  Thanks in advance

  One of the problems that you have is that data from the DAQ assistant has a time stamp from now which is about 3 billion seconds

  Data from the simulated signals has a time stamp based on the beginning of the acquisition which is about 0 seconds.

  So, the table needs to be stretched early in LabVIEW time now to show all the data.

  Change signals simulated so that the timestamp is the result of an absolute time, then you should be able to see all the signals.

• How many nodes can be added to the RAC cluster

  My colleagues asked me how many nodes can be added to the RAC cluster.
  I'm not concerned about this issue, but I would like to know it.
  I would be grateful if someone let me know it.
  
  Published by: adenkang on November 4, 2009 20:00

  As close and as much as I know, the number is limited mostly by the used clusterware.
  At the same time, Oracle clusterware in Oracle 10 g 2 supports up to 100 knots.
  A lot of information about this is @metalink in 220970.1 CARS: frequently asked Questions

• How to mount SD card in secure boot mode

  I have a problem with my Imac where I can start only in secure boot mode. The problem is that in safe safe mode SD card not only mount. I need the contents of the SD card. How can I manually force the SD card to get?

  There are some things that don't work in Mode without failure.

  See note in the article here, try safe mode if your Mac does not commissioning - Apple support.

  More specifically,.

  For example, these features do not work in safe mode:

  • You can not play movies in the DVD player.
  • You cannot capture video in iMovie and some other video applications.
  • An input audio or output devices may not work.
  • Some devices USB, FireWire, and Thunderbolt is not available.
  • Wi - Fi networks may be limited or unavailable depending on the Mac and OS X versions you are using.

  If your Mac starts in Mode safe, but not normally, it is probably because you have installed a third-party software that prevents the normal start upward. If you remove this software when you're booted without failure, you should be able to start normally. Some common software that will always give you problems: everything that is supposed to clean, optimize, protect, purge, control or maintain if your Mac.

• How to continually take and record waveforms with neither 5102

  a machine generates waves sinusoidal time randomly. I want to permanently take and record waveforms in 10s by NI 5102.

  How to do?

  Thank you very much!!

  Thanks for the review! but this isn't a supported NEITHER.

  I record signals by this method.

  and the promble news is that different sampling frequency, the different wavelength. for example, when I put the sampling frequency is 4 k, the wavelength is 12 seconds if the sampling frequency is 10 k, the wavelength is 8 seconds the signal under test 1 k, the time constant is 10000.

  now, I save waveform to 10 sec. What is the best relationship between sampling frequency and the time constant?

• How can I write a digital waveform to the digital output (traditional DAQ)

  Hello

  I use a NI 6023e, PCI, with 8 digital outputs. I generated a digital waveform. How can I write for a specific digital production line now?

  I only have Labview 7, so I can't use DAQmx.

  Thank you very much

  
  

• How to create the type of waveform data

  Hello

  I work with the oscilloscope TDS 30xx series and I want to create the data type of waveform in the waveform of Fetch VI.

  I have problems with that. Can someone help me?

  I don't know how to data table of waveform to the creation of a data type.

  Is attached a photo of the VI and the VI himself

  Well, if you want to build a waveform of Y, dT and T0, you can still use the function named "build the waveform.

  

• How to effectively create a single waveform based on data from two other waveforms?

  I have a table 1 d of waveform with size = 4 which contain data of voltage potentiometer "gross".  I need to handle index 0 & 1 waveform data using the formula below to calculate a single waveform of angle data.   I need to do the same for the 2 & 3 index because it is a redundant circuit.   I was hoping that the formula node can operate on whole berries and even if it may take a table as input, it asks me to the array index in the formula so that it becomes a scalar value.

  As the formula is quite complex, I would like to keep as text, but run automatically on each point of the two input tables.  This math is done online with pulling data from a data acquisition and so I need it to be as effective as possible, so that I do not spend too much time on it and likely to overflow the buffer DAQ.

  The naïve solution would be to wrap nodes formulas with curls, but I don't know if it is this is an effective way to do it.  I'd like suggestions on how best to address this issue.

  Thank you!

  

  Here's how I would do it with no formula requires knots or loops:

  

  If you want to use the formula node, you can then run a loop inside each node formula while the index of you through the berries.  The difference in performance between the nodes of the formulas and graphic approach expected to be negligible.  Note that my approach assumes that the table sizes are the same.  You can also create a sub VI to contain the math so you don't have to maintain two copies of the same piece of code.

  Chris M

• How to mount an ISO image with Windows 8?

  I use Windows 8 Pro x 64.

  How can I mount a file ISO in WIndows 8?
  I right click on the ISO file and the menu that opens does not give me an option of editing.  It says at the top of the game menu.  There is no an option of editing anywhere in the menu.  I looked into the open with option, but the Assembly isn't here either.

  Have you tried the following?

  Right click on a .iso file > properties > click "Edit" under the "Général" tab > click on "Windows Explorer" > OK

• New to first... How to still see the audio waveform when dragging a clip?

  I just installed the trial of first Pro CC and trying to familiarize myself with the program. I can't find how to make the audio waveform visible while dragging a clip, so that I can synchronize with other audio waveform. Thank you.

  Hi Avène,

  AFAIK, you can't see the waveform by dragging, but a faster and more accurate way would be not not to drag, but to familiarize themselves with the hotkeys to clips slip and slide

  and use for this task: (you see the waveform by pushing, dragging and dragging)

  These are the default shortcuts:

  	PC	MAC
  Drag the Clip left selection five images	ALT + SHIFT +.	Opt + shift +.
  Drag the Clip left selection an image	ALT +.	Opt +.
  Drag the Clip right selection five images	ALT + SHIFT +.	Opt + shift +.
  Selection of right slide Clip an image	ALT +.	Opt +.
  Slip Clip left selection five images	CTRL + Alt + Shift + left	Opt + Cmd + Shift + left
  Slip Clip left selection of an image	CTRL + Alt + left	Opt + Cmd + left
  Clip of slip right selection five images	CTRL + Alt + shift + right	Opt + Cmd + shift + right
  Selection of Clip of slip on the right a picture	CTRL + Alt + right	Opt + Cmd + right

  Move the Clip selection left five images	ALT + SHIFT + left	Command + shift + left
  Move the Clip left selection an image	ALT + left	Cmd + left
  Move the Clip right selection five images	ALT + SHIFT + right	Command + shift + right
  Selection of boost right of an image Clip	ALT + right	Cmd + right

  Once you understand these controls, you align clips much faster and easier!

  good resources:

  https://www.video2brain.com/en/lessons/keyboard-shortcut-changes-1

  repositioning, slide, slide starts at about 03:50, but I suggest, you look at all this.

  and:

  Adobe Premiere Pro help. Trimming clips

  .. .hope that helps, otherwise just come back here if you still have questions

  Greetings, felix

• How to mount an ISO file

  Guys,

  I'm pretty new on the VMWare environment so apologizes in advance for what might seem basic questions.

  I want to mount an ISO of Windows 2008 file in the client VSphere 4.1.

  Now when I Googled what he tells me to open a command prompt at the host and use the Assembly tool.

  First question is I see a list of virtual machines, built by a previous contractor who took the site for reasons that I will not.

  When I do a right click of the mouse I have a console open for each virtual machine, but what I want to do is mount an ISO file of windows 2008, so I can build a new virtual machine.

  I see a name and an icon called VMCluster and under that 3 servers then under all virtual machines.

  What I see is an option to go to the command line to mount the ISO file.

  Can anyone please tellme how to proceed?

  Thank you

  Fred

  Do you mean you want to mount the ISO in a virtual machine on a host?

  If so, there are several ways to do so.

  Best way to demonstrate would be: right click on the virtual machine, select "Open Console" and then in the top bar look for the icon that appears to be a CD. Click on this icon, select the CD/DVD drive and select "connect to the ISO image on the local disk.

  A picture is attached below to demonstrate.