How to read and display the .ai file in CS4 SDK?

Similar Questions

• How to read and display a my a miccrontroller (MCB1700) on labview signal connected via a port on a PXI machine CAN

  How to read and display a my a miccrontroller (MCB1700) on labview signal connected via a port on a machine PXI CAN?

  I tried using a DAQ Assistant, but the port is not included as one of the physical channels supported, even if all his drivers are up to date.

  Help, please...

  Thank you.

  If you can read it in MAX, then you should be able to run the NI CAN example.

  Help-> find examples

  Find the CAN and watch CAN Receive.vi.

  Basically, set up the network, open the object, read in a loop close object when it is done.

  If you have any questions about the example, go ahead and post your vi and we can work from there.

• When I plug my portable hard drive to the usb port it does not read and display the contents...

  When I plug my portable hard drive to the usb port it does not read and display the contents...

  Hi deaza,.

  Ø Have you connected the USB hard drive to the computer directly or you have used an external USB hub to connect?

  O trying to connect to another USB port to check if it works?

  O the hardrive shows in windows of the computer when you connect it?

  Method 1:
  If you have installed security software, I suggest you to temporarily disable the security software and connect the USB and check to see if the same problem happens. Make sure that you enable the security software after checking.

  Alternatively, you can try to plug the USB key into a different USB port and check if it helps.

  Method 2:
  I suggest trying to launch hardware and troubleshooting of devices and check to see if it helps, here is the link:http://windows.microsoft.com/en-US/windows7/What-to-do-when-a-device-isn ' t-installed-correctly

  Method 3:
  If this does not help, then follow these steps:

  (a) remove all your USB devices. Use the safely remove the feature to turn them off.

  (b) open Device Manager and navigate to the section for USB. Uninstall all USB drives. There should be one for each USB port, and then restart.

  To open Device Manager, go to the link below and follow the steps:

  http://Windows.Microsoft.com/en-us/Windows7/open-Device-Manager

  (c) Windows should re - find all of the devices. If it is not the case, note the error message and let us know.

  You can also navigate to the link below and follow the steps to install the USB device.

  http://Windows.Microsoft.com/en-us/Windows7/install-a-USB-device

  I hope this helps. Let us know the results.

  Thank you and best regards,

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• How to read and understand the information in the event logs

  Hey Microsoft, I performed a task of Information on performance. I have several criticisms and doubtful window logs in Event Viewer that is as much affect performance. I don't understand all the information on how to deal with them as I have not very in computer science. Can you please tell me how I deal/delete and those to save using total evidence silly English. There is also an application firewall re being not recognized even if I have AVG and Works installed.

  Thanks for your help.

  OT: EVENT LOGS

  Hello LadyWilliamson,

  Click on this article which describes the event logs in Windows XP. Most of the information is still topical for Windows Vista and Windows 7.
  308427 KB - how to view and manage the event logs in Event Viewer in Windows XP

  
  Click on this site Microsoft Web is for Windows event logs 7
   
  Vijay B information should answer your other questions.

  Thank you

  Marilyn

• How use the serial port read and display the text but not scroll off the screen?

  I'm new-ish/return user fan of Labview and trying to change the example VI "Advanced serial write and read VI" is the part of the dev suite 2012.  I need to use the string box for ALL of the text from a serial port, always adding and just roll off the screen when the actuals come to the serial port.

  What actually arrived more than bytes (or no bytes AT ALL!), during reading time text, current rolls out of the box in the chain.  Even when receiving 0 bytes, screen is removed.  I'm not very familiar with the locations of functions and even worse to understand obscure references to functions, so please keep very basic answers so I can follow.

  Just to be clear, I need window of the chain behave as HyperTerminal does always displays the data and it is not pushed by window arbitrarily.

  Thank you

  Steve

  A long shot.

  Is that what you want?

• How to read and write a text file to the folder of the user preferences?

  I'm trying to code for the user to record the plug-in, the first time that the user opens Acrobat after you have installed the plug-in. I want to write a file of registration of preference of the user folder access later to check that they are already registered.

  Is there an easy way to do this? I wrote the code to access the preference of the user folder to search for the file, but I have not been able to code for the write file. All I've found is how to write a PDF file.

  Any suggestions?

  Gregory

  ASFileRead/ASFileWrite

• Image: poster of local disk, download server and display the server file system

  Hello

  I use jdev 11.1.2.4.0...

  The requirement is that users want to upload images to their local drive for the drive on the server and they would like display of server disk images later.

  We do not want to save the images in the database. I'm not sure what should be the solution; However, I intend to...

  1 create a table to keep information from images - image_id, image_location (server drive), image_filename

  2. create a page where users can enter image information and specific file on a local disk name (I think I'll use inputFile component) and provide the Preview button to display an image on the screen before saving. To record data is to save the information in the database and copy an image file on the disk on server (the location for image files is predefined.)

  3. create another page where users can browse the database information and display an image for a selected record getting from the server.

  I need suggestions on...

  1. how to display an image on the page of the local drive?

  2. how to copy a file on a local disk to a server?

  3. how to display an image on the page of the drive on the server?

  Thank you.

  NAT

  See:

  http://tompeez.WordPress.com/2011/11/26/jdev11-1-2-1-0-handling-imagesfiles-in-ADF-part-1/

  http://tompeez.WordPress.com/2011/11/26/jdev11-1-2-1-0-handling-imagesfiles-in-ADF-part-2/

  http://tompeez.WordPress.com/2011/12/16/jdev11-1-2-1-0-handling-imagesfiles-in-ADF-part-3/

  When Timo records the images in the database, you save it in the file system (examples on how to do this Java are available much if you just Google for it). Similar to Timo you then use the tag image to display pictures. The difference is that you can directly add the URL of the database table.

  The advantage of using a database to host images, it's that you're not although dependent on files server structures

  Frank

• How to capture and display the end of line character in the report

  Hi guys,.
  
  I have a report that we are poster campaign ID, campaign name, and Description of the campaign.
  The result is coming like this
  
  Description of campaign campaign campaign ID name
  1 ABC 1 Plan June 13. 2 market July 1. 3. end July 30.
  Plan XYZ 2 1 13 June. 2 market July 1. 3. end July 30.
  
  But we want the data to be displayed in the following format.
  
  Description of campaign campaign campaign ID name
  1 ABC 1 Plan June 13.
  2 market July 1.
  3. end July 30.
  Plan XYZ 2 1 13 June.
  2 market July 1.
  3. end July 30.
  That the user has the possibility to enter several lines for the description in front end Application & want us to show the same way Description. How can I capture this end of the character in ETL? If he is already captured, then how to show in the report.
  I use Siebel as before end application and for the ETL using Informatica.
  
  Any help will be much appreciated.
  
  Thank you
  Rupesh

  OBIEE presentation Service is an HTML element based on software then it does not show the end file character CHR (10) or Chr (13).
  You must replace this with the HTML tag charcaters
  .

  I'm not sure of the name of the function, but you must make a formula like this

  replace(mytable.mycolumn, chr(10), '
  ')
  

  See you soon
  Nico

• How to locate and remove the attachment file to the Inbox folder?

  Hello

  My name is Piotr Tyborowski and I am the Doctor Web's Technical Support Engineer.
  I had such application suport - one of our customers has problem with viruses in Thunderbird Inbox folder - our antivirus scanner has found two Trojan horses in a file located in the Inbox folder and moved all of the Inbox folder to quarantine. We know that these files can be found here:

  > > C:\Users\Renatrix\AppData\Roaming\Thunderbird\Profiles\4dhjzo2v.default\Mail\Local Folders\Inbox.sbd\Konto WP\12145.part is ZIP archive
  C:\Users\Renatrix\AppData\Roaming\Thunderbird\Profiles\4dhjzo2v.default\Mail\Local Folders\Inbox.sbd\Konto WP\12145.part\KeyDLL.dll - Trojan.KeyLogger.6153-infected
  C:\Users\Renatrix\AppData\Roaming\Thunderbird\Profiles\4dhjzo2v.default\Mail\Local Folders\Inbox.sbd\Konto WP\12145.part\KeyDLL.dll - infected
  > > > C:\Users\Renatrix\AppData\Roaming\Thunderbird\Profiles\4dhjzo2v.default\Mail\Local Folders\Inbox.sbd\Konto WP\12145.part\svhosts.exe - compressed by UPX
  C:\Users\Renatrix\AppData\Roaming\Thunderbird\Profiles\4dhjzo2v.default\Mail\Local Folders\Inbox.sbd\Konto WP\12145.part\svhosts.exe - Trojan.Click.27588-infected
  C:\Users\Renatrix\AppData\Roaming\Thunderbird\Profiles\4dhjzo2v.default\Mail\Local Folders\Inbox.sbd\Konto WP\12145.part\svhosts.exe - infected
  C:\Users\Renatrix\AppData\Roaming\Thunderbird\Profiles\4dhjzo2v.default\Mail\Local Folders\Inbox.sbd\Konto WP\12145.part - archive infected

  I'm not very familiar with Thunderbird, so my question is - is is possible to get this file 12145.part and remove it as well, even with the message that cointains inside?

  Thank you in advance and Best Regards,.

  Piotr Tyborowski
  Doctor Web

  Piotr,

  If it's convenient, the absolutely safest approach is to delete the profile folder 4dhjzo2v.default while integer that TB is arrested.

  If the person is to use IMAP or POP with an option to leave emails on the server, there should not be a loss of emails (except in local folders).

  If there are important e-mails in local folders, and they are not infected, they could be exported to support storage and then imported into the new profile. There is an add-on to tuberculosis, which allows the import and export of emails in different formats.

  You will find instructions on how to download and install it in http://barryduggan.info/exportMail.php

• My document Pages when sent in PDF format opens with Acrobat Reader and displays the text pane

  Hey team

  I am a new user of recent Mac and I have some difficulty with the Pages.

  I'll create a new document and save it as a PDF file (save it to the desktop), when I open it again, it opens with Acrobat Reader and the text released along side this one pane. It does not open a document own stand alone. This cause me a problem when I want to send it as an attachment, as it includes this component, as well as all other toolbars with.

  Any help on this would be appreciated.

  SSA56,

  When you send the PDF document as an attachment, it will be sent as a document 'stand alone '. It will be open according to the preferences that are set by the receiving party.

  

• 5 Lightroom can't read and import the raw file

  I can't import my RAW files from my Nikon D750. When I try to import my SD card, I am able to see the preview, but when I try to import, I get a window that reads "the following files were imported not because they could not be read. I haven't changed anything on my camera on the LR5 parameters settings and this happened just today. I am able to transfer the files on my desk at the moment, but I can't yet import from there. I also tried reformatting the card and even tried another card so I don't think that the problem is the card or the device itself. I also do not seem to see updates that I need. Does anyone have any suggestions?

  As noted of Claes, it is almost certainly a problem with your destination set wrong in the import Panel. This happens quite easily. You get the error message is almost always due to the destination without folder do not write access. Really check your destination. This should NOT be the root of your startup for example disk level and for some reason any sometimes default Lightroom at this place and then refuses to import because the OS refuses to let you write here.

• Need to re - register a completed form on in Acrobat Reader and keep the same file name.

  I did collect a form developed for our client in. They need to access and save it several times without making several versions.

  Now that they can open, fill out some fields and "save under" a different file name. They must then go back and edit or add additional information to train at a later date.

  He won't let not the re - save the file with the same file name, only "save under". It is not very practical because they will end up with many versions of the same shape and all earlier versions would be obsolete and useless for them.

  You must disable the preview in Windows Explorer or close Windows Explorer.

• How to import and display a .tif file?

  I imported a .tif file by reference, as I have done hundreds of times before with .jpg. Looks like it's important, but what I see on my page is a white square. However, I can resize the image to scale it (i.e. it looks like a graphics card is there) but I do not see the real picture. or it does not appear when I create a PDF file of the file.

  Clues or suggestions are appreciated.

  Re: right now it's a TIFF with transparency.

  FM does not support transparency or opacity in raster images. It allows clipping paths, but you know the trick.

  Transparency, but no opacity, at least some vector formats (EPS) doesn't work, but only in the output path (not an extract) and only if the object is a vector.

  Basically, you need to make all this compositing layer in an external application and import the final result.

  Re: Conditional watermarks hidden behind graphics

  Re: Is it possible to vary the opacity of a graphics object created by Framemaker?

• Read and write the empty file - InputStream

  Hi all

  I have a problem with the playback of a file.

  This is my code:

  I create my file and put my datas:

  try {
          String filePath = "file:///store/home/user/locations.txt";
      FileConnection filecon =(FileConnection)Connector.open(filePath,Connector. READ_WRITE);
  
      // Always check whether the file or directory exists.
      // Create the file if it doesn't exist.
      if(!filecon.exists()) {
          filecon.create();
      }
  
      OutputStream out = filecon.openOutputStream();
  
      out.write(data.getBytes());
  
      filecon.close();
  
  } catch(IOException ioe) {
  
      Dialog.alert(ioe + "");
  
  }
  

  Then I want to read my data but my inputStream is empty and I don't understand why...

  String filePath = "file:///store/home/user/locations.txt";
  FileConnection filecon = (FileConnection)Connector.open(filePath,Connector. READ_WRITE);
  
  // Always check whether the file or directory exists.
  // Create the file if it doesn't exist.
  if(!filecon.exists()) {
      filecon.create();
  }
  
  InputStream in = filecon.openInputStream();
  InputStreamReader  reader = new InputStreamReader(in);
  
  StringBuffer sb = new StringBuffer();
  
  final char[] buf = new char[1024];
  int len;
  while ((len = reader.read(buf)) > 0) {
      sb.append(buf, 0, len);
  }
  
  data = sb.toString();
  

  Thanks for your help...

  Welcome to the forum.

  Can't see anything obviously wrong.

  I suggest for now you change to use the SD card instead of the store and run in the Simulator with the SD card simulated as a directory.  You can browse the Windows directory and if, in fact, the file is created as expected.

• How to retrieve and display the image on screen stored in pim...

  Hello world

  Can anyone tell how to recover the image store in pim and then display it on the screen

  See the code below. I just copied it from PIM API doc

   import java.io.IOException;
   import javax.microedition.pim.Contact;
   import javax.microedition.pim.ContactList;
   import javax.microedition.pim.PIM;
   import javax.microedition.pim.PIMException;
   import javax.microedition.pim.PIMItem;
   import net.rim.device.api.io.Base64InputStream;
   import net.rim.device.api.io.Base64OutputStream;
  
   public class PhotoExample
   {
  
       private Contact _contact;
  
       public PhotoExample() throws PIMException
       {
           ContactList contactList = (ContactList) PIM.getInstance().openPIMList(
                   PIM.CONTACT_LIST, PIM.READ_WRITE );
           _contact = contactList.createContact();
       }
  
       public void setPhoto() throws IOException
       {
           byte[] photo = getSamplePhoto();
           byte[] photoEncoded = Base64OutputStream.encode( photo, 0,
                   photo.length, false, false );
           if( _contact.countValues( Contact.PHOTO ) > 0 ) {
               _contact.setBinary( Contact.PHOTO, 0, PIMItem.ATTR_NONE,
                       photoEncoded, 0, photo.length );
           } else {
               _contact.addBinary( Contact.PHOTO, PIMItem.ATTR_NONE, photoEncoded,
                       0, photo.length );
           }
       }
  
       public byte[] getPhoto() throws IOException
       {
           if( _contact.countValues( Contact.PHOTO ) > 0 ) {
               byte[] photoEncoded = _contact.getBinary( Contact.PHOTO, 0 );
               return Base64InputStream.decode( photoEncoded, 0,
                       photoEncoded.length );
           } else {
               return null;
           }
       }
  
       private static byte[] getSamplePhoto()
       {
           // return the raw bytes of the photo to use
       }
  
       public static void main( String[] args ) throws Throwable
       {
           PhotoExample example = new PhotoExample();
           example.setPhoto();
           example.getPhoto();
       }
  
   }
  

  .