How to read the digital square wave pulses

Similar Questions

• How to read the digital I/o using PXI-7813R?

  Hi guys,.

  I'm reading a digital signal by using one of the ports in the PXI-7813R. The 7813R has 5 digital ports or 39 lines for playback of digital data. I have connected a SCB-68 as the physical hardware interface for 'plug-in' a 5V adapter, which will act as my signal at the moment.

  After you configure the PXI via MAX, I wrote two codes, one for my host pc and the other to control the FPGA through the host. But I think, I can have more complicated or completely gone in the wrong direction.

  Any help in the drafting of these codes would be well appreciaetd.

  Thank you, Anoop

  You need the FPGA to sample the signal how often you expect the device to send the data.

  If you write your data in the FPGA for the DMA, then on the side PC you just have to read the DMA.  I like to think of the DMA as a queue.  It makes it easier for me to understand how it works.

• How to read the file audio .wav on lumia 620

  I'm not able to play the audio .wav on lumia 620. I used an online converter and converted this track in mp3 format. But even in this case, there is no sound if I play this. pl advice.

  I'm not able to play the audio .wav on lumia 620. I used an online converter and converted this track in mp3 format. But even in this case, there is no sound if I play this. pl advice.

  Unfortunately, files .wav is not supported by the phone. You can convert the audio file to a different format by using an audio converter application so that it can be played on the mobile device.

• Digital square wave

  Hi all

  I want to check if my digital square wave turns on or off. If someone has an idea, please help me

  I created a mask, so that if my signal leave the mask. I have an Error Message. "It's job but every time I should change the values of the function Culsters ' specification limit" if I change the Signal

  You will find in the attachment the block diagram.

  Thanks in advance for your answers

  Best regards

  How are you brightness measure?  A digital signal is enabled or disabled.

  Duty cycle that you can measure quite simply.  There is a VI called Pulse Measurements.vi who will do it for you.

• How to remove the digital ID

  I have a digital ID in Adobe Reader X and forgot my password.  Because I don't believe that these passwords are recoverable, I need to delete the codes and start again.  But when I go to edit, then the protection window that opens is very light and I can draw anything to the top of this window. Can someone help me this this please?

  Hi GlendaKay,

  Please take a look at this thread: How to remove the digital ID in Acrobat 9 Pro Extended?

  Thank you

  Abhishek

• How to read the files on time capsule

  How to read the files on time capsule from iPad?

  Thank you

  Using an application like navigation on the iPad. More info here:

  Stratospherix - FileBrowser - overview

• How to read the status of User1 DIP-switch with a cRIO FPGA chassis?

  How to read the State of the DIP switches on a FPGA cRio chassis?

  I work with a cRIO 9022... My idea is to put the system in "service" mode with USER1 switch to IT and communicate with the FPGA via the FPGA - GUI (VI) on the host computer instead via the RT module that is used in normal conditions.

  Any ideas? Unfortunately, I don't have an unused channel on the left... .and (as I know) cannot use the interface RS232 of FPGA.

  Many thanks in advance,

  Luke

  Hi, this is the correct information. You cannot read the FPGA of DIP-switch status. The only thing you could do is to use the function of Reading Switch.vi located under the range of functions-> real-> utilities RT time

  It's how you probably know side host RT and not the FPGA.

  Cordially Virginia

• How to read the value of list boxes by iteration in a loop For?

  I have a lot of list boxes on the front of my VI. I want to know how to read the value of this combo with a loop boxes For. The point is that I don't know how to get the reference of each combo box in a loop.

  Any information would be welcome. Thank you!

  su27 wrote:

  I have a lot of combo boxes on the front of my VI [...]

  

  Be sure to close the references that you have finished with them.

• How to read the VI Analyzer config file?

  Hello

  How to read the analuzer vi configuration file? I'm getting a lot of errors on the size of the front panel and I don't know what should be the size you want. Where is the maximum expected size of the specified front panel?

  Kaspar says:

  Hello

  How to read the analuzer vi configuration file? I'm getting a lot of errors on the size of the front panel and I don't know what should be the size you want. Where is the maximum expected size of the specified front panel?

  If you have VI Analyzer installed, you can load the configuration file and look at the section select the Tests. There is a test for the maximum size of front under front-> User Interface. The default value is the resolution of the current monitor of the PC (including multiple monitors). You can change to the desired option.

• How to read the date and time of a file by labview information

  How to read the date and time of a file by labview information? for example, time created and updated time.

  The similar question had already spoken here (this is the old thread but still seems topical):

  http://forums.NI.com/T5/LabVIEW/file-date-created/TD-p/109836

• How to read the host name or serial number cRIO locally

  I have not worked with cRIO and decided to ask for help.  (o).

  I don't know about the screws that allow to access this information from a connected Windows machine, however, I want to retrieve and display this information on remote panels.  But I cannot determine how to read the cRIO hostname or the serial number of the software running on the cRIO?

  Thanks for the help.

  James

  This could help.

• How to read the two columns of data from the Port series

  Hello

  I'm reading two columns of data from the serial port.

  Example:

  52439 52430

  52440 52437

  52209 52214

  51065 51070

  52206 52390

  I use the serial of Visa service and I can read the first column of data from the serial port, but I can't understand how to read the second column.

  I want to both sets of chart data.

  I enclose my VI.

  Thank you for your help.

  The analysis of string function takes a "Format string" on top (with the right button of the function and choose Help, which explains all the entries).  In particular, you can say 'Give me two numbers separated by a tab' and the output will be two numbers (whole or floating, depending on the chosen format).  In particular, %d\t%d specifies a decimal integer, , whole decimal.

• How to read the color table in a subvi?

  How to read the color table in a subvi? Is it made by a reference to the table or with a global variable? For a better understanding of the problem, I added to vi. Run the "run.vi." I want to see

  the background color of the table "run.vi" in the subvi called "read color.vi".

  How can I do?

  Thanks in advance

  Norick

  pop up on the wire table refernece and establishes 'control '. Add this control to the icon of the sub - VI decision-making and then wire ref of the appellant to this Terminal VI so the calling VI move the ref to the Subvi.

  Ben

• How to read the 32-bit depth .bmp image

  How to read the image, 32-bit depth using LabVIEW .bmp?

  
  

• How to read the analog inputs of one Board of R for (PXI-7851R) series

  You can guide me please with the steps for reading of the analog inputs of a series a. card I use as the target fpga PXI-7851R.

  Have you looked at the examples provided with LabVIEW? There are examples showing how to read the analog inputs.