HOWTO connect to AP internal to the outside world?

Similar Questions

• Cisco ASA, connect an IP address on the OUTSIDE of the VPN remote access

  Hello

  I tried to find resources on the net but could not find a solution, then post it here. Maybe someone can help.

  So the problem is that I'm trying to access a server on the cloud for remote VPN access (cisco asa 5510).

  The server on the cloud (54.54.54.54) is only accessible from the outside interface (192.168.11.2) NY Firewall (cisco asa 5510)

  I added some ACE for this in the ACL of VPN tunnel to divide.

  NY-standard host allowed fw # access - list vpn_remote-customer 54.54.54.54

  And I see the road added to my cliet machine after the VPN connection, but still it cannot connect to this server.

  The network INTERIOR, I can connect to the server.

  

  Thanks in advance.

  Hello

  This is most likely a problem with NAT hair/U-turn hairpin.

  Will need to see the configurations or you would need to check yourself

  I don't know what your version of the Software ASA is to be like who determines what is the format of NAT configuration.

  So far, you have confirmed that the ASA VPN configuration provides the VPN Client with the route to the remote server. Then in circulation should be tunnel to the ASA.

  Then, you will need to check the output of this command

  See the race same-security-traffic

  You should see the command in the output below

  permit same-security-traffic intra-interface

  If you do not, you will need to add it. This effect of controls is to allow traffic to enter an interface and exit through the same interface. In your case this applies to Internet VPN Client traffic to the remote server as it between ' outside ' and spell through the 'outside'.

  Then, should ensure that dynamic PAT is configured for the VPN Clients.

  8.2 software (and below)

  You most likely have a dynamic configuration PAT like that on the firewall, if levels of above running software version

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0

  In this situation if we wanted to add dynamic PAT for a pool of VPN, we would add

  NAT (outside) 1

  This would allow users to use the same public IP address as LAN users, when accessing the remote VPN server

  Software 8.3 (and above)

  Because the NAT configuration format is completely different in the latest software, you could probably just add a new configuration of NAT completely without adding a

  network of the VPN-PAT object

  subnet

  dynamic NAT interface (outdoors, outdoor)

  Of course, its possible that there could be some configuration NAT already on the device which could cause problems for this configuration. If this does not work then that we would have to look at the actual configurations on the ASA.

  Hope this helps

  Let me know how it goes

  -Jouni

• Creating a virtual server connected to the outside world

  I currently have a server running on a fedora 12 VM Workstation VM. I want to access the server from outside of the virtual machine, but for a reason, even not the host computer will have access to the virtual server. Is it possible to route the network cards so that when someone outside the VM workstation tries to access the server VM, they can just go directly on the server instead of getting blocked by network adapters?

  Set up networks bridged and point it at your card of ethernet connected to the internet. If you have a router with NAT (like 99.9% of office configurations), you will need to forward individual ports if you want to be exposed to the public internet. If you are happy to expose it only within your local network, you don't have to redirect ports.

  Using network bridge, the virtual machine has its own IP address, whether on the public internet (in the case of no NAT) or on your local network (in the case of NAT). The scope of the IP address assigned is exactly her same as that assigned to the host computer - so if the host has an Internet IP, you need to configure one, or to have assigned via a DHCP server for your virtual machine as well. OTOH, if your host is behind a NAT, it probably has a DHCP server that puts an IP address in the range of 192.168.x.x for your virtual machine, automatically.

• 120W:how RV to block of connected device to intern in the name of the device?

  Hi guys,.

  I use the router, rv 120w

  can I block device connected to the internet through device name?

  for example, the phone Android wil always has "android" in their name of the unit. How can I block the device which has "android" in their device name of connection to the internet?

  Thank you.

  Hello

  Please use our forum

  Hi Louis, my name is Johnnatan and I'm part of the community of support to small businesses. Can´t you block any device by name, but you can block devices using mac address. Go firewall > access control > Mac filtering in this section, you can specify the mac address of devices and block them.

  I hope you find this answer useful,

  "* Please mark the issue as response or write it down so others can benefit from.

  Greetings,

  Johnnatan Rodriguez Miranda.

  Support of Cisco network engineer.

• Is it possible to connect to the APEX of the outside world?

  I have a requirement to connect to the application out APEX (a java program). Is there a way to do this, maybe a web service? The basic requirement is to display some data to DB APEX by a scheduled task.

  I had a way to publish the APEX application data. Found that it supported is for the RESTful web service. It worked for me.

• Endpoints VCS component the outside world

  Hi guys,.

  I can't find information about endpoints SIP calls from outside the organization.

  for example, I found a person, there a sip address - [email protected] / * / through which I can reach. I want to call him to registered VCS infrastructure endpoint. something about it is in this document (page 28), but there is no accurate confirmation on my suggestion.

  It is possible at all? and what I need to deploy that?

  Thank you!

  Create the rule of research according to the documentation - it's all you need to do. To confirm that it works correctly, you can test it with the closure of Cisco service which will loop your own video to you; call [email protected] / * /

  To dial [email protected] / * / you do not have to do anything at all, however, the people/organization you call must have the SRV records appropriate in place - even for you, if you want people to call you using the [email protected] / * /, then you must have in place appropriate SRV records.

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.

• Hide the domain name PIA for the outside world

  I have an architecture where I encouraged candidates on the external Internet to the intranet.
  The architecture is-
  
  Internet https> Apache http> Weblogic-> server-> DB applications
  
  I use the domain name on the link to access the site:
  
  http:// < site > .com/PSC/ < domain_name > / applicant, HRMS, c, HRS_HRAM. HRS_CE. GBL
  
  I don't want the domain name "< real domain_name >" to appear in the URL. How the mask/hide it?

  It is a request of my client and I was wondering if this is possible. Please advice.
  THX/t

• How can I connect to my webserver VM from the outside?

  I'm sure that there is an easy solution for this, but I searched without success.

  I run a Web server on FreeBSD in Fusion, and my Mac uses DHCP (static address can come in time).

  My VM (fusion 2.0.1) is connected through NAT, I also use my Mac as a local server for testing, but only to listen on 127.0.0.1

  Here's my question simply:

  My FreeBSD runs Apache and is set up to serve the site (example.com, say) and DNS settings are all up to date. (I know that the BSD Web server works fine because I can connect from Safari using the merger IP address directly).

  Now if from the outside (you, for example), type http://example.com/ in your browser, connect to my Mac via port 80 and Apache on my Mac will attempt to server web page. But what I really want, it's demand to go on the virtual machine without going through the Mac. (In analogies, there is a setting that allows some ports go 'on' the virtual machine, but merging doesn't seem to have it - I promise to change the merger, because it works best with FreeBSD).

  So in short:

  How to configure my machine Virtual Port 80, rather than the Mac doing listening to?

  MacGruder says:

  So in short: How do I set up my VM to Port 80, rather than the Mac doing listening to?

  I introduce it more as a proof of concept, then a full step by step guide because there are many variables and you did not really a complete topology of your local network and other relevant information to be explicit and accurate on a total scope of the project.

  Good on my MBP without Apache running in OS X and a Virtual Machine of defined merger on NAT with Apache running on the client, I modified the nat.conf and reset the VMware network and was able to directly access Web Server of the customer from another physical Machine on my local network.

  OS X host IP address: 192.168.1.100

  Merge comments NAT IP address: 172.16.172.128

  Another physical Machine on the LAN IP address: 192.168.1.3

  Named Fusion comments: webtest

  Installed the Apache server in comments and editing the web page by default so you can be sure I look what I expect to be looking at and not the host content of the Apache server.

  Stop and closed Fusion comments

  Edited "/ Library/Application Support/VMware Fusion/vmnet8/nat.conf" and added 80 = 172.16.172.128:80

  Restarted network VMware with: sudo "/ Library/Application Support/VMware Fusion/boot.sh"-restart

  Open fusion and began comments

  Editing another physical Machine on the LAN hosts file to add: 192.168.1.100 webtest webtest.com www.webtest.com

  Browser open on another physical Machine on LAN and typed http://www.webtest.com

  Now, I'm looking at the modified Apache file index.html.en default server prompt so it allows me to know that I can access a Web server on the Guest NATed through the Port 80 of the host of another system other then the host.

  Notes:

  Personal firewall should of course be properly defined to allow connectivity between the systems.

  If you what the outside world can then access if your host doesn't have a static IP address, then you will need to use a form any Dynamic DNS on the host computer.

  It is in any case just to let you know it is possible and it's just one of the ways of May to go on this subject and without all the relevant information, I don't have the time to enter in other scenarios.

  Hope that helps!

  Post edited by: WoodyZ

  Added the second - to - restart

• Unable to connect to the outside through Horizon View Client

  http://www.VMware.com/files/PDF/view/VMware-view-evaluators-Guide.PDF

  I'm in the middle of evaluation of VMware Horizon View Suite. I set it up according to the information provided in the link above

  I am able to connect to my desktop PC internally through the Horizon View Client and HTML.

  I am also able to connect to the outside through HTML - BUT NOT - through the Horizon View Client from an external location.

  My first thought is that I have all the correct ports open on my firewall to network, that's what I opened, did I miss something?

  TCP / 80

  TCP / 443

  TCP / 4001

  TCP / 4172

  TCP / 8009

  TCP / 8443

  UDP / 4172

  Any help is appreciated with this!

  Exercise 3: connection to a Horizon of a customer of Mobile display view desktop

  "Launch the Horizon View Client you iOS mobile device...". "You will be asked to enter the host name or IP address of the view composer Server"

  See Server of composer? When I enter this IP address, it does not work immediately, it's a typo?

  Any help is greatly appreciated

  http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC&docType=kc&docTypeID=DT_KB_1_1&externalID=1036208

  My problem was solved by following the information provided in the above document (video), but the following two documents where it is also very useful

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=1028332

  0 224598712 http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC&docType=kc&externalId=1039021&sliceId=2&docTypeID=DT_KB_1_1&dialogID=224578928&StateID=0

• How to hide my wireless connection personal House of the user of the computer on the outside

  I see from time to time by my window a vehicle that is parked outside using their computer. Someone told me that they can connect to the internet using my wireless signal. How can I hide the outside user I have a wireless connection?

  Hello Maria,.

  There are a few things you can do to make sure that you are safe.

  #1. Make sure that your wireless modem is protected using a personal code to access WEP or WPA2. This is done by going to the configuration of your modem and the establishment under the wireless tab / link / article. Of the modem user manual must be able to guide them in this process.

  #2. The other way is to disable the broadcasting network option in the modem. The only problem with this option, it is only people who are currently using the network can get on again.

  I recommend establishing a password on your wireless network and in this way people can see your broadcast network, but they will not be able to get on it, unless they have the password.

  Hope this helps,

  JB

• ESA 8.3 - spoofed email (internal domain of outside)

  Hello

  is there a fast and reliable way to block e-mail messages from a sender with an internal address through the incoming stream?

  Currently, it seems that the mail is marked as being junk (probably) is not a good thing. All mails with the internal domain from outside as the sender may be rejected at the level of the connection.

  How do to get there, with a filter of strategy or is there already a built-in mechanism?

  -Michael

  Simple policy filters do not require license compliance.

  Respect is only when you use things like dictionaries and the features you see in the area of compliance.

• Remote access VPN client to connect but cannot ping inside the host, after that split tunnel is activated (config-joint)

  Hello

  I don't know what could be held, vpn users can ping to the outside and inside of the Cisco ASA interface but can not connect to servers or servers within the LAN ping.

  is hell config please kindly and I would like to know what might happen.

  hostname horse

  domain evergreen.com

  activate 2KFQnbNIdI.2KYOU encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  ins-guard

  !

  interface GigabitEthernet0/0

  LAN description

  nameif inside

  security-level 100

  192.168.200.1 IP address 255.255.255.0

  !

  interface GigabitEthernet0/1

  Description CONNECTION_TO_FREEMAN

  nameif outside

  security-level 0

  IP 196.1.1.1 255.255.255.248

  !

  interface GigabitEthernet0/2

  Description CONNECTION_TO_TIGHTMAN

  nameif backup

  security-level 0

  IP 197.1.1.1 255.255.255.248

  !

  interface GigabitEthernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Management0/0

  Shutdown

  No nameif

  no level of security

  no ip address

  management only

  !

  boot system Disk0: / asa844-1 - k8.bin

  boot system Disk0: / asa707 - k8.bin

  passive FTP mode

  clock timezone WAT 1

  DNS server-group DefaultDNS

  domain green.com

  network of the NETWORK_OBJ_192.168.2.0_25 object

  Subnet 192.168.2.0 255.255.255.128

  network of the NETWORK_OBJ_192.168.202.0_24 object

  192.168.202.0 subnet 255.255.255.0

  network obj_any object

  subnet 0.0.0.0 0.0.0.0

  the DM_INLINE_NETWORK_1 object-group network

  object-network 192.168.200.0 255.255.255.0

  object-network 192.168.202.0 255.255.255.0

  the DM_INLINE_NETWORK_2 object-group network

  object-network 192.168.200.0 255.255.255.0

  object-network 192.168.202.0 255.255.255.0

  access-list extended INSIDE_OUT allow ip 192.168.202.0 255.255.255.0 any

  access-list extended INSIDE_OUT allow ip 192.168.200.0 255.255.255.0 any

  Access extensive list permits all ip a OUTSIDE_IN

  gbnlvpntunnel_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0

  standard access list gbnlvpntunnel_splitTunnelAcl allow 192.168.202.0 255.255.255.0

  gbnlvpntunnell_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0

  standard access list gbnlvpntunnell_splitTunnelAcl allow 192.168.202.0 255.255.255.0

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  backup of MTU 1500

  mask of local pool VPNPOOL 192.168.2.0 - 192.168.2.100 IP 255.255.255.0

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm-645 - 206.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT (inside, outside) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

  NAT (inside, backup) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

  NAT (inside, outside) static source DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

  NAT (inside, backup) static source DM_INLINE_NETWORK_2 DM_INLINE_NETWORK_2 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

  !

  network obj_any object

  dynamic NAT interface (inside, backup)

  Access-group interface inside INSIDE_OUT

  Access-group OUTSIDE_IN in interface outside

  Route outside 0.0.0.0 0.0.0.0 196.1.1.2 1 track 10

  Route outside 0.0.0.0 0.0.0.0 197.1.1.2 254

  Timeout xlate 03:00

  Pat-xlate timeout 0:00:30

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  identity of the user by default-domain LOCAL

  Enable http server

  http 192.168.200.0 255.255.255.0 inside

  http 192.168.202.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  monitor SLA 100

  type echo protocol ipIcmpEcho 212.58.244.71 interface outside

  Timeout 3000

  frequency 5

  monitor als 100 calendar life never start-time now

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  backup_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  backup of crypto backup_map interface card

  Crypto ikev1 allow outside

  Crypto ikev1 enable backup

  IKEv1 crypto policy 10

  authentication crack

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 20

  authentication rsa - sig

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 30

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 40

  authentication crack

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 50

  authentication rsa - sig

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  authentication crack

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 80

  authentication rsa - sig

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 100

  authentication crack

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 110

  authentication rsa - sig

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 120

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 130

  authentication crack

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 140

  authentication rsa - sig

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 150

  preshared authentication

  the Encryption

  sha hash

  Group 2

  life 86400

  !

  track 10 rtr 100 accessibility

  Telnet 192.168.200.0 255.255.255.0 inside

  Telnet 192.168.202.0 255.255.255.0 inside

  Telnet timeout 5

  SSH 192.168.202.0 255.255.255.0 inside

  SSH 192.168.200.0 255.255.255.0 inside

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH timeout 15

  SSH group dh-Group1-sha1 key exchange

  Console timeout 0

  management-access inside

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal group vpntunnel strategy

  Group vpntunnel policy attributes

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list vpntunnel_splitTunnelAcl

  field default value green.com

  internal vpntunnell group policy

  attributes of the strategy of group vpntunnell

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list gbnlvpntunnell_splitTunnelAcl

  field default value green.com

  Green user name encrypted BoEFKkDtbnX5Uy1Q privilege 15 password

  attributes of user name THE

  VPN-group-policy gbnlvpn

  tunnel-group vpntunnel type remote access

  tunnel-group vpntunnel General attributes

  address VPNPOOL pool

  strategy-group-by default vpntunnel

  tunnel-group vpntunnel ipsec-attributes

  IKEv1 pre-shared-key *.

  type tunnel-group vpntunnell remote access

  tunnel-group vpntunnell General-attributes

  address VPNPOOL2 pool

  Group Policy - by default-vpntunnell

  vpntunnell group of tunnel ipsec-attributes

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns migrated_dns_map_1

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the migrated_dns_map_1 dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory

  monthly periodicals to subscribe to alert-group configuration

  daily periodic subscribe to alert-group telemetry

  Cryptochecksum:7c1b1373bf2e2c56289b51b8dccaa565

  Hello

  1 - Please run these commands:

  "crypto isakmp nat-traversal 30.

  "crypto than dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 Road opposite value.

  The main issue here is that you have two roads floating and outside it has a better than backup metric, that's why I added the command 'reverse-road '.

  Please let me know.

  Thank you.

• Cannot "connect as current user" via the Security Server

  Hello community,

  I had a problem using the "connect as current user" option against a network outside of the enterprise security server. Connection by manually keying in the name of user and password works very well from the outside the company network For internal connections using a connection to the server instead of security server, everything works as expected without having to manually type the name of user and password.

  Single domain

  Customer of the horizon is 3.5.2 and joined to a domain

  2 Security Server 6.2.1 x

  2 Server 6.2.1 connection x

  On one of the servers of connection I got the following error message when you try to connect through the horizon customer using the option "connection as the current user:

  2015 12-28 T 20: 21:15.207 + 01:00 INFO (B 0, 08 - 0E34) < ajp-nio-8009-exec-7 > [PAEContext] (SESSION: a774_ * _b2fb) Idle Timer executor by using 1 thread (s)

  2015 12-28 T 20: 21:15.625 + 01:00 ERROR (0744-0AEC) < MessageFrameWorkDispatch > [ws_winauth] [GSSApiProcessServerContext]: negotiate failed. Error 0 x 0000000080090300 (not enough memory is available to complete this form) {SESSION: a774_ * _b2fb}

  2015 12-28 T 20: 21:15.626 + 01:00 (B 0, 08-04 B 8) WARN < ajp-nio-8009-exec-8 > [GssapiHandler] (SESSION: a774_ * _b2fb) failed connection GSSAPI: not enough memory is available to complete this application

  2015 12-28 T 20: 21:15.627 + 01:00 ERROR (B 0, 08-04 B 8) < ajp-nio-8009-exec-8 > [GssapiHandler] (SESSION: a774_ * _b2fb) cannot close the context 7 36 d-*-00D 3 with the error: unable to locate the context requested

  2015 12-28 T 20: 21:15.627 + 01:00 ERROR (B 0, 08-04 B 8) < ajp-nio-8009-exec-8 > [GssapiAuthFilter] (SESSION: a774_ * _b2fb) authenticate GSSAPI performance problem - GSSAPI_ERROR: GSSAPI failed: not enough memory is available to complete this application

  The connection to the server has 12 GB of memory in total and 9.5 GB of memory free/available.

  In the windows event log, the following error message appears:

  BROKER_USER_AUTHFAILED_GENERAL

  Failed to authenticate the user < UNAUTHENTICATED >

  Attributes:

  Node = hostnameofconnectionsserver.mydomain.com

  Gravity = AUDIT_FAIL

  Time = Mon 28 Dec 19:51:16 THIS 2015

  Module = broker

  UserDisplayName = < UNAUTHENTICATED >

  Source = com. VMware.VDI.Broker.filters.GssapiAuthFilter

  Recognized = true

  Just tried from a machine arrived in the area via the Security server. Cannot open a session as the current user. We also enabled on the external connections of MFA, but I don't think that should make a difference.

• Message to the outside, mail

  So I was on vacation for a week, come back today and learned that my message on the outside has absolutely nothing. I've got people who think that I just ignored the days now. I'm not happy.

  This IMAP account is on two computers, my job and my home. I've implemented the rule to the work and tested very well (not enforce), shut down the computer.

  At home, I don't think even to test the account again once and shut down the computer before leaving.

  I have to set up the answer further on EACH computer on which the IMAP account connected to it? or only for the last device that will receive mail? (Sense judgment of the work computer, go home, install the rule here, then stop that comp)

  Finally and this better not be true, but OSX Mail needs to be running for the rule to be active?

  If you configure the rule in your mail client, the client must be run to have the rule to work. Instead of putting in place such a rule is on the mail server. This by accessing the page from the server web mail.

• Add WRT54G: second router / access point, unable to get to the outside network.

  Here is the prob:

  We just got cable internet the other day and the cable operator insisted on using their v1000 Belkin F5D7234-4 instead of my WRT54G V8. So I thought I'd use the WRT54G as a second router/AP (without wireless/LAN/WAN). I was eager to do this by running an ethernet in the WAN on the WRT54G port and plug it into the port of the client on the Belkin, place the wrt - 54 G at the other end of the House and have the WRT54G broadcasting the same SSID and require authentication even as the Belkin and use the Belkin to Linksys Wireless Bridge. In this way, it will extend my wireless network and all computers can access the internet and the other (wireline customers will keep at wire-speed, wireless is not authicate to two different networks.)

  I can't get the Linksys network based able to see all the other computers outside the WRT - 54 G, even for wireless clients. On the side of things Belkin network, I can't ping the router even if she pulls a DHCP in the Belkin address. All customers the Belkin side can meet and thin internet. I've fiddled with the WRT54-g for almost an entire weekend now with no result. The WRT54G can see the other router as a DNS as well as external DNS providers, but none of the client computers can. Basically, I'm wanting to extend the network of Belkin 4 as most cable customers and fill a few dead wireless, and make the visible computer on the same network of suggestions?

  Parameters of WRT - 54G:

  Automatic configuration - DHCP

  Same domain name like Belkin
  IP router set a tire to the DHCP server

  DHCPserver OFF

  Mode of operation: router

  Safe are disabled.

  Wireless SSID is the same as Belkin

  Wireless channel is the same as belkin.

  Method and auth. key is the same as belkin.

  Belkin:

  DHCP is on.

  15 IP addresses available.

  Wireless gateway is on with the WRT54G Wireless MAC address information.

  Ethernet cords are connected.

  I played with static routes for hours, tried the option routing dynamic, even tried DMZing of the WRT54G intellectual property in the belkin and still unable to connect to the internet. Tried the Belkin MAC address cloning. Nothing seems to work. When I plug the WRT - 54G directly in my digital/Modem/phone cable box, I get internet and everything. I'm at the point of throwing same DD - WRT on it.

  But beyond connection "wireless" I discovered really does not work if well (drops random wireless speeds seize up) with two different pieces of equipment running two different firmwares. So the thing connecting wireless set was out the window.

  I however knew what I had to do Linksys firmware:

  1.) DHCP clients forward.

  Customers of Belkin - network

  Linksys customers - network B

  The dhcp pool was not get transferred to the client computers. That is the 1-2 on network computer had XXX. XXX.100 - 102 for 3-4 computers on network B was YYY. YYY. YYY statically set by Windows. Even after changing to a static address on the network A dhcp scope I could still connect to the internet or to one of the computers on the network.

  The static routing table seemed not lead me anywhere either, and I've tried dozens of configurations.

  The way I got it Setup is with the customer enthernet of the Belkin ROUTER to THE Internet on the Linksys WRT54G port 1-4. Maybe I should have plugged the ethernet on the client side of 4 ports Linksys?

  Anyway DD - WRT redirect DCHP feature was what I need.

  Regarding the scenario wireless two routers have the same encryption method and key but different channels and ssid. Who, with DD - WRT for some reason when I jump on the wireless-B, Vista will be ID it as network A (B).

  I hope that it has not violated anything except the guarantee which was anyway. The reason for which I needed for my network up this way is because I do a lot of work using VM (of various operating systems), is simply easier to have two separate semi networks. (to different physical locations in the House)