HOWTO ssh or telnet to the Simulator

Similar Questions

• How the router can understand protocols such as SSH or telnet

  How the router can understand protocols such as SSH or telnet
  and device for layer 3 router

  second question, I found this accessory of CCNA security book Keith Barker
  wrote it router look at application layer information how?

  Thank you in advance.

  Hello

  I think that confuse you routing process.

  Router; route packages using their layer 3 address.

  This means not router cannot understand the upper layer protocols. There just transmission by addressess of layer 3.

  for example: we can define Access-list for tcp and udp layer 4 packets. router can decide whether to permit or refuse even if these lists filter by glance in the section layer 4 of the package.

  In an SSH or Telnet session, role of the router is terminal.

  Intermediate device belongs in the the router routing process.

  Best regards.

• SSH and Telnet access for catalyst 4503 list

  I was wondering the structure of command to apply an access list to ssh and telnet on a catalyst 4503. I keep a list of access for indoors and outdoors. Can afford two different IPs from the outside? Thank you

  You will need create an access list indicating the networks/hosts that you want to allow.

  -Example

  access-list 10 permit 10.10.1.10

  access-list 10 permit 10.10.2.10

  access-list 10 permit 127.1.0.0 0.0.255.255

  access-list 10 permit 192.168.1.0 0.0.0.255

  So you want to put this list of access on the VTY interfaces.

  -Example

  line vty 0 4

  access-class 10

  entry ssh transport * if you only want to SSH *.

  line vty 5 15

  access-class 10

  entry ssh transport * Ditto *.

  Now you can do all this with * line vty 0 15 * but, it gives you a better idea of what is happening. It is a simplistic configuration. Remember that it is advisable not to allow ssh. If you want to allow at the same time, let him * transport input ssh * out of the configuration.

  I hope that gives you an idea of the structure. If this is not the case, let me know.

• App-Manager does not connect to the Simulator OS Firefox on Windows 7

  OS: Windows 7

  Firefox: 28

  6.0pre8.20140112 Simulator 1.2 Firefox OS

  When I run the simulator it opens fine and I see a Firefox OS Desktop
  But the App Manager does not connect. The console at the bottom right says:

  .. localhost:56455 options (the port varies)

  .. connection timeout. Possible causes: has not clicked 'accept' (guest).

  .. .disconnecting

  .. .disconnected

  I have disabled my firewall, restarted firefox and even system - did not help
  There is a similar bug - but I don't know if we are talking about the same thing:
  https://support.Mozilla.org/en-us/questions/988385

  Thank you

  Well - I already knew these links and I can't find anything useful
  Anyway, I tried the Simulator instead of 1.2 1.3 (unstable)
  This one works very well

• Default device in the Simulator

  Hi guys

  Is it possible to set the default device Simulator? I always want to turn into one of those more peripheral NOT. All except 6 + and 6 s +.
  It is annoying when it does not fit in my MBP 15 ".

  Thank you

  You can try to reset the Simulator, but I think it's just the default value for the last type of device used.

• Control the simulation time to align the time system

  Good so maybe it's blindingly obvious or just simply a ridiculous question but here goes:

  I run a dll that I produced from a .mdl file. My goal (among others!) is to get the dynamic response of the exact model of 'real world' calendar (date system). The tuning for the appearance of the control of this model is based on the duration of simulation with produced in simulink and so it is desirable for me to define the duration of the simulation to run when the system.

  The problem I have, if you open the workspace and produce a template control, the simulation shown time is much faster than the time system.

  For example, one iteration of the model takes a fraction of a second. What I imagine happens, it is immediately restart (and progress of a time step). I guess I want the model to wait until it is in harmony with the system time before iterate again.

  Is there a way to solve this problem, and do anyone know if this problem will be resolved in Simulink or Veristand 2009.

  Any information would be appeciated, my trawl of the help files OR have not really answered the questions yet good

  Thank you
  James

  The models are running in sync with the rest of the system. Unless you specify a decimation factor for your different model of 1 for each tick of the primary control loop your model put once, too. The difference between the model and system duration that you see is due to the fact that the model time is based on its time not Delta T compiled, not any of the wall clock time. Every time that the model is Ticktock, it adds its own Delta T to its operation time string.

  The time channel system is based on the Delta T of the primary control loop. Thus, it corresponds with the rate you specified the system to run at. If these Delta Ts are the same, are aligned at the same time. If you want the time to model to match an actual wall clock time, you can adjust the flow of the loop of the primary control loop to match the Delta T, or adjust the factor of the decimation of the model so that it gets only checked once for every N the primary control loop iterations.

• How to set the simulated on material values simulated?

  I simulate the material using the Software NI MAX.
  I would like to access the material simulated using the interface in ANSI C.
  But I want to get the values.

  How it is possible to adjust the simulated values?

  You can not. The only value of simulation is the wave sinusoidal, as explained in the help.

• The simulated signal RMS

  
  

  Dear Susan!

  I took a glance on your application.

  It's really good, but the calculation of the effective measures should not be implemented in the Simulation of control loop, since the calculation will be dune for each point this may require Ness on the graphical indicator, when you run the code.

  I made a few changes and used Uilities int Simulation palette palette function of collector . This function allows to collect data and do the treatment on it, the end of the simulation.

  Please find attached code.

  If you have any questions, feel free to ask.

  BR,

• Multisim 12 - by clicking on the button "stop the simulation", does not seem to turn off the circuit

  Greetings.

  I recently installed 12 Multisim and have not changed the basic operational parameters, I know...

  Shortly after installation, the application is an update.

  Your help is apprecaited to understand what is happening...

  Steps to recreate:

  1. start multisim.

  2. open a very basic circuit that includes a battery 10V with the ground, a lamp, a voltmeter between the lamp and an ammeter in series.

  3. use 'switch' at the top right of the appliation multisim window to run the simulation.

  4 lamp shows a 'enlightenment' and voltmeter indicates 10V and ammeter indicates .1a circuit.

  5. use the switch to stop the simulation.

  6. no change in the circuit or lighting of the lamp measures.

  7. same results if the simulation starts the arrow and the red square are used to start and stop.

  If I close it and reopen it circuit, the circuit begins in the OFF state, but will not OFF If when you select stop simulation.

  This is the case with several circuits, those provided by the College and the other that I created based on the same design.

  Multisim restarting has no effect to correct this observation.

  It doesn't seem normal that when the simulation running, values or apparent lamp lighting does not change.  The simulation doesn't have to go back to the start state (OFF) when I stop the simulation?

  I captured the homerun status after stopping the simulation.

  Thanks in advance for your help.

  Zan

  Hi zanzarista,

  Multisim retains the values for everything in the circuit when the simulation is stopped. Which means that you are able to view the values on your instruments (such as multimeters) even after the termination of the simulation. When you start a simulation once again, starts all over again and that's why you see a 0 momentarily.

  It is the way in which the software is intended to work.

  I hope this works.

• I have a problem with the simulation in Matlab 6.5 and LabVIEW for PID controllers

  I have a problem with the simulation in Matlab 6.5 and LabVIEW. I have a few methods for granting regulators PID in MATLAB to go but not of LabVIEW. Degree of international teams of two transfer but when I passed to the fourth degree is no longer working. We have changed the formula to calculate the parameters for the fourth year and gave me some good values for assignment of Matlab, but when I put on LabVIEW are not resolved. the formulas are available in PDF format and are. Please help me and me someone if possible. Thank you
  Lim.4 generation in comparison methods and the MATLAB program settings are for the service of transfer to the second degree.

  Hello Lascarica,

  I noticed that you are using the screw of PID. Gains on these screws are based on TIME instead of GAIN. You should be able to build a PID regulator and vary the gains and then compare the results.

• Windows 7 - is possible to run telnet via the LINE of COMMAND BACK?

  I activated the Control Panel - programs - telnet client activate Windows features turn on or off - and a check by the Telnet client.

  I CAN run telnet from the Start button and typing telent.   Telnet.exe is located and I click on it, and a telnet window opens.   The title bar of the window is "C:\Windows\system32.telnet.exe".

  I can't run telnet from the command line, even as an administrator.

  C:\Windows\System32>Telnet
  'telnet' is not recognized as an internal or external command
  operable program or batch file.

  C:\Windows\System32>.\telnet
  '. \telnet' is not recognized as an internal or external, order
  operable program or batch file.

  C:\Windows\System32>.\telnet.exe
  «.\telnet.exe' is not recognized as an internal or external command
  operable program or batch file.

  I want to be able to enter telent 192.168.1.1 at the command prompt, is it possible on Windows 7 without having to install a client telnet replacement?

  I am running Windows 7 Enterprise 64-bit with Service Pack 1.    My computer is in the domain of the company.

  back / cmd - a rose by any other name...   You know what I mean.

  But I found the link interesting it specifically shows run telnet from the CMD prompt.   I am not able to do, the mistakes, I have indicated in my original post.

  So, I clicked on "Start", "Run" and type cmd and press ENTER.  I then typed in telnet you press on enter, and wow, this has worked.  So, what is the difference?

  I looked at the properties of the shortcut, I always click to open a command window.  I see that it does the following:

  C:\Windows\SysWOW64\cmd.exe

  I even clicked on start, run and then type the full path and the name "C:\Windows\SysWOW64\cmd.exe".

  I typed in telnet again and it failed!  Hmmm so my computer run when I enter cmd versus C:\Windows\SysWOW64\cmd.exe?  and why is there a difference anyway?

  I find these two files and I perform a checksum on each of them, the files are the same:

  ad7b9c14083b52bc532fba5948342b98 *c:\Windows\System32\cmd.exe
  ad7b9c14083b52bc532fba5948342b98 *c:\Windows\SysWOW64\cmd.exe

  In fact, I suspect that they are in fact only one file with a hard to another link.  (Okay beat me on that too because I know MS does not use Unix terminology)

  So, now that I have created a new shortcut pointing to c:\Windows\System32\cmd.exe and receive launch Telnet works!

  It seems that when I run SysWOW64 cmd.exe, it does not. \System32 on its passage.  I tried to run c:\Windows\System32\telnet.exe - he started, but he doesn't answer.  I assumed telnet.exe is not compatible with Windows 7 64-bit.   And that's what I think, it's the current response.

• Cannot install the Simulator in Windows 10

  Try to install the Simulator on 10 (64-bit) Windows, get the error:

  "Windows error 2 occurred during the loading of the Java virtual machine"

  I installed the latest Java from java.com (1.8.0_73)

  Any ideas?

  Found a solution on stackoverflow

  You need to run the installer through the command line with the following options:

  blackberry10simulator - install .exe LAX_VM -i GUI

  that is, to define the full path to the runtime java.exe
  The '-j' have GUI "parameter was also necessary

  BlackBerry ceased to test such things?

• How to landscape on the Simulator?

  I can't understand how the Simulator go from portrait to landscape (guess BB have that option, honesty allows me to say that I do not have a BB device). I set myself for orientation in the controller application of "up to", which actually turn to the landscape position, but nothing changes on the virtual screen, not to mention the resolution switching.

  I use the version of Simulator 10.2.1.1925 on VMware Workstation 10 BB10. What I'm testing, is just the web browser. The site I'm doing works very well in the landscape on iOS and Android, so I'm sure that's not what is the cause of not working. But I still want to test my website on BB in landscape

  Anyone know how?

  Either works for me including just by clicking at the bottom right, as stated in the documentation, but what works for you.

  http://developer.BlackBerry.com/DevZone/develop/Simulator/simulator_gestures.html

• Cannot debug/run app in the Simulator from IDE update

  I did the error has earlier to upgrade my momentics IDE to 2.1, and since I'm unable to successfully launch my app to the market or debugging in a simulator. The application loaded on the Simulator and I can run from the home screen by pressing on it, but while the splash screen is displayed, the application stops immediately when launched from the IDE. There is no error message displayed in the console, the application stops just immediately after the splash screen is displayed.

  I tried with five simulators which worked very well all the way from 1.0.x to 10.3.x. I am lucky to have an old copy of the 10.1.0 IDE still on my system and I can run and debug my app very well using this one, but I would really be able to use the IDE to 2.1 again. It worked fine on the 2.0 IDE too, these problems just started to happen after the 2.1 IDE update.

  Has anyone else seen this, and if so, have you found a solution?

  OK, never mind. I accidentally upgraded my old working version of the IDE too all by improving the SDK (I forgot that it updates too the IDE) and panicked because then it would be not too run or debug from the IDE. I solved it but by uninstalling the TWO versions of the IDE, then put it back up from scratch. After the clean install, everything is fine and I can run and debug fine with 2.1 IDE.

  I guess it's something messed up with the upgrade process. A fixed.

• Can't see image Simulator in the Simulator window

  I have the eclipse plugin and when I run an app in the Simulator, simulator window appears and it is empty.  I use the Edit-> copy instant camera and then 'paste' in the painting and the image of the phone rises.  I looked around and I can't find another post with this problem, so any help would be appreciated.

  Thank you

  Found my question - the simulator window was open on my secondary monitor.  When moved to the main screen images appeared very well.

  Thank you