HP 14 laptop: Message: boot image selected didn't authentica you. Press on < enter > to continue

Similar Questions

• Selected boot image is not authenticated. Press on < enter > to continue

  I just removed the stock HARD disc that came with my M4-1015 x and now I am trying to install windows 7 on the SSD that I replaced it with. However, when you start up I get the message "the selected boot image is not authenticated to. "Press on < enter > to continue" when the laptop tries to read the operating system from the disk. I've never seen this before... any help? (This is a legitimate copy of Windows 7 DVD)

  Thank you.

  I fixed it. Of the secureboot to activate and deactivate bootmode inherited so he can work.

• HP Pavilion 15 laptop: boot image selected is not authenticated

  When you turn on the laptop says «boot image selected not to is not authenticated...» "What do I do?

  It's your computer laptop one with a removable battery?

  Remove the battery, unplug the power adapter and press and hold the power button for about 15 seconds. That will reset the hardware of the laptop.

  Put the battery back in and press the power button.

  Post your results here if you please.

• "HP Pavilion X 360 13": HP Pavilion X 360 13 ' selected boot Image is not authenticated. Press on &lt; enter &gt; to continue

  Hi all! I was wondering if someone could help me. My laptop started to tell the boot image selected is not authenticated is and asks me to press on enter. However, whenever I do this, the laptop is just turns off. I have read through the forums and tried all unique methos. No matter what I do, I can't access and type of BIOS or diagnostic, everything I chose makes it go to this screen. If you could give me any help, I'll be very grateful. It comes preinstalled with Windows 8 and has since then been upgrade Windows 10.  Also, when I turn on the computer, I heard a strange buzzing of the mouse pad area, what is?

  Thank you!

  Spoiler (Highlight to read)

  Spoiler (Highlight to read)

  Oops, I didn't add this.

  Oops, I didn't add this.

  Hey there! @mycatdaphne, thanks for the reply.

  Thank you to perform troubleshooting.

  As you mentioned that you still can not access BIOS.

  It's a hardware issue please contact HP support for service options.

  Link to contact HP: http://hp.care/2bkTGBQ

  Have a great day!

• HP 250 g4: boot image selected is not authenticated

  Hello, my computer has problems from the beginning. One day, I restart my pc and this appears:
  "Boot device not found.
  Please install an operating system on your hard drive
  Hard drive (3F0)
  The F2 System Diagnostics.
  So I did all the tests diagnostic tests and all translate "SUCCESS."
  I called support and they are sending me the two DVD «Recovery media for windows 10 products»
  I followed the instructions and put the first DVD, and then I started the pc. At first, it seems that the cd will then start appears this sentence "the boot image selected is not authenticated to. Press to continue.
  What could I do?

  Hello

  Try the following.

  Judgment of the laptop.

  Click next to the ESC key as soon as you press the power button to enter the Boot Menu, and then select the Bios Menu ( f10 ).

  Under the System Configuration tab, expand the Boot Options Menu.

  Select 'Clear all secure startup keys' and click Ok

  Select "load factory defaults keys HP", and then select Ok

  Save the changes that you exit the bios and try to re-run the recovery DVDs.

  If you still receive the error, return to the Bios Menu, System Configuration tab and expand the Boot Options Menu.

  Activate 'Legact Support' and save the changes that you exit bios - you will then need to enter a PIN of 4 numbers displayed on the screen to confirm the changes to the settings - enter the code and press ENTER.

  Try to run the recovery dvd.

  Kind regards

  DP - K

• n005tx Pavilion 15: "selected image is not authenticated to. "Press on enter continue" at the start of the

  Hi all, I have a pavilion laptop g6 - 2253ca who works with a windows 8 (64-bit). I have a strange problem since this morning and an error msg "selected image is not authenticated to. "press on enter continue ' that appears when I try to start. I have not installed program on my computer before it happens. I just sailed on the Internet and all of a sudden the screen is grey and the msg appeared on this subject.

  I went on several forums for information on this subject. That's what I did:

  -hard reset
  -Restart and boot into BIOS
  -Disable secureboot and enable legacy initialization
  -Press F10 to save and exit BIOS

  -Restart

  -the system asked me to enter a digit of 4 password and press ENTER to apply the changes

  -done, but I got stuck another MSG: "no boot device, insert the boot disk and press any key.

  Not able to find something else to move to another service I thought that maybe the value default bootable device was not the HARD disk if:
  -I restart and boot into the boot F9 Manager
  -does not not the same msg (no boot device, insert the startup disk and press a key) is displayed.

  Try to run the auto repair using the F11 Recovery Manager, but I can't start on it during startup.

  So, what should I do now? I am really disappointed...

  Hello

  Try loading at F2 run check disk test hard if that passes you will need a recovery disk. If the hard drive is not detected reinsert the disc hard try to rerun the test if you have the same hard disk problem that went wrong to replace the drive. Please call HP technical support check for warranty and the part replaced.

• Selected pass contains a string indicator combo box when you press the Enter key

  Hello

  How to pass selected contains a string indicator combo box when you press the enter keyboard key?

  Right now I use a button to send the command selected in the combox to string indicator.

  The photos shows a combo box with the button that I use to send to the indicator as example.

  After the user selects the text to pass, "send the cmd" button must be pressed to pass the string.

  I need to pass the selected string when the user press enter on the keyboard rather than press the button 'send cmd '.

  Kindly to you needing help.

  Hello

  You can use a structure of the event to capture keystrokes and filter, transmit only the drop-down list box "value of the indicator of channel when you press the return or enter key."

  Let me know it the joint allows an example (in LV 8.6).

• HP ENVY m6: boot image selected is not authenticated

  I need advice. "" When I turn on my laptop (HP ENVY, WINNING 8) computer I get the following message: "boot device could not authenticate press enter to ' when I have c: it stops. I can't boot into recovery mode either. What the hell went wrong?

  Well, I decided to bring it to the store from my friend, he is a technician and then of course he actually decided that he would start the operating system. He wasn't healthy but, we tried a refresh, but it stopped in the middle of it due to a disk hard w / the question. After that some of diagnotics hard drive was the culprit, so after a permutation we run once again. I'm fine w / start again as it works now. And I called HP ordered my backup disks. Thanks for the help, I would have had the discs that we would have come to the same conclusion I'm sure.

• Laptop cursor jumps back to the top whenever you press SPACEBAR

  Where I work, we have 6 laptops Toshiba Tecra, a few M3 & some M5.  We have one (an M3) as the cursor jumps at the top of the screen whenever the space bar is pressed, in any program (other non-Microsoft), & no matter how lightly or hard the space bar is pressed.  The machine has been completely recreated several times without any change.  The same image is on all our office & laptops.

  thewhitefella,
  You can ask your question in the forum hardware and drivers .
  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Pavilion 17-g108na: selected boot Image is not authenticated

  Dear Sirs

  I provide a laptop HP with windows 7 in the course of running for my clients.

  I bought a HP Pavilion 17-g108na and bought Windows 764 bit on a DVD.

  When I want to boot from the DVD, I get the error message:

  "The boot image selected is not authenticated to. Press enter to continue. »

  Is someone can you please tell me what I should do to get windows 7 installed.

  This would be much appreciated!

  Best regards, Chris

  Hi Chris,

  If you want to install Windows 7, need to disable secureboot and activate the start mode inherited so he could run.

  

• selected boot image is not authenticated

  I just bought a new HP ENVY-4 with pre-installed Windows 8.

  After a few weeks where it has worked well, the computer began to get into trouble. Then he simply did not start more. As I shitch, stay for a while with black screen and then a blue mask pops up saying 'the boot image selected is not authenticated to. Only chance is so press ENTER, then the computer off completely.

  I am hollow your forum and try to almost everything.

  Tools of recovery to run, but not to solve. After treatment, the problem is still there.

  I noticed that if I try to run the "repair of the problems at windows startup" tool, computer said it was not able to repair...

  I open BIOS and changed the relevant setting ensure also the start-up and mode inherited... the computer simply does not start!

  I finally re-formatted the french PC key to restart USB, (made with the HP support tool, when it was new)... same problem appear like I'm back!

  Can you help me please? 3 months computer brand is new and I really disappointed to trow away my money.

  Thank you

  effebbi,

  If your battery off not easily with a lock at the back of the laptop, you can hold the power button for 30 sec with the power cord removed to do the same.

  I would like to know how everything goes

  Nice day.

• Satellite C660: message: reboots and select good boot device

  Hello

  I dropped the laptop today literally a few inches from the ground, it slipped from my hand as I was placing it on the ground. He fell flat.

  Now I see the message "reboot and select proper boot device."

  I tried a few different options that I read, and I see the HARD drive in the BIOS F2 thing or whatever it is called. If it is recognized, but I can't seem to move in the message. Any suggestions?

  Thanks in advance.

  PS I will need clear instructions, I'm not stupid, but I need to explain. I don't understand some of the pieces.

  Thank you

  Hello

  I think that your HARD drive is bad.
  I think that you have not checked it correctly in the BIOS.

  Please go to BIOS once more, by pressing F2.
  Now on the first page, you will see date, time, details of CD/DVD drive and you should also see the details of the disk (size, name)
  You see that?

  Otherwise, the HARD disk is not initialized by the BIOS and this means that, because of the fall, the HARD disk has been damaged.

• Cannot start the computer, the error message "Reboot and Select proper Boot device or Insert Boot Media in selected boot device and press a key any."

  Original title: can't access my BIOS, but blocked on select boot device

  I have a laptop Toshiba Satellite Pro. I gave up some time ago and removed the HARD drive to see if has been affected by the decline, as that was my first thought. "When turned on the laptop back, the error message:" Reboot and select clean boot device or Insert Boot Media in selected boot device and press a key. My HARD drive is installed correctly, that am a qualified technician. The laptop goes directly to this error message, when turned on, so cnnot access to the BIOS. Help, please.

  Hi Ryan,

  Please contact Microsoft Community. I will surely help you this question.

  To better understand the issue, let me know if you have tried pressing the F12 key or the key that is used to start the BIOS on the computer?

  Method 1:

  You may need to press the key (which is used to start-up the BIOS) as soon as you turn on your computer before Windows starts. See the article for more information.

  http://forums.Toshiba.com/T5/Windows-7-knowledge-base/how-to-enter-the-system-BIOS-on-Windows-7-computers/Ta-p/275629

  Method 2:

  If the problem persists, I suggest you to return the item and check if it helps.

  What can I do if my laptop Windows 7 or Windows Vista does not start?
  http://forums.Toshiba.com/T5/computer-troubleshooting/what-can-I-do-if-my-Windows-7-or-Windows-Vista-laptop-won-t/Ta-p/285717

  If the problem persists, I suggest you to contact the Toshiba Support for assistance.

  http://support.Toshiba.com/support/home

  Hope this information helps. Reply to the post with an up-to-date report of the issue so that we can help you further.

• Trying to create a bootable USB I get message error "ISO image selected is NOT a valid ISO file.

  Questions of ISO image

  I'll try to find a way to install Win 7 64 bit Pro - on multiple (without a DVD player) netbooks and thought I had found the solution using DigitalRiver to upload a picture ISO of the OS - then (using the MS Windows 7 DVD/USB tool) - create a BOOTABLE usb key?

  However, yesterday I downloaded the image ISO (http://msft-dnl.digitalrivercontent.net/msvista/pub/X15-65805/X15-65805.iso)

  (which, according to the website of souce was supposed to be 3 GB in size - but was 2 GB in size (WHY?)

  And on the use of the tool USB - a got a message error "ISO image selected is NOT a valid ISO file"

  -What this means and what I can do to work around this problem?

  And, I think - that this procedure works with a "corporate license"?

  Tried - same result - the file is obviously corrupt
  I ended up using a previous download that works!

• Lightroom displays all images from a folder - it displays the message '45 65 images, selected 45' and 45 messages do not appear in the grid of the library, but I can't see the remaining images of 20. All filters are disabled...

  Lightroom displays all images from a folder - it displays the message '45 65 images, selected 45' and 45 messages do not appear in the grid of the library, but I can't see the remaining images of 20. All filters are disabled...

  Hello

  Please go to the library Module, then click on the picture in the Menu bar and then click the stacking.

  From there please select expand all stack them.

  It should show all the images if they are virtual copies.

  Kind regards

  Tanuj