HP build flex 2.0 Pavilion a1709n holding deskjet always does?

Similar Questions

• HP Pavilion G6 computer 1093SA laptop does not charge when I plug in the power adapter

  HP Pavilion G6 computer 1093SA laptop does not charge when I plug in the power adapter

  The battery is dead. When I try to turn on the laptop by plugging the AC adapter does not charge or led power LED does not turn on. But when I press the power button, the power, the indicator flashes and turns off (when power adapter connected).

  (1) I tried the press and holding the power button for 30 seconds after removing the battery & AC adapter / CC.

  (2) I tried to change the power adapter too.

  The problem is that it is.

  Your advice is very much appreciated.

  Thank you best regards &,.

  Zia

  Dear customer,

  Welcome and thanks for posting your question on the Forum of Support HP

  It seems that you are not able to turn on the laptop and tried to solve the problem

  Please perform steps listed to find out if it is a hardware or software problem below:

  1. remove all cables and devices, disconnect them and try to turn on the device

  2. check the LED light situation and ensure the action of the spring button / stop is normal

  3 Exchange with a well known power cord and the AC adapter

  4 Pack no adapters are available, check if the power adaptor is slightly warm

  Note: This will give us an indication that the power adapter could be good

  5. do you know if the laptop was in battery or power adapter when you used the last time

  Note: Make sure that there is no spill of liquid or cutting

  6. check if the Port of the AC adaptor is loose/broken

  Note: If the laptop is not on even with a power adapter well known, this confirms the hardware failure with the system board or power DC Circuit

  Hope this helps for other queries to answer the post and feel free to join us again

  * Click on the star of CONGRATULATIONS on the left to say thank you *.

  Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

  Thank you

  K N R K

  I work on behalf of HP

• My hp pavilion elite hpe-204f video does not work

  My hp pavilion elite hpe-204f video does not work so I replaced it with another video card that worked. After installing the card and start the system I saw the video on my monitor. Great! I need to replace my video card. No problem.

  Afer by purchasing and installing a new video card, I have no video. I put a new one in another computer. This works. I put the video card which worked yesterday... that did not work.

  Then, I put the original video card that I thought that did not work on another computer and Yes... it worked.

  Should I assume that I have a bad graphical location on the motherboard? If so, short of buying the same motherboard is there anything else I can do?

  Thank you very much for the research.

  Hello

  The integrated video processor still works when the video card is removed?  If Yes, then try this memory bootable Diagnostics CD. Download memtest86 iso file and burn the disk using Imgburn.

  If the above is successful, then re - install the map graphic and clear the CMOS.

  Another thing to try:

  A good cable video know.

  A known good monitor.

• I have a HP Pavilion notebook. My system does not detect my sd card and I can't eject. Help?

  Original title: undetected sd eject not

  I have a HP Pavilion notebook. My system does not detect my sd card and I can't eject. Help?

  From my understanding, most laptops allow you to simply remove the SD card back.  Others have a simple spring mechanism that requires you to press the memory card slightly until you hear a "click", similar to a click on a retractable pen, which must eject the card.

• Pavilion dv6 Notebook: laptop still does not start if equipped upward of battery

  Pavilion dv6 daughter Notebook always primer not beyond the screen HP enrobeur battery if

  Product number: WR498EA #ABU
  Serial number: [personal information deleted]

  Operating system: Windows 7

  Hello @HPNovice1,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I understand that your notebook always primer if if mounted battery and I'd love to help you in this case!

  Since you have already calibrated and tested the battery, I suggest following the steps below re - install the battery method compatible ACPI Microsoft control:

  Step 1. Go to the Device Manager
  Step 2. Select the stacks
  Step 3. Click with the right button on the "Microsoft compatible battery ACPI Control method" which is in the list
  Step 4. Click on uninstall
  Step 5. At the command prompt, put a checkmark in the box to remove the current driver
  Step 6. Shut down the computer
  Step 7: Remove the battery for a minute and then put new

  When the computer returns to the top it should automatically find the driver.

  Step 8. Go to the Device Manager
  Step 9. Select the stacks
  Step 10. Click with the right button on the "Microsoft compatible battery ACPI Control method" which is in the list
  Step 11. Click "automatically search for an updated driver.

  Do the same thing with embedded controller compatible ACPI Microsoft.

  In addition, I also recommend you to restore your laptop default power plans by following the steps below:

  Step 1. Click the Start button
  Step 2. In the search box, type "Command Prompt"
  Step 3. Right click on command prompt

  Step 4. Click on run as administrator
  Step 5. At the command prompt, type powercfg /restoredefaultschemes and press enter

  reference: http://superuser.com/questions/669571/Windows-8-1-64-bit-power-schemes-gone

  If the problem persists, please call our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number.

  http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  I hope this helps!

  Concerning

• Building Flex SDK

  I have download the Adobe Flex SDK 4.6, modified the DropDownController.as file, run the ant script to generate her updated the SDK.

  I created the Flex with this updated SDK project, but still the old code is reflecting instead of the updated SDK.

  What I am doing wrong.

  (PS: I try to avoid making the monkey patching)

  I think monkey patching is much easier.

  If you use RSL, then your changes will not be in the official RSL and you will need to monkey patch.

  If you are linking static libraries then what you should work even if Flash Builder requires a reboot that it can cache the old SWCs.

  -Alex

• test fails when building - flex-pmd-ruleset

  Hi, I followed the developer documentation for how to generate the project in step 7 that fails because the following tests fail inside flex-pmd-ruleset:

  Tests failed:
  testProcessViolatingFiles (com.adobe.ac.pmd.rules.unused.UnusedLocalVariableRuleTest)
  testBuildMessageName (com.adobe.ac.pmd.rules.core.EmptyRuleTest)
  testProcessViolatingFiles (com.adobe.ac.pmd.rules.naming.WronglyNamedVariableRuleTest)
  testProcessViolatingFiles (com.adobe.ac.pmd.rules.unused.UnusedPrivateMethodRuleTest)

  Tests: 219, failures: 4 errors: 0 ignored: 0

  [INFO] ------------------------------------------------------------------------
  [ERROR] BUILD FAILURE
  [INFO] ------------------------------------------------------------------------
  [INFO] There are test failures.

  I don't know how to correct these failures, clues as what may be the problem? I have run "mvn package" flex-pmd-parent of the command line.

  TIA,

  Magnus

  I use 1.5 as a JAVA virtual machine indeed.

  You can synchronize again, please?

  All the differences using mvn install?

  Xavier

• How to compile flex builder flex sdk project?

  I built a flex with flex builder project and wish to modify and maintain in an environment of the flex SDK.

  I wonder if there is no tool in flex sdk to do this.

  Thank you

  You can use Ant tasks

  http://livedocs.Adobe.com/Flex/3/HTML/Help.HTML?content=anttasks_1.html

• Building Flex without MXML but with AS3 applications

  It seems logical that if I want to build an application I should use AS3 to create reusable components, classes, the layout, etc.
  
  .. However, looking around on the web exclusively finding Flex tutorials and examples using MXML. This also applies to the books (for example Adobe Flex 2 - training from the source) - why is - this?
  
  Is it wrong of me to think that it would be better to create everything in AS3? Someone has links to tutorials etc where they use AS3 to create Flex applications?

  I don't think that there is nothing wrong with assistance regarding your components - I do for most of my components if they are not containers available inside of them.

  Using FlexBuilder gives you the ability to graphical layout, and that is something good and useful to use for layout components. If I extend a control and change his behavior I always use because it's a bit awkward to do in MXML, and there is no benefit to it. Sometimes, however, I am creating a component to be used, for example, as a popup - in this case, I create a mxml file that extends from TitleWindow and I can use the visual layout of the content editor.

  In any application, you need to end up with something of Visual that involves the layout, so it is rarely likely to be an argument not to use MXML, at least for the Application. There is no runtime performance gain to use LIKE - even if I assume that the compiler saves a little time.

  So in your example, I agree there is nothing wrong with this if the app:Test class is fully dynamic, but if you do a static layout inside the Test class you just cryptic for yourself and for any developer to keep this code in the future.

  Tim

• wanted to build a vi to simulate the hold on a Panel button.

  Hello

  Were to simulate a press and hold on a Panel button to turn on the rest of the buttons on the Panel.

  Kind of extreme, used case Acquire of entry data, index table, structure (boolean), all in a while loop.

  No comments for this approach or any ideas appreciated,

  The vi can be downloaded on request.

  Rgds,

  David

  
  

• Pavilion g7-1368dx "cooling fan does not work correctly.

  Greetings. I have a HP Pavilion g7-1368dx laptop with Windows 7 I bought in June 2012, is no longer under warranty.

  A few weeks ago he had a thermal cut-out once during use. After cooling, the laptop works very well for a few uses, but then it has started giving the boot warning message, "the system has detected that a cooling fan is not working properly," with an additional indication of the damage if the computer is used in this State.

  I ordered a new fan and succeeded him, and I cleaned the fan grille in the process (although it wasn't very dirty), but I still get the same fan error message. I went to the HP website and saw the suggestion to do a "hard reset", so I did it, but the problem persists.

  I saw another suggestion to try a BIOS update, but I thought that would not be desirable because the fan does not work. Suggest you go through with the attempt to update the BIOS anyway?

  Is there something else I can try before ordering a new card system?

  Thanks for your help.

  Dear customer,

  Welcome to the Support Forum HP and we are happy to help you

  Looks like you are having difficulties with regard to your laptop cooling fan
  We will surely help you with this

  According to the message that you have posted, I suspect that it is purely a matter of material where in your message 'System Fan(90B) - the system has detected that a cooling fan does not work properly' get. It is a mechanical failure and fan cooling of your laptop and must be replaced before the laptop starts with an overheating problem.

  Causes/reasons for this problem:

  1. sometimes, it's just because of the dust, animal pet hair slows down the fan

  Perform the illustrious below troubleshooting steps:

  Step 01. Turn off the laptop

  Step 02. Disconnect the power/AC adapter and also remove the battery too

  Step 03. Press and hold the power button of the laptop for a minute

  Step 04. Now re - insert the battery back in and plug again the power supply/adapter

  Step 05. Start Notepad and keep pressing the F10 key during startup to access the BIOS

  Step 06. Once you get the BIOS, please press F5 to load the default Installer for BIOS

  Step 07. Now press ESC/ESC. Save Changes and Exit - Yes

  Step 08. Now please wait unit loads Windows and then stop the Netbook again

  Step 09. You need to clean all vents and openings that are really good with a can of compressed air

  Note: If you still get the same error, we need to replace the fan

  I highly recommend you Contact HP technical support immediately by phone to get help immediately to get your fan replaced and serviced by an authorized HP Certified Engineer Netbook

  Click on the link to check the status of warranty below
  http://tinyurl.com/6cf8qju

  Hope this helps, for other queries in response to the post and feel free to join us again

  * Click on the star of CONGRATULATIONS on the left to say thank you *.

  Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

  Thank you
  K N R K
  Although I am an employee of HP, I speak for myself and not for HP

• Flex 3 beta 3 + Eclipse (Europe) 3.3 + does not

  Hello
  
  I just installed it about 10 times with an Eclipse installation "new & clean" and all referred to preparations for cleaning system (e.g. Zero G registry...). Installation of FB 3 beta 3 worked without any errors. After that I have launch Eclipse with the "Adobe Flex Launcher" in the menu it opens also as expected, but... when I try to do an action that is based on the Flex plugin an error dialog box comes up and tells me s.th. like (depending on the action) "... failed to load com.adobe.flex.
  After several standard installations, I also tried to copy all the files of 'features' and 'plugins' for the installation of Flex in the eclipse records but the same problems.
  
  Any help would be fantastic!
  Thanks in advance!
  
  Erik

  Yay! I got it!!! ... or better we got it!

  Your tip with "-clean" has been a part of it... so take a seat and read this:

  I had my 21. Try to install... I have Eclipse 3.2 working with FB 3 beta 3, but my first choice would be with Eclipse 3.3.1.1... and I won!

  After uninstalling FB 3 beta 3 and Eclipse folder removal and cleaning of the system, I unzipped Eclipse and reinstalled FB 3 beta 3. Here's what I found:

  -After unpacking Eclipse the "eclipse.ini" contain only of standard settings
  -J' started Eclipse once and set my specific workspace folder.
  -For installing FB 3 beta 3 Setup adds some special parameters to the "eclipse.ini"... why you Adobe guys should know, don't you ;-)
  -L' one of the special parameters added while the installation was "-CLEAN".
  -J' just deleted the file parameter and started FB 3 beta 3

  Now, everything comes to an end very clear... for sure Eclipde survey of errors like "com.adobe... not found" every time I start Eclipse it cleans all and also the modules plugin Flex Builder!

  I hope this bug report is pretty good and helps a lot of people out there who should never have the same problem.

  Thank you for you inquiry to solve my problem!

  Concerning
  Erik

• Press and hold the menu does not appear while composing email - iOS 10

  As per above, if you press and hold before type anything, the submenu would not appear.

  You must type something in front first, then press and hold to see the submenu.

  As on the new line without typing anything, submenu just appear in press and maintenance.

  This has never happened before on iOS 9, as I always have right now to insert any picture without typing anything.

  This is a bug in ios10. Thought I was going nuts trying to re - copy text in a different application and bring it back on my mail.

• Pavilion 15 ab034tx: fan speed does not synchronize with the temperature of the cpu all in game.

  Although playing high graphic games CPU overheats and the game stops working after 5 minutes of play. So please make changes to bios fan settings.

  Hi @abhishekkm,

  Welcome to the HP Forums!

  In your post, you said that currently your HP Pavilion Notebook 15-ab034tx is overheating. You can restore the BIOS by default, as this has helped other people with this problem. Here is a document that will show you how to proceed.

  Please let me know.

  If you want to say thanks for my efforts to help, click on the thumb to to give me a Kudos.

  Thank you.

• HP Pavilion Notebook (laptop) plugged, G6 does not support.

  Hello

  I bought a laptop HP Pavilion G6 just a couple of months, and I had this problem since the beginning. I looked at some other forums and it seems that many people have had the same problem with the laptop is plugged in, but does not support.

  This problem is really frustrating, as the laptop is connected to the power source and in the laptop, but half the time it is not yet registered as being connected. The battery is discharged. Once or twice the battery completely exhausted (while it's plugged in) and then was charged 100% next time, it was shot on(???!!!).

  Could you tell me if there is some sort of programming or software failure, or if it could be a hardware failure. I have run the checker battery several times and each time he found no problems with it. As the laptop sometimes acknowledges that it is indeed connected (but does not load) personally, I think that it is not a problem with the AC adapter.

  PLEASE HELP ME!

  Thank you.

  (Sorry for the long message)

  Hello

  You can help us help you by displaying the following information.

  1. the complete model number and the laptop Nr - see web document this HPif you're not sure you how to locate the product number or model number.

  2. the full version and the name of the operating system you use (IE Windows 7 64-bit).

  Go to Device Manager. (type device in the search programs and files and click on Device Manager, as shown in the following image)

  

  Expand the device of Batteries.

  Right-click on the compatible Microsoft ACPI control method battery and select uninstall.

  Do the same with the device adapter Microsoft.

  

  After uninstalling the devices, then you can right-click on one of the devices in the Device Manager and select and click on check for material changes.  When you have done this, the operating system will reinstall drivers for the devices.