HP Color LaserJet MFP M570dw and HP Web Services

Similar Questions

• Color LaserJet MFP M277 dw Pro: Setup disk gives an error and stops before the connection to the printer

  Hello

  I try to install the printer 'Color LaserJet MFP M277 dw Pro'.
  By inserting the disc into the phase "installation preparation" is 96% and then stops and gives me the error.
  I use Windows XP SP3. It is always installed, but physically disconnected another printer hp (hp 2050).
  (I tried both to disable the antivirus that reduce to a minimal install, but the problem persists).
  Thank you

  Response thanks a lot.
  In the meantime, I contacted the Support of the Italy
  Who suggested that I try to update the driver.
  I downloaded the file "HP_LaserJet_M277_PCL6_Legacy_Print_Driver_14295".
  Automatic extraction and I launched and everything seems to work.
  (I still try to scan and fax if they work).
  Thank you very much.
  Thanks to your colleague Michelle with whom I chatted.
  Contact thank you for the support of Milan that I don't know the name.
  So, I can communicate the solution found.

• Color LaserJet MFP M477fdn Pro: M477 Software Installation fails at 99%

  Like others who have posted here, I have been unable to get the printer software to complete the installation. The printer is a Color LaserJet Pro MFP M477fdn, 3 months. I'm trying to install the software on a new workstation HP Z240 performing Windows 10 (64-bit). The connection is via USB cable. The printer and the software have been previously used with a Windows 7 machine without problem.

  I tried, repeatedly, to install the software from the disc supplied with the printer and also a 126.6 mb download HP Color LaserJet MFP printer M477 Pro series full software and drivers. The results are the same with a source - installation apparently progresses up to connect it the indicator product of progression from screen reached 99%, how it gives an error message "a Setup operation took too long to run. It is a fatal error, preventing the use of the product. Restart your computer and run this installer again. If the problem persists, please visit the web site of product support for your product. "It takes about 20 minutes for the phase of installation to go from 0 to 99%, and then later hooked up to 99% for 2-5 minutes, the error message is displayed.

  I am able to print to this printer, but at least do not have the ability to scan from the computer there is no indication that the I.R.I.S. OCR software is installed.

  I had care of do not connect USB until you are educated.

  I tried repeating the installation without uninstalling first and get the same result.

  I used the uninstall contained the disk feature, and have deleted the printer to the computer using the Panel between the installation attempts.

  I tried to do a right click to run the installer as administrator and get the same result.

  I tried to install after clean boots with turned off Windows Firewall and all functions of the software Norton Internet Security including its function of firewall turned off.

  The event viewer displays none error entry at all and no entry identifies HP as the source of an event.

  I tried to connect via USB 2.0 and 3.0 ports.

  I cleaned recycle them and temporary folders.

  I have updated the firmware of the printer to the 20160331 version.

  Printed printer configuration report will not display any errors, nor that the printer itself indicates something is wrong and confirms the update of the firmware.

  I deselected the optional software, the devices experience HP and I.R.I.S. OCR, trying to install only the required files two more program scanning HP.

  Thanks for any help solving this.

  I think I understood the question, 10 windows installs its own driver, and the installation program expects the hp driver to install.

  DO this FOR THE HP INSTALLER PROCESS (when the percentage meter goes)

  1. go into the Device Manager and find the printer in the list of devices

  2. right click on the printer and select "Update Driver software"

  3. click on "Browse my computer for driver software".

  4. choose "Let Me pick one...» »

  5. Select the named driver: HP Color LaserJet MFP M477 PCL-6 Pro (make sure it's one with a dash between the pcl and 6!)

  6. click next and back to the installation of hp box and must now see the printer and continue the installation.

  -Alex

• Color LaserJet MFP M277dw Pro: MFP M277dw unable to connect to wifi

  I just bought the Color LaserJet MFP M277dw Pro, and I can't connect to wifi. I have it connected via a USB cable and it works fine, it's just that I can't seem to connect to my wifi. The wifi seems fine, just connect my existing devices right (MacBook, iPhone, iPad). It finds the network, but it seems to expire when I put the password to connect.

  Hi @StephanieB2,

  Welcome to the Forums of HP Support! I understand that you are having problems with the networking of the printer. I want to help you solve this problem. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  It's really weird that the printer is expire when you put the network password.

  Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.

  You can also configure the printer on the wireless network, thanks to the Wi - Fi Direct connection.

  Tap the icon on the screen of the printer wireless.

  Select the Wi - Fi Direct connection.

  Turn it on, if it isn't already, and if there is a code it marks down.

  Then on the Mac, go to the airport icon and connect to the network printer. (Direct 69 HP Laserjet M277)

  If requested a code or password, put the one you noted.

  Then open Safari and type 192.168.223.1.

  He will be responsible: the printer Web server integrated.

  Click the network tab.

  On the left side of the window, select Wireless Network Configuration and fill your information.

  Apply the settings.

  Can connect you to your network.

  Then add the printer.

  Click on the Apple menu, click System Preferences.
  Scanners & printers, then click the plus sign +.

  Select the printer in the list.

  Select your printer from the drop-down and click on the Add button.

  Test the printer.

  If there is anything else I can help you, let me know. Thank you.

• HP Color Laserjet M277dw MFP: Cannot scan HP Color Laserjet MFP M277dw on Mac OS 10.6

  Hello, I can not scan to network drive using the above mentioned printer. Scan to USB key is possible.

  I downloaded the update (version 20160331) firmware image, but impossible to install the program. After double click, nothing happens. Any ideas?

  Thank you and best regards

  Christoph

  Hi Christoph,

  The printer is not compatible with Snow Leopard, it is supported on Lion (10.7) or later versions.

  You can find the system requirements below:

  http://support.HP.com/us-en/product/HP-Color-LaserJet-Pro-MFP-M277-series/7089945/model/7089949/document/c04515051/

  The update of the firmware utilitywas not desinged for your operating system and therefore does not work on it.

  As the connectewd printer to a network, follow these steps to update firmware directly from the menu of the printer:

  http://support.HP.com/us-en/product/HP-Color-LaserJet-MFP-M277-series/7089945/model/7089949/document/c04517106/

  If the implementation of scan to a shared folder on your grave down Mac, please specify the exact error, and the parameters used (path of the shared folder used, etc.) also well done you have shared this folder your Mac form?

• scan to email on Color LaserJet MFP M177fw Pro

  I'm trying to download the printable 'Scan to Email' on my Color LaserJet MFP M177fw Pro, but he continues to throw an error?

  When I bought the printer (yesterday), I was told that I could put up to Scan in a document and have it automatically send as an e-mail message to a recipient.  How to achieve this?

  Thank you!

  Hi grahammccarthy,

  Welcome to the HP Support forums.  I understand that you want to know how to scan to email using your printer Laserjet Pro MFP M177fw.

  You don't mention the operating system that you use, so I've included links to all the operating systems supported on the way to analyze.  There is a section called "How to scan with HP software" and there you can find a subsection entitled "How to scan to email.  It is in the subsection, you will find the instructions you need to follow to be able to scan to email.

  How to perform a scan: Windows XP

  How to perform a scan: Windows Vista

  How to perform a scan: Windows 7

  How to perform a scan: Windows 8

  How to perform a scan: OS X v10.8

  How to perform a scan: OS X v10.9

• Color LaserJet MFP M177fw Pro: Scan to Mac with Color LaserJet MFP M177fw Pro

  I bought and the latest drivers from hp installation a HP Color LaserJet Pro MFP M177fw. are downloaded and installed.

  I have a Mac and you connect wirelessly to the printer, which works very well. The Mac runs Yosemite 10.10.3

  My question is the digitization. There is no option for scanning anywhere, not on the small screen of the printer not on the usefulness of the printer or any where.

  Summer spend hours online to find an answer and is now well bored.

  I have already reset the disc printing, verified and repaired systems. Can not scan even with the options offered on the forums of hp using Apple caprure or preview. It seems that all these options include versions of OS X prior to Yosemite?

  I buy a multifunction printer that is not scan? I said to the saleswoman that I need a printer that can scan and airprint...

  Is it possible to scan to a mac at all with this printer? Any help?

  Hi @sa9494,

  I see that you have problems with scanning. I will definitely do my best to help you.

  Check the name of the driver that is installed by the printer. Make sure that it shows just the name of the printer.
  Click on the Apple menu, click System Preferences. Click on Printers & Scanners, highlight the name of the printer on the left side and right side of the screen it should show the name of the printer. (Color LaserJet MFP M177fw Pro)

  If the full name of the printer is not correctly, delete and add the printer name back from the list. Click on the sign - to remove the driver and then click on the + sign to add the driver might have to drop-down list to select the name of the printer to add a click.

  

  

  Here is a screenshot of what it should look like. You have the scanning through top tab?

  

  I have also included a document for HP printers - scan with HP Software in OS X v10.10 Yosemite.

  Scanning ports is not open on the router to the origin of this problem. You can contact the router company to verify and to open these ports 9220/9500/427 on the router.

  Connect the printer with the USB cable, to see if you have the same results.

  Let me know.

  If you appreciate my efforts, please click on the "Thumbs up" button below.
  If you have any questions, please let me know what steps you have taken and the results. Thank you.

• Color Laserjet MFP M277DW Pro: scan to pdf corrupted

  I use Nitro PDF, and every time that I scan to PDF it is said the first page was damaged and has been repaired.   But it is empty, no content on page 1. This will happen if I use the shipper of record or the screen.  I just bought a new laptop, and there was this problem on my old laptop as well.  Scan to JPEG works but then have to take the extra step to convert the JPEG to PDF and it's a hassle.  Why the first page is always corrupt?

  Hello

  Do you have installled of Adobe Reader on your PC? (even if not used as the default viewer)?

  As you can find the system requirements below, it is part of the configuration required to make full use of the printer:

  http://support.HP.com/us-en/product/HP-Color-LaserJet-MFP-M277-series/7089945/model/7089949/document/c04515051/

  Try to install it starting from the following link, then try to scan the image:

  http://get.Adobe.com/reader/

  Now try to open the file with Nitro PDF, if the same persists check if you can see a difference with Adobe Reader.

  Shlomi

• Color LaserJet MFP M177fw Pro: Color LaserJet MFP M177fw Pro

  I have Color LaserJet MFP M177fw Pro and it is stuck on print fax. I restart the printer and print the fax even. I found a post and supposed to go ware closes so I did. Printer is returned to normal. Got another fax and the printer to print fax. I tried firmware ubgrade once again without help. Toolbox program HP device says 'Printing Fax Page 1'

  Also I can't receive any new faxes and print to the device.

  Hi @DDTKS.

  Welcome to the FOrums of HP's Support. I understand that your Laserjet M177fw is stuck to print a fax. I would like to help.

  I sent you the steps to perform initialization of the NVRAM via private message.

  If you are unfamiliar with the operation of the function of private messages of the Forum, this posthas instructions.

• color laserjet MFP M177: error message when you try to print

  Hello

  I have a HP Color laserjet MFP M177.  I can't print I get an error message on my computer screen. No messeage shows up on the printer.  I have recently upgraded to windows 10 (I do not know what version) If this could have something to do with it?

  Help, please

  Thank you

  Hi @Daisy001,

  Welcome to the Forums of HP Support! I see by your post that you can't print, since the upgrade to Windows 10. I will definitely do my best to help you. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  If you have not completely uninstall and reinstall the driver, I would say to start it there first. Here is the link to the latest drivers: Color_LJPro_MFP_M177_full - solution_15188.exe

  If the problem persists, you can download and run the print and Scan doctor, he will diagnose the problem and could solve it automatically.

  Please let me know the results and if there is anything else I can help you. Thank you.

• Color LaserJet MFP M177FW Pro: 126 a Toner can be used with Color LaserJet Pro MFP M177FW?

  I recently bought a Color LaserJet MFP M177FW Pro and still have 126 a toner cartridges (magenta, cyan and yellow) for my LaserJet MFP M175 precedent. I can use them rather than the cartridges of 130a recommended?

  Hello

  Only 3 printers can use HP 126 has:

  http://WWW8.HP.com/us/en/products/OAS/product-detail.html?OID=4148379#! tab = compatible_hosts

  Kind regards.

• HP color laserjet 2840 printing and copy blank page

  Hi all

  I have hp color laserjet 2840, printing and copy empty, I change the toner and drum but nothing! any idea?

  Sorry for my bed English

  Thank you

  Try this test.

  Printed page in after you get the blank page open the access door and see if you can move the carrousel by hand.

  If the carousel will rotate the carousel latch is stuck.

  The lock can be fixed by disassembly of the valve and clean some foam sticky residue deteriorated and its replacement by a thin piece of material. I use stickers very thin markers of a dollar store.

• Import questions of outgoing and incoming Web services in Siebel Client 8.2

  Impossible to import the outgoing and incoming Web services in Siebel Client 8.2 (Public sector) according to the installation instructions:

  Import the outbound Web Services

  To import the outbound web service, follow these steps:

  1. go in Administration-> Web Services-> outbound Web Services

  2. click on import in the outbound Web Services applet

  3. click on browse in the dialog box presented

  4. open the file < install_dir > /examples/SmokeTest/OutboundWebService.xml

  Oracle policy Automation Connector for Siebel Manual of Installation V10.3.0 23

  5. click on import in the dialog box presented

  6 highlight the DeterminationsServer file

  7. change the address < ds_url > /savon / AdminSmokeTest in the Ports of Service applet

  8. Repeat steps 2 to 7 Choose file

  /examples/SmokeTest/OutboundWebServiceIO.XML < install_dir >

  Import incoming Web Services

  To import the outbound web services, follow these steps:

  Go to Administration-> Web Services-> inbound Web Services

  1. click on import in the incoming Web Services applet

  2. click on browse in the dialog box presented

  3. open the file < install_dir > /examples/InboundWebService.xml

  4. click on import in the dialog box presented

  5. turn highlighted the strategy of automation Inbound folder

  6 edit each entry of addresses in the name of the machine hosting the Server Web EAI_Anon_Enu

  Extension, in the Ports of Service applet

  7. Repeat steps 2 to 7 Choose file < install_dir > /examples/InboundWebServiceIO.xml

  Nothing is imported to. Has anyone observed this problem? I use Siebel OPA 10.3.1 connector.

  Concerning

  Bhaskara

  you follow step manual installation that is a bit laborious.

  I think that you will get to see definitions of IO only after enabling view policy automation.

  I will propose you to complete all the steps and then check.

  in my view, import the RIS file will be easy compared to a manual installation.

  Thank you!

  Ravi

• Basic authentication with the RESTful WEb service and a Web Service reference

  Hi all
  
  We have made significant progress on getting an application to work with RESTful web services, but are now trying to understand how to lock a RESTful Web service while making it available for a particular application.
  
  We use one of the 'emp' table sample web services come with Apex 4.2 and are trying to apply the Basic Auth to the WEb Service using Weblogic filter defined in the web.xml file. Which works very well. I now get challenged when I try to go to:
  
  https://wlogic.edu/Apex/BNR/ACE/HR/empinfo/
  
  And when I authenticate this challenge, I am able to get the data. (we are usiing the Weblogic-level LDAP authentication)
  
  However, I'm not sure how to get even basic authentication to work with Web Service reference in my application. I see the error message in the application when I try to call this Web Service:
  
  401 Unauthorized <
  
  And I see:
  "The request requires user authentication. It MUST contain a header field WWW-Authenticate (section 14.46) containing a fault that is applicable to the requested resource. The client MAY repeat the request with a suitable authorization (section 14.8) header field. If the request already includes identification of the authorization information»
  
  How can I provide the credentials in the Web reference or provide credentials in the Application?
  Web service works fine if I remove the auth basic RESTful web service in the Web.xml file.
  
  We should NOT use basic auth and auth Weblogic web service definition basic RESTful Workspace use instead. If so, how would we implement THIS basic authentication in the definition of Web Service and the Web SErvice reference on the application?
  
  Thank you
  Pat

  Hello Scott,

  Thank you. There is a function for rest in the package:

  function make_rest_request(
  --
  -- This function invokes a RESTful Web service with the supplied name value pairs, body clob, or body blob
  -- the response as an clob.
  --
  -- Arguments:
  --   p_url                  The url endpoint of the Web service
  --   p_http_method          The HTTP Method to use, PUT, POST, GET, HEAD or DELETE
  --   p_username             The username if basic authentication is required for this service
  --   p_password             The password if basic authentication is required for this service
  --   p_proxy_override       The proxy to use for the request
  --   p_body                 The HTTP payload to be sent as clob
  --   p_body_blob            The HTTP payload to be sent as binary blob (ex., posting a file)
  --   p_parm_name            The name of the parameters to be used in name/value pairs
  --   p_parm_value           The value of the paramters to be used in name/value pairs
  --   p_wallet_path          The filesystem path to a wallet if request is https
  --                          ex., file:/usr/home/oracle/WALLETS
  --   p_wallet_pwd           The password to access the wallet
  --
      p_url               in varchar2,
      p_http_method       in varchar2,
      p_username          in varchar2 default null,
      p_password          in varchar2 default null,
      p_proxy_override    in varchar2 default null,
      p_transfer_timeout  in number default 180,
      p_body              in clob default empty_clob(),
      p_body_blob         in blob default empty_blob(),
      p_parm_name         in wwv_flow_global.vc_arr2 default empty_vc_arr,
      p_parm_value        in wwv_flow_global.vc_arr2 default empty_vc_arr,
      p_wallet_path       in varchar2 default null,
      p_wallet_pwd        in varchar2 default null ) return clob;
  

  My point was that using the API makes things easier if you have to look for a solution.

  Denes Kubicek
  -------------------------------------------------------------------
  http://deneskubicek.blogspot.com/
  http://www.Apress.com/9781430235125
  http://Apex.Oracle.com/pls/Apex/f?p=31517:1
  http://www.Amazon.de/Oracle-Apex-XE-Praxis/DP/3826655494
  -------------------------------------------------------------------

• What is the difference between "vShpere SDK ro Perl"and "vSphere Web Services SDK (for Java or c#)"?

  Hello world! I'm new to "VMware vSphere API", and I have a question to ask you to help:

  What is the difference between "vShpere SDK ro Perl"and "vSphere Web Services SDK (for Java or c#)"?

  -What are the different programming language? Is there another difference?

  I'm looking forward to your reply.

  Thank you!

  If you are new on the VMware API/SDK, highly recommend you take a look at the following: Getting Started with vSphere SDK - Update for SDK 4.1 release

  vSphere SDK for Perl is just one of the many client SDK for vSphere API that is flush with vcenter times and ESX (i) as a standard Web service.

  vSphere SDK for Java - SDK Java to vSphere API for Java developers

  vSphere SDK for Perl - Perl SDK for vSphere API for Perl developers

  vSphere SDK for c# - c# SDK for vSphere API for c# developers

  PowerCLI - PowerShell SDK for vSphere API for developers of Powershell

  I hope that makes a bit more sense

  =========================================================================

  William Lam

  VMware vExpert 2009,2010

  VMware VCP3, 4

  VMware VCAP4-DCA

  VMware scripts and resources at: http://www.virtuallyghetto.com/

  Twitter: @lamw

  repository scripts vGhetto

  Introduction to the vMA (tips/tricks)

  Getting started with vSphere SDK for Perl

  VMware Code Central - Scripts/code samples for developers and administrators

  VMware developer community

  If you find this information useful, please give points to "correct" or "useful".