HP Compaq 6200 Pro small format: Re-install the network adapter

Dear assistants & members,

Yesterday, I tried to download a 64-bit system that has not worked and had trouble.

I am trying to connect to the internet, but it still says: a network adapter was not found (something like that)

I have seen a lot of messages so I already do my hardware ID:

PCI\VEN_8086 & DEV_1502 & SUBSYS_1497103C & REV_04

PCI\VEN_8086 & DEV_1502 & SUBSYS_1497103C

PCI\VEN_8086 & DEV_1502 & CC_020000

PCI\VEN_8086 & DEV_1502 & CC_0200

I hope you self-introduction can help out me.

I'm computer: HP Compaq 6200 Pro Small Form Factor

Hello:

Try the driver directly from Intel.  The hardware ID you posted is for an Intel ethernet card.

The first file listed is for W7 32 bit.

https://Downloadcenter.Intel.com/download/18713/network-adapter-driver-for-Windows-7-

I was going to ask...

How did you couldn't get W7 x 64 install?

I have an Elite 8200, which is the same model as yours, except that it's a chipset series 6 Intel a little better than you do.

I had no problem installing W7 x 64 on it.

Tags: Notebooks

Similar Questions

  • HP Compaq 6200 Pro small-format: How can I tell how old my computer is by serial number

    I would like to know how old my computer with the help of its serial number.

    HP Compaq 6200 Pro Small Form Factor PC

    Serial number: [personal information]

    I hope someone can tell me when my model was in production and sometimes identify the date that your machine was completed.

    Thanks in advance.

    Best,

    Renata

    Rena.

    Your computer was born.

    Week 07February 13, 201219 February 2012

    Year 2012 week 07

    REO

  • HP Compaq 6005 Pro small format: error installing Windows 7 64 bit

    I install windows 7 64 bit, an error message, please guide me how to solve this problem

    thainguyenvl

    Hello;

    Let me welcome you on the HP forums!

    Unfortunately, the image you posted does not in the forum - then please provide the error text.

    We can proceed once you provide the information.

    Thank you

  • ESXI how to install the network adapter driver

    Hi all:

    My ESXI5.5 has been installed, but find that the network card can not be identified, how to install the network adapter driver.

    Thank you very much

    Hello

    Follow the VMware KB for the installation of the NIC driver, hope it helps.

    VMware KB: Cards not detected on a host ESX ESXi network

  • VMware Workstation 12.1.1 Pro is unable to install the network grows on CentOS 6.8 host

    Just upgraded my 6.7 CentOS Server (where the VMware Workstation 12.1.1 worked fine) to 6.8.

    After a reboot, VMware has done, it is usual thing where she wanted to reinstall its readers. He doesn't have to install the network component. Here are my logs:

    2016-05-28T18:21:09.477-07:00| vthread-4| I125: Log for VMware Workstation pid=27658 version=12.1.1 build=build-3770994 option=Release
2016-05-28T18:21:09.477-07:00| vthread-4| I125: The process is 64-bit.
2016-05-28T18:21:09.477-07:00| vthread-4| I125: Host codepage=UTF-8 encoding=UTF-8
2016-05-28T18:21:09.477-07:00| vthread-4| I125: Host is Linux 2.6.32-642.el6.x86_64 CentOS release 6.8 (Final)
2016-05-28T18:21:09.476-07:00| vthread-4| I125: DictionaryLoad: Cannot open file "/usr/lib/vmware/settings": No such file or directory.
2016-05-28T18:21:09.476-07:00| vthread-4| I125: PREF Optional preferences file not found at /usr/lib/vmware/settings. Using default values.
2016-05-28T18:21:09.476-07:00| vthread-4| I125: DictionaryLoad: Cannot open file "/home/sa_schewee/.vmware/config": No such file or directory.
2016-05-28T18:21:09.476-07:00| vthread-4| I125: PREF Optional preferences file not found at /home/sa_schewee/.vmware/config. Using default values.
2016-05-28T18:21:09.501-07:00| vthread-4| W115: Logging to /tmp/vmware-root/vmware-27658.log
2016-05-28T18:21:09.511-07:00| vthread-4| I125: Obtaining info using the running kernel.
2016-05-28T18:21:09.511-07:00| vthread-4| I125: Created new pathsHash.
2016-05-28T18:21:09.511-07:00| vthread-4| I125: Setting header path for 2.6.32-642.el6.x86_64 to "/lib/modules/2.6.32-642.el6.x86_64/build/include".
2016-05-28T18:21:09.511-07:00| vthread-4| I125: Validating path "/lib/modules/2.6.32-642.el6.x86_64/build/include" for kernel release "2.6.32-642.el6.x86_64".
2016-05-28T18:21:09.511-07:00| vthread-4| I125: Failed to find /lib/modules/2.6.32-642.el6.x86_64/build/include/generated/utsrelease.h
2016-05-28T18:21:09.511-07:00| vthread-4| I125: using /usr/bin/gcc for preprocess check
2016-05-28T18:21:09.518-07:00| vthread-4| I125: Preprocessed UTS_RELEASE, got value "2.6.32-642.el6.x86_64".
2016-05-28T18:21:09.518-07:00| vthread-4| I125: The header path "/lib/modules/2.6.32-642.el6.x86_64/build/include" for the kernel "2.6.32-642.el6.x86_64" is valid.  Whoohoo!
2016-05-28T18:21:09.587-07:00| vthread-4| I125: found symbol version file /lib/modules/2.6.32-642.el6.x86_64/build/Module.symvers
2016-05-28T18:21:09.587-07:00| vthread-4| I125: Reading symbol versions from /lib/modules/2.6.32-642.el6.x86_64/build/Module.symvers.
2016-05-28T18:21:09.597-07:00| vthread-4| I125: Read 12201 symbol versions
2016-05-28T18:21:09.597-07:00| vthread-4| I125: Reading in info for the vmmon module.
2016-05-28T18:21:09.597-07:00| vthread-4| I125: Reading in info for the vmnet module.
2016-05-28T18:21:09.597-07:00| vthread-4| I125: Reading in info for the vmblock module.
2016-05-28T18:21:09.597-07:00| vthread-4| I125: Reading in info for the vmci module.
2016-05-28T18:21:09.597-07:00| vthread-4| I125: Reading in info for the vsock module.
2016-05-28T18:21:09.597-07:00| vthread-4| I125: Setting vsock to depend on vmci.
2016-05-28T18:21:09.597-07:00| vthread-4| I125: Invoking modinfo on "vmmon".
2016-05-28T18:21:09.600-07:00| vthread-4| I125: "/sbin/modinfo" exited with status 0.
2016-05-28T18:21:09.600-07:00| vthread-4| I125: Invoking modinfo on "vmnet".
2016-05-28T18:21:09.601-07:00| vthread-4| I125: "/sbin/modinfo" exited with status 256.
2016-05-28T18:21:09.601-07:00| vthread-4| I125: Invoking modinfo on "vmblock".
2016-05-28T18:21:09.603-07:00| vthread-4| I125: "/sbin/modinfo" exited with status 0.
2016-05-28T18:21:09.603-07:00| vthread-4| I125: Invoking modinfo on "vmci".
2016-05-28T18:21:09.605-07:00| vthread-4| I125: "/sbin/modinfo" exited with status 0.
2016-05-28T18:21:09.605-07:00| vthread-4| I125: Invoking modinfo on "vsock".
2016-05-28T18:21:09.607-07:00| vthread-4| I125: "/sbin/modinfo" exited with status 0.
2016-05-28T18:21:09.618-07:00| vthread-4| I125: to be installed: vmnet status: 0
2016-05-28T18:21:09.624-07:00| vthread-4| I125: Obtaining info using the running kernel.
2016-05-28T18:21:09.624-07:00| vthread-4| I125: Setting header path for 2.6.32-642.el6.x86_64 to "/lib/modules/2.6.32-642.el6.x86_64/build/include".
2016-05-28T18:21:09.624-07:00| vthread-4| I125: Validating path "/lib/modules/2.6.32-642.el6.x86_64/build/include" for kernel release "2.6.32-642.el6.x86_64".
2016-05-28T18:21:09.624-07:00| vthread-4| I125: Failed to find /lib/modules/2.6.32-642.el6.x86_64/build/include/generated/utsrelease.h
2016-05-28T18:21:09.624-07:00| vthread-4| I125: using /usr/bin/gcc for preprocess check
2016-05-28T18:21:09.632-07:00| vthread-4| I125: Preprocessed UTS_RELEASE, got value "2.6.32-642.el6.x86_64".
2016-05-28T18:21:09.632-07:00| vthread-4| I125: The header path "/lib/modules/2.6.32-642.el6.x86_64/build/include" for the kernel "2.6.32-642.el6.x86_64" is valid.  Whoohoo!
2016-05-28T18:21:09.701-07:00| vthread-4| I125: found symbol version file /lib/modules/2.6.32-642.el6.x86_64/build/Module.symvers
2016-05-28T18:21:09.702-07:00| vthread-4| I125: Reading symbol versions from /lib/modules/2.6.32-642.el6.x86_64/build/Module.symvers.
2016-05-28T18:21:09.711-07:00| vthread-4| I125: Read 12201 symbol versions
2016-05-28T18:21:09.711-07:00| vthread-4| I125: Kernel header path retrieved from FileEntry: /lib/modules/2.6.32-642.el6.x86_64/build/include
2016-05-28T18:21:09.711-07:00| vthread-4| I125: Update kernel header path to /lib/modules/2.6.32-642.el6.x86_64/build/include
2016-05-28T18:21:09.711-07:00| vthread-4| I125: Validating path "/lib/modules/2.6.32-642.el6.x86_64/build/include" for kernel release "2.6.32-642.el6.x86_64".
2016-05-28T18:21:09.711-07:00| vthread-4| I125: Failed to find /lib/modules/2.6.32-642.el6.x86_64/build/include/generated/utsrelease.h
2016-05-28T18:21:09.711-07:00| vthread-4| I125: using /usr/bin/gcc for preprocess check
2016-05-28T18:21:09.719-07:00| vthread-4| I125: Preprocessed UTS_RELEASE, got value "2.6.32-642.el6.x86_64".
2016-05-28T18:21:09.719-07:00| vthread-4| I125: The header path "/lib/modules/2.6.32-642.el6.x86_64/build/include" for the kernel "2.6.32-642.el6.x86_64" is valid.  Whoohoo!
2016-05-28T18:21:09.720-07:00| vthread-4| I125: Found compiler at "/usr/bin/gcc"
2016-05-28T18:21:09.724-07:00| vthread-4| I125: Got gcc version "4.4.7".
2016-05-28T18:21:09.724-07:00| vthread-4| I125: The GCC version matches the kernel GCC minor version like a glove.
2016-05-28T18:21:09.724-07:00| vthread-4| I125: Using user supplied compiler "/usr/bin/gcc".
2016-05-28T18:21:09.727-07:00| vthread-4| I125: Got gcc version "4.4.7".
2016-05-28T18:21:09.727-07:00| vthread-4| I125: The GCC version matches the kernel GCC minor version like a glove.
2016-05-28T18:21:09.729-07:00| vthread-4| I125: Trying to find a suitable PBM set for kernel "2.6.32-642.el6.x86_64".
2016-05-28T18:21:09.729-07:00| vthread-4| I125: No matching PBM set was found for kernel "2.6.32-642.el6.x86_64".
2016-05-28T18:21:09.729-07:00| vthread-4| I125: The GCC version matches the kernel GCC minor version like a glove.
2016-05-28T18:21:09.729-07:00| vthread-4| I125: Validating path "/lib/modules/2.6.32-642.el6.x86_64/build/include" for kernel release "2.6.32-642.el6.x86_64".
2016-05-28T18:21:09.729-07:00| vthread-4| I125: Failed to find /lib/modules/2.6.32-642.el6.x86_64/build/include/generated/utsrelease.h
2016-05-28T18:21:09.729-07:00| vthread-4| I125: using /usr/bin/gcc for preprocess check
2016-05-28T18:21:09.737-07:00| vthread-4| I125: Preprocessed UTS_RELEASE, got value "2.6.32-642.el6.x86_64".
2016-05-28T18:21:09.737-07:00| vthread-4| I125: The header path "/lib/modules/2.6.32-642.el6.x86_64/build/include" for the kernel "2.6.32-642.el6.x86_64" is valid.  Whoohoo!
2016-05-28T18:21:09.738-07:00| vthread-4| I125: The GCC version matches the kernel GCC minor version like a glove.
2016-05-28T18:21:09.738-07:00| vthread-4| I125: Validating path "/lib/modules/2.6.32-642.el6.x86_64/build/include" for kernel release "2.6.32-642.el6.x86_64".
2016-05-28T18:21:09.738-07:00| vthread-4| I125: Failed to find /lib/modules/2.6.32-642.el6.x86_64/build/include/generated/utsrelease.h
2016-05-28T18:21:09.738-07:00| vthread-4| I125: using /usr/bin/gcc for preprocess check
2016-05-28T18:21:09.746-07:00| vthread-4| I125: Preprocessed UTS_RELEASE, got value "2.6.32-642.el6.x86_64".
2016-05-28T18:21:09.746-07:00| vthread-4| I125: The header path "/lib/modules/2.6.32-642.el6.x86_64/build/include" for the kernel "2.6.32-642.el6.x86_64" is valid.  Whoohoo!
2016-05-28T18:21:09.746-07:00| vthread-4| I125: Using temp dir "/tmp".
2016-05-28T18:21:09.747-07:00| vthread-4| I125: Obtaining info using the running kernel.
2016-05-28T18:21:09.747-07:00| vthread-4| I125: Setting header path for 2.6.32-642.el6.x86_64 to "/lib/modules/2.6.32-642.el6.x86_64/build/include".
2016-05-28T18:21:09.747-07:00| vthread-4| I125: Validating path "/lib/modules/2.6.32-642.el6.x86_64/build/include" for kernel release "2.6.32-642.el6.x86_64".
2016-05-28T18:21:09.747-07:00| vthread-4| I125: Failed to find /lib/modules/2.6.32-642.el6.x86_64/build/include/generated/utsrelease.h
2016-05-28T18:21:09.747-07:00| vthread-4| I125: using /usr/bin/gcc for preprocess check
2016-05-28T18:21:09.755-07:00| vthread-4| I125: Preprocessed UTS_RELEASE, got value "2.6.32-642.el6.x86_64".
2016-05-28T18:21:09.755-07:00| vthread-4| I125: The header path "/lib/modules/2.6.32-642.el6.x86_64/build/include" for the kernel "2.6.32-642.el6.x86_64" is valid.  Whoohoo!
2016-05-28T18:21:09.825-07:00| vthread-4| I125: found symbol version file /lib/modules/2.6.32-642.el6.x86_64/build/Module.symvers
2016-05-28T18:21:09.825-07:00| vthread-4| I125: Reading symbol versions from /lib/modules/2.6.32-642.el6.x86_64/build/Module.symvers.
2016-05-28T18:21:09.834-07:00| vthread-4| I125: Read 12201 symbol versions
2016-05-28T18:21:09.834-07:00| vthread-4| I125: Invoking modinfo on "vmnet".
2016-05-28T18:21:09.836-07:00| vthread-4| I125: "/sbin/modinfo" exited with status 256.
2016-05-28T18:21:10.081-07:00| vthread-4| I125: Setting destination path for vmnet to "/lib/modules/2.6.32-642.el6.x86_64/misc/vmnet.ko".
2016-05-28T18:21:10.081-07:00| vthread-4| I125: Extracting the vmnet source from "/usr/lib/vmware/modules/source/vmnet.tar".
2016-05-28T18:21:10.087-07:00| vthread-4| I125: Successfully extracted the vmnet source.
2016-05-28T18:21:10.087-07:00| vthread-4| I125: Building module with command "/usr/bin/make -j8 -C /tmp/modconfig-tH7bci/vmnet-only auto-build HEADER_DIR=/lib/modules/2.6.32-642.el6.x86_64/build/include CC=/usr/bin/gcc IS_GCC_3=no"
2016-05-28T18:21:11.063-07:00| vthread-4| W115: Failed to build vmnet.  Failed to execute the build command.

    Hi, I faced the same problem, and now I have corrected this issue.

    He was vmnet.ko, at least for me.

    Here's how to solve,

    You can find the latest vmnet.ko of /lib/modules/~previous_kernel_version~/misc/vmnet.ko

    Copy vmnet.ko into your current/lib/modules/your_current_version/misc folder.

    And then run vmware, if you fail at the first, please run again.

    If so, you can run vmwre!

    I hope this will help you.

    Good day.

  • PCI errors - Compaq 6200 Pro small form factor

    I had a major breakdown of the system OP, the new hard drive, the new installation of Win 7 Ultimate... everything works fine, except PCI Serial Port & Simple communications controller PCI in the... Device Manager showing the error

    I went to download drivers page and downloaded and executed every driver available but still have PCI errors...

    Help please & thanks in advance.

    JWalters

    Hello:

    You need this driver... install the driver manually if you need to.

    There are records of pilot for both devices.

    http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5037901&swItemId=vc_138955_1&swEnvOid=4059

  • HP Compaq 6200 Pro SFF: Opgrade Windows 10 - HP Compaq 6200 Pro Small Form Factor PC

    Hello

    I want opgrade Windows 7 Pro (64 bit) to Windows 10 Pro (64-bit) with a clean install.

    I am aware that I have to choose the UEFI mode in the start menu, but do I

    enable/disable in the BIOS before I boot the installation DVD?

    Concerning

    Knud Erik

    Hello sfinksen ;

    Let me welcome you on the HP forums!

    I read your post about upgrading your PC to Win10 and wanted to help.

    First of all, you do not ask UEFI install Win10 Pro 64-bit.  I installed on a desktop computer using BIOS and MBR and it works very well.  You're not even sure that a Mini-PC offers the possibility of UEFI?

    Then, personally, I recommend the update.  The problem, that you are facing is that Microsoft provides only pilots with the most basic features and what you really need for these features in laptops is the specialized drivers written for the specific material found in laptops - and unfortunately, there is no HP Win10 laptop driver.  HP only guarantees the compatibility of Win10 for machines manufactured after August 2013. HP is not no matter what timetable indicating when, or IF, they will produce drivers for older machines.

    To further complicate things, the GoBack to Win10 function has been proven to be unreliable, so when people are trying to return to an earlier OS when it does not work, cannot leave the machine in a damaged condition, such as only a full factory reset HP recovery support it will get back to a working condition , and not only you have to buy only media, you end up losing all your data, settings, and applications in the process.

    However, you can protect yourself from this kind of problems if, BEFORE you do that, you consider using a third-party application Imaging/restoration as Macrium Reflect to image your machine off, so you can easily restore it if something does not work.  And don't count on the Win10 GoBack function back on Win7, it is not reliable and can leave your computer in a damaged state.

    Macrium reflect (MR) provides a FREE version that can be used to image and restore partitions or drives together.

    What I recommend is the following:
    (1) download and install Macrium reflect (MR)
    (2) run M. and choose the option: "Create an image of the partition (s) required to backup and restore Windows" to write a full backup to an external drive or USB key
    (3) use the option to create a CD or a USB startup key

    I use all the time and it usually takes less than 10 minutes to make the backup of the image and at the same time or less do a restore.  In addition, MR has the ability to add a recovery Boot Menu entry.  This then allows you to boot into Windows re, and then you can use it to do a restore - when you cannot start Windows!

    NOW, you have the means to restore a full system that works for the external hard drive or USB key in a few minutes.

    In addition, a clean install of Win10 lights only in the following circumstances:

    1) using build 10240 (RTM), an upgrade in previous place was done and confirmed have activated.

    (2) using the updated 10586 (November), a valid before the OS product key has been entered.

    So, if you have decided to do a clean install, you'd better using the MS Media (MCT) tool: Windows Installer by using the tool of creation of media - 10 Windows help

    With this tool, you have the option of (1) creation of installation of Win10 (USB or DVD) media, (2) download an ISO file, (3) update the PC directly.  If all you want to do is updated on this PC, then choose the option: upgrade this PC now.  This tool automatically selects the generation 10586 - giving you the opportunity to enter a product key to activate it.

    Good luck

    I'm a volunteer and I do not work for, or represent, HP.
    ========================================================================
    If you feel that my suggestions helped you, please click on the thumbs-up symbol to say thank you!

    If they helped to solve your problem, please click 'Accept as Solution' to help others find similar information.

  • HP COMPAQ 6200 PRO SFF PC: Bus PCI 0, device 31, function 3 DRIVER

    I HAVE A PC HP COMPAQ 6200 PRO SMALL FORM FACTOR I KEEP GETTING MESSAGE ' CAN FIND DRIVER FOR CONTROLLER of BUS SM THE DRIVER IS: PCI bus 0, device 31, function 3 WHERE CAN GET THIS DRIVER? Thank you

    Hello:

    Download, unzip and run the file setup.exe from the link below... then reboot the PC.

    https://Downloadcenter.Intel.com/download/20018/INF-Update-utility-primarily-for-Intel-6-5-4-3-900-series-chipsets-zip-format?product=1145

  • Compaq 6200 Pro - serial port PCI does not

    Hello

    I have a problem with installing the correct drivers for HP Compaq PC 6200 Pro Small Form Factor,

    I can't get PCI serial port to work on Win XP...

    I tried all the official drivers on the HP support site.

    The PC came with pre installed Windows 7, so I'm downgrading to Win XP.



    Hello:

    It's like I initially thought... the AMT driver.

    Apparently, you have to manually install by clicking on the device in Device Manager, click on the driver tab, click on set to update driver. Select the driver manually search in a specific location, and then go to C:\ SWSETUP\sp52247 and install the drivers for this folder.

    Please read this post where I helped someone with a similar machine (the 6200 is a smaller version of the 8200) in the forum of business support. He could not get the driver to install by running the file. He had to install it manually, and it worked for him. So, it should work for you too.

    http://h30499.www3.HP.com/T5/business-PCs-Deskpro-Evo/8200-elite-PCI-serial-port-driver/TD-p/4835455

    You can use the drivers that I posted in the link above if you want to, but I think that they are the same.

    Paul

  • Compaq 6200 PRO MT: Makes the computer does not start after upgrade CPU

    I have the HP Compaq 6200 PRO PC of MT 615114-001 motherboard and processor Intel Celeron CPU (LGA 1155). After I changed the CPU for Intel Core i5 (LGA 1155) computer does not start. He begins a minute (less than one second) and stops again. No beeps. After you have installed the Celeron back everything works fine. i5 CPU is brand new. What can be?

    In my previous post, I explained the reason it has not worked, and listed the CPU that will work.

    HP tests CPU in the laboratory and publishes a list of processors that will work in a notebook.

    Notebook motherboard BIOS has a list of processors that will work. If it is installed, which is not encoded as OK in the BIOS ROM file, then this will not work.

    Processors published (in the maintenance guide & Service for your nttebook series model) are available in models that can be deilvered in State CTO (configured to order).

  • Memory RAM replacement hp compaq 6200 pro sff

    I have hp compaq 6200 pro SFF, now has only 2 GB of RAM memory and I want to add more to it. where can I find what I need? I have a couple of old computers here, but need to know if I can use these memoirs RAM for this computer. I can't find it.

    Hello:

    Here is the link to the quickspecs for your model...

    http://WWW8.HP.com/h20195/v2/GetDocument.aspx?DocName=c04123261

    Info upgrade memory are on page 7.

    Note that you can install 4 x 8 GB PC3-10600 memory, even if the configuration table only 4 x 4 GB.

  • HP compaq 6200 pro sff: drivers missing

    good day to all,

    help with the following missing drivers.

    controller Ethernet (hardware id);

    PCI\VEN_8086 & Dev_1502 & SUBSYS_1497 / 03C & REV_04

    Pci\Ven_8086 & Dev_1502 & SUBSYS_1497103C

    Pci\Ven_8086 & Dev_1502 & CC_020000

    Pci\Ven_8086 & Dev_1502 & CC_0200

    In addition,

    PCI simple communication controller

    SM bus controller

    PCI serial port.

    The PC is HP compaq 6200 pro sff

    Windows 7 pro 64-bit.

    Thank you.

    Hello:

    You need these drivers...

    SMBus:

    http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5037910 & swItemId = vc_88640_1 & swEnvOid = 4059

    Simple PCI and PCI Serial Port:

    http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5037910 & swItemId = vc_138955_1 & swEnvOid = 4059

    Ethernet:

    http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5037910 & swItemId = vc_108131_1 & swEnvOid = 4059 #tab1

  • Invalid electronic serial number after swapping out motherboard, HP Compaq 6200 Pro SFF

    Hello

    I have just replaced a motherboard under warranty and I try to find the utility to change S/N in the BIOS, have obtained a location for the equivalent laptop but can't find the PC version using a USB.

    I have CSN access, but cannot find the utility appropriate to effect the change.

    PC is:

    HP Compaq 6200 Pro SFF

    Any help would be appreciated.

    Thank you

    Darren

    [Personal information]

    Hello:

    Here's what you need to do... This model has no need to inventory number or serial number change utility...

    After entering the Setup by pressing the F10 key, press on Ctrl + A to open additional fields in the security > system menu IDs.

    Enter the serial number of your PC inventory and serial number of chassis number.

    Save the changes then and once when you exit the BIOS.

    Paul

  • HP Compaq 6200 Pro MT PC: Error number SN

    Hello.

    I just replaced a motherboard on an HP PC Compaq 6200 Pro MT.

    The issue is that, once replaced it get an error "invalid electronic serial number".

    I tried the game that in the BIOS, but there is no other choice.

    I am aware that there is a DMI tool for laptop to set these parameters, is there one for the PC?

    Concerning

    Tyzer

    Engineer of the ASP.

    Hi, Tyzer:

    See if it works...

    After entering the Setup by pressing the F10 key, press on Ctrl + A to open additional fields in the security > system menu IDs.

    Enter the serial number of your PC inventory and serial number of chassis number.

    Save the changes then and once when you exit the BIOS.

    Paul

  • have the new Canon pro-1000. Just installed the inks. He tells me that I'm not on a flat surface and c

    I have the new Canon pro-1000. Just installed the inks. He tells me that I'm not on a surface level code1340 error '. Impossible to go to the next step,

    No post?

    Ian

Maybe you are looking for

  • Satellite Pro 440 CDT does not supply power to the top

    Hi, I have an old 440 CDT which does not supply power to the top. Someone at - it ideas?AC is connected, the power led is lit, green. Battery is dead (as in buried). When I press the power button, the following occurs:-The led is green-Num lock (the

  • freeupharddrivespace

    training main c is almost out of space and I am not sure what to remove. and will not let me delete programs than unnessary. try to remove it and he said: we can not do. and I can't do on fly records management without permission and I do not know ho

  • Game online, Rift requires DirectX9 be installed, but get error internal system for DirectX9

    I recently bought the video game Rift via online download, and at the end of my installation it says "Your DirectX9 must be updated," I proceeded, agreed to the terms in the DirectX Wizard and was brought to a page that says "Installation: initializi

  • "You have no preferred wireless networks.

    Hello I installed Build 7100 and have been finding problems in all directions. Is it the right place to report issues? The dev team will never receive any comments posted here? I have a specific problem that is driving me crazy and if it is not sorte

  • How do reset you the program back to Windows 7 compatibility mode?

    I tried to get a program runs on Windows 7, but it would freeze upwards.  Then I changed a setting in the program compatibility, try a Windows XP mode and a mode of Windows Vista (without success).  How to get out the compatibility settings and just