HP COMPAQ 6200 PRO SFF PC: Bus PCI 0, device 31, function 3 DRIVER

Similar Questions

• HP compaq 6200 pro sff: drivers missing

  good day to all,

  help with the following missing drivers.

  controller Ethernet (hardware id);

  PCI\VEN_8086 & Dev_1502 & SUBSYS_1497 / 03C & REV_04

  Pci\Ven_8086 & Dev_1502 & SUBSYS_1497103C

  Pci\Ven_8086 & Dev_1502 & CC_020000

  Pci\Ven_8086 & Dev_1502 & CC_0200

  In addition,

  PCI simple communication controller

  SM bus controller

  PCI serial port.

  The PC is HP compaq 6200 pro sff

  Windows 7 pro 64-bit.

  Thank you.

  Hello:

  You need these drivers...

  SMBus:

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5037910 & swItemId = vc_88640_1 & swEnvOid = 4059

  Simple PCI and PCI Serial Port:

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5037910 & swItemId = vc_138955_1 & swEnvOid = 4059

  Ethernet:

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5037910 & swItemId = vc_108131_1 & swEnvOid = 4059 #tab1

• Memory RAM replacement hp compaq 6200 pro sff

  I have hp compaq 6200 pro SFF, now has only 2 GB of RAM memory and I want to add more to it. where can I find what I need? I have a couple of old computers here, but need to know if I can use these memoirs RAM for this computer. I can't find it.

  Hello:

  Here is the link to the quickspecs for your model...

  http://WWW8.HP.com/h20195/v2/GetDocument.aspx?DocName=c04123261

  Info upgrade memory are on page 7.

  Note that you can install 4 x 8 GB PC3-10600 memory, even if the configuration table only 4 x 4 GB.

• Invalid electronic serial number after swapping out motherboard, HP Compaq 6200 Pro SFF

  Hello

  I have just replaced a motherboard under warranty and I try to find the utility to change S/N in the BIOS, have obtained a location for the equivalent laptop but can't find the PC version using a USB.

  I have CSN access, but cannot find the utility appropriate to effect the change.

  PC is:

  HP Compaq 6200 Pro SFF

  Any help would be appreciated.

  Thank you

  Darren

  [Personal information]

  Hello:

  Here's what you need to do... This model has no need to inventory number or serial number change utility...

  After entering the Setup by pressing the F10 key, press on Ctrl + A to open additional fields in the security > system menu IDs.

  Enter the serial number of your PC inventory and serial number of chassis number.

  Save the changes then and once when you exit the BIOS.

  Paul

• HP Envy 17-3077NR - bus PCI 10, device 0, function 0 (Code 28)

  Greetings!

  Hey, I have a HP Envy 17-3077NR, installed a cost of Windows 7, I'm sure that I installed all drivers 64-bit HP drivers page, yet "PCI Device" is always on view under "Other devices" with yellow exclamation point. I checked the properties and it says ' bus PCI 10, device 0, function 0 (Code 28). Nothing helps, I have re-installed Realtek Card Reader, Ethernet and Bluetooth. Please help as I am setting up this device for someone else and you want to do things.

  Thanks in advance!

  Hello

  You are welcome

  The hardware id is for the Realtek card reader driver, so I suggest to try to reinstall it from the link below.

  http://ftp.HP.com/pub/SoftPaq/sp56501-57000/sp56908.exe

  Once completed, restart the laptop.

  When windows has reloaded, check device manager again.

  Best regards

  DP - K

• HP Compaq 6200 Pro SFF: Latch door stuck on 6200/6300 Pro SFF

  I don't know what my users to my machines, but I received (especially 6200/6300 Pro SFF) computers that I can't open the latch to release for the sidebar being stuck. When I pull the latch, the rear of the frame folds inward and the latch will not release. Someone has any advice on how to unlock these?

  The best answer I got from another forum is to shoot the main part of the case (pliers with tapered beak hanging in the locking ring got me the best results) while lifting simultaneously the release handle on the side panel. Not 100% effective, but he did unlock about 90% of my problem machines.

• HP Compaq 6200 Pro SFF: Opgrade Windows 10 - HP Compaq 6200 Pro Small Form Factor PC

  Hello

  I want opgrade Windows 7 Pro (64 bit) to Windows 10 Pro (64-bit) with a clean install.

  I am aware that I have to choose the UEFI mode in the start menu, but do I

  enable/disable in the BIOS before I boot the installation DVD?

  Concerning

  Knud Erik

  Hello sfinksen ;
  
  Let me welcome you on the HP forums!
  
  I read your post about upgrading your PC to Win10 and wanted to help.
  
  First of all, you do not ask UEFI install Win10 Pro 64-bit.  I installed on a desktop computer using BIOS and MBR and it works very well.  You're not even sure that a Mini-PC offers the possibility of UEFI?

  Then, personally, I recommend the update.  The problem, that you are facing is that Microsoft provides only pilots with the most basic features and what you really need for these features in laptops is the specialized drivers written for the specific material found in laptops - and unfortunately, there is no HP Win10 laptop driver.  HP only guarantees the compatibility of Win10 for machines manufactured after August 2013. HP is not no matter what timetable indicating when, or IF, they will produce drivers for older machines.

  To further complicate things, the GoBack to Win10 function has been proven to be unreliable, so when people are trying to return to an earlier OS when it does not work, cannot leave the machine in a damaged condition, such as only a full factory reset HP recovery support it will get back to a working condition , and not only you have to buy only media, you end up losing all your data, settings, and applications in the process.
  
  However, you can protect yourself from this kind of problems if, BEFORE you do that, you consider using a third-party application Imaging/restoration as Macrium Reflect to image your machine off, so you can easily restore it if something does not work.  And don't count on the Win10 GoBack function back on Win7, it is not reliable and can leave your computer in a damaged state.
  
  Macrium reflect (MR) provides a FREE version that can be used to image and restore partitions or drives together.
  
  What I recommend is the following:
  (1) download and install Macrium reflect (MR)
  (2) run M. and choose the option: "Create an image of the partition (s) required to backup and restore Windows" to write a full backup to an external drive or USB key
  (3) use the option to create a CD or a USB startup key
  
  I use all the time and it usually takes less than 10 minutes to make the backup of the image and at the same time or less do a restore.  In addition, MR has the ability to add a recovery Boot Menu entry.  This then allows you to boot into Windows re, and then you can use it to do a restore - when you cannot start Windows!
  
  NOW, you have the means to restore a full system that works for the external hard drive or USB key in a few minutes.

  In addition, a clean install of Win10 lights only in the following circumstances:

  1) using build 10240 (RTM), an upgrade in previous place was done and confirmed have activated.

  (2) using the updated 10586 (November), a valid before the OS product key has been entered.

  So, if you have decided to do a clean install, you'd better using the MS Media (MCT) tool: Windows Installer by using the tool of creation of media - 10 Windows help

  With this tool, you have the option of (1) creation of installation of Win10 (USB or DVD) media, (2) download an ISO file, (3) update the PC directly.  If all you want to do is updated on this PC, then choose the option: upgrade this PC now.  This tool automatically selects the generation 10586 - giving you the opportunity to enter a product key to activate it.

  Good luck

  I'm a volunteer and I do not work for, or represent, HP.
  ========================================================================
  If you feel that my suggestions helped you, please click on the thumbs-up symbol to say thank you!
  
  If they helped to solve your problem, please click 'Accept as Solution' to help others find similar information.

• HP Compaq 6200 pro sff: HP Compaq 6200 pro

  Hello

  My hard drive died last week so I tried to install a new Western Digital drive, but when I start the pc it shows the HP logo screen, then I get a blank screen with a corsor in the upper left (solid cursor does not blink). The pc does not go further.

  I'm sure that it is a bios issue but do not know what, any help would be appreciated.

  James

  Hello

  Did you check if all cables are connected firmly in their place and if the RAM is very savvy. It is possible that you dislodged something during the installation of the new HARD drive. Also, what model is the new HARD disk? How exactly does your previous PC is dead? Have you tried swapping SATA cables?

  Hope that helps.

• 6200 pro sff: hp compaq 6200 pro sff was not able to start, but the fan will operate at excessive speed

  PC shuts off during the night. Haven't turned on this morning, white screen, no boot fan, cpu and power begins to operate at high speed after about 60 seconds. No beeps or flashing power light. Substituted know good power supply, same result. Removed RAM, no beeps from the bios of this.

  Hello

  Try to start without CPU.

  If the problem persists, no beeps, you will need to replace the system board.

  If it beeps (3) without CPU, you will need to replace the motherboard and test the CPU on another unit.

  Computer science is not an exact science , the most obvious is that it's only the system board but if you test the CPU you will be 100% safe.

  Concerning

• Bus PCI 5, device 9, function 3

  I recently updated my card wireless, hard drive and RAM, but even after installing the drivers, it indicates that there are drivers missing.

  Base system device PCI VEN_1180 & DEV_0843 & SUBSYS_30B5103C & REV_01\4 & 3A3249AB & 0 & 4 to 80 that the drivers for this device are not installed.
  Base system device PCI VEN_1180 & DEV_0592 & SUBSYS_30B5103C & REV_0A\4 & 3A3249AB & 0 & 4B 80 that the drivers for this device are not installed.
  Coprocessor PCI\VEN_10DE & DEV_0271 & SUBSYS_30B5103C & REV_A3\3 & 13C0B0C5 & 0 & 53 that the drivers for this device are not installed.

  (These codes are found under the information system, but not in "Other devices")

  Im running on a hp Pavilion dv2000, could you guide me for these specific drivers so I left the 'warning' annoying error... ? Thank you advance.

  Hello:

  You need these drivers...

  Coprocessor:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-46259-1&cc=us&DLC=en&LC=en&OS=2093&product=3177437&sw_lang=

  X 2 base system device:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-46445-1&cc=us&DLC=en&LC=en&OS=2093&product=3177437&sw_lang=

• Bus PCI 5, device 0, function 0

  network controller its lack

  Hello Joe,

  Thanks for posting your question on the Microsoft community.

  We need more information about the issue so that we can help you better.

  What is the brand and model of your computer?

  Thank you for details on the issue.

  This problem may occur if the network driver is missing or not installed.

  I suggest you update to the computer manufacturer's Web site network driver and check the issue.
  Reference:
  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-us/Windows/Update-driver-hardware-ISN

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• HP Compaq 6200 Pro small format: Re-install the network adapter

  Dear assistants & members,

  Yesterday, I tried to download a 64-bit system that has not worked and had trouble.

  I am trying to connect to the internet, but it still says: a network adapter was not found (something like that)

  I have seen a lot of messages so I already do my hardware ID:

  PCI\VEN_8086 & DEV_1502 & SUBSYS_1497103C & REV_04

  PCI\VEN_8086 & DEV_1502 & SUBSYS_1497103C

  PCI\VEN_8086 & DEV_1502 & CC_020000

  PCI\VEN_8086 & DEV_1502 & CC_0200

  I hope you self-introduction can help out me.

  I'm computer: HP Compaq 6200 Pro Small Form Factor

  Hello:

  Try the driver directly from Intel.  The hardware ID you posted is for an Intel ethernet card.

  The first file listed is for W7 32 bit.

  https://Downloadcenter.Intel.com/download/18713/network-adapter-driver-for-Windows-7-

  I was going to ask...

  How did you couldn't get W7 x 64 install?

  I have an Elite 8200, which is the same model as yours, except that it's a chipset series 6 Intel a little better than you do.

  I had no problem installing W7 x 64 on it.

• HP Compaq 6000 Pro SFF: Help change the chassis.

  Nice day.

  I have a HP Compaq 6000 Pro SFF PC, I want to upgrade in a mini tower, is it possible with this PC? The reason is because I want to install a new GFX card and a cooling system for best performance, however, @ 240 PSU will be not reduced, especially not when I already 2 SATA drives. Can someone tell me please on what to do? Thanks in advance.

  PS: My PC is already out of warranty 3 months ago. If I can do pretty much anything I want with it without breach of the warranty.

  Specifications of the PC:

  HP Compaq 6000 Pro SFF

  Intel Core 2 Duo E7500 2.93 Ghz

  1 x DDR3 2 G of Ram

  2 x SATA hard drives

  1 x DVD player

  Windows 7 SP1 (32-bit)

  1 x PCI-E slot? (I do not currently know what type of housing is)

  POWER SUPPLY 240

  The motherboard so that the PC is listed as a BTX.  The typical motherboard is ATX.  HERE IS a PAGE that gives information of the two styles differences.  What I see, the BTX is built around designs of air traffic, so be careful.

• 6200 pro sff: 6200 pro sff and Radeon HD5450 works and I have to change the jumpers

  got myself a 6200 hp pro sff and have upgraded to win 10 and want to add pci card hdmi thought it would be a simplendrop in and go but not any quick tips to make work that I have to put a few riders in here

  Hello:

  A HD 5450 should have works great.

  The HD 6450 was the graphics card optionally available on the 6200 Pro SFF.

  There are no jumpers or BIOS settings to change.

  The card should have been automatically picked up by the BIOS, and it should have disabled the onboard video.

  What happens when you turn on the PC?

  It works and you don't have a video?

  If so, all you need to do is to remove the card, re - turning on the PC, uninstall the Intel HD graphics card and driver, turn off the PC and install the new video card.

  To uninstall the graphics card, go to Device Manager, click to expand the category of device adapter screen, right-click on the Intel HD graphics card, select uninstall and check the box uninstall driver.

  If this does not resolve the issue, most likely the card you purchased has a problem.

  Return it and get a HD 6450 low profile card.

• HP Compaq 6200 Pro small-format: How can I tell how old my computer is by serial number

  I would like to know how old my computer with the help of its serial number.

  HP Compaq 6200 Pro Small Form Factor PC

  Serial number: [personal information]

  I hope someone can tell me when my model was in production and sometimes identify the date that your machine was completed.

  Thanks in advance.

  Best,

  Renata

  Rena.

  Your computer was born.

  Week 07

  February 13, 2012

  19 February 2012

  Year 2012 week 07

  REO