HP Compaq 8300 Elite USDT: Max Wattage on HP 8300 USDT MXM slot

Similar Questions

• HP Compaq 8100 Elite: Video unrecognized card in PCI-Express x 16 slot for security

  I disable the PCI Express connector in the computer - security - Slot Configuration on BIOS.

  I don't know that my card on Board did not work and now machine does not start, machine beeps 6 times (error video card).

  I can't access the bios.

  I try to reset the CMOS, remove the Green rider, remove CMOS battery, press the button within 10 seconds, press the power button (to remove rest of energy.

  But none of it works.

  Can someone help me?

  How can I reactivate PCI Express x 16?

  Hello:

  If your integrated graphics card does not work, and reset the CMOS does not work, you can try putting the PCI express x 16 video card, you now have in the location PCIe White x 4 slot (slot next to the slot PCIe x 16 black white video card) and see if you can get into the BIOS to change the PCI x 16 setting.  It might work in the x 4 slot.

  If it does not, you will need to install a video card PCI (the one that goes in one of the white PCI slots) and use it to get into the BIOS, so you can change the settings to enable the location of PCIe x 16.

  So see if you can find a cheap, used, video card PCI on eBay, and should allow you to have the video again.

  You should also make sure you have removed all the connections of the computer when you reset the CMOS (all cables, power supply, mouse, monitor, etc.).

• Compaq 8000 Elite COnvertible: compaq 8000 elite minitour convertible pci driver windows 7

  Hello, I had trouble finding the right drivers for my port of compaq 8000 elite series minitour convertible pci and pci simple communication controller, running windows 7 ultimate 64-bit...

  I found a link in a different thread, but the link does not work...

  Could someone help me please? It would be greatly appreciated☻

  Kind regards

  David

  Hello:

  You need these drivers for devices...

  Simple Comms:

  This package contains the device driver Intel Active Client Manager Host Embedded Controller Interface (HECI) for desktop models and operating systems supported.

  FTP://ftp.HP.com/pub/SoftPaq/sp45001-45500/sp45411.exe

  Serial port:

  This package contains the Intel Local Management Service (LMS) and the support of Serial - over - LAN (SOL) for Intel Active Management Technology (AMT) for the supported desktop models and operating systems. This software is part of the Intel Digital Office Initiative.

  FTP://ftp.HP.com/pub/SoftPaq/sp45001-45500/sp45367.exe

• HP Compaq 8000 Elite power supply upgarde

  I have a HP Compaq 8000 Elite 2010 and you must update the power to launch my new Radeon HD 6850 graphics card. After much research I found that this particular computer motherboard does not have a normal diet of 20 or 24 pins but use instead of 2 separate connections from 4 pins for power supply PWR and PWRCPU and a third cable that seems to me to be an ancient and obsolete 6-pin auxiliary power (http://www.playtool.com/pages/psuconnectors/connectors.html#aux) for the PWRCMD supply Cable. I also found that all power is carried out through the motherboard for each piece of hardware in the computer and therefor, most likely has a limit for the maximum possible power supply. Y at - it sort of a power supply that will fit both into the slot in the power supply (which is not the standard size of power supply, but rather measures approximately 6 "x 5.75" x 3.75") and will also be able to connect to and sufficient power to the motherboard? Or am I stuck with an ugly 320W? Help, please!

  Service card: (http://bizsupport1.austin.hp.com/bc/docs/support/SupportManual/c01944841/c01944841.pdf)

  Similar cases: (http://h30434.www3.hp.com/t5/Desktop-Hardware/replacing-PSU-on-HP-COMPAQ-8000-ELITE-Convertible-Mini... )

  Maverickv2,

  You will not be able to upgrade this power supply, model # 508154-001. It is not possible with these connectors. The most absurd part is that the material (disks) are actually powered off the coast of the motherboard. (As you said).

• PC HP Compaq 8100 Elite: How can I add to my PC HP Compaq 8100 Elite HDMI output

  I would like to use my PIP (picture in picture) of HD television feature newly acquired as a monitor for my PC HP Compaq 8100 Elite, which has no HDMI output. The PIP function requires a HDMI input.

  Is there a map update I can add to the PC HP Compaq 8100 Elite to provide me with HDMI?

  At any time.

  I am pleased to have been of assistance.

  There should be a driver disc in the box.

• PC HP Compaq 8200 Elite MT: Should I roll back before flashing the BIOS?

  Hello, I am trying to determine if the update of the BIOS shown on your website is right for my machine: HP Compaq 8200 Elite MT PC. After selecting 'Let HP find my products,' he identified my machine and sent me to a page that asked me to 'Select language driver and OS' two squares. I selected my language, then going on to the next box that asked me to choose my operating system. However, it does include all the Windows 10 selections. I used to have initially Windows 7 Professional. However, I've recently upgraded to Windows Professional 10. Is it safe select the operating system Windows 7 Professional, even if I is no longer on the machine? You see, I want to update BIOS, because I'm having trouble starting after I install memory upgrades, and the provider of the RAM is recommended to upgrade to the latest version of BIOS upgrade before installing the upgrade of RAM, to eliminate these problems. I don't want to make a mistake, and then select the wrong BIOS update. There is an update of the BIOS on HP.com for my MoBo machine, but only for Windows 7 Pro. So should I go back to 7 Pro, before the update?  Please, inform me as to what I should do.

  Hello:

  I just got the flash drive, I use to update BIOS on my HP business desktop PC.

  I plugged in my dc7800 CMT W10 also running.

  The window on the flash drive, and I closed it.

  Then I went on the desktop, click on this PC, click with the right button on the flash drive, which is drive E:\ in my case.

  Then I chose the Format from the menu, and a box will open.

  In the file system drop-down list that I get on my USB flash drive, I get the following options:

  FAT (by default) which is what you want to use.

  NTFS

  FAT32

  exFAT

  So if you don't see these options, try another flash drive.

• PC HP Compaq 8200 Elite CMT: Replacement of the SSD HARD drive and Recovery Options

  I have a PC HP Compaq 8200 Elite CMT I went recently to drive HARD original for one SSD of 850 Evo from Samsung using Samsungs cloning/copying software. Everything went well and the PC is in use today. I do not see the partition D: Recovery on this machine more well, so I think this has not copied or was lost. I still have the disk that was replaced.

  I was wondering if there is a way to replace HARD drive like this with an SSD and everything by keeping the system recovery feature that was on the HARD disk, and if a set of system recovery disks of before installing SSD would continue to operate, or if I need to create new ones, and if I CAN create new ones.

  rgoodrich

  I did what you want to do (for example, to replace a disk with a DDI) and was able to retain the function of HP recovery - but it's because of two important facts.

  First of all, I used a DDI with the same capacity as the original HARD disk.  This is important because if you use a smaller SDS, the HP recovery feature will no more work as a reset begins with reformatting the drive and recreate the original scores - which will fail if the disc is too small.

  Second, I use Macrium Reflect product to 'clone' the HDD to the DDI, which means, he made an exact copy of the partitions on disk on the SDS.  So, when I swapped drives, the PC restarted without any problem.

  People have posted here on the use of the software from Samsung, and they seem to have problems restarting after use and (apparently) with successful copy from disk HARD original in the new SDS.

• Card wireless for Compaq 8000 Elite CMT PC

  I bought a PC given to nine Compaq 8000 Elite CMT. It has Ethernet connectivity, but not wireless I can say. It has 4 slots for pci (?) cards. (Sorry I am a newbie) Is this compatible tower with a wireless card and if so which one should I buy? Thank you very much!

  Hello:

  I would just get an external usb wireless adapter.  No muss. No fuss.

  If you are determined to buy into the internal card, one made for your model.

  http://www.Amazon.com/HP-FH971AA-wireless-PCIe-card/DP/B001GV2320

  HP features on the map...

  http://h30094.www3.HP.com/product.aspx?SKU=3884872

  I launches wireless adapters external USB to dual band on my HP dc7800 CMT, 8000 Elite CMT and 8200 Elite CMT.

• HP Compaq 8200 Elite - XL510AV: need help to find the form factor small PCI Ethernet card

  Hi guys, I hope one of you can help me with this. I need a card PCI Ethernet single port for a HP Compaq 8200 Elite Small Form Factor computer.

  From what I see, the motherboard has a PCIe and two PCI card slots.

  Computer model is XL510AV

  Any help is appreciated.

  Hello

  The following can help:

  http://www.StarTech.com/au/networking-IO/adapter-cards/10100-1000-Mbps-32-bit-PCI-Gigabit-Ethernet-card~ST1000BT32

  It has 2 brackets for standard and one for the low profile, you can swap around.

  Kind regards.

• HP Compaq 8000 Elite SFF: Some HP Windows Media Center buttons on the remote control does not

  I have a desktop PC HP Compaq 8000 Elite SFF that I use as a home theater PC.  I'm under Windows Media Center with 2 cards tuner and antennae of the OTA.

  With this configuration, I use a HP Remote WMC.  The model No. inside the cover of the remote control battery is TSGH-IR01.  The issue I'm having with the remote control that is stationary and move forward and "back" button do nothing when you press.  The light at the top of the remote control flashes when you press those buttons, so I don't think that the buttons themselves infrared are failing.  All the other buttons on the remote work fine.

  I wonder if it is a problem of programming/software and if so, what should I do to solve this problem.   It's annoying to not be able to stop a recorded program is playing when you press the stop button, but having to use a mouse to do it instead.   Any help that can be given will be very appreciated!

  PainedByTech wrote:
  

  I have a desktop PC HP Compaq 8000 Elite SFF that I use as a home theater PC.  I'm under Windows Media Center with 2 cards tuner and antennae of the OTA.

  With this configuration, I use a HP Remote WMC.  The model No. inside the cover of the remote control battery is TSGH-IR01.  The issue I'm having with the remote control that is stationary and move forward and "back" button do nothing when you press.  The light at the top of the remote control flashes when you press those buttons, so I don't think that the buttons themselves infrared are failing.  All the other buttons on the remote work fine.

  I wonder if it is a problem of programming/software and if so, what should I do to solve this problem.   It's annoying to not be able to stop a recorded program is playing when you press the stop button, but having to use a mouse to do it instead.   Any help that can be given will be very appreciated!

  For anyone having this problem, I discovered the cause after reading a post on the forums of thegreenbutton.tv.  An application in Chrome or any browser Chrome (in my case, the Slimjet browser) is the culprit.

  For me, it was the Plex app.  He was diverting the judgment and move forward and back buttons on my remote HP WMC.  As soon as I disabled the application of Plex, the buttons started working.   Never would have guessed that this was the problem!  Hope this helps someone else who might have the same problem.  Ah, tech.  Isn't beautiful?

• HP compaq 8200 elite SFF graphic settings

  I have HP compaq 8200 elite SFF and only intel dedicated hd graphics 2000 which says that I have only 32 MB of ram, how do I increase it? I tried to get into the BIOS but I can't change it whatever it is, not even overclock my processor, is there a solution?
  
  P.S. I tried the bios update from 2.06 to 2.60 and I don't see any changes.

  Hello

  You can get assistance on the HP Enterprise Business Forum.

• HP Compaq Elite 8200 SFF: flickering of screen hp compaq 8200 Elite freeze in windows 10

  HP Compaq 8200 Elite SFF correctly upgraded to 10 professional 64-bit windows, after a week, the monitor flashed for 1-2 seconds, then feezes PC, I have to reboot the PC to get the pc has started, it happens a few times, when pc rebooted PC and os works well? is this sign of incompatibility hardware or software or settings with HP graphics card? This happens not when the pc is Windows 7 Profesional, any help appreciated.

  Personally, I would keep this option unchecked to mitigate with computer after the flicker of the screen reproduce more. I understand that these services are redundant and unnecessary as a result of an upgrade to windows 10 from a previous version of Windows (ie. 7/8/8.1). I hope this helps.

• HP COMPAQ 8200 Elite Micro Tow: Can you tell if this system has slots for SSD or hdd adapter necessary - & gt; SSD?

  Can you tell if this system has slots for SSD or hdd-> ssd adapter need?

  WIN INITIAL 7pro

  i5-4-core - 16GB - RAM - fresh install [new 1 TB HDD] 8.1pro win 10pro Win

  HP COMPAQ 8200 Elite Micro Tower

  P / N:XY139EA #AB7

  PURCHASED 07/03/2012

  For w10pro c: / recommend reinstall to ssd or migrate ssd or even is...?

  SSDS all have sons the same size and holes threaded on the bottom and sides.  They all use the same fine metric threads live short (short, so they don't lower).  These screws must come with the adapter, and I live in general using the lateral holes.  Parts of the adapter have threaded, 3 holes and you will use the back ahead and away from those for channels of the drive Bay.  If you look at each side of a standard 3.5 "HDD, you will see the same same spacing holes.

  Some jobs need the SSD to shift to the left so the orientation of the SSD SATA power and data ports match exactly where they would be if the current drive was a 3.5 "HARD drive clutter.  An example is the drive in a Z620 of drawers which accept 3.5 form factor devices "and slides of drawers in the deep part of the case and automatically mesh with ports of power/data SATA back inside.

  Jobs that fuel just a loose cable and the data cable for the SSD is really doesn't matter much if the SSD is an adapter which keeps it more centered or offset to the left.  I've seen cases where a disk HARD 3.5 "given in the lower Bay and a centered SSD is in the upper drive Bay and there was nearly not enough cable length to reach easily shifted left for drives staggered in the Center.  You can see in the photo below that the Garland of feeding on the HARD drive has two unused SATA power below connectors, and there is not a lot of room between them.

  The card you chose seems good... solid metal.  For the HP 8200 Elite CMT I have access to screws 4 total special 6-32 UNC silver HP threaded screw threaded back ahead and away from the screw holes on both sides of the adapter, and then you use the extraordinary end threads metric short screws mentioned above to fix the SSD to the adapter, as shown in the pictures of Amazon.  These HP silver screw 6-32 no metric I'm talking using Torx or flat screwdriver and their leaders are trained to slip into the channels of the drive Bay.

  There are also other designs which are designed specifically for some HP workstations that include mounts insulation rubber with the sliding mechanism.  I don't think you have that... Here is a picture of eBay one of the 8200 Desktop Elite CMT demonstrating the existence of space on the left for 8 of these silver screw to store, which 4 are missing and used on 3.5 "single drive, you see there.  Don't throw those... they are not something, you can go to Ace hardware and buy.

  

• HP Compaq 8200 Elite Ultra Ethernet slim problem

  Hello.

  I have a HP Compaq 8200 Elite Ultra Slim PC running windows 7 Home Premium 64-bit. I did a fresh install of windows with all the drivers and software, everything works very well next to network adapter, when I start my computer, I see a red x on the icon in the taskbar Ethernet, so I have to go to Device Manager and disable, enable Ethernet controller to make it work, and after doing activate deactivate it works fine but if I restart the system and then the same question It does not load/ethernet adapter network at startup. I'm stuck for the last 4 days, installed reinstalled windows 8 x 86, 64-bit, win 7 x 86, 64-bit. Update bios to J01 V2.25.  all the drivers are updated to the HP website, please. The system is in warranty, but I lost all documents related to the warranty etc. Any help is very appreciated,

  Thank you

  Hello:

  It is a forum of consumer to consumer.  I do not work for or represent HP.

  If the PC is under warranty, you should contact HP technical support to the country that you live on the link below and drop support under the warranty.

  http://WWW8.HP.com/us/en/contact-HP/WW-contact-us.html

• HP Compaq 8100 Elite CMT: Need power supply 400w replacement.

  I ordered a refurbished HP Compaq 8100 Elite CMT Quad Core i7-860 2.80 GHz 8 GB RAM 1 TB HARD drive

  And I ordered a gtx geforce 650 need a 400w power supply. I don't know on what power I need command that will fit in this. Can someone help me?

  Use an adapter for your 2nd diet, it's what has worked for me.

  http://www.eBay.com/ITM/like/111284841995?lpid=82
  5.00 after all my research I've found the answer, it's not pretty, but it works.

  Plug one of your SATA power to branch (from your current diet) on the cable resulting, plug your new power supply ATX ATX plug adapter and you're good to go. When your old power supply switch on the adapter will turn on your new, it's great.

  Add2PSU is an adapter popular http://www.add2psu.com/

  You could buy a dedicated power supply if you can find one, but I recommend not, they are expensive, make a lot of noise and heat.

  It was a nightmare for me and I don't want other people to have to go through what I did.