HP Designjet 111 24 "color sublimation support

Similar Questions

• Designjet 111: HP Designjet 111. Cross any line put in place every time his tour on

  Hello

  I have a HP Designjet 111 with a feed roller.

  The other day one of the printhead needed replacing I did. Now, whenever I turn on the printer, it goes through any line established the points of printing color page. It prints three times which takes about 5 minutes. If I turn the printer market again once he does all this again.

  I tried to replace the print head with one another but same problem. I always use the new genuine HP print heads and HP ink cartridges.

  Once set up over it print without any problems.

  Any ideas?

  Thank you

  This is because it does not have alignment.  It tries 3 times.  Look at the line with the X in the right margin.  It is the color, the origin of the problem.  Just look at the small boxes and you should be able to tell what printhead (s) must always be replaced. If the print quality is very good, then simply press the Cancel button as the first leaf begins to print and it will cancel the calibration.

• Designjet 111: Need for Designjet 111 installation CD

  Hello

  Anyone who has a CD to install Designjet 111?

  I just bought a Designjet 111 opportunity.    I realize the printer is obsolete, of course. But it was sent to me without an installation CD.

  I tried to contact HP support, but I have not found all the solutions.

  If anyone has an installation CD, I would be very grateful if you can let me know if you were happy to part with it and for how much.

  Thank you very much.

  Hello

  You can find the SW installation on the following link

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=11203511 & swItemId = pl_84217_5 & swEnvOid = 4063

• Designjet 111 - printing problem

  My Designjet 111 printed 6843 pages. Almost all were 24 "x 36" CAD. Changes of cartridge & usual ink print head.

  Two days ago the plotter has stopped printing. It was a pdf CAD and got about 1/2 ", then stopped.

  Maintenance of the 532 system error codes:

  # 0, 86.11 S.06.04 SM: 01 [isp_mech (MechCommand.c: 0794)] 10/04/2014 Page # 6844
  # 1 S.06.04 SM 02.01: 01 [isp_mech (MechCommand.c: 0789)] 10/04/2014 Page # 6844
  # 2 S.06.04 SM 86.11: 01 [isp_mech (MechCommand.c: 0794)] 10/04/2014 Page # 6844
  # 3 02.01 S.06.04 SM: 01 [isp_mech (MechCommand.c: 0789)] 10/04/2014 Page # 6844
  # 4 86.11 S.06.04 SM: 01 [isp_mech (MechCommand.c: 0794)] 10/04/2014 Page # 6844
  # 5 02.01 S.06.04 SM: 01 [isp_mech (MechCommand.c: 0789)] 10/04/2014 Page # 6844
  # 6, 86.11 S.06.04 SM: 01 [isp_mech (MechCommand.c: 0794)] 10/04/2014 Page # 6844
  # 7 02.01 S.06.04 SM: 01 [isp_mech (MechCommand.c: 0789)] 10/04/2014 Page # 6844
  # 8 86.11 S.06.04 SM: 01 [isp_mech (MechCommand.c: 0794)] 10/04/2014 Page # 6844
  # 9 S.06.04 SM 02.01: 01 [isp_mech (MechCommand.c: 0789)] 10/04/2014 Page # 6844

  Code of error starting Track = 167 = init PrintHeadControl

  I put in four new print heads with the same result

  Changed the ink also.

  Not sure whatelse to do to get the tracer is going?

  Any help would be greatly appreciated

  Roger

  SOLVED

  You have a printer independent guy tech $80, which has stripped the DJ11 and cleaned, inspected all parts.

  Nothing broken just a lot of cleaning.

  Head of transport that reads the MICR band was dirty.

  HP support (Vijay in India) was useless

  Hope this helps some other users DJ11

  Roger

• Designjet 111 roll: problem with Hp designjet 111 roll

  Hello

  I have problem with Designjet 111 roll. I reinstalled the driver delivered with CD, and the most recent Web site and the effect is always the same. When I enter the Properties window, I see this:

  

  There is no chance to put anything. How can I solve this?

  Hello

  The System Maintenance Utility will not be related to a problem with the printer driver.

  Have you deleted the driver as explained on the following doc?

  http://h20564.www2.HP.com/hpsc/doc/public/display?docid=emr_na-bpp03332

• Designjet 111 (nominal): Designjet 111 / Windows 10 / instead of pointing it prints to the prn file

  Hello

  I use Windows 10 and Designjet 111 (roll). I already downloaded the driver and everything seemed OK, but after printing the confirmation of the window, rather than send the drawing to the plotter, the next window opens to save the drawing as a .prn file. The button "save to file" in the window "Advanced" is clear.

  He had no problem with printing on Windows 7.

  See you soon

  OK, I solved the problem.

  In the printer properties / ports window 'Print to file' port has been marked. I just changed to the USB port.

• Designjet 111 & Jetdirect 635n

  Hi all

  We have a DesignJet 111 and a map of network JetDirect 635n that someone bought for her. When install the 635n and turn 111, it just sits there with the rotation icon and won't work at all. Apparently, do not recognize the card. Any suggestions?

  Thanks Hayes

  This forum focuses on the level of consumer products.  For the Designjet you can have better results, post in the forum HP Designjet here.

• Designjet 111 does not start prinring or stops in the Middle

  Hello

  I recently bought a designjet 111. The first page I printed (linedrawings) came out perfectly, the second page, I tried (linedrawings + a few pictures) the printer no longer starts.

  Now, I have the same problem: the printer just will not start. I tried to turn my laptop and printer, changed USB ports, off the sign 'offline',... nothing seems to work.

  Then all of a sudden it started printing (not sure what I did differently), but stopped after 5 centimeters, drove from the page and cut it. I tried again and then print 30 centimetres and stopped. Now, it does not print at all.

  What can I do?

  OK, problem solved by changing the usb cable to the laptop.

• HP DesignJet 750 c: HP Designjet 750 c color issue

  This is my story!

  HP Designjet 750 c (C4709B) worked well with my Windows 7, until it upgraded to Windows 10.

  After much effort, downgraded the OS to Windows 7 again.

  Now had a lot of trouble finding the driver for Windows 7 64-bithell. Tried all combinations including

  -C 1050 driver

  -Universal drivers

  -Driver for x 64 XP

  -drivers pl532

  Finally found such a suggested in the following link which gave me "HP DesignJet 750 C (E/A0) by HP +" Driver

  http://h30434.www3.HP.com/T5/inkjet-printing/help-me-Designjet-650C-win-7-64-bit/m-p/323398#M502435

  Now the problem is:

  1 plotter prints with universal driver and custom 1050C but only in grayscale.

  2. the driver I have finally installed as per the link above made me a color printing.

  However, it prints color but his race up to half of the way down and cut half of the draw prints about an inch turns to solid black lines
  3. couple of plots with 4 colors on this subject. Displays only one of the four colors.
  4. I see colors on paper, but not in the place where it is supposed to be.
  5. it is never complete and print in black.

  Can someone help me understand if there is a problem with AutoCAD or I'm a bad driver?

  I use AutoCAD 2016

  Kind regards
  Mike

  I don't have any other suggestions, except I would be suspicious of LPT support in Windows 10.  These days there a few computers supporting always parallel ports and very few of these 10 ru windows.  I suspect there has been little or no parallel in Windows 8 or later ports test.

  I picked up a cheap (< $ 20 delivered) network card on eBay, it works fine for me in Windows 10 with this driver and my Designjet 755 cm (and previous Designjet 750 c and 650 c plotters).

• DesignJet 111: DesignJet 111 - printing problems - no printing after upgrading to Windows 10

  Several problems to the upgrade of WINDOWS 7 for WIN 10.

  The HP DesignJet is 'offline' and can't figure out how to change the setting of "online."

  The definition "print directly to the printer" is not.

  Yellow flashing on the printer dashboard - magenta ink cartridge shows empty, but it is full.

  Computer HP printer installed - poster is in the Device Manager - watch "this device is functioning."

  Printer is listed in devices and printers.

  HP Support Assistant doesn't recognize - printer in the list, can not find device during an attempt of "add design.

  Printer turns off or recycle off on after turning on.

  Hello

  If you have a driver problem:

  Remove the driver completely from the computer, then download and install the lates driver.

  Here is the link incase you need

  http://h20564.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=4123145 & swLangOid = 8 & swEnvOid = 4192

  Now, the yellow light flashes on the Panel means that the printer needs attention, like:

  -Close coverage which is open

  -Of paper

  -Paper tilt

  -Jam

  -An error code

  If you have 6 columns on the levels of ink instead of 4 is because you have an error code.

  On the following link, you can find more information on how to prepare the error codes

  http://h20565.www2.HP.com/hpsc/doc/public/display?sp4ts.Oid=352387 & docid = emr_na-bpp03841

  If you have an error code, the printer appears offline on your computer.

  On this other link, you will find how to check other messages on the printer

  http://h20564.www2.HP.com/hpsc/doc/public/display?docid=emr_na-c01669949

• Satellite L650-111 is not in support of Toshiba

  I have the Satellite L650-111 (number PSK1JE-00E00PY4) and when I try to access my computer Toshiba support page
  There is no success. Even if I try to use "detect your laptop" there is no success.

  In full (x) of Toshiba I could not find my model of laptop.

  WHY?

  I am very disappointed whit this situation, still more because as I got Toshiba Satellite A80-129 and together
  all drivers and support are listed.

  concerning

  disappointed with the user

  There is no reason to be disappointed.
  If you are looking for drivers and for some reason any correctly detect works option doesn t there is also a way to find all the drivers manually.

  You have the Satellite L650 with PSK1JE model number. That s all that you need to know.
  Please check again, and if you still have the problem of finding the drivers I will explain how to find them.

• Satellite L650-111 - where is the support for the page?

  Hello

  I bought this computer a month ago and I thought that I could check the support page for this laptop for the new updates. I clicked on the link to Toshiba Tempro (support for my PC or something like that) and to opening my browser there was an error saying that my product have not been found. So I typed my serial code in and also tried the automatic recognition of the system, which came with the same error.
  Even on this list 'find your laptop manually' I saw not only my role model, but the entire series (L650) wasn't there. Is this in any way related to the problem that I recently ("Toshiba Service Station has stopped working")?

  Please also explain what to do in this case. I tried to uninstall manually and re-setup of the station but the problem persists.

  Thank you in advance.

  Hey Buddy,

  You should check this page:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  Then choose the following options:
  Laptop > Satellite > Satellite L Series > Satellite L650 > PSK1JE

  On this page you can find all the updates for it. :)

  Otherwise I agree with Quad: never touch a running system! ;)

• Printhead Designjet 111

  Hi people!

  IM new to this forum and have a bit of a problem.

  I just changed the yellow in my machine print head because he started bands. Once in a new, is not printing at all. There is nothing on the front panel flashes to show that I have a problem. So, just for fun, I put the old back in and still the same, no ink. Sorry for sounding silly, but is - it possible that a 'pump', or something of this ink from the print head pumps gone bad?

  I hate the idea of that something big went wrong shot, because I use this printer for about 5 years with absolutely no problem.

  Thanks in advance for any help.

  chuckj

  This forum focuses on the level of consumer products.  For the Designjet that you can have better results, post in the forum HP Designjet here, this is where the Designjet experts.

• Depth or color not supported mode. Only RGB, CMYK, grayscale, and Bitmap levels are supported?

  Hello. I am trying to replace a string in a CMYK image with a spot color in Illustrator CS6 and photoshop CS6. Change the color, it is quite simple and then saving them as a multichannel DSP. But then it will not be re-issued in Illustrator and I just got the above message. I don't understand why it won't link to. I've done this before with images and are they related in fine illustrator. Am I missing a setting or mode of file somewhere?

  Too bad. I thought about it. Went back to previous files I created and realized that I saved as .eps files. For anyone else having this problem... you can't save a multichannel image as a psd, you have to save to an EPS Photoshop DCS 2.0 then it will very well repeat :-)

• HP Designjet 111 with 24 "Roll: Arch D is no longer available in the print options

  Normally print us PDF drawing (using Adobe Reader) set to Arch C (18 "x 24"), but sometimes we need D Arch (24 "x 36").

  Ark D has somehow been removed from our drop-down list of options. When I try to use customize the size of 24 "x 36", I get a pop up window that indicates that the size is too small or too large. I don't see any other way to add Arch D in the list of options.

  I tried the update of drivers, but the message says I have the latest. We have been updating for Windows 10 a few months ago and I don't know that it had no effect on these options.

  Thanks in advance for any help.

  Solution, it turns out that the printer now ready for print Arch C value by default, and in the settings is a checkbox to rotate 90 degrees.  When this element is on the Ark D option disappears from the list of options.  Note: Also noted that under the 'effects' tab / resizing Options, we set to Arch C, I think that's the main problem of the loss of the ability to print Arch D; Choose 'full size', now able to print once more drawings D arc.