HP designjet 5500 magenta in the images n & b

Similar Questions

• DesignJet 5500: print head print test very good page, but I still get the error message to replace the printhead

  On my DesignJet 5500, I rswitched the ink tubes, printheads and printhead cleaners dyeing anti-UV, 81 to 83.

  I got an error message saying that the black print head needed to be replaced so I bought another head black printing and after that, I was able to print a test page that shows all the colors (image quality page?).

  Magenta not give not any code of error before, but now I get an error message saying that the printhead magenta must be replaced, even if magenta print well on the printed test page.

  Hello

  The printer give you a warning when the health of the print head is low, but it will continue to print.

  If the problem has been solved after all print head replacement can be that a print head cause others to fail

  Or, just a few bad print heads

• Designjet 5500 does not print a color (Magenta), head scratcher

  Hello all and thanks in advance. I'll try to be brief with my problem. I was wondering if anyone of you advanced users have experienced this problem and if I am wrong in my assumptions: granted Designjet 5500, work status unknown, for my personal use (mainly CAD). Replace the belt, system of tube of ink, cartridges and printheads (belt was shot, the ink tube sank cyan) system started successfully with print heads of installation showing all 6 colors of ink. Ran diagnostic impression. Magenta is totally absent in prints of Diagnostics 1 and 5. Not even a trace of color. I tried the calibration and fails with the error 6009, understandable. tubes of ink to the transport still show all 6 colors. printer initializes generally very good, with all the list OK print heads (because they are all new!). But sometimes throws an error 0032 00000004 0c fall detector, but not always. Fall sensor cleaned. My thought is that the Magenta Printhead is about shooting. Given that all the tubes of ink and no ink bubble comes OK. The fact that she sometimes error 0c 0032, but sometimes not, said that the printhead magenta must be fired sometimes at startup. So, I intend to replace the rear cart cables as the next logical step. Notice please! Thank you! Ray

  The first you see, it's actually the flowing magenta printhead ink. Take a damp paper towel, then press the printhead magenta in the towel and you should get two lines of ink. If you need a comparison, take the black and do the same thing. If you don't get two complete lines, then you can try to soak the print head in warm water (the temp) for about 2 minutes and pat dry with paper towels. Most of the time you can tell right away because when you place a print head in hot water should flow little ink and water take on the colour of the print head. Also make sure that it is not the magenta head light print and magenta. My feeling is that if you have a problem of thin cable you get an error message since the main Board check electrical connections to the print head during initialization, and when printing. Since you are not getting a failure than this message means electrically the printhead and the connections that are very well and this is the part of print head that is clogged or not working do not.

• DesignJet 5500: Where can I download the media for ink UV #83 profiles?

  The links below allow you to download media for DesignJet 5500 profiles.  First you must choose your computer operating system.  If you select Windows 7, you won't see listed media profiles.  If you select Windows XP, you will see 10 types of listed environments.  If you click on one of the listed media types, then look at the file name to download, all file names have "dye" in the name of the file.  Where can I download profiles of supports for UV #83 inks?

  HP download page for media for inks Dye #81 profiles

  For 5500 HP media profiles page

  http://h20564.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=82231 & swLangOid = 8 & swEnvOid = 228

• AIP - SSM recreate the image in secondary ASA 5500 (failover) with virtual contexts

  Hello guys,.

  The scenario is as follows:

  2 ASA 5500 with virtual contexts for failover.

  The ASA elementary school has the work of the AIP-SSM20.

  ASA school (which is in active / standby) has its SSM20 AIP to work now and everything is in production.

  Someone tried to configure this 2nd AIP - SSM, changed the password and lost, so I tried to re - the image (without authorized passage recovery), but the connection fails on the TFTP server, where is the image of the AIP - SSM.

  Now questions, documentation Cisco re-imaging view orders under ASA #.

  but as this scenario has several virtual contexts the ASA # shell contains no IP address as you know (which I suppose is the reason why the ASA cannot download the image from the TFTP server) and switch to another context (ASA / admin #) re-imaging commands do not work (hw-module module 1... etc...).

  What is the solution? Is there documentation for it (with security contexts)?

  Thank you very much for reading ;) comment on possible solutions.

  Yes,

  Some things to keep in mind.

  (1) run 'debug module start' on the SAA before running the command "hw-module module 1 recover boot. This will show you the ROMMON of the MSS output as it tries to make the new image and you can look for any errors.

  (2) before trying to download from the SSM, first use a machine separate download tftp from your laptop. This will ensure the TFTP on your laptop works and confirm what directory (if any) that you can use as the file location.

  (3) if the tftp download does not SSM, then the SSM is unable to properly connect to your laptop. You need a crossover cable to connect your laptop to the SSM. If you have a crossover cable, then you could try to connect the MSS and your laptop to a small hub, or configure a new vlan on your switch with only 2 ports and connect the MSS and your computer laptop this vlan 2 port.

  (4) also try the download first at the end of the gateway to 0.0.0.0 since your laptop and the SSM will be on the same subnet. If this does not work then you can try a non-existent 30.0.0.4 address as gateway.

  (5) understand that the IP address that you specify for the MSS using the command "configure the hw-module module 1 recover" is just temporary for download. Once an image is installed, then sitting at the module and run the "setup" command in order to configure the permanent address you want ure on external port of the SSM. This address in the "setup" command can the same as that used in the command 'get the 1 hw-module module configure' or a completely new (as in your case). Just make sure that you connect to the network just to what address you give.

• DesignJet 5500: firmware update error

  The firmware on my printer is: S.03.12D

  I went to this URL:

  http://h20566.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=82219 & swLangOid = 8 & swEnvOid = 181

  and downloaded the firmware under Windows 2000, even if I have Windows 7 64 bit on my computer because I thought that the firmware was just download to the printer, so it should matter what OS is on the computer.

  I downloaded S.56.07 February 3, 2009

  I downloaded the firmware to the printer file and it improved up to 97% and then gave the error message below.

  An unexpected error has occurred. Make sure that the firmware you are using is a valid firmware file.

  I have a Designjet 5500 and I went from dye in ink UV, if that matters.

  The printer seems to be ok, but it would be good to know how I can upgrade the firmware.

  Yes, a connection between the computer and the printer is recommended.

  Version of the OS is not the problem here, but exact number of the product will make a difference, so please use the actual peripheral product number.

• DesignJet 5500: DesignJet 5500 error 5015

  I have a 5500 DesignJet.  I changed the ink, cartridges and the dye prinheads 81 to 83 UV tubes.

  I get error printhead code 5015 (only the black print head) which is a print head "internal power failure" or "Printhead Cleaner is not correct type" according to which manual checking.

  I didn't know that the printhead cleaners are different. How does the printer know vacuuming is of the wrong type, is there a chip in the vacuum?

  Anyone know where I can buy cleaners printhead for a reasonable price?

  Or, is it an internal electrical failure of print head? And, is it possible to disassemble the print head and set the internal electrical failure?

  The first hypothesis is correct.  The black print head has a power outage.  I would replace the print head first.  See attachment.

• Designjet 5500: HP Designjet 5500 - failed hard drive?

  My next plotter Designjet 5500 has the error message: "failed to start.  Error: 1f50007.  Hard drive failure. "I took out the hard drive.  Then I took a good hard drive on another plotter Designjet 5500 I have here (he has other issues, but the hard drive is in good health) and installed it in the abacus of 1st.  He repeats the same error message (i.e., "failed to start.  Error: 1f50007.  Hard drive failure. "I took that hard drive back out and put back in 2nd tracer and it always starts very well.

  For me, this means that probably the hard drive is not really the problem with my 1 tracer because I put a hard drive perfectly well in and he said that the hard drive has failed.  It seems that something has no who is now saying the plotter that there a defective hard drive when it's not the real problem.  Someone else this experience?  Pointers for me on what to look for or what would be my next step in troubleshooting?  Not covered in the manual on the defective hard drive errors.  Only how to remove and install a.

  Thank you.  Erica

  Unplug the printer.  Loosen the screws and remove the print server plug at the back of the printer (he shoots just to the outside), then take the back cover off long.  Look for the two lights, amber and one green on the circuit on the left.  Lights are on the top left of the Board of Directors (main PCA).  If you do not have both lights then it is most likely doesn't have the power of power supply Board (the circuit board to the right of the hard drive).  My experience has been that when the power Board fails, the error you see is that the hard drive will not start.

  If you have already tried a known good hard drive and have the same defect, it is most likely the problem.

  Tell us what you find.

• Designjet 5500

  Designjet 5500 very slow printing in-house and with impressions from pc. Using the same driver as two other beautiful print 5500's. Almost as if the plotter is having to take the time to think between each pass. An impression of internal configuration took about 5 minutes or more to print. Maybe the firmware? At a loss.  Any ideas or suggestions would be a great help... Thank you.

  P.S. This metric has been moved from laserjet for Designjet - moderator of the HP Forum

  Remove the network adapter with the power off and power back on and see if the internal printers are faster. If they are, do a search of this site for the cooking of the network card. It is about 95% of the time. If still slow with the printers internal perhaps you experience memory problems. Swap the memory and even the bootrom of the other chip to see if that makes a difference.

• On the image in print quality

  Sometimes, you will notice that when you print an image it does not appear as expected, the colors are just a little off - step as vibrant as you want it to. There is a reason for that, and that's because when you transfer an image on your computer the colors for the image change slightly.

  In the real world and in printing, the colors come from three primary colors - Cyan (light blue), Magenta (Pink) and yellow.  Then there is black which gives depth and a sound signal (CMYK).  However, on your computer screen, you're dealing with a different method. Most of the screens are made up of small LEDs that flash at very high speed to give you the colors you see. These diodes are blue, red and green (RGB).

  Now, these two color combinations are very similar, this is why there is not a radical change, and for some, this change might not be noticeable. Here is an example of printing from the computer-

  

  While this image is superb, the tones in some areas are a little more muted due to how the file was subtly shifted from CMYK to RGB. Now, you can find the details of this image by carefully creating presets for photo through various programs that essentially make up for this change, but there are other easier methods, I found.

  The first of them is to use ePrint. If you have a printer with web functionality, send the photo via email diretly to the printer cancels the transition and renders the image as it was originally. Not all printers have this feature, but it is becoming more common on many newer models often.

  The other method is one that you can use your printer directly if you have a card reader / USB port. Imbernon or load the image on one of these devices you can print again directly avoiding the color conversion. This will give your images a more pristine quality. Take a look at the same image printed directly from a USB key.

  

  Just a little more dynamic and has just a touch more in detail. To get the best quality and results, sometimes it requires outside the box thinking. Generally this method will provide you with great results without any necessary error.

  However, it is important to note that if you want to convert or use a format other than .jpg, it won't work, and you try to change the settings on the program that you use to compensate for the shift in color.

  I hope this information is useful to you guys, if you have any questions contact me for more help!

  Here's a cute baby tiger too!

  

• Photosmart D7260 won't print magenta, though the status says ok

  Dark magenta has more ink, replaced the cartridge status shows 100% and click ok, but do not print magenta color, test page does not print light or dark magenta bars have performed maintenance cleaning printhead several times, still does not

  Solution - I found the image more red, I had (wrapped Christmas gifts) clouded the Red a lot, then printed on a dozen pictures for magenta flowing.  It seems to have worked. Apparently, there was a clog or the dried ink from the printer where I didn't replace the magenta cartridge empty for so long. Good luck with yours.

• Is it possible to sort the images by file name?

  I imported a record of 200 images in Photos for OS X (El Captain). Image files have been appointed in the order - I want them to appear in a slide show: photo_01, photo_02 etc...

  Once I imported the images - I found them all out of order - and the only options I can find in the view menu are somehow 'oldest first', 'newest first' or ' title '. Please, someone tell me I'm missing something obvious - he and not that Apple chose to omit the possibility to sort the images by name? If this is the case - I'm speechless - how is f - ing stupid!

  Sort by file name is not an option in the Photos. Albums and smart albums you yourself set can be sorted by name, date of capture, or manually.

  Sorting through the predefined albums is automatic:

  • 'Photos' display with moments and collections is sorted by date of capture and the location.
  • 'All the Photos' display is sorted by the date of the import session.
  • Other built-in smart albums are sorted by the date of capture.

  You can see the current sort order, preset, if it is grayed out in the "view > sort ' menu.

  As a workaround:

  1. If you need to want pictures to be sorted by file name, copy the name of the file in the title field. Then, create a smart album of the items and sort by title. We have posted a trick to copy the name of the file in the title field for the selected photos: Script: change the title filename without Extensionor: Script: batch change the titles of the Extension/w
  2. Or view your photo library in pictures of power.  This versatile tool lets you browse photos as a list or thumbnail while looking the other metadata under the thumbnails or displayed as list with columns selected and sorted by columns.

  You can do a lot with the free trial: download PowerPhotos here: Fat Cat Software-PowerPhotos

• Update to iOS 10 stops to record the Image of emails

  After the upgrade to iOS 10, I can to is no longer tap and hold on an image received and displayed within an e-mail message to save the Image from my camera in a context menu. Instead, it seems to only be able to save the text of the URL associated with the image. Ditto for images of websites in Safari.

  Here's how 'save image' is done 10 IOS:

  • Tap and hold the photo (or video)
  • Press "Quick Look".
  • Tap upward facing arrow coming out of the box (lower-left)
  • Press 'Save Image'.

  http://help.Apple.com/iPhone/10/#/iph845853585

• replace the image number

  is it possible to remove the camera given the number of image and replace it (in a change of badge) with a personal number (is it possible in Aperture)?

  No - you can add a title that can be displayed below the image

  LN

• When I click on "Copy picture", when I use the dough, it's to show the image URL

  Hello

  I'm having a problem about the exemplary Image resource. I need to copy and paste a lot of images to work.

  I click on an image, holding control and then press "copy picture". But when I paste, it shows the URL of the image and not the image. I tried on different browsers and apps, but the same error occurs.

  Can someone help me please? How should I do? It has changed from one day to the other.

  Thank you

  It looks like you use context Menus to copy your images. Depending on your machine or software, each user will have different contextual shortcuts.

  You might do better to use an application like SnapnDrag, which is free in its basic mode.