HP Deskjet 3052 has error code...

Similar Questions

• HP Deskjet 2640 series: Error Code

  Dear Sirs,

  I was faced with a problem with my all in one printer HP Deskjet 2640. Specifically, the printer suddenly showed an indication of error on the screen and refuses to print, reset or accept all orders by the laptop. The error code displayed is as follows:

  Error code

  OXC4EB11C9

  C HW_MICCI2

  As there is no indication of the error category (i.e. ink, cartridge printer software drivers etc, I am unable to determine the source of the problem. I would be grateful if you could throw some light on this subject.

  Thanking you in advance

  Hello emandal,

  Welcome to the HP Forums.

  I see that you have a problem with the error code "OXC4EB11C9".

  Please click on the following link which deals with HP monofunctional and printers multifunctional - an alphanumeric Code (' example: ' 0 x ' r 'C2...) ") displays on the front panel when printing.

  If troubleshooting doesn't help not solve your problem, then I would say call the HP Technical Support to see all the other possibilities for you. If you call in North America, the number is 1-800-474-6836 and for all other regions, please click here: click here.

  Thanks for your time.

• List HP DeskJet 930C printer error codes?

  Hello, where can I get a list of the error codes printer´s HP DeskJet 930C printed on the page of diagnosis and their significance? As 90020302 etc.

  To answer your question regarding the list of error on a diagnostic test codes, I have never seen a list and I'm looking for very long.  To my knowledge, the diagnostic report means more to engineers.  Usually, each digit represents certain aspects of the trial.  If you have problems with the printer or are you just trying to understand the test page printed off the coast?

• Microsoft LifeCam suddenly stopped working, has error Code 43

  I have been using an external camera from Microsoft "Microsoft LifeCam" on my Toshiba 305 and suddenly it has stopped working & and/or is therefore most recognizable when it is plugged.  Any suggestions on how to put it on again.  The camera that came with this Toshiba 305 is very grainy and looks like maybe the goal was scratched and does not have a good video image and the external camera did a great job for me with this laptop.

  One of the "warnings" or troubleshooting of the menus said the following:

  Intel (R) 82801 G (ICH7 Family) USB2 Enhanced Host Controller

  Windows has stopped this device because of problems (Code 43)

  Help!  and thank you Bill in Chicago!

  Hello Bill,

  Thanks for posting your question on the Microsoft Community forum.

  I apologize for the inconvenience caused to you.

  I understand that you have a problem with Microsoft life camera stopped working in the system and get the error 43.

  This issue would have occurred because drivers have been corrupted in the system.

  I would suggest trying the following methods and check if it helps.

  Method 1:

  Error codes in Windows, Device Manager please follow the steps in the link provided and check if it helps.

  http://support.Microsoft.com/kb/310123

  If the problem persists, please follow method 2.

  Method 2:

  Code 43: Windows has stopped this device because it has reported problems, please follow the steps in the link provided below.

  http://TechNet.Microsoft.com/en-us/library/cc725873 (v = WS.10) .aspx

  If the problem persists, follow method 3.

  Method 3:

  Troubleshooting for the failures to find the new LifeCam hardware, please follow the steps in the link provided below and check if it helps.

  http://support.Microsoft.com/kb/929087

  Note: To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows

  For reference:

  Please refer to the procedure described in the article below.

  Troubleshooting: Webcams

  http://www.Microsoft.com/hardware/en-us/help/support/troubleshooting/webcam/LifeCam-Setup

  Hope this information helps. If you have any other questions feel free to respond and we would be happy to help.

  Thank you.

• HP Deskjet 3052 has not recognized on my network

  Several times, I am not able to send documents on my HP 3052 a wireless Deskjet printer. To get it to print it looks like I still have to go back through the installation program for the connected printer. Then the next day or two later, I can't print again. I have a DLink router and a DLink Extender (DAP 1360). The range extender provides mainly internet to a desktop computer. Wireless, it receives the signal of my main router (DGL-4500) and is physically connected to my desktop computer, internet provision. Have a range extender would have something to do with my printer always lost connection to my laptop in my house. I spent time online with the support of 'pay' Dlink with no result and did not want to continue to pay for nothing. Can someone give me some advice on what I can do to keep my printer on my network? Please let me know if I need to provide more information. Would be - what my router goes wrong? I have no idea and really need help as this has been hard for some time now and is very frustrating.

  What version of Windows you have, including the service pack?  I will assume that you have little variety of Windows 7, as you have posted in a forum of Win 7.

  I guess you want to print directly (wireless) to the printer instead of use the ePrint feature.

  You never turn off the printer or leave you it on all the time?

  I suspect that what is happening is that the printer receives a new IP address assigned by your router.  This can easily happen if you turn the printer off and also a number of other devices on the network (for example, your laptop) are not always present on the network...  The diagnosis and the solution to this problem are relatively easy (it takes just a lot of words to describe them)

  Diagnosis
  Using the controls on the front panel of the printer, print a Network Setup page:

  1. press the button to display the wireless wireless.
  2. in the wireless Menu, select print reports.
  3. in the menu printing reports, select Configuration

  Take note of the printer IP address, subnet mask and default gateway on the Network Setup page

  On a computer on which you installed the printer go to devices and printers
  Right-click on the icon for the HP 3052 has, and then select properties from the printer (NOT the same as 'Printer Preferences' or 'Properties')
  Select the "Ports" tab
  By ensuring NOT to click inside the list of ports, use the slider to the right of the list so that you can see the line highlighted and verified which indicates the port used for this printer.
  If necessary, click and drag on the vertical line that is low in between "Port" and "Description" header, so that you can see the complete port identification.
  Make a note of the port.
  For now, click Cancel to exit the properties of the printer.

  If the port shown on the network configuration page and the port specified in the printer properties dialog box are different, that's your problem.

  Solution (assuming that the wrong port is the problem)

  Printers and other similar devices on a network must always be assigned a static (fixed) IP address so that users of these devices (for example, computers connected to the network) can find them.

  Open a browser on a computer connected to your network and enter the IP address of the printer that was shown on the network configuration page.
  You must be connected to the configuration utility based on the web of the printer.  Follow the instructions in the support page this HP to set a static IP address for the printer.

  You can see the range of IP addresses used by your DLink DGL4500 by entering its web-based configuration utility (in your browser, go to 192.168.0.1) and look at the tab "Basis" of the network (see page 30 of the Manual).  It seems that by default the router is to assign addresses in the range 192.168.0.100 through 192.168.0.199.  Use an address outside this range for your printer for example, 192.168.0.25 or 192.168.0.250.  It is ESSENTIAL that the first 3 "bytes" of the IP address remain the same (i.e. 192.168.0).  The only part of the IP address you should change is the last "byte".

  You will need execute the steps described in the next paragraph on EACH computer you want to use to print to this printer.

  In some printer software, HP seems to have included a utility named "Update"IP address"(see directions link above HP).  I'm not familiar with this utility, but his name, if you have it and run, you should then be able to print.  If you don't have the utility, you must manually update the IP address that Windows uses for your printer.  Do so you by going into the "Ports" tab as described above and then clicking on the button 'configure the Port '.  On the next screen, enter the new static IP address that you assigned to the printer and OK your way out.

• Time machine is unable to perform a backup. Not able to access the sparsebundle. Problem occurred first on snow leopard OS. Followed Dragon upgrade to El Capitan. Only difference has error code of 109 changed to null. What about someone?

  Time machine is unable to perform a backup. Not able to access the sparsebundle. First of all, there is problem with the Snow Leopard operating system. Dragon followed in the upgrade to El Capitan. Only difference was error code 109 changed to 'null '. What about someone?

  We need some info.

  You can access from the finder Time Capsule? If this isn't the case, then Time Machine will not work.

  You upgrade the computer snow to El Capo and keep the same name?

  If you want to backup, it is best to start again... clean the new backup any attempt to add a previous backup failed.

  I recommend that you actually erase the TC... do a complete factory reset and start again.

  The previous backup if necessary can be archived on a USB drive connected to the TC assuming that Airport utility can still access it. Airport utility accesses the TC?

  With update installs all sorts of things can go wrong... so tell me more if you can not get anywhere.

• Z6100: HP Z6100 has error code 46.03

  Hi can someone tell me how to solve this you problem. HP Z6100 error code 46.03 a. I checked the print heads and replaced two that showed not defective on the machine but seemed marked for me. It happened after a paper jam... Thanks kerrie

  Kerrie Hi, how you doing?

  Unfortunately this error it is necessary repairs.

  Ther service manual check below:

  http://www.partsnow.com/docs/service-manuals/HP-Designjet-Z6100-service-manual.PDF

  Page 62 Chapter 2 System Error Codes:

  System error:

• HP deskjet 3052 has works on my wifi after I reset the printer / modem/router - but failed later

  I had my HP Deskjet 3052 a work from PC, MAC, iphone / ipad on my Airlink wifi after a reset on the printer - router - modem.

  It fails when I try to use it later in the day - unless I'm resting again.

  Do I have to reset each time I print?

  New modem/router solved my disconnect problem - but I still cannot connect my imac running Mac OS X 10.5.8.

  I am connected to the wireless - i.e. - accesses the internet, I cannot connect deskjet - is told by the way now I hace a 3520e model - instead of the 3052.

• DeskJet 3052 has

  Print very slowly. Have reinstalled without change. Link on the forum describing the solution is broken. Thank you.

  Welcome to the timmtam forums

  I saw your post on the printing problem slow that you are having with your Deskjet 3052 a. I have a suggestion for you below. Please, try the troubleshooting steps.

  Slow printing

  Let me know the results!

  Have a nice day

• I'm unable to scan a multi-page document. HP Deskjet 3052 has J611

  I'm unable to scan a multi-page document. I tried everything, re-installed the driver and studied the help settings and there is nothing. Once I scan a page it allows me only to save it and not to add another page to the document. I can't send a pdf CV by attaching two separate pages. I have scanned multiple pages documents other HP scanner and never stumbled on this dilemma. I am running Windows vista and the printer is the printer HP Deskjet 3052 a J611. Help, please.

  Hello

  Don't forget to run the scan of the computer to scan several pages.

  Open the HP software and click on scan a Document or Photo.

  Select the PDF shortcut and if ensure that the dialog box overview checked to be disaplayed.

  Make sure that the resolution set at 300 DPI or lower (any higher resolution does not support multiple pages) and click Scan.

  Use the button to add additional pages until you are finished, and then click Save.

  Shlomi

• Updates Windows installs, has error code 66 & 80070643

  Error code 66 & 80070643 appear when you try to install upgrades to windows 7. Happened since then went from broadband to the Wi - Fi

  * original title - computer will not install the updates of windows. Gives the error code 66A & 80070643. Previously no problem on broadband but since I use wireless connections problem is constant. No windows at all.* payments

  You can see this discussion earlier, linked: http://social.answers.microsoft.com/Forums/en-US/vistawu/thread/f1dd866f-85b7-4ae6-bc32-1c488c19742a ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• (KB951847) x 86 has error code 0 x 643

  Update installation failure what to do?

  When you try to install an update for .NET Framework 1.0, 1.1, 2.0, 3.0 or 3.5, you may receive Windows Update '0 x 643' error code or error code Windows install "1603".
  http://support.Microsoft.com/kb/923100

  When installing updates using Windows update or Microsoft Update you may receive error 80070643 0 x or 0 x 643
  http://support.Microsoft.com/kb/976982

  Windows Update error Code 663 (kb951847) x 86 fails to install

  Windows update fails with error code 0 x 643
  XP, updates Auto, KB951847 and error code 0 x 643
  Error code: 0xC0000005 (cannot install KB951847)

• Windows XP - NICs has error code 10 - impossible to start this device.

  I tried to install McAfee 2011 on my pc and now I can't access the internet. I am running XP. Explore the msg on the internet says no card no installed wireless network. I checked the properties of the network connection and found one of the adapters network error code 10 - impossible to start this device. Since I have more access to internet to download the drivers, etc., how can I fix this problem?

  Hello

  I suggest you to download the latest network adapter driver by using another computer and transfer to the computer that is causing this problem and install the same.

  For more information about the error 10 code refer article.
  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers
  http://support.Microsoft.com/kb/943104

• I have a G62-355DX laptop and is 11 months old. and it won't start. It has error codes

  I have a G62-355DX laptop and is 11 months old. and it won't start. There error codes when I do a test of the system. DST short: failure failure ID: RTX6T9-5B75S5-XD003F - S 60, 903.

  Product ID: XH068UA #ABA

  Hello

  As the error code relates to a short drive Self Test failure - the only real solution to this is to replace the hard drive.

  As your laptop is still under warranty, contact HP to make arrangements for the replaced disk.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  Kind regards

  DP - K

• HP Deskjet 3059A: 0XB807A80C error code

  I get an error code 0XB807A80C on the screen of the printer. I read that it could be in trouble with the printinghead. The printingheads are cartridges, or not? The main question is: is this repairable? and how?

  I only use original cartridges.

  Thank you

  Reference:

  http://support.HP.com/us-en/document/c01458034

  Also this thread:

  http://h30434.www3.HP.com/T5/Ink-toner-cartridge-printhead-issues/do-you-have-an-ink-system-failure-0xC-error-message/TD-p/740567