HP ENVY 17-j020us Quad Edition Notebook PC RAM and SSD update

Similar Questions

• How do I change or update the graphics card on a HP ENVY 17 - j020us Quad Edition Notebook PC

  I want to know if I can add another video card or if I can swap the video card to intel-4400 HP provided with this computer. I tried to look on the sites of HP and may not know if the graphics card is integrated or if she is separated.

  Hello

  The 'Intel HD graphics 4400' is soldered to the motherboard (or integrated) and you can not change or Exchange. You have to live with it and save the money to buy another machine.

  Kind regards.

• HP ENVY 17-J020US: could not find the drivers for my HP ENVY 17-J020US Quad Edition

  Hello

  I have a HP ENVY 17-J020US Quad Edition and I'm looking for "Intel HD Graphics Driver". The Support page and House HP driver heading the wrong driver and HP support was no help. The graphics card is an Intel HD Graphics 4600. Operating system is Windows 10-64 bit updated since Windows 8.1. Any help would be greatly appreciated... Thank you

  I rolled back to Windows 8.1. It's not worth the hassle, but thank you for your suggestions. My main problem was, I couldn't open RAW files in Photoshop using the GPU. This occurred after the upgrade to Windows 10 so I decided to go back because all the drivers that you mentioned, I already had on my system. Thanks again for all your help and Merry Christmas.,.

• ENVY dv6 7300 Quad Edition: ability to RAM of ENVY dv6 7300

  I want to improve my laptop HP dv6 ENVY 7300 Quad Edition of 8 GB to 12 or 16 GB, but I don't know if there is a maximum limit of RAM on my system. Also, is there one or two RAM ports on this device?

  @ironbesterer

  This is your manual.

  http://h10032.www1.HP.com/CTG/manual/c03591281

  Two customer accessible/upgradable memory module slots

  Supported dual channel DDR3 - 1600 MHz

  Supports up to 16384 MB of system RAM

  Start on page 5.

  REO

• HP ENVY 17-j020us Quad Edition: installed SSD and Windows 7, now the laptop will not boot

  I replaced my hard drive Windows 8.1 with a PNY 240 GB SSD and Windows 7 64-bit.  Everything worked very well! Installed all the drivers, everything has worked very well!  Restarted several times, everything worked fine!  Portable stop for the night, the next morning I turn on the laptop and get this error message:

  "not found boot device, please, install an operating system on your hard disk, hard disk 3F0".

  I've traveled different repair procedures using the ERD Windows 7 without change.  I have reinstalled Windows 7 with SSD formatted as GPT drive, received the same error message:

  "not found boot device, please, install an operating system on your hard disk, hard disk 3F0".

  I have reinstalled Windows 7 SSD formatted as MBR disk withs, received the same error message:

  "not found boot device, please, install an operating system on your hard disk, hard disk 3F0".

  I removed the SSD to the laptop and placed in a desktop pc, pc works fine, no problem with the SSD.  SSD in laptop, got the same error message: "boot device not found, please install an operating system on your hard disk, hard disk 3F0".   I don't know where to go from here.

  Help please...

  Okay, I'm running.  In the System Configuration UEFI clicked 'Load HP Factory Default keys', this restored "Secure Boot" who has restored the laptop as long as you work!  Thanks for the help.

• HP ENVY CTO 7300 dv6t Quad Edition Notebook PC updated bios - win7

  Hello...

  I WANT HP dv6t-7300 CTO Quad Edition Notebook PC , it came with win 8 that I demoted for win 7, I received my drivers of HP Pavilion dv6t-7000 CTO Entertainment Notebook PC.

  I have problem of heat and I want to update Bios, the current version: Insyde F.29 03/10/2013.

  He tried to update pavilion dv6t-7000 me gives error message:

  .. . How update the bios?

  You don't Flash the BIOS unless you get the upgrade for the BIOS of the page of CTO Quad Edition Notebook PC drivers HP ENVY dv6t-7300. Since there is no upgrade BIOS listed on this page, there is no way to upgrade the BIOS. Depending on the exact systemboard and the OS that is installed on your computer, the HP part number will be something like "682174-501", which means "Windows 8 Standard / 2.0 GB of discrete video memory / 45 Watt CPU. The comparable numbers for the dv6t-7000 series is 682174-001, which means "Windows 7 / 2.0 GB of discrete video memory / CPU 45 watts.

  The MAIN of the BIOS is different version, the routine will not allow BIOS flash. IF you force it, you can make your computer does not work. DO NOT try to Flash a BIOS that does not support your computer page.

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• HP ENVY 15 t-j000 Quad Edition: HP ENVY 15 t-j000 Quad Edition Notebook PC - white screen

  Hello

  I have a HP ENVY 15 t-j000 Quad Edition Notebook PC. Recently I started to notice a problem on my laptop.  I have some...

  Help, please!

  Hey @HPENVY15t-j000,.

  Unfortunately your laptop is not setup for a touch screen. This is a link to your page 27 manual replacement parts.

  I hope this helps.

  Thank you.

• ENVY 15-j059nr Quad Edition No.: hard drive DST short test failed

  My laptop HP ENVY 15 - j059nr Quad Edition PC notebook does not start. I ran diagnostics test quick HP UEFI using ESC + f2 to restart, the hard drive failed the short DST test with failure code 64NC9H-6TA85K-MFGJWK - ST 60, 03. What does this code mean.

  Hello

  Yes you can.

  Kind regards

  DP - K

• dv7t-7200 CTO Quad Edition Notebook PC - errors after 8.1 update update and HP

  I have a HP ENVY CTO 7200 dv7t Quad Edition Notebook PC
  Product number: B6B75AV

  Originally from Windows 8 Pro with Media Center 64-bit

  Upgrade to WIndows 8.1 via the shop
  Everything seemed OK

  HP Support Assistant eliminated 2.1.0.1002Ap4 contained in SP58398 which has updated the driver Intel Rapid Start Technology.

  (A) after the start, I now get an office messages "your system seems not to have Intel Rapid Start with technology."

  (B) if I start the Intel Control Center, I get the message "there is currently no application filed.

  (C) if I start the Intel Rapid Start Technology Manager, also get "your system seems not to have Intel Rapid Start with technology."

  (D) also, if I try to use an application to read data S.M.A.R.T, which also fails

  (E) However, I get the info of PassMark DiskInfo:
  SysInfo DLL Version: SysInfo v1.0 Build: 1041
  Export: 16:18:18 November 18, 2013

  The device information:
  Device ID: 0
  Interface: RAID
  Capacity of the apparatus: 715402 MB
  Serial number: {information}
  Model number: ST750LX003-1AC154
  Firmware revision: HPM1
  Sheet music:
  N/A

  The ATA information:

  Geometry of the disk:
  Cylinders: 0
  Tracks/cylinder: 0
  Sectors/track: 0
  Bytes/sector: 0
  Total of the sectors of the disk: 1465149168
  Logical sector size: 512
  Physical sector size: 4096
  Media rotation speed: 7200 RPM
  Buffer size: 0 KB
  The ECC size: 4 bytes

  Compliance with standards:
  ATA8-ACS taken in charge: Yes
  ATA/ATAPI-7 taken in charge: Yes
  ATA/ATAPI-6 supported: Yes
  ATA/ATAPI-5 support: Yes
  ATA/ATAPI-4 taken in charge: Yes
  Series/parallel: Serial
  SATA 3.0 Compilance: No.
  SATA 2.6 Compilance: Yes
  SATA 2.5 Compilance: Yes
  SATA II: Ext Compilance: Yes
  SATA 1. 0a Compilance: Yes
  ATA8-AST Compilance: Yes
  World wide ID: 5000C5005DF1063B

  Feature support:
  CHIP supported: Yes
  CHIP enabled: Yes
  SMART taken self-test supported: Yes
  SMART error log supported: Yes
  Taken LBA supported: Yes
  Taken IORDY supported: Yes
  CFast taken in charge: No.
  Taken DMA supported: Yes
  DMA multi-word maximum mode supported: 2
  DMA multi-word selected: None
  Ultra maximum DMA mode supported: 5
  Ultra DMA is selected: 5
  Maximum PIO mode supported: 4
  SATA compliance: Yes
  Supported NCQ priority information: No.
  Unload while NCQ commands are exceptional supported: Yes
  The event of PHY counters supported: Yes
  Application of sustained power management: No.
  Set of features taken NCQ support: Yes
  SATA Gen2 signaling speed (3.0 Gb/s) supported: Yes
  SATA Gen1 signaling speed (1.5 Gb/s) supported: Yes
  Software Settings Preservation: Supported, enabled
  Provision of data in the order: unsupported
  Initiate power management: supported, Enabled
  DMA Setup self-actuation: unsupported
  Buffer of zero offsets: unsupported
  Trusted Computing taken in charge: No.
  Host Protected Area (HPA) taken in charge: No.
  Read-ahead support: Yes
  Predictive read enabled: Yes
  Support for write cache: Yes
  Cache write-enabled: Yes
  Power management support: Yes
  Security mode supported: Yes
  Security mode is activated: no
  Device Configuration Overlay (DCO) taken in charge: Yes
  Supported 48-bit addressing: Yes
  Auto-acoustic management (AAM) supported: No.
  Start standby (THEN) supported: No.
  Advanced Power Management (APM) taken in charge: Yes
  Advanced Power Management (APM) enabled: Yes
  Current level of APM: Minimum energy without waiting
  CompactFlash Association (CFA) taken in charge: No.
  General Purpose Logging (GPL) taken in charge: Yes
  Streaming support: No.
  The media card support through: No.
  Supported power conditions extended: No.
  Scope of supported status reports: No.
  Writing-reading-check supported: No.
  Supported free-fall control: No.
  TRIM command support: No.
  SCT command transport supported: Yes
  NV Cache enabled: no
  NV Cache support power management: No.

  SMART ATTRIBUTES:
  ID Description status worst threshold value TEC gross
  ---------------------------------------------------------------------------------------------------------------------------------------------

  Any ideas what is it?

  I tried to save the patch that HP has pushed out, but I didn't, my system state would be if I did.

  Any ideas?

  Thank you!!

  xzr1tv

  Install the new BIOS F29 with

  Supports the feature of Intel iRST systems

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-124651-1&cc=us&DLC=en&LC=en&OS=4132&product=5328068&sw_lang=

  Intel Management Engine Interface driver

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=CP-124055-1&CC=de&DLC=de&LC=en

  Update the RST

  https://Downloadcenter.Intel.com/SearchResult.aspx?lang=eng

  Chipset

  https://Downloadcenter.Intel.com/Detail_Desc.aspx?AGR=Y&DwnldID=20775&ProdId=816&lang=eng&OSVersion=Windows%208.1 * & DownloadType = drivers

  Check your settings in Bios of RST

• HP ENVY 14-2050se Beats Edition Notebook PC

  Currently, I have acquired the laptop next used:

  HP ENVY 14-2050se Beats Edition Notebook PC
  Serial number: {information}
  Product number: LW398UA

  Someone deleted the recovery files and I need to find a set of recovery disc for this. Y at - it somewhere I can order or download the disks?

  Every other time I boot the system it blue screens, but everything checks very well and he's generally well after the restart of the second time.

  Hello

  You can order a replacement set of recovery discs from the link below.

  Order HP recovery disks.

  If you have a problem with this link, order them directly from HP.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  Kind regards

  DP - K

• HP ENVY 17-2100 3D Edition Notebook PC motherboard

  Hello

  Has anyone idea how the price of the HP ENVY 17-2100 3D Edition Notebook PC motherboard. I intend to change my motherboard because of the problem here. http://h30434.www3.HP.com/T5/notebook-recovery/black-screen-no-BIOS/TD-p/3288555

  Hello astovlBMB,

  I'm sorry to hear that you have problems with the motherboard on your HP Envy 17-2100 3D. According to the Manual on page 20:

  Map of the system (including the 1 GB graphics discrete memory and hardware replacement thermal subsystem):
  Only for models computers equipped with a block to display 3D Part # 630793-001
  For use only with models of computer with a 2D display Assembly part # 630792-00

  Please check HP parts Surfer: http://partsurfer.hp.com/search.aspx for prices and any replaceable components options.

  I hope that was helpful.

  Thank you

• Want 15t_j100 Quad E2E34AV Ed: 10 Windows upgrade failed - blinking display of Envy 15 t-j100 Quad Edition Notebook PC

  Upgrade Windows 10 failed on my Envy 15 t-j100 Quad Edition laptop.

  Symptom after upgrade has been a video exhibition quickly flashing without control of the PC.

  I have to go back to the previous version - Windows 8.1.

  Back with success on Windows 8.1

  Symptoms point to video card problem after updated Windows at level 10.

  My laptop has two, provided by HP online:

  Intel HD 4600 Grapics (internal)

  NVIDIA GeForce GT 740M

  See the research, that Intel and NVIDIA have Windows 10 drivers for these graphics cards.

  Yet immediately when Windows 10 signing after upgrade, the laptop display has been viewed quickly.

  The only way I could get control of the laptop was CTL-ALT-DELETE to start the Task Manager.

  The Task Manager showed that more CPU resources would "host setting synchronization process.

  Called Microsoft Support - they indicate a likely problem with display adapter driver and advised to "go back" and then contact HP support.   called HP Support and they advised to work with Microsoft.  Great!
  
  Would appreciate recommendations on the way forward for Windows 10.

  Dgood43 wrote:
  

  Initially I found the 10.18.13.5324 Rev.A-NVIDIA graphics driver.

  I was allowing the HP site automatically detect my curent - Windows OS 8.1.

  When I manually switched OS Windows 10, I see it listed.

  I also see 10.18.15.4248 that place listed for the Intel HD 4600 graphics card.

  Can I install both of these drivers before you upgrade Windows 10?

  Both are supported on Windows 8.1?

  If so, why HP Support Assistant would not have install me the upgrade?

  Am I missing something here?

  Install only the softpaq grahips from Nvidia. It will allow to install the two drivers.

  When I click on the button 'Download' blue, it offers two choices:

  Use HP download and install the Wizard (recommended)

  Download only

  This is the second option that you recommend when you say to use "usb flash drive support? Yes. Create an installer of Flash 10 Windows usb player. This is the second choice option.

  Thanks again for your help!

• ENVY 15 t-j000 Quad Edition Type of Ram for upgrade

  I try to add a stick of ram to 8 GB for my ENVY 15 t-j000 Quad Edition. Site HP Web does not list the type/size of ram to find the stick of ram suitable for upgrade. If someone knows this information, it would be a great help. Thank you.

  henry_mb wrote:

  I try to add a stick of ram to 8 GB for my ENVY 15 t-j000 Quad Edition. Site HP Web does not list the type/size of ram to find the stick of ram suitable for upgrade. If someone knows this information, it would be a great help. Thank you.

  Hello

  What is the new portable Haswell? This laptop supports modules SODIMM DDR3 1600 MHz, but take a look what original config is. HP uses memory especially two modules config so if there are already 8GB it will be probably 2 x 4 GB modules. I recommend this one:

  http://www.Amazon.com/Corsair-vengeance-laptop-memory-CMSX8GX3M1A1600C10/DP/B0076W9Q4Q/ref=sr_1_3?s=PC&ie=UTF8&QID=1373665809&SR=1-3&keywords=vengeance+SODIMM

• poping and sound crackling with HP ENVY 15 t-j000 Quad Edition Notebook computer Touchsmart

  Hello

  I just got my laptop last week and whenever I listen to music or video, there will be sound poping appears from time to time and it is really annoying. I did a lot of research, but it did not help.

  any help would be much appreciated

  Hello

  I think I found the problem. It is because of the software audio beats. I tried to turn it off, and all sounds jerking went. I have also connected my laptop to other speakers and play with audio on beats, creaking came back. When I turned it off, there is more no jerky sounds, so now I'm sure it's not because of the material in my laptop, but rather the software audio beats

  However, I know that it is just a temporary solution. Think someone can help me?

• When the touch screen will be available to customize the ENVY dv6t-7300 Quad Edition

  I am a customer of long date HP and we ordered that several custom laptops as well as we have in our office workstations.  I have 2 laptops, I am ready to replace, the two dv6t for about 3 years and touchscreen offered then.  I don't want a ultrabook.  I'm in the publishing house and a workaholic must plan the most everything.  I've been periodically check since October and still no touch screen option.  I really want to leave HP, but one of the portable won't last much longer is there an eta or that's going to be a possibility?  With Windows 8, it makes no sense, why it is not currently available.  Thank you very much for your help!

  Please do not worry much about it. HP comes with several touch new innovative, capable, high, elegant setting designed and echonomic models. Please look out for all the products and you will certainly love them.

  There are touch screen active portable computers for the launch of HP in the months 1-2.