HP Envy 4500: Mac running El Capitan will not recognize the HP Envy 4500 printer more

Last week I was able to print to my HP Envy 4500 to my MacBook Air and MacBook Pro, both running El Capitan.  However, when I went to print today, no computer cannot find my printer.

I tried everything I found on these forums of discussion... the network reset, feeding all turned off, turning off iPv6, etc. anything.

I have a USB cord used to print today and when I went in the connected USB printer utility, I could select Configure the wireless, but again, make the message: not accessible device.  It notes the wireless network, the settings were downloaded successfully on my device, however, your Mac could not locate the device on the network.   My Mac is both connected to the same wireless network.

Help!

Advertisement

Hello

I restart your Mac and try the above steps again - if it does not prove successful, I then reboot your router and repeat the steps.

Tags: HP Printers

Similar Questions

  • HP dv7 will not recognize the second hard drive

    My HP dv7-2185dx running Windows 7 will not recognize the second hard drive, bios recognizes this Intel Rapid storage acknowledges.

    Main hard drive is a 1 to install a second hard drive to 500 GB.

    Hello

    Try the following.

    Judgment of the laptop and unplug the 2nd HARD drive.

    Robinet tap away at the key esc that you start the computer to launch the Start Menu, and then select f10 to open the bios menu.  Press f5 to load the default values (sometimes it's f9, but the menu below indicates the correct key), use the arrow keys to select 'Yes' and press ENTER.  Press f10 to save the setting and still use the arrow keys to select 'Yes' and press on enter.

    When windows has reloaded, download and reinstall the Chipset driver at the following link.

    Chipset Driver - Windows 7.

    When this is finished, stop the laptop.

    Reconnect the 2nd HARD drive, then start Notepad and let Windows take over completely for a few minutes before checking if the reader appears in the lower part of the disk management window.

    Kind regards

    DP - K

  • Time capsule will not recognize the backup from another mac

    Time machine will not recognize the backup from another mac

    Time Machine will never find "another" Mac backups unless you've been backup that 'different' Mac on the same Capsule you have there.

    So, we need more information and to try to understand what it is that you are trying to accomplish. Please assume that we know nothing about what you could have done in the past... (since we don't have).

  • Serial number problem: I am installing Lightroom 4 on my Mac, but the Adobe web site will not recognize the 18 digit serial number.  He wants more.  What to do next?

    I try to install 4 Lightshop on my Mac, but the process of license Adobe will not recognize the 18 digit serial number.  What should I do next?

    Adobe has no set of 18 digits.  It is perhaps a number of redemption.

    your serial number is a 24 digit number composed of 6 groups of 4 numbers, find the serial number of your product Adobe quickly

  • My laptop that is running windows xp does not recognize the computers on the network running windows 7. Any advice?

    I recently created my home network again.  It consists of a laptop running windows 7 Professional 64 b, b Office windows 7 Professional 32 running and a netbook under windows xp home.  Two computers running windows 7 recognize each other and share correctly, but the netbook will not recognize the other computers on the network at all.  They can see it, but then say they can't access them when you are trying to access.  They are all on the same workgroup.  Computers that run windows 7 discovered the network, file and printer sharing, and public folder sharing all lit.  Password sharing is disabled and windows manages the homegroup connections.  Any advice would be appreciated, I need to use computer dvd players 7 on the network to install some things on the netbook.

    Hi mahmorc,

    ·         You get the error message?

    Follow these methods.

    Method 1: Follow the steps in the article.

    How to troubleshoot a network home in Windows XP

    http://support.Microsoft.com/kb/308007

    Method 2: Perform a clean boot to see if there is a conflict of software like the clean boot helps eliminate software conflicts.

    How to configure Windows XP to start in a "clean boot" State

    http://support.Microsoft.com/kb/310353

    Note: After the boot minimum troubleshooting steps, follow section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

    After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

    (a) click Start and then click Run.

    (b) type msconfig and click OK.

    (c) the System Configuration Utility dialog box appears.

    (d) click the general tab, click Normal Startup - load all services and device drivers and then click OK.

    (e) when you are prompted, click on restart to restart the computer.

    Method 3: Update the latest drivers for the network card.

    How to manage devices in Windows XP

    http://support.Microsoft.com/kb/283658

  • Have you installed the printer & software driver... will not recognize the installation of the scanner or Nikon camera to download photos... What can I do?

    Have you installed the printer & software driver... will not recognize the installation of the scanner or Nikon camera to download photos... What can I do?

    The duplicate thread information:

    Cannot connect Epson scanner/Nikon camera to printer!

    Hi Carolyn has Culp,


    Thanks for asking this question to Microsoft Community!

    I understand that your scanner and Nikon camera is not getting recognized in windows vista.

    He would be grateful if you could answer these questions. This will help us to a better way to get a resolution of the issue.
    1. have you made changes on the computer before this problem?
    2. What is the brand and model of the scanner?
    3. are you an error message or error code?
    4. is that your other USB devices work?
    I would suggest trying the following methods and check if it helps.

    Method 1:

    Try connecting to another USB port and check if the camera is detected or try to plug the camera on another computer.
    Method 2:
     
    Hardware devices do not work or are not detected in Windows: http://support.microsoft.com/mats/hardware_device_problems/en-us
    Method 3:
     
    Remove and reinstall all USB controllers.
    To remove and reinstall all USB controllers, follow these steps:
    (a) click Start, run, type sysdm.cpl in the Open box, and then click OK.
    (b) click on the Hardware tab.
    (c) click the Device Manager button.
    (d) expand Bus USB controllers.
    (e) right click on each device under the Bus USB controllers node and then click on uninstall to remove them one at a time.
    (f) restart the computer and reinstall the USB controllers.
    (g) connect the removable USB storage device and perform a test to ensure that the problem is solved.

    Method 4:
    To update the chipset drivers and check if it helps.

    Reference:
    The problems of scanning: http://windows.microsoft.com/is-IS/windows-vista/Troubleshoot-scanning-problems

    It will be useful. For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you.

  • Windows 7 will not recognize the dvd drive

    Windows 7 will not recognize the dvd drive, although it worked well for more than two years.  Now I can't access it to install new software.

    It will not be displayed in the Device Manager, bad shooters to say it is not connected or is, tried Fixit fix (could not as "not applicable to your computer update"), uninstall iTunes (in the case of a conflict - even if it worked with the DVD of > 1 year), etc., but still cannot access the DVD.

    It's obviously a known issue, given that a support page - http://support.microsoft.com/kb/976187 that recommends the fix or manually disable ALPM active power management.  If it of a known issue, why is not included in the updates and that I have to disable ALPM power if management it worked ok before?

    What now? Is turn off the power, my only option?  What happens if it is not yet recognized after that?

    Hello

    If the drive is viable:

    Follow these steps to remove corruption and missing/damaged file system repair or replacement.

    Start - type in the search box - find CMD top - RIGHT CLICK – RUN AS ADMIN

    sfc/scannow

    How to fix the system files of Windows 7 with the System File Checker
    http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

    Then run checkdisk (chkdsk).

    How to run check disk in Windows 7
    http://www.SevenForums.com/tutorials/433-disk-check.html

    ==========================================================

    After the foregoing:

    References to Vista also apply to Windows 7.

    Step 1: Please do all the same underneath if you did some before as is often total
    a process that solves the problem.

    Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
    Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
    RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
    below.

    Then, work your way through these - don't forget the drive might be bad, could be a coward
    cable or slight corrosion on the contacts (usually for a laptop) and other issues.

    Your CD or DVD drive is missing or is not recognized by Windows or other programs
    http://support.microsoft.com/kb/314060 - a Mr Fixit

    Try this fix manually if the Fixit 314060 does not work
    http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

    Your CD or DVD drive is missing or is not recognized by Windows or other programs-
    a Mr Fixit
    http://support.Microsoft.com/kb/982116

    The DVD player does not work after installing Windows 7
    http://support.Microsoft.com/kb/975270/

    The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
    Windows Vista
    http://support.Microsoft.com/kb/929461

    When you insert a CD or a DVD, Windows Vista may not recognize the disc
    http://support.Microsoft.com/kb/939052

    Your CD or DVD drive cannot read or write media - A Mr Fixit
    http://support.Microsoft.com/GP/cd_dvd_drive_problems

    CD/DVD drive does not appear in Windows Vista, or you receive this error during Windows Vista
    Setup after booting from the DVD (AHCI)
    http://support.Microsoft.com/kb/952951


    Drive CD - R or CD - RW Drive is not recognized as a recordable device
    http://support.Microsoft.com/kb/316529/

    Hardware devices not detected or not working - A Mr Fixit
    http://support.Microsoft.com/GP/hardware_device_problems

    Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
    ends. Remove and replace, do not just tight. For laptops, you can often clean power and
    contacts data with a pencil eraser.

    Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
    manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

    ===============================

    Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
    Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
    do it right.

    Did you follow the Troubleshooting Guide for the reader who still does not work? There are
    the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

    Check with your Maker system and a device for the two possible firmware updates and the
    correct registry entries for your car.

    Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
    as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
    the parameters.

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

    -----------------------------------------------------------------------

    You can probably find more info here and maybe even the exact registry settings for your
    CD/DVD drive someone with the same model.

    Forums - a lot of expert real help
    http://Club.myce.com/

    CD/DVD units
    http://www.myce.com/storage/

    Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
    nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

    DevManView - free - an alternative to the standard Windows Device Manager, which displays
    all devices and their properties in flat table, instead of the tree viewer
    http://www.NirSoft.NET/utils/device_manager_view.html

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

  • Trying to install Adobe Creative Suite 5 Design Premium, but will not recognize the serial number?

    I am trying to install Adobe Creative Suite 5 Design Premium on a PC but will not recognize the serial number? What should I do?

    I also have Adobe Acrobat 9 on my Mac and it is now saying that I have to throw "Adobe Photoshop Creative Suite 5 Design Premium". When I do that nothing happens with Acrobat 9, and it closes. I tried to reinstall the disk without success.  What should I do?

    Invalid License http://helpx.adobe.com/creative-suite/kb/error-serial-number-valid-product.html

    -http://helpx.adobe.com/creative-suite/kb/invalid-serial-number-cs4.html

    - and http://forums.adobe.com/thread/1038761

    Given that Adobe can't CS5, I think that above, is what it is

  • I lost my WiFi signal after having placed a time Capsule in the system. Now the Airport Extreme will not recognize the system. Any ideas?

    Any ideas on why my Airport Extreme will not recognize the system after the integration of the time Capsule in my system? Continues to have a flashing yellow light after trying all suggestions of technicians from the Apple Store and Internet provider.

    Since we don't know all what has been tried, we will have to start from the beginning if you don't mind.

    What exact models are your AirPort Extreme and Time Capsule? What is the brand and model of your modem Internet? I'll assume that Extreme is your "main" router and is directly connected to the modem by Ethernet... correct?

    Do you have the Time Capsule (TC) connected to the extreme, by wire or wireless? What is your goal for the TC? In other words, will not be used to extend the reach of the extreme wireless?

  • Fuze 4 GB will not recognize the change of information tracking

    Right then, I had some problems with my Fuze MP3 player. When I download the new music on the device, the ID3 tags all come out the way they are supposed to. However, if I remove the music that is on the drive and replace it with the same tracks with ID3s update, it will not recognize the change of title, album, or artist, if the song file will be updated. I know because I had problems with the songs with the same name or accidentally given songs the name of another song, which resulted in incorrectly labeled music.

    I tried to format the drive, I tried to remove the music manually in the file system, I tried to change the USB mode and delete the file that I said holds the ID3 data, and I tried all the possible permutations of disconnection and let the Player recognizes the changes. This includes the removal of all the music in the player, disconnection of the latter, confirming that there is no music on the system, to change the USB mode, deleting the file with the ID3 information, turning the rear USB mode, reconnect, put my music on the device, and the problems have not been resolved.

    It is likely, it is just to be fickety, and there is something I'm don't is not right, but it's the second "rocket" I've owned - I love the model and went up to return a Fuze + in favour of the former model - and one has never had this problem. I'm willing to try anything within reason to solve the problem, so I hope someone can point me in the right direction.

    In fact, the problem was not as expected at all. I think it turns the problem is Windows Media Player, which I only use to sync my music on my MP3 player, had a library with outdated information. So after the Player update multimedia, I refreshed my library recordings and everything worked as you wish. I just to make sure that if I make changes to existing songs in my library.

    Thanks for all the help, guys, guess it was on my end.

  • Try to burn a CD. The system will not recognize the blank disc or let me burn__

    Try to burn a CD. The system will not recognize the blank disc or let me burn... says there is no disc inserted

    Hello

    Have you tried to close all programs and then insert the disc? Restart the 1st and then try it.

    If no joy:

    Please make all below even if you have done some before as it is often the set of operations which solves
    the question.

    Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
    Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
    This will refresh the default driver stack. Even if the reader does not appear to continue below.

    Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
    slight corrosion on the contacts (usually for a laptop) and other issues.

    Your CD or DVD drive is missing or is not recognized by Windows or other programs
    http://support.microsoft.com/kb/314060 - a Mr Fixit

    The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
    http://support.Microsoft.com/kb/929461

    When you insert a CD or a DVD, Windows Vista may not recognize the disc
    http://support.Microsoft.com/kb/939052

    Your CD or DVD drive cannot read or write media - A Mr Fixit
    http://support.Microsoft.com/GP/cd_dvd_drive_problems

    CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
    http://support.Microsoft.com/kb/952951
    Drive CD - R or CD - RW Drive is not recognized as a recordable device
    http://support.Microsoft.com/kb/316529/

    Hardware devices not detected or not working - A Mr Fixit
    http://support.Microsoft.com/GP/hardware_device_problems

    Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
    ends. Remove and replace, do not just tight. For laptops, you can often clean power and
    contacts data with a pencil eraser.

    Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
    manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

    Hope these helps.

    Rob - bicycle - Mark Twain said it is good.

  • Win 7 64 bit computer will not recognize the old jpg files since 2003 of the records that have been transferred to an external hard drive.

    Win 7 64 bit computer will not recognize the old JPGs from three 2003 files that were transferred to an external hard drive...  File appears in the directory but with no thumbnails icon. Does not open in the Viewer, Picassa, Ifranview, paint, PhotoShop.  I get conflicting messages... invalid image (Windows Viewer)... Unknown file format (IfranView)... Access has been denied (painting), a blank image (Photoshop),... You are not allowed to open this file (Picassa).

    Creation 2007
    Last updated on 2003
    2010
    Any help would be appreciated.

    Mahalo,

    Philippe

    Ran the Scan, the system is secure.

    I was able to bypass stubborn files to transfer them to a flash drive and copy them to another folder.  I was then able to access.  Somehow I messed up the permissions in the previous transfers of old machines and OS.

    Thank you for your help and attention.

    Mahalo,

    Philippe

  • Windows will not recognize the password

    I have reset the password using windows live reset option, but now my laptop will not accept the password and I am more able to access the laptop at all. I don't know what else to do. Help, please.

    If you change the Windows through Microsoft Account password online, it will update when you connected to the internet via your computer and when the PC is turned off or disconnected from the internet, you need to use your old password.

  • Good night! I will not renew the license of creativ-cloud more

    Good night! I will not renew the license of creativ-cloud more

    If you have a full creative cloud plan, one App or photography to the month then please see cancel your subscription or membership. Creative cloud for more information on how to cancel your subscription page to manage account.

    If you have an annual plan of complete creative cloud, one App or photography and wish to cancel your membership then please contact our support team directly.

    If you have a full creative plan Cloud, one App or photography monthly or annual and are located in a country listed here then contact our team of assistance directly to update your member status.

  • I uninstalled flash on my mac now youtube videos will not play. the error says safari does not recognize the video formats available.

    I uninstalled flash on my mac now youtube videos will not play.

    the error says safari does not recognize the video formats available.

    Reinstall the Flash Player... Why did you remove it?

    Barry

Maybe you are looking for


HashFlare