HP LaserJet 3030 all-in-One printer range

Similar Questions

• HP laserjet 3030 all-in-one prints only odd characters now that it is connected to parallel cable.

  I have a printer HP laserjet 3030 all-in-one that has worked very well, but the connector broken so I bought a USB2.00 for parallel printer cable pre-mounted to my laptop (I use windows 7) It only prints the weird characters! Help, please.

  I change some settings? I still have the original disc. I hope that this is not a lost cause!

  Hello

  Welcome to the Microsoft community.

  I understand that you are facing the question about printing.

  I will definitely help you with this.

  Have you tried to print the different document?

  I suggest you go through the below methods:

  Method 1: Try to run the printer Troubleshooter:

  1. Press Windows + R key.

  2. Type of Panel, and press ENTER.

  3. Click on troubleshooting.

  4. In the left pane, click View all.

  5. In the list, click the printer and run the troubleshooter.

  Method 2: Try the clean boot:

  A clean boot is executed to start Windows by using a minimal set of drivers and startup programs. This will eliminate the conflicts of software that occur when you install a program or an update or when you run a program in 8.1 of Windows, Windows 8, Windows 7, or Windows Vista. You can also troubleshoot or determine what conflict is causing the problem by performing a clean boot.

  How to perform a clean boot in Windows

  http://support.Microsoft.com/kb/929135

  Note: See "how to reset the computer to start normally after a boot minimum troubleshooting" to prepare the computer to start as usual after a repair.

  I hope this helps. Please post back with the State of the question and we will be happy to help you further.

• Problem with scanning with Laserjet M1212nf all-in-one printer network

  I installed the drivers for my Laserjet M1212nf connected on my computer laptop 64 bit of Windows 7, but it seems like just a printer (in devices and printers). I can't scan from the laptop (I get the error "no TWAIN Device Installed").

  The figure (and work) scan function if I connect to the printer via the USB port and install these drivers, but my laptop does not usually reside in the same room as the printer.

  The scan function installs and runs correctly on a Windows XP desktop computer also connected to my network.

  Hi CW_Enloe

  I will try this tool

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?cc=us&LC=en&JumpID=ex_r4155/en/HHO/IPG/easy_wireless/network_diag/&lang=en&softwareitem=MP-96434-1

  If that doesn't help not please inlcude the model of the router you use (be sure that the router is running the latest firmware) which can help was good.

  It can be useful;

  RobertoR

• LaserJet pro m127 fn: impossible to analyze by using HP all-in - One Printer Remote android app.

  Hello

  I use Hp all-in-One Printer Remote android app, Print function works fine but scanning works nor on my phone (4.4 KitKat) or Tablet (jelly bean 4.1).

  analysis function works by using my laptop (Windows 7)

  Help, please.

  Hi @EslamHassan

  Welcome to the Forums of HP's Support. I think that you have a question about the HP all-in-One Printer Remote app.

  The LaserJet M127fw printer is not a printer supported for the HP AiO application. I have included the HP printers and Mobile Printing Solutions support document for reference.

• Software all-in-one printer HP LaserJet Pro CM1415nfw does not load

  Software solution complete all-in-one printer HP LaserJet Pro CM1415nfw (CD or download) does not correctly load on my desktop running Windows 7 Professional 64 Bit. After I bypass payment the contract of the software, loading software hangs on the 70% mark and I get the following message:

  "Error message: a problem occurred during the preparation install the software." If please restart your computer and run this installer again. If the problem persists, please visit the web site of product support for your product. MSIExec command: /i "C\CM1410_MFP_Series Solution\Setup\Core\SIPM_64 based |" HpTcpMon64.msi"/qn REBOOT = ReallySuppress Path: return code: 1603"

  The CD software did load on my laptop which runs on Windows XP, SP - 3.3 and the printer works as expected.

  Uninstall other software printer and disconnect them. Then try to load the new software first.

• All-in-one printer, HP Photosmart C6280 range

  cabnot use black ink only or auto duplrx options

  Hello

  You should check with the help of HP, their documentation online, drivers, diagnostics and ask in their forums.

  Support HP & drivers
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  ========

  HP Photosmart C6280 all-in-One Printer - Support
  http://h10025.www1.HP.com/ewfrf/wc/product?product=3194498&LC=en&cc=us&DLC=en&lang=en&cc=us

  HP Photosmart C6280 all-in-One Printer - drivers and software
  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?product=3194498&LC=en&cc=us&DLC=en&lang=en&cc=us

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• E-all-in-one printer, HP Photosmart 6520 range

  Can HP Photosmart 6520 e-all-in-one printer be "plugged in" to a tower instead of running wireless? We use this printer as a local printer only.

  You can use a printer USB cable to connect it to your computer.

• all-in-one printer, HP Officejet 4315xi range & hp Pavilion with Windows 7

  Printer has said he is ready and he is printing of the document that I send to print, but nothing happens. does not print.  I ran troubleshooting program.  Have tried everything I know without success.  Can you help me?
  Thank you

  Hello

  As OEM HP is responsible for the good operation of the printer and their
  drivers provided. Check with HP support, their documentation online and
  drivers and ask in their forums.

  Good luck, you need to update or reinstall the latest driver.

  HP Officejet 4315xi all-in-One Printer - drivers<- set="" to="" your="" version="" of="">
  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?product=1138347&LC=en&cc=us&DLC=en&lang=en&cc=us

  HP Officejet 4315xi all-in - One Printer - support and troubleshooting
  http://h10025.www1.HP.com/ewfrf/wc/product?product=1138347&LC=en&cc=us&DLC=en&lang=en&cc=us

  HP support/troubleshooting & drivers
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  =============================================

  The main issue is probably the drivers, but these can help:

  Add or remove a printer
  http://Windows.Microsoft.com/en-us/Windows-Vista/add-or-remove-a-printer

  Solve printer problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  Open the printer Troubleshooter
  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  Find the manufacturer's Web site
  http://Windows.Microsoft.com/en-us/Windows-Vista/find-a-printer-manufacturers-website

  Find and install printer drivers in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/find-and-install-printer-drivers

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• HP Photosmart 5520 All in One printer cancels an order of copy of the glass

  HP Photosmart 5520 All in One printer & HP Pavilion dm1 Notebook PC

  I put a document on the glass of the printer to make a copy. The command is recognized, but cancelled immediately. The first two attempts were given a bit of text/photo about 1 centimeter.

  I used the doctor scanning HP and installed my printer again, but that has not helped.

  RodeDraak

  Hi RodeDraak,

  Given that the problem occurs when you run a copy, I hope that the problem is the printer hardware not the software on the computer.

  You have the printer connected directly to a wall outlet or is this a surge protector or power bar? Even if you have used a surge protector/power bar this whole time and you feel that this is not the case, please connect to a wall outlet so that we can eliminate the source of energy as the primary cause.

  Issues when connected to an uninterruptible power supply/Strip/surge protector power

  In this document, you will see,

  QUESTION:

  Questions or problems may arise when a HP LaserJet printer is connected to a UPS (UPS), a power strip or a surge protector

• My HP LaserJet 3055 All In One does not scan with Windows 7-64 bit.

  My HP LaserJet 3055 All In One does not scan with Windows 7-64 bit. I can copy and print only. Thank you.

  Hello

  Is the printer connected to your PC by USB or network?

  Using the USB connection, you can scan using Windows Fax and Scan software built into your operating system.

  Scanning over a network connection unfortunately supported on Windows7 32 bit only, as you can find listed in the section about network scanning below:

  http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?&objectID=c02539136#A2

  Kind regards

  Shlomi

• 4630 HP e-all-in-one printer cartridge change

  Recently bought a HP 4630 e-all-in-one printer. When the black cartridge needed evolution for the first time I have been unable to get printing to work again.  It displays the message «the following ink cartridges need to be replaced...» "followed by a symbol of glass side means time.  I replaced both black and color cartridges, and they are both the correct number (61) for the printer.  No help available?

  Hi john1936,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  Sorry to hear that you are having problems with the printer and ink cartridges.  I have found a document that will resolve this problem. Please note that the title of the document does not list the error you have however it will solve the problem at hand.

  Please click on the following link that deals with a "missing cartridge", 'cartridge problem,' or "not compatible ink cartridges" Error Message is displayed on the control panel.

  I suggest also that if you have the printer power cable connected to a bar/power strip, please remove and connect it directly to a wall outlet. Here is a document that explains the problems when connected to an uninterruptible power supply/Strip/surge protector power.  This document is generally for HP products even if a LaserJet printer for example the cottage.

  Please do not hesitate to write again for any further assistance.

  Thank you for your time.

• HP LaserJet M1319f all-in-one is not compatible with Windows7 install error

  I can't get my MFP HP LaserJet M1319f all-in-One (Nr - CB536A) to install correctly.  I just bought a new laptop with Windows 7 and the printer says that it is not compatible.  Whenever I put the disc in, and then click intall a message comes up saying "the installation software is not supported on this OS, or the system does not satisfy the minimum requirements for installing this software.  Please see the specifications of the product. "I tried to download drivers but it did not help, maybe I just didn't make the right one.  In any case, I could really use some help.

  My OS is Windows 7 64 bit.

  Please send a response to {deleted personal information}.  I'm not really familiar with this forum stuff and so do not know how to find the answers posted there.  Thank you.

  Hello

  You can download the drivers for plug-and-play basis for 64-bit Win 7 driver for the printer m1319 on hp.com. The link below you will be:

  M1319 Win7 64 bit on hp.com printer driver

  Here is a document that should help with the installation of the printer with the Win7 OS:

  Win 7 install using the USB cable

  Please let me know if you need help more with this problem.

• convert a hp 3030 all in one windows xp to windows 7

  I have a HP 3030 all-in-one which has been set up on a Windows XP laptop.  I want to move it to a HP 64 bit multi core desktop, which works in Windows 7.   Several times I tired to download many of the drivers offered on the site of HP.   The drivers start to load but cling and not ends.  Loading comes to the installation of message and just stays there.   I even let alone more nite to see if she would charge.   On the XP laptop, I was using the 3030 PLC6 driver.   I tired to load the driver for PLC6 from the Windows 7 machine but it crashes just as described above.

  I also want to load software box HP tool provided for laptop XP on the Windows 7 machine so that I can scan and fax.  Any ideas how to do this?

  Thank you

  CD3

  Hi cd3,.

  It is a product of the profit margin. For the best answer to your questions, you need to transfer your question at the following links.

  http://h30499.www3.HP.com/T5/business-support-forums/CT-p/business-support

  http://h30499.www3.HP.com/T5/printers-LaserJet/BD-p/BSC-413

• HP Deskjet Ink Advantage 1515: stop the test page printed for all-in-one printer, HP Deskjet Ink Advantage 1515

  How can I stop my HP Deskjet Ink Advantage 1515 all-in-One printer to print a test page everytime I STARTED printing?

  Hello JoshSimon ,

  Welcome to the HP Forums.

  I see that you have a problem with the printer printing before you print a test page.

  If you turn off the printer at the end of the day, please do not.  Turn the printer on/off will result in printing a test page.  If you are concerned about the printer lost power, and that's why you stop, the unit actually built in sleep/stand mode that will kick in when you are not using the printer.

  Once a print job is sent to the printer it then wake up and do the task at hand.

  In addition, make sure you have the printer power cable connected directly to a wall outlet and not a bar/power strip. Here is a document that uses a LaserJet printer for example, but it is intended for HP products in general. Please click the link which explains the problems when connected to an uninterruptible power supply/Strip/surge protector power.

  If troubleshooting doesn't help not solve your problem, then I would say call the HP Technical Support to see all the other possibilities for you. If you call in North America, the number is 1-800-474-6836 and for all other regions, please click here: click here.

  See you soon,.

• Printing error 0 x 00000709 when I try to make my new HP Officejet e-all-in-one printer default

  Print 0 printer error x 00000709 when I try to make my new HP Officejet e-all-in-one printer default.  I removed the old printer, uninstalled it, theinstalled HP Officejet (former was an HP Photosmart all-in-one).  I rebooted, everything I can think of.  I spent hours (overnight) through countless services for troubleshooting.  Can someone help me please?  Need of college courses

  . From Internet Explorer

  Original title: error printer print 0 x 00000709

  Hi PattiVan,

  It seems that you can not set HP Officejet 4620 as default printer, you get the error message: 0 x 00000709.
  
  What is a local printer or network printer?
   
  We will try the following methods and check if they helps us to solve the problem.

  Method 1: Try to change the default printer value in the registry key and check if it helps.
  

  Registry WARNING: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, see this link: http://windows.microsoft.com/en-US/windows7/Back-up-the-registry

  (a) click Start.

  (b) type regedit in start search and press enter.
  (c) access the site mentioned below.

  HKEY_CURRENT_USER\Software\Microsoft\Windows NT\CurrentVersion\Windows
  (d) in the right column, you will find key device, change the value of your printer name.
  (e) it is for example in the format: "HP LaserJet 4250 PCL6, winspool, Ne03:

  (f) right click on the value and click Rename, replace with the name of your printer.
  
  Method 2: Try the steps from the link.
  Printer in Windows problems
  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Method 3: Let's connect on another user account and check if you can configure the printer as the default printer.

  If it works in a different user account, then the user account is damaged.

  
  

  Refer to this link and create a new user account, copy files to the new user profile

  http://Windows.Microsoft.com/en-us/Windows7/fix-a-corrupted-user-profile

  I hope this helps!