Similar Questions

• Shows HP LaserJet 3330 horizontal lines exactly each 1.5 "when you print a completely blank page

  HP LaserJet 3330 shows seven or eight approximately 3.5 "cloudy horizontal lines spaced exactly each 1.5" even when you print a completely white page. This also happens when copy and fax.

  There are also 2 very thin vertical lines running down the entire page about in the middle. They are exactly 1 "apart.

  However, a scan of a blank page on my computer (not printed) is perfectly clean.

  Windows 7. No change or upgrade.

  Propbably the toner cartridge, if they are 1.48 "apart that it could be the cylinder in the process of development or the charge roll who are both in the toner cartridge. So a good assumption if you replace the toner cartridge, the problem will disappear. Vertical lines could also be part of this issue.

• Download Windows 8.1 LaserJet 3330 MFP software

  I tried to use it with the 3330 CD to install the software on my computer.  It-error, where can a download of HP software to use all the features introduced with Windows 8.1?

  The only factor which is available for this printer is the driver update in windows/OS. This will give you a basic printing functionality only for windows 8 and 8.1.

  Scan Windows 8.1 options include: fax and scanning, Microsofts built in scan app, HP Scan and Capture app or HP all-in - One Remote app Windows. The Windows Fax and Scan and Microsofts built in app scan are on the screen of the subway under the apps for all section. HP and Capture app and HP All-- scanning in One Remote app can be downloaded from the store or is already on the screen of the subway. I have not tested this printer with these options so not sure if one of these will be options analysis but these documents are available.

• All-in-one printer, HP LaserJet 3330 make it compatible with windows 7?

  Is it possible to make my old HP 3330 printer fully compatible with my Vista laptop running?

  Is it possible to make my old HP 3330 printer fully compatible with my new Windows 7, home premium running office?

  Thanks, JB

  Contact HP support or start here (assuming that Win7 64 bit): http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=us&prodNameId=72628&prodTypeId=18972&prodSeriesId=66359&swLang=8&taskId=135&swEnvOID=4063

• Windows 7 64 bit, hp laserjet 3330

  printers HP 3300 pcl 5 works, but won/t printing from the computer.

  Have you checked the cables etc.?
  The printer is compatible with Windows 7?

  After checking the above and if the printer still does not, check with HP about what could be the cause of the problem.

  TaurArian [MVP] 2005-2010 - Update Services

• "windows cannot find a driver" in the installation package?

  We have a file server and print XP on our network that has a printer Series PCL LaserJet 3330 installed 5th (using the original installation CD and prints from the XP Server). While trying to install the printer on a remote computer, I downloaded the driver package Windows 7 64 bit for the printer on the computer remote and got the error: «Windows cannot find a driver...» "(I don't understand why the pilot was not as it should be in the installation package.) After getting this error - several times, including the re - download the package and re - try - I downloaded the XP Server installation package and I changed the printer driver it as a package to install downloaded for XP. We always get the same error. The installation of the printer worked fine before having to redo our BONES. Anyone know this problem and can help with this?

  This issue is between 64 bit and 32 bit, and there is an easy solution. Once you get back to the way it was before you downloaded the 64-bit package that you go to the machine that you want to load the printer and the printer as a local printer using load say lpt1 port. Auto not detect or print a test page and just finished the installation. Now on the windows 7 computer to join devices and printers and right click on the printer icon and scroll the properties first and left click. Go to the ports, and then add the port and in the box that comes up to put in the name of printserver and the share name of the printer by using the syntax \\printserver\sharename how save and apply and this computer will now be able to print to the printer.

• redirect the output of the printer port LPT1 of COM4_001

  Cannot print
  reboot printer error: "printer not connected or off voltage.»  previously worked.
  Port indicates com4_001
  Wouldn't be LPT1?

  XP SP1
  HP LaserJet 3330 connected by parallel cable (not usb) via a switch 4 ports mechanical

  Hope not delete printer and then reinstall with the cd oem that cannot find the cd after mutation.

  Hello Gdeuce,

  Thank you for your message.  You shouldn't need an OEM CD, but do not remove your printer and reinstall that something may be damaged.  Click HERE to download the latest driver for your device.
  See you soon

  Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• Is HP Document Manager does not work in Windows 7

  Installed HP Laserjet 3330 Document Manager.  Through install correctly and at the end, he advises to reboot the computer.  During the reboot, a message appears "finish install Document Manager" print a test page, and then the error box appears that it cannot find the device, even if the printer is connected via USB and did print a test page.  Whenever the computer is started now the same thing is happening ("" " Finishing installation of Document Manager" print a test page, and then the error box appears that it cannot find the device, even if the printer is connected via USB and did print a test page.) I am able to print from programs, but cannot fax or scan of the HP Document Manager. Checked the HP site and there is no update for this program.  There are solutions to this problem?

  Thanks for the reply Suresh.  I was previously using the Document Manager in XP Service Pack 2.
  I did try a reinstall using the XP compatibility mode and the results are the same as above.

  I'll try the HP forums and see if I can find something in there.

  Doug

• Printer Driver HP LaserJet 6 p file

  I'll try to find a driver file for my HP LaserJet 6 p printer, it worked great until I upgraded to MAC OS Sierra

  Thank you for your help

  Try to configure your printer according to this instruction, the problems of printer on your Mac - Apple Support

• My hp LaserJet 1022nw fails to analyze the download of the printer driver after that macOS Sierra upgraded.

  After switching to macOS Sierra, my printer (hp LaserJet 1022nw) WiFi does not print work orders, even if the printer seems to be to receive the order of work and how to complete it in the work queue.  Connect the printer to my MacBook Pro via USB, I am able to print without problem.  Other computers on the network continue to be able to print wireless.  When I connect via USB and try to scan a updated driver, download cause analysis a software fault message.  Any ideas on how I could proceed to continue to connect and use my printer wireless with the new OS?  The 1022nw is detectable as a printer available (wi - fi) and can normally be added to the list of printers, but doesn't have the print queue even thought that they seem to have been dealt with, and then disappear from the queue.

  Open System Preferences > Printers and Scanners and select the print tab.

  Then the right or control click on the printer on the left then click: reset the printing system

• How can I connect my iMac for HP Laserjet CP2025 El captain

  Connection to HP Laserjet CP2025

  Just replaced my printer laser jet CP2025 with a replacement from eBay (given that it works!)  Previously used one daily for a few years without problem, it of the same model but keeps saying printer idle or not connected, even if it has been folded and selected on the screen.  So, I deleted all of the printers in my preferences that I had amassed 6 different printers and use only 2 BUT now cannot add any back? I use OSX El Capitan on an iMac 2013 end suggestions would be appreciated

  This article should help you to solve the problems of printer on your Mac - Apple Support

• I need the Hp Laserjet M2727nf Hp scanning software

  Need a Hp Laserjet M2727nf Hp scanning software

  You really have a classic Mac, a very old machine now.

• HP Color Laserjet: HP Color LaserJet - lines/stripes

  Hello

  I have a HP color LaserJet and I get a lot of lines and streaks on my printed pages.

  I also note toner inside the printer and my printer seems to take cleaning cycles more than before.

  Thank you!

  Although I work for HP, my posts are MY opinion and not those of HP.

  I would recommend some of the things

  First of all, make sure that your firmware is up-to-date, go to the page software and drivers on HP.com download and install the latest firmware available for the printer.

  Then, make sure that the toner collection unit is not complete

  Finally, print a cleaning of the control panel of the printer page, normally, you should select the following text in the menu:

  • Maintenance of the unit
  • Calibration / cleaning
  • Cleaning page

  You can also view this document as well.

  HP Color LaserJet Enterprise M552, M553 and MFP M577 - lines/stripes, toner and cleaning cycles dust excessive

  Hope that helps.

• Color LaserJet M277dw MFP: Cartridge not recognized after HP recently updated.

  I can use WIndows 10 if the fix is available for this OS.

  I recently updated my HP LaserJet, and after the update, he refused to print, scan or copy. The error message on the display says: "Cartridge not recognized" and it has a large image of the yellow and black cartridge, cyan and magenta those smaller, but below. The printer has a wireless connection to internet.

  Any help would be greatly appreciated.

  Thank you

  Hello

  Install the following firmware for your printer, and then look for a difference:

  http://support.HP.com/us-en/drivers/selfservice/swdetails/HP-Color-LaserJet-MFP-M277-series/7089945/model/7089949/swItemId/kJ-149905-2

  Kind regards

  Shlomi

• Color LaserJet MFP M477fdn Pro: M477 Software Installation fails at 99%

  Like others who have posted here, I have been unable to get the printer software to complete the installation. The printer is a Color LaserJet Pro MFP M477fdn, 3 months. I'm trying to install the software on a new workstation HP Z240 performing Windows 10 (64-bit). The connection is via USB cable. The printer and the software have been previously used with a Windows 7 machine without problem.

  I tried, repeatedly, to install the software from the disc supplied with the printer and also a 126.6 mb download HP Color LaserJet MFP printer M477 Pro series full software and drivers. The results are the same with a source - installation apparently progresses up to connect it the indicator product of progression from screen reached 99%, how it gives an error message "a Setup operation took too long to run. It is a fatal error, preventing the use of the product. Restart your computer and run this installer again. If the problem persists, please visit the web site of product support for your product. "It takes about 20 minutes for the phase of installation to go from 0 to 99%, and then later hooked up to 99% for 2-5 minutes, the error message is displayed.

  I am able to print to this printer, but at least do not have the ability to scan from the computer there is no indication that the I.R.I.S. OCR software is installed.

  I had care of do not connect USB until you are educated.

  I tried repeating the installation without uninstalling first and get the same result.

  I used the uninstall contained the disk feature, and have deleted the printer to the computer using the Panel between the installation attempts.

  I tried to do a right click to run the installer as administrator and get the same result.

  I tried to install after clean boots with turned off Windows Firewall and all functions of the software Norton Internet Security including its function of firewall turned off.

  The event viewer displays none error entry at all and no entry identifies HP as the source of an event.

  I tried to connect via USB 2.0 and 3.0 ports.

  I cleaned recycle them and temporary folders.

  I have updated the firmware of the printer to the 20160331 version.

  Printed printer configuration report will not display any errors, nor that the printer itself indicates something is wrong and confirms the update of the firmware.

  I deselected the optional software, the devices experience HP and I.R.I.S. OCR, trying to install only the required files two more program scanning HP.

  Thanks for any help solving this.

  I think I understood the question, 10 windows installs its own driver, and the installation program expects the hp driver to install.

  DO this FOR THE HP INSTALLER PROCESS (when the percentage meter goes)

  1. go into the Device Manager and find the printer in the list of devices

  2. right click on the printer and select "Update Driver software"

  3. click on "Browse my computer for driver software".

  4. choose "Let Me pick one...» »

  5. Select the named driver: HP Color LaserJet MFP M477 PCL-6 Pro (make sure it's one with a dash between the pcl and 6!)

  6. click next and back to the installation of hp box and must now see the printer and continue the installation.

  -Alex