HP LaserJet P1102 CE651A does not recognize the new toner cartridge

Similar Questions

• Epson sx438w does not recognize the new ink cartridge

  Epson sx438w does not recognize the new ink cartridge, when change original are

  Contact Epson.  This isn't a problem of Windows or Microsoft.  They should be able to help or offer troubleshooting instructions.

• MX472 does not recognize the new ink cartridges 1401 code

  I recently had to replace my cartridges on my MX472 and immediately after the installation, I got a code on the LCD of the 1401 and several beeps. This code means ink not installed. Therefore, I cleaned the contact strips with alcohol, did a hard reset hold the stop button for 5 seconds, another type of reset hold the button stop for 2 seconds, then press and hold the power button by pressing the key stop 5 times. I also unplugged the printer for 5 minutes with the cartridges from the printer and plugged, reinstall the cartridges and still not received the error code 1401 Check ink back. I went and bought another set of authentic Canon ink thinking that the first set was defective and still a no go on the second set. My printer is ready for the garbage? Its only 6 months!  Someone at - it other thoughts or ideas? Thanks in advance.

  Hi Gregg1,

  Since you continue to receive the error after you perform the troubleshooting steps you mentioned, the printer will require maintenance.  As you bought the printer in the past year, it is still within the warranty period; Please call or write us using one of the methods on the page contact us for further assistance.

• Western Digital WD10EARS internal hard drive Caviar Green 1 TB - my system does not recognize the new drive

  I recently bought a computer Dell 4700 to a friend with Windows XP installed. I've updated the memory to 2 GB and now seeks to install a WD10EARS 1 TB harddrive. The new works of fine memory is not the hard drive. My system does not recognize the new drive. I contacted WD for help and they told me to try diferent rider combinations that were Jumper 1-2 and 5-6, still does not work, I checked the hardware compatibility list and he said he would start uo without modification. This isn't. I would be very greatlyful for any suggestions, to HELP!

  I've had several people tried to help me solve my problem. They were all, I thought, more than I am computer savvy. As time progressed, solutions became more complex. After they all left without resolution I thought and it appeared to me that the simplest solution might be correct. One person had checked. I turned on the computer and when the Dell logo came I pushed the F12 key to open the Dell configuration screen. The drive on which the new drive has been installed has NOT been activated! Duh! I activated the he and the program Acronis recognized and everything went like clockwork after that. Phew! What relief! Thank you for your comments I am just glad that my problem it doesn't require resolution. Are Mod

• Satellite M50-A-110 does not recognize the new SSD?

  Hello

  I bought the M50-A-110 model and tried to replace the HARD drive by a Pro 840 Samsung SSD. The laptop does not recognize the SSD drive, so I sent him to the local Toshiba service for inspection.

  They discovered that the laptop does not recognize ALL of the latest SSD (they tried to Samsun, Intel, Crucial, Kingston and SSD Seagate). They checked, and I possible newer BIOS, so this isn't a problem, and the SSD worked fine on other computers.

  Someone knows how to solve this mess?
  Toshiba has a BIOS beta I could try?
  Any other ideas would be welcome.

  As a user of long date Toshiba, I must say that I am a little disappointed. I mean I work in it, and this is the first time that something like this happened to me with a new product.

  Hello

  I can't believe that Satellite M50 - A can not handle any of the mentioned SSDS.

  I upgraded my Toshiba laptop with SSD Pro 840. But before I did, the update of the firmware of SSD was necessary. Before the firmware update, the SSD has failed, after the firmware update, BIOS can handle the SSD.

  I would recommend to check the SSD for the firmware update!

• Windows Media Player does not recognize the new downloaded songs

  I have a Pavilion a4310f Prod Nr: race AY014AA-ABA, Win 7 Home Premium 64-bit.

  I just found out that Windows Media Player does not recognize the songs, I recently downloaded from Wal-Mart music download Site.  The songs can be seen in the music library in a folder called 'Downloads' and I can open each song and he will play when double-clicked.  The problem is that I can't create a playlist containing the new songs and burn a copy of the reading list, because the songs are not listed in the Media Library Player any hot it is sorted (artist, Album, Genre, etc.).

  Any help/suggestions would be greatly appreciated.

  Mitch

  Problem solved!

  Went to: start == > Control Panel == > troubleshooting == > view all == > and ran troubleshooting on the library and the settings of WMP.

  Convenience store detected library corrupt and "in media files appear in the WMP library.  Then ran convenience store on WMP settings which reset OMP to default settings.  After that, everything worked as announced.

  Thanks to Big_Dave for putting me on the right track.

• Satellite A100 does not recognize the new CD/DVD drive

  I bought a new CD/DVD drive for my A-100 of Toshiba Satellite age of four year old went crazy and wouldn't work.

  Unfortunately, I bought a DVD of Toshiba Portege A100 / reader Combo CD - RW that is not exactly what I had before the jump that it will still work.

  Unfortunately, I'm surprised because it does not recognize the CD/DVD drive at all: /...
  It seems to work, and the light blinks I think that it is not broken.

  I just plugged it because that's the way I was told to do.
  I need to download the drivers to operate?
  It will work on my laptop, or is it a "most recent" CD player that will not work with my laptop?

  I'd appreciate any help. THX

  The BIOS does not recognize this new CURIOUS because the player seems not to be fully compatible.
  I think there bad master/slave/c-salt settings

  As you know these settings can be changed on the external CD/DVD drive for desktop switching jumper. But it is not possible for computers portable CD/DVD players.

  You can solve it only purchase a new compatible disc.

  Usually the ASP in your country could help you buy this disc of these guys here
  However, you can consult the user manual if there are a few details on the compatible sides.
  My user manual provides this information.

• Cannot use my printer Officejet 4635 to the Mexico. Printer does not recognize the new cartridge.

  I moved my printer in Mexico City, HP Officejet 4635. It uses #61 cartridges. I was told that the 61 in the United States is the same as the #122 to the Mexico. However, the printer say it does not recognize the cartridge.

  Can someone give me some advice?

  Hi artist1234,

  Welcome to the HP Forums.

  Why the printer does not is because the unit is not regionalized for this part of the country.

  To get the printer to work, you will need to contact HP Total Care so that a representative from HP can regionalize the printer for you.

  If you call in North America, the number is 1-800-474-6836.  Seeing that you are in Mexico, please click here to access the information page you need.

  Thanks for your time.

  See you soon,.

• C4385 does not recognize the new router

  Just changed internet service providers.  Although I used this vendor before and not had any problems with my printer, I now have a problem.  My C4385 will not recognize the new network.  Hp network connection software that I run has no effect.   It will not detect a network even if my computer shows an excellent connection to the network.

  When I run the wireless network test report it shows "FAIL" next to "Network Name (SSID) Found."  The recommendation is to "check that your HP printer (SSID) name exactly matches your name (SSID) wireless router.

  I am completely baffled by the present.  I've seen other questions that are similar to this, but none that refer to my model exactly.  Any help is appreciated.

  Please, try the following:

  1. disconnect the USB cable from your printer

  2. make sure to delete any previous copies of your HP printer from the printers (in Control Panel) screen

  3. restart your PC

  4. under the printers screen, enter the following print server properties screen:

  XP: File > print server properties

  Vista: right click on the area of the screen information, and then select run as administrator > print server properties (law as Administrator option will not allway appear)

  Win7: Select any other printer in a left click and you will see the properties of the print server to the Menu bar top

  On the Ports tab, be sure to remove any existing TCP/IP port.

  5. remove temporarily disable your firewall software

  6. start the installation and select reconfigure the network connection / add a device.

• OfficeJet Pro 8100 does not recognize the new router

  I saw this question for other printers, so I hope that there is a response to mine.  I just upgraded the speed of my internet service which involved a new router.  We made sure all the computers in the House worked with her, but I forgot to try the printer before the technician left.  Now my computer thinks printer Officejet Pro 8100 is offline (turned off) and the blue light on the printer blinks.  How can I get the printer to recognize the new router?  I guess I have to add that I do not know where to find the code of the intellectual property that is asked for when I go to the start menu, the HP folder, select my printer, etc.  He said: push the button on my printer wireless, so I push button blue flashing light but that does not produce a number.  Help appreciated!    It's an ATT router and I have the WiFi network name and wireless password.

  Replacement of your wireless router try here.

  http://www.HP.com/global/au/en/wireless/reconfiguring-system-Help3.html

• LaserJet 4650 does not recognize the NEW fusion of image kit

  After replacing the old kit, the menu of the printer (LaserJet 4650dn) does not disply "New fusion Kit", as it must according to the manual, but still asks me to replace the kit (1700 pages of 'go'). What can I do?

  It does not display this message. Must go to configure the device and then scroll up to reset or reset supplies and one of the options is the new fusion kit. Choose and press select and it will reset. Simply launch a menu card in the information menu to find the exact location.

• Satellite A200-1TS - Win XP does not recognize the new HARD drive

  Dear Forum,

  My HD crashed, I installed a new, but XP will not recognize.
  I created a new partition with Partition wizard home edition, and with a Mini XP bootable CD I can access Hd, reading and writing, but if I try to install XP from the CD of origin of the system does not have a usable hard drive.
  Any part of the material blocking this new HD? How can I install windows XP on a hard disk new?

  Thanks in advance for your help

  Can you please tell us what model of laptop do you have?
  Maybe you need to load the SATA driver?

• Tecra 8000 does not recognize the new HARD drive

  I read on this forum and Google search, but nothing helped.

  I think the disk on Tecra 8000 (Pentium II, 266 Mhz) is "dead".
  I tried to replace it with another laptop to see if that would work.

  The laptop does not, even if I put just like the original.
  Y at - it somehow special or what I have to change something in the Bios?

  Hello

  Don t need to change BIOS settings

  As long as you use the compatible HARD disk, the BIOS should recognize the HARD drive automatically without big problems
  What drive did you use? What size, interface, etc.

  The Tecra 8000 is an oldie and I think that you could use only the 4 GB; 6 GB; 9 GB; 10 GB; 14GB IDE hard drives.

  More large hard disks would be not recognized by the BIOS.

• Satellite L305D-S5881 does not recognize the new HARD drive

  Ok. I've had this laptop for a while now.
  It crashed recently. So, I tried to start it up.
  I got "Winload.exe missing or damaged".

  Fortunately, I found an answer to this!
  I got the Vista installation disc and inserted.
  I had this "PAGE_ERROR_IN_NONPAGED_AREA". I fixed too. Stick of 1 GB of RAM to my computer was bad.

  So I replaced it. And during the installation, it hangs. And beeps and undesirable.
  So I thought it was my hard drive. I have a new. (http://www.toshibadirect.com/td/b2c/adet.to?poid=431567 please TAKE a LOOK BEFORE RESPONDING).

  I (try) to install and it does nothing.
  I turn it on and it goes to this page with as my enthernet info. Then I go into the BIOS and it appears. I think I could install it wrong.

  Any help?

  Hello

  I think that the new HARD drive is not recognized, because you have not installed the SATA drivers!
  The new mobile phones support the new SATA controller and especially the drivers are not included in the Windows operating system.

  So, you must first include the SATA drivers before install you the operating system.
  AFAIK the L305D supports an AMD and ATI chipset and SATA drivers must be placed in the ATI graphics driver package.

  On the other hand, you could install the operating system without the use of SATA drivers.
  I think that the BIOS must contain the SATA mode option. Usually it s set to AHCI. Pass this option in compatibility mode and you should be able to install the operating system.

  Cheers mate

• Windows 7 does not recognize the new WD external hard drive added to the usb port

  Recently, I tried to add my third USB WD hard drive to my computer.  It's a My Book Essential.  The meter turns and the virtual cd drive is listed in WD, but the hard drive itself does not appear on the list of devices with a drive letter.  My my first two books are readers: J:, and L: I have no "new device found" message   I search for new devices and it the PC do not find anything.  If I click on the virtual CD drive (M :) it askes if I want the computer to allow WD to make changes...) I say Yes and the screen flashes and nothing happens.
  The drive be defective?  Any other ideas?

  Hello

  Have you tried to connect the external hard drive on another USB port?

  Try to connect the WD external hard drive on another computer.

  Follow these steps:

  Method 1: You can run the troubleshooter in the following article and see if this fits the Bill.

  Open the hardware and devices Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Also, run the Fixit.
  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Method 2: Check if the external hard drive is recognized in disk management and assign a drive letter to the same.

  To open disk management, follow these steps:

  a. click Start, type disk management in the start search box and press enter.

  (b) if the drive is detected in disk management, I suggest you to assign a drive letter and see if that does the trick.

  For instructions, see this article change, add, or remove a drive letter