HP pc hardware diagnostics uefi

Similar Questions

• Sprout of HP: HP PC Hardware Diagnostics UEFI install faulty

  5 times the HP Support Assistant attempted to update the "HP PC Hardware Diagnostics UEFI". Whenever he fails. After each attempt, I made a stop and then tried again.

  After two attempts to install from HP software web page I got it to install correctly. Then I got the HP Support Assistant to do another scan and all is good.

• Pavillion dv6 notebook PC: P PC Hardware Diagnostics UEFI - test failure

  HP PC Hardware Diagnostics UEFI - Wide system Test

  Failure ID: 6FH3UT-5AF85H-XD002K-60W103
  
  Product ID: LG266PA #ABG

  The hard drive gave error failure - ATA, model type is serial ST9500325AS [personal information]

  WHAT should happen?

  Also battery check: primary - calibration required (21) - How to calibrate?

  And I don't understand why they provide HP PC Hardware Diagnostics UEFI - if their information so that it does not exist.

  The hard drive has failed and needs to be replaced. If you are still in warranty HP will send a replacement. If this is not the case, a laptop SATA hard detail can be used. Just be sure to get one of at least equal quality of the original in order to use recovery media to install the drivers/software/Windows on the new hard drive. It may be big, but not small ability more. For example if you have a 500 GB hard drive you can use a 750 GB hard drive, but not a 320 GB hard drive.

  Calibration of the battery:

  http://support.HP.com/us-en/product/HP-Pavilion-DV6-3200-entertainment-notebook-PC-series/4308480/model/5051632/document/c00821536#AbT3

• Uninstalling hp pc hardware diagnostics uefi

  Hi, I have HP pavilion n010ek, I installed the pc hardware diagnostics uefi since section hp drivers in this site, everything worked, and a score is made as in the picture (HP_TOOLS f), unless I want to uninstall it but I couldn't find in the Control Panel, how can I uninstall the hp pc hardware diagnostics uefi?

  Hello

  You can delete the HP_TOOLS partition as follows.

  Hold down the Windows key and press R.  Type diskmgmt.msc and press ENTER.

  In the lower pane (chart) showing the partitions, right-click the HP_TOOLS partition and select delete the Volume.

  Once completed, this leaves an entry for "unallocated space".

  You can then right-click on the C partition and select Extend Volume to add to the C partition unallocated space.

  Kind regards

  DP - K

• HP Pavilion 030ea-b: Hardware Diagnostics failure error

  Hello

  I ran HP PC Hardware Diagnostics UEFI. Details [disk 1]:

  Smart Check: spent

  Long DST: failure

  Failure ID: 0LG55D-000837-X87T1A - 618P 03

  Please could someone tell me what is failure and how do I correct?

  Thank you very much

  Hi @23 - B030ea,.
  
  Welcome to the Forums of HP Support!  I understand that tests your cam drive upward with an error when you run the UEFI. I'm happy to give you a helping hand with this.

  I checked the ID failed you posted and it gave me the error code SMART Drive from 305. Now if your hard drive still works for you, I highly recommend to make a backup of all the data that is important to you as soon as possible. A SMART test drive is usually a predictor of drive failure. It could happen today or in a few months, but rather than to risk of losing everything, it is best to take precautions.

  See also this paper: HP laptops - Hard Drive failure errors: failure Imminent, Smart, BIOHD, HD535, etc.

  Once your data is safely backed up, you should probably look at a replacement hard drive.

  Please let me know if it works for you and if it does not solve your problem, please mark this message as a solution. Bravo would be appreciated as well.

• Partition HP_TOOLS after update from HP System Diagnostics (UEFI)?

  Hello

  I bought a Compaq HP 6730 s about 2 and one and a half years. Last time I installed Windows was in 2009, when I switched to Win7 Pro x 64. I usually keep my system up to date so I decided to use HP Softpaq Download Manager to see what is new because I have not done in a year about. By updating HP System Diagnostics (UEFI) I noticed the installer to begin creating a new partition using DISKPART. It has 2 GB of E:\ and created a new partition HP_TOOLS (H:\).  First of all, was it really necessary given that I had only 3.5 GB of free space on E:\? In addition, the old version of HP System Diagnostics (UEFI) has not used a separate partition. Secondly: is it really necessary to keep or is the only partition something temporary created to facilitate the update process (although this makes no sense to me), meanning can I simply delete and merge into E:\.

  Third: in the case where HP_TOOLS is not delete recomanded, at least hide by using the local Group Policy Editor?

  Thank you!

  The latest version of the installer of HP System Diagnostics (UEFI) gives an option for installation on drive hard or on a USB flash drive according to your needs. I personally recommend not not to delete the partition HP_TOOLS as its useful during the process of updating the BIOS in case if you want to do a restore etc.

  HP_TOOLS partition is also useful in F2 (the System Diagnostics) market in the case of any emergency if necessary.

• Pavilion g6 2226tu: 'no hard drive installed' error in material diagnostics UEFI

  My pc is very slow and freezing much n after troubleshooting and consulted technicians on the chat, I went to the recovery. It's everything is OK with recovery but the same problem was there. N all of a sudden today I tried to restart it when it froze, it showed a blue screen with the error 'blackout driver State' it displays information is collected to be sent as a report. After 10 minutes, it ended at 100%. N he tried to restart, but he went to gray white screen after the execution of the repair automatic FIR seconds. After five minutes of waiting, I turned it off n tried to turn on n check with hardware diagnostic uefi. But he could not detect my hard drive of 500g. She appeared no hard drive or hard drive not installed message.
  Now what is it? My hard drive broke down, or it could be another hardware problem?

  He succumbed to a slow death for a long time, but now he is dead and must be replaced. Chances are that it is past the time what data could have been recovered. Sorry for your loss. If you want help replacement and software, we can do.

• Report of hardware diagnostics that enabled a single core in core 2 machine

  HP P6370t desktop

  Windows 7 64 bit

  Processor Intel core I3 530 CPU @2.93 Ghz

  performance of HP 6.0.5297.34 diagnostic tools

  The system ran diagnostics of material for a "monthly" race

  He noted "there are 2 hearts in the processor and only 1 core is enabled.

  Several questions (at least):

  Are there conditions reported error of 'false' with HP hardware diagnostics on this issue?

  How would I go about correcting this problem?

  Thank you

  Welcome to the jimbauerv forums,

  I did some research for you, and I came across a thread the guy had exactly the same problem, but he had 4 cores (3 of which somereason were not active).

  He showed that by removing the CMOS battery and put back in after 2-5 minutes. And the computer showed he had all 4 Active cores...

  Another user who has sent by clicking Start--> Run--> type MSCONFIG--> Boot--> Advanced Options

  If it is checked, uncheck 'Number of processors'. If not check it out and in the drop down list select 4 (according to the number of cores you have) and you're done.

  I hope this helps

• Remove HP System Diagnostics UEFI

  I installed HP System Diagnostics UEFI (SP52407) on my Elitebook 8530p running Windows 7 Enterprise 64-bit.

  I want to uninstall this program if possible it's my failure of System Image backups.

  The new partion created by this program is FAT 32 and Windows 7 will not save, NTFS only.

  When I click on create new system image, it is said that the following drives will be saved:

  (C (System))

  HP_tools (F (System) with no option to remove this.)  And if I chose my own thing same backup.

  While I can uninstall it somehow? (does not appear in the programs) or should I delete just the partion?  Not sure if this will help to either.

  Hello pjamme,

  Your EliteBook is a business model.  Your question would better answer on the HP Enterprise Business Community Forum

  Good luck!

• Boots only to the Startup Repair. Hardware diagnostics found bad blocks on the hard disk. is it possible to move data outside of Windows?

  Original title: Hi, I have a Dell Inspiron 1545 laptop.  Recently, he stopped working and would go only to the screen that asks if you want to run the Startup Repair tool.

  Of course whenever I launch it, it goes back to this screen.  Check the diagnostics through the F12 boot, I had three error codes: 0F00:1344, 0244 and 1 A 44.  These were all on the same three blocks.  The message was impossible to read, replace the drive.  I'm really the most responsible for recover my photos, documents, etc. and have an external hard drive.  Is it possible to do so, even if Windows (Vista in this case) will not start?

  Hello

  You can try these methods

  Data recovery

  1. remove the hard drive and it slave in another computer

  2 buy or borrow a USB disk drive hard put in yout case then plug it into another computer and read the hard drive like this

  3. try Knoppix

  http://www.Knopper.NET/Knoppix/index-en.html

  BUT this method depends on your hardware in the computer that failed

  If this does not work, you may need to contact the data recovery specialists

• Hardware diagnostics: "SMART short Self Test - failed" and "targeted read Test Failed.

  Original title: "SMART short Self Test - failed" and "targeted read Test Failed", all the patches?

  When using PC checkup of Dell I get the following errors; during the analysis of the material. "SMART short self-test - failed" and "targeted read Test Failed", all the patches?

  Hello Duane,

  Teke section of the Web site that speaks of similar problem.

  http://forums.techguy.org/hardware/906455-smart-short-self-test-fail.html

  The problem is with the hardware and you can get in touch with Dell computers.

• Hardware diagnostics

  Hello all :)

  I am trying to run hardware test on DELL switch n2048 of CLI and the WEB, but I can't find that option.
  Search in google without result. Have the latest firmware. Have a problem with this switch, but can't understand what the configuration or hardware

  Please help me.
  I thank you very much.

  There is not an official diagnostic equipment that you can download and run on the switch. Here are some options that you can use to help monitor the switch.

  -console # display system, this will show you the current state of the temperatures, power supplies and fans. This can be used to help search for some defective components. This can also be seen in the graphical interface under system > General > health.

  -console # see logging, any time, an error occurs, including hardware errors, a log message is stored. This can also be seen in the graphical interface under system > Logs.

  If logging is corrupted or has aged, then it will not show you the papers you need. And if everything is back to normal, then the show system command can be useful right now. To contribute to monitoring the switches, it may be useful to set up a syslog server. Page 369 of the user guide contains information about setting up a syslog server.

  http://Dell.to/1WFiTWT

• Pavilion 17-f010us: Hardware Diagnostics

  I have a Pavilion 17-f010us running Windows 10. I want to run a diagnostic equipment on it, but can't seem to figure out how. On older models running Windows 7 and below, I used to be asked to press a specail over powering (ESC or F10, etc.) who could take me to a boot menu where I could enter the BIOS or run a diag utility. Can someone tell me how I would do it on this one? Thank you in advance.

  Hello

  Stop of the laptop.

  Tap away at the esc you key start Notepad to open the Start Menu.  From there you should be able to select the Menu of diagnosis ( f2 ).

  Kind regards

  DP - K

• After the automatic running Hardware Diagnostics, I lost my sound. That happened 3 years ago, but can not remember what to activate the sound.

  After an automatic run "Material of Tests of diagnosis" and at the output of the program, I lost the sound on the computer. This happened to me 3 years ago when I had just bought computer and I took it to the Greek Squad. It was just something that was muted and I don't remember how to get to the appropriate window to correct.

  I fixed it myself and I don't know how. Thank you for allowing me to post here. Best wishes.

• HP System Diagnostics UEFI?

  After I reformat my laptop, I installed this driver. It creates its own partition from HARD drive main (shrinks by hand and gets 2 GB). but after the reduction of the main HARD drive, there will be a 8 MB unallocated. is there a possible way that the memory will be used or return the 8 MB on the main HARD drive? tried creating another partition but it always ask get hand.
  -This driver is required? What is doing?

  just find a way to merge. http://discussions.VirtualDR.com/showthread.php?t=203145

  SOLVED!