HP psc 1410 could not set up the wireless network

Similar Questions

• Windows could not connect to the wireless network

  Hi all, I just bought a HP dv4 series. I receive this connection problem. My laptop can detect the network but still fail to connect. I need to press 'connect' to get connected. It sometimes takes 40 + tries to connect to the network.

  I am using D-Link 2640 - T and it's the WEP security.

  Network card: broadcom 43225 802.11b/g/n

  Can anyone help? I tried to delete the profile for the wireless network and connect to the rear, it did not work. I even reset my wireless router.

  I guess I found the solution, at least it works fine for me for a few days

  1. right click on my computer

  2. click on properties

  3. Select Device Manager

  4. Select yout network cards

  5 right-click the map network and choose 'properties '.

  6. go to the Advanced tab

  7. in the title, choose "rate (802. (11 b / g) ".
  8. choose '54' in the drop-down list instead of the default "best rate".

  Hope this helps others who face the same problem like me

• Problem creating ad hoc network-error: Windows could not set up the network.

  Original title: problem creating ad hoc network

  Hello dear,

  When I tried to set up an adhoc network and after entering the name and password of the network. Following up error message pop (Windows could not set up the network).

  I use windows 7.

  P.S. before I used to create the ad hoc network with no problems. But now no more.

  Kind regards

  Ana Paula Yousef

  Hello

   
  Did you change in the computer before this problem?
   
  I suggest to go through these steps and check.
   
  Method 1:
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows
   
  Method 2:
  Error message when you try to connect to an ad-hoc connection in Windows Vista or Windows 7: "Windows cannot connect to " http://support.microsoft.com/kb/946481 ".
   
  You can also check:
   
  Set up a computer-to-computer (ad hoc) network.

  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-computer-to-computer-ad-hoc-network

  Ad-hoc networking.

  http://Windows.Microsoft.com/en-us/Windows-Vista/ad-hoc-networking-how-the-network-with-the-funny-name-can-make-your-life-easier

• I've updated windows and now my computer does not connect to the wireless network.

  I've updated windows security updates and now my computer does not connect to the wireless network.  Until then, it worked very well and even now it will connect through wired connection but not wireless.

  Hello
   
  You can follow below link that can help you to solve your problem:
  How to troubleshoot wireless network connections in Windows XP Service Pack 2
  http://support.Microsoft.com/kb/870702

• My computer does not connect to the wireless network

  My computer does not connect to a wireless network. It's almost like there is no WiFi. I go into the settings and nothing is. I know that the networks are there because the other computers connect to it. He says always "no connection available. When I try to pull of boredom he tells me to plug an Ethernet cable, which is the thing that I try to avoid. I want to connect to WiFi.

  Based on this information, your laptop isn't wifi, it is turned off, or it is broken.  A wifi used to work?  If so, what happened to your system, just as the problem started?

  Type "Device Manager" in the search box and press ENTER.

  • Look in the Device Manager to the network adapter section.
  • What devices are listed?
  • Are there warning icons?
  • It appears to be a wireless adapter, what's his name? Double-click it and to report to what is shown for "State of the device.

  You can also provide additional diagnostic information:

  • Type 'Information system' in the search box and press ENTER.
  • Click in the system information window and select all (CTRL + A) and copy (CTRL + C)
  • Paste (CTRL + V) the data in your response here
  • Return to system information window and click on the + next to "Components", then click on the + next to "Network", then click on 'map '.
  • Select all (CTRL + A) and then copy (CTRL + C)
  • Paste (CTRL + V) the data in your answer below, other data Information System

• C7180 not found on the wireless network

  We have a Photosmart C7180 was working wonderfully for a few years.  Wireless connectivity is great, even move to a new city/home/internet provider required only run the printer Wireless Setup Wizard, and "poof" things began to print.  So far.

  We got new internet service (new router) and now the printer is not found.  No amount of tweaking seems to be able to get our Mac to see.  We have:

  • Redownloaded and restart the installation of the driver on the Mac.  Connect via USB, it works very well.
  • Rerun Setup wireless network on the printer.  He sees the wireless network and complete Setup.
  • Checked the IP addresses: everything is comfortably accessible 192.168.0.xxx.  The printer, the computer, the router, everything in this range.
  • Connected to the printer in the Mac browser to http://192.168.0.6.  He can be seen and worked with.

  However, when we try to print or run the Mac installer, the printer is not found.

  Help?

  Success! With the help of an old wifi access point on the router and it all works. Same Bluetooth? Thank you!

• BlackBerry smartphones not connected to the wireless network

  Hello
  I went to a BB tour and I'm trying to recover My World. Whenever I try to update my list, I get an error that says: 'we cannot retrieve your list. Please make sure that your device is on the wireless network.
  I can reinstall many of my applications, but there are themes that I bought that I now can't come back.
  No idea why I can't get my list?
  Thank you!

  Hey sorry,
  World of the BB app reloaded itself after a can of weeks but thank you

• Just bought a HP 6500 e has and a computer (windows 7) could not connect to the wireless printer

  My new printer is not recognized by the network wireless in my computer (Windows 7). USB print ok

  The printer seems to be connected to the network, but my computer is not connected to the printer. It will not print on request. The print project going on in Quebec but will not communicate with the printer wirelessly. If I plug in the USB it will print.

• HP 7520: HP 7520 will not connect to the wireless network

  There is some additional information to

  http://forums.Xfinity.com/T5/home-networking-router-WiFi/HP-7520-will-not-connect-to-wireless-networ...

  on this issue.

  Have several APs for a single wireless network allows the printer foolish law.  (Not a Repeater, a second AP connected to the local network with the same configuration of network for security, etc.).

  I solved this problem.  In accordance with the discussion on the link, the problem is that the printer cannot connect to a wireless network if there is greater than 1 for a wireless network (SSID) name wireless access point.

  This thread has had several useful suggestions, but what finally solved the problem, it's the second point has access to a mode where I can create a 'virtual' access point and, above all, a SSID associated.

  Note that not all access points or routers support virtual APs, but this function seems to be more common over time.  Older models is not able to do that.  However, a new access point is sometimes cheaper than a new printer.

  If you do not understand the jargon in the procedure below, I recommend that you find someone who does, then they can do it for you.

  Solution:

  1. On one of the wireless access on the network, create an a new virtual AP with a slightly different name SSID (for example < name of the network - > _1), on the same VLAN (usually VLAN 1).  You may need to put the AP in "multiple AP mode" or something similar, and then restart the AP.  All other settings (DHCP, security, mixed mode b/g/n, etc.) must be the same for the new SSID.
  2. Run the printer Wireless Setup and connect it to this new SSID
  3. Confirm that the printer can be seen by other devices on the network

  Tips:

  • Check the security is the same as the original SSID, Alternatively you can create a vector of insecurity in your network.  Do not WEP-128 when the other SSID uses WPA2 AES, for example.
  • The AP I had had several resets to make it work because of the mode and parameter changes.
  • If you connect the SSID but cannot connect to or be seen by anything on your network, check the new SSID/AP is in the same VLAN as the original.
  • Because the printer is not roaming, and the speed is not a problem for me, I used the access point that could support this solution, which is deeper and slower than my primary AP.  I have not noticed any problems.

  The printer has been reliable on the wireless now on the new SSID, 48 hours.

  I have not upgraded any software on a client of the printer (PC, Mac, phones).

  I think that it is a positive confirmation that the problem is with the implementation of the printer of the stack of network and not with the driver or client software on remote devices.  The 802.11 protocols provide for a network name (SSID) wireless with several access points using different MAC addresses.  I suggest this HP look into this as a potential bug with their network printer for the 7520 protocols stack.

• Photosmart 5524: Photosmart 5524 will not connect to the wireless network

  I recently moved house, and since the move does not connect the printer to the network.

  The router and the parameters are the same as before the move, and appliances are on opposite sides of the same coin.

  Initially, he sees the network, but does not connect when you press the WPS button or the password.

  After the first attempt he cannot see all networks at all until the settings are reset, even if the network name is entered manually.

  Printed on the test result to get a 'Pass' for YOU wireless and WIRE WORKS, a "failed" to FIND NAME of NETWORK and "Not run" on all other tests. The proposed solution is not useful, as it suggests using the Wireless Setup Wizard to set up the printer, which I already do.

  No other device has problems see the network or connection to it. MAC filtering is not lit. Some devices have a static IP (required to stop Ipad wife being a tyrant of intellectual property), but the router DHCP is still active for most devices.

  Temporarily remove your SSID of your router password. Now try to connect to your SSID unsecured. Are you successful? If so, go back and add WA2 - AES with a password and try again.

• Map Wi - Fi on Satellite L40 does not connect to the wireless network

  Hello

  I have Satellite L40-15B with a realtek RTL8187Bcard. Problem is I Don t get a connection on wifi, but everything seems ok. I ve installed the BIOS update, the latest drivers and updates for Vista. Psychic Network is turned on, network switch is on, and yesterday everything worked fine. I had this problem too when I bought the laptop but thought that I solved it. Not!

  Vista tells me that everything is installed and works well. I can also see some available networks, but when I try to connect it just doesn't work.

  Someone at - it an idea what to do next? (by the way the network is ok other laptop computer wifi works fine)

  Thank you

  Albert

  Hello

  Your wireless network card seems to be properly recognized in Device Manager. And the problem is that you are not able to connect to the WLan router. Am I wrong?

  Have you tried to disable the Wlan encryption settings and then test the WiFi connection?
  You should also try to reset the settings of the Wlan router.
  Sometimes it helps.

  I got a WLan connection problem too I've checked everything twice and nothing worked Finally I reset the Wlan router. and surprise, surprise it's a key

• CQ60-210US reformatted for Windows XP Prof, but it does not connect to the wireless network...

  Long story short, I tried recently to "downgrade" my husband computer CQ60-210US laptop from Vista to XP.  I followed the very detailed guide posted here and everything seems to work great but my computer does NOT connect to my home network.  It comes as an available network, but when I try to connect it goes on to say that the network is no longer available - is yet to ask security key.  I tried to click on the connection to a neighbor to see what would happen and it seems to go further (it asks me the security key).  I can connect directly using the ethernet to the modem cable.

  This laptop was initially working on my network wirelessly with Vista.  I use a CLEAR 4 G wireless modem.  The signal from the modem is good.

  Can anyone help me identify the problem and propose a solution?  Everything else seems to work well.

  Thank you very much!

  Try to uninstall the Atheros driver, you have now and install another:

  FTP://ftp.HP.com/pub/SoftPaq/sp52001-52500/sp52131.exe

• OfficeJet 4620 3-in-1 printer will not print on the wireless network

  Have updated my Mac OSX to Yosemite (10.10), & now the 4620 Officejet will not see my WiFi network.  Have already uninstalled & reinstalled, used USB and installation CD.  Restarted the router also.  The printer went as far "Retore System Defaults".  Any suggestions?

  THX

  Hi @tomiet,

  Welcome to the HP Forums!

  I see that your HP Officejet 4620 will print on your wireless network, using Mac OS X 10.10. I'm sorry to hear that, but I'm happy to help you!

  I recommend trying an installation installation of Wireless USB. Please consult this guide, convert a wireless USB connected printer. In addition, this video can help as well, Configuration of wireless USB printers.

  I hope this will solve your problem of connection and have a nice day!

• Name of network problems; numbers and not showing in the wireless network ID

  In my network and sharing on the map at the top of the page Center, my wireless network is identified as Queensgate 2 on my Pavilion Entertainment PC (Vista). On my g7 series Pavilion, it is identified as Queensgate 3 (Windows 7). In the zone just below the map on two machines, the network is identified as Queensgate. Queensgate is the correct ID. There are no numbers on my SSID wireless router.

  When I connect to the network dialog box confirms the connection to Queensgate (no numbers).

  Can someone tell me how to solve this problem?

  Thank you

  Frank

  Hi Frank,.

  I think I misunderstood what you rename, but seeing your description of what you have changed in Vista, I think I know what you need to do in Windows 7.

  Open the network and sharing Center.  Look at the icon in the middle of the network map - you should see the icon itself below the network card and to the left.  Click on this icon and you should be able to change the name of the network.  Click Ok after you change it and you should see the change immediately reflected in the network map.

  Kind regards

  DP - K

• Could not set created the default dashboard dashboard

  Hello
  
  I am not able set created dashboard dashboard by default from my account - > Preferences - > start page.
  
  I placed my dashboard under a folder created in shared folders. (Otherwise, I am not able to find it in the start page drop down).
  
  After selecting my startup page drop-down dashboard and clicking ok, his throw what follows: -.
  
  Exception occurred when saving the preferences of the user to catalog access denied for the user/users/weblogic/_prefs/userprefsxmlstore path.
  
  I have read several articles on, "defining the default dashboard with the variables of the RPD and initialization blocks...". But it should be done, just analytical... .right?
  
  
  Thanks in advance

  Hi Ludovic,.

  It is a known problem, delete the weblogic users folder and restart services as explained here,

  http://www.bravesoft.com/blog/?p=722

  Make a backup of webcat before making the change.

  Kind regards
  DpKa