Hp15: I see an error msg when I try to start by saying that (the smart drive as fail (301)

Similar Questions

• 500 PSC GETS STUCK ON WARMING UP WHEN I TRY TO COPY ME SAYS THAT THE SCANNER DOES NOT

  My HP 500 CPS still print fine but when I try to scan something it fails. I turn on my computer and printer off a few times and it will scan. I thought it was a driver issue first of all them perhaps the cable. It has been getting worse and now it copies. I disconnect from the computer and try to copy it gets stuck on the warm up and then gives me the same error SCANNER FAILURE TURN OFF THEN ON. The light is on and it loads paper acts as a heat sensor is bad. I have a good rear electronic on the ground. Maybe someone could point me in the right direction. I really like this old printer and I am ready to spend time fixing it.

  Thank you

  Want to thank those who took the time to read my problem. I FIXED IT. On a forum someone talked about the problem of warming up and I realized that the only thing that needs time to prepare would be the light of the scanner. I disassembled the scanner Assembly cleaned the mirrors and that fixed it! Has been and still is a good SPC. In order to reduce the cost, I filled my cartridges.

  I gave myself another problem. I uninstalled the drivers several times trying to solve the problem of the printer. Now I have additional drivers in device for printers 1284,4 Add-in Manager. No matter what I do XP reinstalls them. A few years I had back get a program installed at HP to clean the registry file so that I could do a clean install of my HP PSC 500 windows drivers. Now I can't find it. guess I didn't save TI - DAM! Been looking on the web site of HP have yet found. - PROGRAMME of INSTALLATION of ANY BODY GOT A LINK FOR HP.

  THANKS AGAIN

  Steven Ruther

  PS; They have me as a student. I have 60 years and owned by a company of software from 1980 to 2000.

• I got a serial number, but when I try to license it says that the number is not valid

  now what should I do?

  Hello

  Please see: -.

  Error "serial number is not valid for this product". Creative Suite
  http://helpx.Adobe.com/Creative-Suite/KB/error-serial-number-valid-product.html

  Error failed to validate the serial number | CS6
  http://helpx.Adobe.com/Creative-Suite/KB/unable-validate-serial-number-CCM.html

  Hope this helps!

• Hello, I was wondering why my adobe first pro ((when I try to open it)) say that "the application could not start correctly 0xc000007b" I need help as soon as POSSIBLE. Im trying to work on a film, but I can't until I have correct this problem. Help?

  Hello. I need help as soon as POSSIBLE, when click on my first adobe, it says "the application is unable to start correctly 0xc000007b" I need major help as soon as POSSIBLE - does anyone know how to solve this?

  ... 07 b problems http://forums.adobe.com/thread/1355374?tstart=0

• "Error 1079: the account specified for the service is different from the specifiedfor account other services running in the same process" when I try to start it manually to the top of some program services.

  Original title: How can I restore my services to the default state.

  Here is the error message when I try to start it manually to the top of some service programs.

  "Windows cannot start the Diagnostic Policy on Local computer service."

  "Error 1079: the account specified for the service is different from the specified account.

  for other services running in the same process. »

  Hi raospent,

  1. have you made any hardware changes or software on the computer before this problem?

  2. what services you try to start?

  You can follow this link & check if it helps.

  Services do not start, and you receive an error 1079 on a computer that is running Windows Server 2008, Windows Vista, Windows 2008 R2 or Windows 7

  Hope the helps of information.
  Please post back and we do know.

• I get 656 error Code when I try to download my updates to the windows desktop.

  I get 656 error Code when I try to download my updates to the windows desktop.

  Do you mean * 646 *?

  See:

  http://support.Microsoft.com/kb/2258121

  Very popular.

  TaurArian [MVP] 2005-2011. The information has been provided * being * with no guarantee or warranty.

• Converter does not have "an error occurred when opening a virtual disk. Verify that the Converter server and source running machines have network access to the ESX/ESXi hosts source and destination. »

  Hi all

  I'm having some trouble converting server physical windows using autonomous vConverter 5.5.

  error message:

  "An error occurred when opening a virtual disk. Verify that the Converter server and source running machines have network access to the ESX/ESXi hosts source and destination. "

  I have attached the bundle newspapers. Please notify.

  See you soon...

  Your error is:

  2014-11 - 04T 18: 27:27.587 - 08:00 [01236 info "Default"] GetManagedDiskName: Get disklib file name as vpxa-nfcssl: / / [a0110-vmgt70-001] WIN-MOVRCVCSITG/WIN-MOVRCVCSITG.vmdk@a0110tesxhyp01.datacenter.telenorservices.com: 902! 2 b 52 87 75 03 03 ff 49-67 2f 3 a 61 76 and 00 cd e1

  2014-11 - 04T 18: 27:27.587 - 08:00 [01236 WARNING 'Default'] [, 0] NfcNewAuthdConnectionEx [NFC ERROR]: unable to connect to peer. Error: Failed to search for host for a0110tesxhyp01.datacenter.telenorservices.com server address: the requested name is valid, but no data of the requested type was found

  2014-11 - 04T 18: 27:27.587 - 08:00 [01236 info "Default"] Sysimgbase_DiskLib_OpenWithPassPhrase failed with 'NBD_ERR_NETWORK_CONNECT' (error code: 2338)

  Check the manual on the required ports.

  HTH

• I get Themida error message when I try to start copytrans

  I get the Themida error message when I try to start copytrans, what can I do?

  Hi P1961,.

  Try to install the clean boot and check if it helps.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: Don't forget to return the computer to normal after completing the troubleshooting by following the steps described in step 7.

  Hope this information helps.

• Error 1068 when you try to start the WIA service after the installation of the W7 SP1

  Original title; Error 1068 when you try to start the WIA service after the installation of the W7 SP1. The scaner to my Epson Workforce 633 all-in-One printer does not work after that.

  SCANeR to my Epson Workforce 633 all-in-One printer does not work after the installation of the W7 SP1. I contacted Epson support and they told me I had to contact MS support to get help this isue. The problem is that something is not letting the WIA service to start and I am getting error 1068 when you try to start the WIA service.

  Hello

  Method 1: Try to uninstall and reinstall Epson drivers and related software.

  Visit our articles to do the same below:
  http://Windows.Microsoft.com/en-us/Windows7/uninstall-or-change-a-program
  http://Windows.Microsoft.com/en-us/Windows7/install-a-program

  Method 2: Also scan SFC (System File Checker) on the computer.
   http://support.Microsoft.com/kb/929833

  Hope this information helps.

• Windows Media-Play list. When I try and play it says that it cannot find the usage rights

  I recently had my computer repair, my music files are still on the computer but when I try and play it says that it can't find usage rights. How can I find these and restore them.

  original title: list of Media-Play of Windows.

  Hello

  Method 01:

  I suggest you follow the link and check.

  http://support.Microsoft.com/mats/windows_media_player_diagnostic

  Method 2:

  Try the remedy proposed below and let us know if it works for you.

  (a) click on the Start menu, choose all programs, then Accessories, and then right-click on the element of the command prompt and select run as administrator

  (b) click on continue to allow it to open a prompt with administrator privileges

  (c) run this command at the cmd prompt: sfc/scannow

  (d) the cmd prompt should list text stating "start system analysis. This process will take time. »

  (e) wait for the scan to complete (this may take several minutes, so be patient).  This command will scan all protected system files and attempt to replace the incorrect versions by appropriate Microsoft versions

  (f) when the analysis is complete, the SFC tool will indicate whether or not it found no problems and whether or not he was able to correct

  (g) if any errors are reported that SFC could not resolve, there are steps in this knowledge base article which explain how to locate and attempt to correct errors

  (h) after the correction of the errors that are found, try to use Windows Vista Media Player again.

  I suggest you to follow the links and check out them.

  Solve problems in Windows Media Player

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-in-Windows-Media-Player

  The Player Windows Media DRM: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/Windows-Media-Player-DRM-frequently-asked-questions

• ox800704ec error code when I try to start my computer

  When I try to start my computer to receive an error code that says: "Windows has encountered a critical problem and will restart automatically in one. Please save your work now. "This happens whenever I try to start. Can you help me with this?  Paul @ (deleted number).

  Hello Paul,

  1. what version of Windows is installed on the computer?

  2 have had any changes made to the computer before the show?

  3. what security software is installed on the computer?

  Try these steps and see if it helps.

  Note: The links below are applicable to the Windows Vista operating system and Windows 7.

  Method 1:

  Step 1: Safe Mode

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  If the computer works fine in safe mode, and then follow step 2 and check.

  Step 2: Clean boot

  To help resolve the error message, you can start Windows Vista or Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Please note: After troubleshooting, be sure to start your computer in normal mode by following step 7.

  Method 2:

  1 run a scan for viruses on the computer safe mode with networking to make sure that the computer is virus-free.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Safety Scanner WARNING: There could be a loss of data while performing an analysis using the Microsoft safety scanner to eliminate viruses as appropriate.

  2. run the malware removal tool from Microsoft.

  Microsoft Malicious - 32-bit removal tool
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

  Microsoft Malicious removal tool - 64 bit
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=en

  Hope this information is useful.

• How can I get my printer spooler running I get error 1075 when I try to start it

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  If you see something like this:

  Cannot start service on Local computer print spooler.
  Error 1075: The dependency service does not exist or has been marked for deletion.

  Error 1075 means "ERROR_SERVICE_DEPENDENCY_DELETED".

  This means that there is some Service think that it depends on to start the Print Spooler Service that is missing.  It's maybe the printing or drivers that have been uninstalled software.

  If really, the dependency service exists and simply not work (dependence, Services must be started and running), you will get an error like this:

  Cannot start service on Local computer print spooler.
  Error 1068: The dependency service or group could start.

  You now or you already had all of the installed Lexmark printers?

  If the Service print spooler used to work well, do you have added or removed all printers since he worked?

  To view your Services, click Start, run and enter in the box:

  services.msc

  Click OK to open the Services Applet.

  Highlight the Print Spooler Service, right-click and choose properties you can see what is happening.  You will be especially interested in the startup (generally set to automatic) type and the items listed in the Dependencies tab.

  Always print spooler Service usually depends on the remote procedure call (RPC) Service is running, so if the remote procedure call (RPC) Service is not running, find it in your Services, launch it and set the startup type to automatic.

  If the remote procedure call (RPC) Service is not listed as a dependency for the Print Spooler Service, you can add it.

  You must see what Services depends on your Print Spooler Service, and then restart them (and their startup type automatic value), or if you have the dependency Services listed for items that are more installed on your system, you must inform the print spooler that she needs more of them to start.  Registered Addiction Services that are no longer needed must be removed.

  For example, I said to my Print Spooler Service depends on the remote procedure call (RPC) Service, and also depends on the Service Jose (and of course there is no Jose service).

  When I try to start my Print Spooler Service, I get an error 1075.  It's logical.

  If I look at the Print Spooler Service properties Dependencies tab in the applet Services however, it does not list the Jose Service as a dependency, but if I query the Print Spooler Service broken from a command prompt, I can see what ir really depends on to start and it looks like this:

  [SC] GetServiceConfig SUCCESS

  Service_Name: Spooler
  TYPE: 110 WIN32_OWN_PROCESS (interactive)
  STARTUP TYPE: 2 AUTO_START
  ERROR_CONTROL: 1 NORMAL
  BINARY_PATH_NAME: C:\WINDOWS\system32\spoolsv.exe
  LOAD_ORDER_GROUP: SpoolerGroup
  TAG                               : 0
  Display_name: Print spooler
  DEPENDENCIES: rpcss
  Jose
  SERVICE_START_NAME: LocalSystem
         
  I need to delete the Service jose as a dependency for the Print Spooler Service (and leave just the rpcss Service), then the Print Spooler Service will start.

  If you don't see the problem in the Print Spooler service dependencies tab, see what are actually of a command prompt window Print Spooler Service dependencies.  To do this, click on start run and in the type box:

  cmd

  Click OK to open a command prompt window.

  In the command prompt window, query the spooler to print (spooler) Service by entering the following command:

  sc qc spooler

  Whatever it is listed under needs of DEPENDENCIES is running before starting the print spooler.

  If there are DEPENDENCIES listed for things that are more installed, you can fix it, but first of all, we need to know what is indicated, then we can remove the ones that are not needed.

  If you make adjustments, do not forget to restart your system and make sure that changes "stick".

  Do, or do not. There is no test.

  Someone please tell me how to make figgy pudding like these kids keep saying they won't until they get some.

  I decided to implement the points for a new puppy instead of a pony!

• Why do I get an error msg when I try t send a msg via windows live

  When I try to years has add on craigslist, I get a msg that mail has failed?

  View all Windows Live questions in the appropriate forum:
  http://windowslivehelp.com/

• HP psc 2175 all-in-one 'internal unexpected error"msg when I try to scan

  I've uninstalled and reinstalled the driver three times as well as restarting the program and my PC and I still have this error. I get the error no matter what program, I am trying to scan to.  However, I can copy documents so the scanner works - it just won't ommunicate to other software programs.

  When I ran the HP print and Scan doctor, I was instructed that the driver is unable to communicate with the product, but this has not been resolved by uninstalling & reinstall the driver such as already mentioned.

  He said also the "Twain" component may be damaged and a problem was found with the HP Digital Imaging Monitor.  Still, the uninstalling/reinstalling does not fix this problem.

  Help!

  Hello, SEF,

  You can try the steps of a solution in this document:

  http://support.HP.com/us-en/document/c01162234

  If the problem persists after you perform the steps described in the document, try to scan via printers & faxes if you have Windows XP or devices and printers, if you have Windows 7/8. You can find it via the control panel. Here, you should have an icon for the scanner PSC 2175 (he probably called something like PSC 2170 series).

  Kind regards

  Pontus.

• Google error msg when I try to sign out of hotmail

  When I try to log out hotmail (I use Google Chrome) I get the message: "msn hmit logout". How can I fix it?

  Hello RRayXX,

  The best place to ask your question of Windows Live is inside Windows Live help forums. Experts specialize in all things, Windows Live, and would be delighted to help you with your questions. Please choose a product below to be redirected to the appropriate community:

  Windows Live Mail

  Windows Live Hotmail

  Windows Live Messenger

  Looking for a different product to Windows Live? Visit the home page Windows Live Help for the complete list of Windows Live forums to www.windowslivehelp.com.