HTTP does not not to PIX 515

Similar Questions

• Post cloning question: https does not

  Hi all

  I got (I hope) clone of the db layer and the layer of apps using clone fast.

  It's system rac db level at 2 knots, and so the application layer is a 2 nodes.

  When trying to load the https url, it does not load and displays "Internet Explorer cannot display the webpage"

  versions:

  EBS: 12.1.3 and db 11.2.0.2.

  Under files, settings:

  s_webentryprotocol is https

  s_login_page = https://ebsuat.domanin/OA_HTML/Appslogin

  s_enablesslterminator = no entrance!

  and s_active_webport = 443

  I believe that requires the above is all that's fixed at... What am I doing wrong here?

  Please see the following documents.

  The use of Oracle 11 g Release 2 Real Application Clusters with Oracle E-Business Suite Release 12 [823587.1 ID]

  Cloning of Oracle E-Business Suite Release 12 RAC systems compatible with the Rapid Clone [ID 559518.1]

  An "Internet Explorer cannot display the webpage" error, please check that apache save files as well as the details in the application.log file.

  Please also confirm that AutoConfig completed successfully on all nodes of the layer.

  Thank you

  Hussein

• HTTP does not work, but https

  I can't open any website, http and https.

  In safe mode, http works well as https.

  There is no proxy

  The process 'sh /etc/change_net_settings.sh' do.

  Remove/etc/pf.conf.

• sites http does not yet connect will connect to https sites

  locations of https:// as for bank cards, mortgage company, etc. to connect as expected.  But, http:// sites get the message "Internet Explorer cannot display the webpage"

  I tried to reset all the IE / Tools / Internet Options settings but no change in the results.

  I ran Malwarebytes, Symantec, mechanic sign up but all without success.

  Thank you

  You may have missed something in your research to solve this problem, read the information below; or try THE Forum:

  See if the information below helps you solve the problem/s you have with Internet Explorer:

  http://support.Microsoft.com/default.aspx/KB/936213/?p=1

  "How to optimize Internet Explorer"

  Configuration in Windows Internet Explorer 7 and Windows Internet Explorer 8 settings can cause one or more of the following problems:

  ·    You experience performance issues in Internet Explorer.

  ·    You receive an error message in Internet Explorer. For example, you receive a message error "Internet Explorer cannot display the webpage".

  ·    Internet Explorer stops responding.

  This article describes how optimize or reset Internet Explorer in Windows Vista to solve these problems.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://support.Microsoft.com/kb/936215

  "How to solve the problems of Internet Explorer in Windows Vista and Windows XP"

  This article explains how to solve any problems that you may experience when you use Windows Internet Explorer 7 or Windows Internet Explorer 8 on a computer that is running Windows Vista.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://support.Microsoft.com/kb/936214/

  "How to solve compatibility problems that affect Internet Explorer 7 in Windows Vista"

  This article describes how to troubleshoot software compatibility affecting Windows Internet Explorer 7. To help determine which program may be the cause of the problem, you can do the following:

  1 use the mode safe mode with networking

  2. perform a clean boot

  3. use another user account

  4 scan your computer against viruses and spyware

  5. run Internet Explorer 7 in "no Add-ons" mode

  Hope the above helps.

  ·                        ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Also try the Forum from IE:

  http://social.answers.Microsoft.com/forums/en-us/InternetExplorer/threads

  They will help you with your question IE in Forum Internet Explorer above.

  See you soon.

  Mick Murphy - Microsoft partner

• PeopleSoft on https does not

  Hello

  I installed the PIA and assigned to the Http port 8080 and 8081 to https port.

  I can able to properly connect to peoplesoft with http connect, however when I try to connect via https I'm mistake can test.

  URL used:
  http://rbdpsas211.rpd.cmp.com:8080/psp/TEST /? cmd = login & languageCd = FRA -> works very well
  https://rbdpsas211.rpd.cmp.com:8081/psp/TEST /? cmd = login & languageCd = FRA -> (error-> Internet Explorer cannot display this webpage)

  Any help on this is much appreciated.

  Thank you!
  Jean-Marc

  It seems a firewall problem.

  Thank you

  Jean-Marc

• Example of BrowserFieldDemo (OS 4.5) using the connection Https does not redirect events

  
  

  I had the events of redirection using processConnection callback

• HTTPS and PDM on a PIX 515

  I tried to connect to my pix vai the web page and I could not.

  I tried Https://192.168.1.1 but I wasn't happy.

  My question is:

  Do I need to have Java or any other software installed on my WEB interface prior PC between my PC and the PIX.

  Thank you

  Hi vitancr,

  your PDM version is compatible with your IOS? Otherwise, you can download a version that is compatible...

  Another important thing allows http, what you already have...

  Try again with another laptop or PC using the same IP address... maybe there is a problem with this PC... it can happen sometimes...

  all the best...

• HTTPS access to the router does not work with Firefox 33.0

  HTTPS access to the router Linksys wrt610n has worked so that Firefox 32.0.3 the dd - wrt software of this router is self-signed certificate with the public key RSA = 512 bits (Yes, it's too short today). From Firefox 33.0 and whose 34, 35, 36-access https does not work. It is desirable to restore https behavior as in Firefox 32.0.3 (with warning and ability to do security exception). Please see the attachment with a https query result in different versions of Firefox.
  Thank you.

  Hello, make suggestions to the https://support.mozilla.org/en-US/questions/1038487 help in your case?

• Created desktop shortcuts Internet does not

  Error message reads as follows; "The"https"Protocol was not a registered program.

  Hello

  Thanks for posting your question on the Microsoft community.

  Thank you for details on the issue.

  This problem may occur when the "https" Protocol is not associated with a program or a browser like Internet explorer.

  I suggest you use the steps in this article and check if that helps.

  Reference:

  Change the programs that Windows uses by default
  http://Windows.Microsoft.com/en-us/Windows/change-default-programs#1TC=Windows-7

  Please also set Internet explore as your default program.

  A default program is the program used by Windows when you open a particular type of file, such as a music file, an image, or a Web page.

  For reference, see suggestions of Don Varnau replied on 6 April 2012.
  http://answers.Microsoft.com/en-us/IE/Forum/IE9-windows_other/the-Protocol-HTTP-does-not-have-a-registered/d57184e5-1427-4ceb-b79c-0b26526974b1

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• PDM with PIX 515 does not work

  I just upgraded our PIX 515 of 6.1 to 6.2. I also added support FOR and loaded the version 2.1 of the PDM. I am trying to browse the MDP, but I can't. What Miss me?

  Hello

  have you added the following lines to your config file and have you used HTTPS to access the pix (http is not taken in charge, only https)?

  Enable http server

  http A.B.C.D 255.255.255.255 inside

  A.B.C.D is the ip address of the host from which you are trying to reach the pix with the pdm.

  If you're still having problems after the addition of these two lines, you might have a look at this page:

  http://www.Cisco.com/warp/customer/110/pdm_http404.shtml

  Kind regards

  Tom

• PIX 515 does not recognize the DIMM 128 MB

  PIX 515 does not recognize the DIMM 128 MB. Won't recognize only 32 MB. Also when the upgrade to 7.0, I get an error message that it has not enough flash, but I have 16 MB of flash needed.

  PIX 515 not recognizing 128 MB may be due to, in my opinion, pix-515 supports 64 MB. PIX-515e can support 128 MB. Now error Pix by reading not enough flash I got the same message when I tried to load 7.0 release using the tftp with padding interface configured to the local network with an attached TFTP server segment. I then tried the interruption during the startup control method, once the PIX reached ROMMON > issue 'auto of e1 interface', 'address 10.0.0.1', server 10.0.0.2, there are a few other commands. You may be familiar with them, otherwise use find under cisco.

  HTH

• PIX - 515 does not identify Tokenring Interfacecard

  Hello

  I installed a PIX-1 TR interface in the PIX 515. Start ok, 'answer' no configuration. SH LVE and sho int etc. presents only the build Ethernet0 and Eth1 but no interface tokenring.

  HS release looks like as follows.

  Thanks Ruedi

  pixfirewall # sh ver

  Cisco PIX Firewall Version 6.2 (2)

  Cisco PIX Device Manager Version 2.0 (2)

  Updated Saturday, June 7 02 17:49 by Manu

  pixfirewall until 10 mins dry 14

  Material: PIX - 515, 32 MB RAM, Pentium 200 MHz processor

  I28F640J5 @ 0 x 300 Flash, 16 MB

  BIOS Flash AT29C257 @ 0xfffd8000, 32 KB

  0: ethernet0: the address is 0003.6bf6.a8a9, irq 11

  1: ethernet1: the address is 0003.6bf6.a8aa, irq 10

  Features licensed:

  Failover: disabled

  VPN - A: enabled

  VPN-3DES: disabled

  Maximum Interfaces: 3

  Cut - through Proxy: enabled

  Guardians: enabled

  URL filtering: enabled

  Internal hosts: unlimited

  Throughput: unlimited

  Peer IKE: unlimited

  Serial number: 405341167 (0x182903ef)

  Activation key running: xxxxxxxxx

  Modified configuration of enable_15 to 13:11:47.490 UTC Tuesday, December 23, 2003

  pixfirewall #.

  Hello

  Token-Ring is no longer supported, I think since version 6.0.

• PIX and ASA static, dynamic and RA VPN does not

  Hello

  I am facing a very interesting problem between a PIX 515 and an ASA 5510.

  The PIX is in HQ and has several dynamic VPN connections (around 130) and IPsec vpn remote works very well. I had to add a PIX to ASA L2L VPN static and it does not work as it is supposed to be. The ASA 5510, at the remote end, connects and rest for a small period of time, however, all other VPN connections stop working.

  The most interesting thing is that ASA is associated with the dynamic map and not the static map that I created (check by sh crypto ipsec his counterpart x.x.x.x). However, if I make any changes in the ACL 'ACL-Remote' it affects the tunnel between the PIX and ASA.

  Someone saw something like that?

  Here is more detailed information:

  HQ - IOS 8.0 (3) - PIX 515

  ASA 5510 - IOS 7.2 (3) - remote provider

  Several Huawei and Cisco routers dynamically connected via ADSL

  Several users remote access IPsec

  A VPN site-to site static between PIX and ASA - does not.

  Here is the config on the PIX:

  Crypto ipsec transform-set ESP-3DES-ESP-SHA-HMAC-IPSec esp-3des esp-sha-hmac

  Dyn - VPN game 100 Dynamics-card crypto transform-set ESP-3DES-ESP-SHA-HMAC-IPSec

  Crypto dynamic-map Dyn - VPN 100 the value reverse-road

  VPN - card 30 crypto card matches the ACL address / remote

  card crypto VPN-card 30 peers set 20 x. XX. XX. XX

  card crypto VPN-card 30 the transform-set ESP-3DES-ESP-SHA-HMAC-IPSec value

  VPN crypto card - 100 - isakmp dynamic Dyn - VPN ipsec

  interface card crypto VPN-card outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  crypto ISAKMP policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  access list ACL-remote ext ip 10.0.0.0 allow 255.255.255.0 192.168.1.0 255.255.255.0

  Thank you.

  Marcelo Pinheiro

  The problem is that the ASA has a crypto acl defined between host and network, while the remote end has to the network.

  Make sure that the acl is reversed.

• D810 new camera appearing does not pix in raw files into components 11

  D810 new camera appearing does not pix in raw files into 11 elements and lightroom 4

  8.7 DNGC can be found here: http://www.adobe.com/downloads/updates/

  You can buy upgrades for LR or PES, here:

  http://www.Adobe.com/products/catalog/software._sl_id-contentfilter_sl_catalog_sl_software _sl_mostpopular.html

• Https: / specific page does not load after udate to 38.05

  https://my.albertahealthservices.ca
  does not load after update of 38.05 on my desk.

  I tried it on my laptop and it will load BUT after having been undated to 38.05 also failed to load this page.

  Other secure pages (Bank) loading OK

  Works well in Chrome and IE

  Error message:
  The secure connection failed

  The connection to my.albertahealthservices.ca while the page is loading.

     The page you are trying to view cannot be shown because the authenticity of the received data could not be verified.
     Please contact the website owners to inform them of this problem.
  

  Thank you
  Brian

  The site may attempt to return to a lower version of TLS in a way that is no longer allowed in current versions or maybe use a deprecated suite of encryption.

  You can open the topic: config page through the address bar and use the search bar to locate this pref:

  • Security.TLS.insecure_fallback_hosts

  You can double-click the line to edit the prefs and add the FQDN (my.albertahealthservices.ca) to the value of this preference.
  If there are already websites (domains) in this list, then add a comma and the new domain (without space).
  There should be only areas separated by a comma in the column value (example.com,www.example.com).

  If this help you can contact this Web site and ask them to look into this and update their security.

  • https://developer.Mozilla.org/en-us/Firefox/releases/36/Site_Compatibility#security
  • https://developer.Mozilla.org/en-us/Firefox/releases/37/Site_Compatibility#security
  • https://developer.Mozilla.org/en-us/Firefox/releases/38/Site_Compatibility#security