HWIC-AP
Hi all.
I have an HWIC-AP on a configured 2801 like this:
interface Dot11Radio0/3/0
10.1.2.1 IP address 255.255.255.0
no ip-cache cef route
no ip route cache
!
SSID ordered
open authentication
Comments-mode
!
base speed - 1.0 2.0 basic basic-5, 5 6.0 9.0 basic-11, 0 12.0 18.0 24.0 36.0 48.0 54.0
root of station-role
And the DHCP server looks like this:
dhcp WLAN IP pool
Network 10.1.2.0 255.255.255.0
10.1.2.1 - default router
Server DNS XXX XXX
A wireless client can successfully connect to the radio and gets an IP address from the pool, but cannot access the internet or other local networks VIRTUAL resources. Wireless devices must be in their own subnet.
Do I have to configure address?
Thank you for any help or examples.
Marc
Hosts on other VLANs can talk to each other (i.e., VLAN-to-VLAN)?
Can other guests out to the Internet ok?
It would help if you could post your complete (sterilized) config.
If you configure bridging inter - vlan, it is almost the same as not no VLANS at all... VLAN is to separate broadcast domains, the bridges connect / join / merge broadcast domains.
This looks like a thing of routing or addressing. OR you may need to associate the group with one of the routed interfaces wireless bridge.
You may also at your disposal for configuration GUI... try aiming a browser on the router and see options to come.
Post your configs.
Good luck
Scott
Tags: Cisco Wireless
Similar Questions
-
HWIC-AP more Call Manager Express?
It took me some time and many transfers of tftp to finally find an IOS which works very well with the HWIC-AP (wireless access point module) for a router in 2801.
What I was asking: is there an IOS which supports both HWIC-AP and also includes the Call Manager Express (CME)?
What feautures would you find using the IOS search engine?)
Thanks for all the ideas.
Marc
Use the IOS 12.4 (2) T1 or later to support the CME and HWIC-AP
-
Will be the use of one or the other HWIC-APs allow speeds of access connections 108Mbs with a G wireless client?
Hi Randall,.
Unfortunately not. The number 108Mbs is the combinaton of 802.11 g and 802. 11 data, and flow with subtraction due to overload, the actual rate is much lower. Take a look;
Comparison of approximate throughput for 802. 11A, 802. 11B and 802.11 g
802. 11b data Rate (Mbit/s) = 11 approximate throughput (Mbit/s) = 6
802.11 g (No 802 11b clients in the cell) Data Rate (Mbit/s) = 54 approximate throughput (Mbit/s) = 22
802. 11A data Rate (Mbit/s) = 54 approximate throughput (Mbit/s) = 25
Since this great doc.
http://www.Cisco.com/en/us/products/HW/wireless/ps430/products_white_paper09186a00801d61a3.shtml
I hope this helps!
Rob
-
I have a questions my router 2911 programming with a map hwic-4t 1/e1 for three bonded t1 with ppp.
The router and the Hwic are fresh out of the box. I have a very simple setup. I have 3 lines leased t1 bonded through AT & T to Time Warner Telecom router using xxx.xxx.xxx.x45 at their end and xxx.xxx.xxx.x46 for my dissertation.
I installed the Hwic and then did these activation orders and to set up to work with them as I was told:
(Basic...)
> activate
#config t
main g) #hostname
g) #no ip domain-lookup
(SSH...)
password g) #username
main.com g domain name) #ip
generate g) #crypto rsa key
g) #512
g) #ip ssh worm 2
g) #line vty 0 5
local line) #login
line) #transport of entry ssh
line) #exit
(install hwic)
#card g) type t1
g) #network - clock - participate wic 0
(config hwic controllers)
g) #controller T1 0/0/0
er) #faming ESF
B8ZS er) #linecode
er) #Fdl att
er source line) #clock
ESF distance line er) #loopback
#cablelength er) short-110
er) #crc - threshold 320
detection of er) yellow #no
er) #exit (repeated for 0/0/1 and 0/0/2)
(internal interfaces)
g) #int g0/0
f) #ip address 10.0.0.254 255.25.255.0
f stop) #no
(Destination of last resort)
g) #ip route 0.0.0.0 0.0.0.0 xxx.xxx.xxx.x45
(multilink ppp Panel)
g) #int 1 multilink Panel
f) #ip add xxx.xxx.xxx.x46 255.255.255.252 (I get an error saying here that it overlaps a static route in the routing table). (so it does not accept it)
f) #no cdp enable
f) #ppp multilink Panel
multilink Panel group f) #ppp 1
f) #exit
(Adding interfaces to a Multilink Group 1)
g) #int T1 0/0/0 (I get an error saying here an entry not valid 1 0 0/0/0) (so I tried 'int T1?' and all I get is
then I tried "interface?" to see all possible interfaces and all I get are: Async, Auto-modele, BVI, CDMA-Ix, CTunnel, Dialer, Embedded-service-engine, GigE, group async, LongReachEthernet, looping, LIM, Multilink, Null, Port Channel, Tunnel, KEEN, Pseudowire virtual-PPP, model-Virtual, virtual-TokenrRing, vmi range
-At this point I don't know what to do? I had expected:
g) #int T1 0/0/0
f) #no ip address
f) #encap PPP
f) #no fair-queue
f) #ppp multilink Panel
multilink Panel group f) #ppp 1
f) #exit
(repeated for 0/0/1 and 2/0/0, but obviously if I can't do it in the configuration interface, I can't put these commands)
-So I went NAT...
g) #access - list 5 permit 10.0.0.0 0.0.0.255
g) #ip nat inside interface 5 source T1 0/0/0 overload list (obviously it did not work, so I tried 'ip nat inside source list 5 interface t1 overload')
-He took but I think it has something to do with? tunnel? (I do not really understand the tunnels)
g) #int g0/0
f) #ip nat inside
f) #exit
g) #int T1 0/0/0 (even once did not work so I used "int T1" and it took)
f) #ip nat outside
# exit f)
In each controller interface add "hours of channel-group 0 1 - 24.
This will create serials. Configure each of
No ip addr
ENCAP PPP
Multilink PPP
Multilink PPP 1 Panel groupOn int 1 multilink Panel Add your IP address, multilink PPP and multilink ppp Group 1 Panel
Sent by Cisco Support technique iPad App
-
Cisco 2911 + 3 G-HWIC-HSPA
Hi guys,.
I am trying to configure this module first time in my life and ran into a problem.
When I do it, "display cell security x/x/x ' it keeps reports my SIM status as deleted. I reinstalled several times now, and now I'm starting to think that the micro SIM will not be managed by this module.
No one knows about it? It is hard to find on google, spent the last hour of some research on it. I could find only this document Cisco:
Taking SIM card; in accordance with the standard ISO-7816-2 (mechanical SIM)
And an example configuration would be much appreciated.
Thanks in advance,
JI
You use a correct micro-sim adapter?
-
Problem starting the Cisco 2821 router
Hello world
I have cisco 2821 router. I am facing problem starting.
someone suggest me what is the problem.
Thanks in advance...
VERSION of the SOFTWARE system Bootstrap, Version 12.4 (13r) T, (fc1)
Technical support: http://www.cisco.com/techsupport
Copyright (c) 2006 by cisco Systems, Inc.The ECC memory initialization
.
C2821 platform of 262144 KB of main memory
Main memory is configured for 64-bit with ECC activeReadOnly initialized ROMMON
load complete, point of entry to the program: 0x8000f000, size: 0xcb80
load complete, point of entry to the program: 0x8000f000, size: 0xcb80load complete, point of entry to the program: 0x8000f000, size: 0x26bc2cc
Decompression of self-image: #.
################################################################################
################################################################################
################################################################################
################################################################################
################################################################# [OK]Smart init is enabled
Smart init is sizing iomem
MEMORY_REQ TYPE ID
0003E8 0X003DA000 C2821 Mainboard
1A 0X0025178C E3 0001AB
0X00263F50 VPN on board
0X000021B8 embedded USB
Swimming pools public buffer 0X002C29F0
Swimming pools public particle 0 X 00211000
TOTAL: 0X00D65284If all memory conditions above are
"UNKNOWN", you could use a non supported
configuration or there is a software problem and
the system may be compromised.
Rounded IOMEM to: 14 MB.
Using iomem of 5 percent. [14 mb / 256Mb]Legend restricted rights
Use, duplication, or disclosure by the Government is
subject to such restrictions as set out in paragraph
(c) Commercial - limited computer software
The rights to FAR clause 52.227 - 19 and subparagraph s
(c) (1) (ii) rights to technical and computer data
Clause of DFARS 252.227 - 7013 section software.Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706Cisco IOS software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4 T7 (9)
Version of the SOFTWARE (fc3)
Technical support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Last updated Friday, January 10 08 16:35 by prod_rel_team
Image text-base: 0x400B1E74 database: 0x434A9AC0ERROR detected on Bus PCI1
Try REINSTALLING all the modules in the system
pci1_int_cause 0 x 00000240,
pci1_err_addr 0 x 00091009, pci0_err_cmd 0x0000000A
PCI Master Read parity error
Abort target PCIR0 = r1 = r2 FFFFFFFF FFFFFFFF = 0 r3 = 45 80000 r4 = 0
R5 = 303 r6 = 0 A7 = 1 = 0 = 100000 r9 r8
R10 = 0 r11 = 465E4369 r12 = 0 r13 = 465E436A r14 = 0
R15 = r16 r17 8 = 0 = C100 r18 = 0 r19 3400 101 =
R20 = r21 0 = 40096828 r22 = FFFFFFFF r23 = r24 FFFF00FF = 0
R25 = 469AAC64 r26 = 0 = 469AAC60 r28 = 0 = 469AAC5C r29, r27
R30 = 0 r31 = 469AAC58 r32 = r33 FFFFFFFF = r34 = FFFFFFFF FFFFFFFF
R35 = r36 = r37 = r38 = r39 FFFFFFFF FFFFFFFF FFFFFFFF FFFFFFFF = FFFFFFFF
R40 = FFFFFFFF = FFFFFFFF = FFFFFFFF = FFFFFFFF r44 r43 r42 r41 = FFFFFFFF
R45 = r46 = r47 = r48 FFFFFFFF FFFFFFFF FFFFFFFF = r49 0 = 469AACD0
R50 = 0 0 = 0 r53 r51 = r52 = 3040A 801 r54 = FFFFFFFF
R55, r56 = FFFFFFFF = FFFFFFFF r58 r57 A000F000 = = 0 = 465E4358 r59
R60 = r61 = r62 FFFFFFFF FFFFFFFF = r63 = 0 402E4B10
GENS = 3400 103 mdlo_hi = my 0 = 251 00
mdhi_hi = 0 = 0 badvaddr_hi = FFFFFFFF mdhi
BadVAddr = cause = epc_hi 0 = FFFFFFFF FFFFFFFF
EPC = 402E4B08 err_epc_hi = err_epc FFFFFFFF = FFFFFFFFERR-1-FATAL %: interruption of the fatal error, reload
err_stat = 0 x 0= Posts from Flushing (02: 37:51 UTC Wednesday, may 18, 2016) =.
Messages in queue:
02:37:51 UTC Wednesday, may 18, 2016: interrupt exception, signal CPU 22, PC = 0 x 0
--------------------------------------------------------------------
Software fault possible. On reccurence, you perceive
crashinfo, 'show tech' and contact Cisco Technical Support.
---------------------------------------------------------------------Trace =
$0: 00000000, AT: 00000000, v0: 00000000, v1: 00000000
A0: 00000000, a1: 00000000, a2: 00000000, a3: 00000000
T0: 00000000, t1: 00000000, t2: 00000000, t3: 00000000
T4: 00000000, t5: 00000000, t6: 00000000, t7: 00000000
s0: 00000000, s1: 00000000, s2: 00000000, s3: 00000000
S4: 00000000, s5: 00000000, s6: 00000000, s7: 00000000
T8: 00000000, t9: 00000000, k0: 00000000, k1: 00000000
GP: 00000000, sp: 00000000, s8: 00000000, ra: 00000000
EPC: 00000000, ErrorEPC: 00000000, GENS: 00000000
MY: 00000000, MDHI: 00000000, BadVaddr: 00000000
CacheErr: 00000000, DErrAddr0: 00000000, DErrAddr1: 00000000
DATA_START: 0X434A9AC0
Cause 00000000 (Code 0 x 0): Exception of interruptionWriting crashinfo in flash: crashinfo_20160518-023752
No reboot to warm storage
System received a system error *.
signal = 0 x 16, code = 0x0, context = 0 x 46905718
PC = 0x40096d7c, Cause = 0 x 20, State Reg = 0 x 34008002Software Cisco IOS, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4 (9)T7
Version of the SOFTWARE (fc3)OK, the router is running on a train of "T".
ERROR detected on Bus PCI1
Try REINSTALLING all the modules in the system
pci1_int_cause 0 x 00000240,
pci1_err_addr 0 x 00091009, pci0_err_cmd 0x0000000A
PCI Master Read parity error
Abort target PCIRemove any all NM/NME or WIC/HWIC cards and restart again. If the router is able to start properly, upgrade the router to a higher version. DO NOT use another "T" train if it is needed. Use instead a train of "M".
-
WIC T1-1DSU vs VWIC2-1MFT-T1/E1
Hi all
I'm looking at a router of production with a VWIC2-1MFT-T1/E1 module, and none of the two parts of the serial p2p connection configurations of clock rate. Now I know, the VWIC2-1MFT-T1/E1, everything is configured under the controller interface. However I don't see any orders as with the WIC-1DSU clock rate. How does this work? Does this mean that there is a CDU/CSU at this place? I'm just used to seeing the WIC-1DSU-T1 more and have not worked with before multiflex modules.
Thank you
Hello
If you have a WIC-1DSU-T1, WIC-1DSU-T1-V2 or HWIC-1DSU-T1, you pass under the clock interface source configuration and type of service-module t1:
3845_2 (config) #int serial 0/1/0
3845_2(Config-if) clock t1 source #-service module?
clock use internal adapter
clock to recover the line
You have 2 options here as you can see. Internal provides synchronization and line gets by synchronizing. In a circuit back to back, it is recommended to configure one end as 'internal', while the other is "online". If your provider is in the middle to provide synchronization for both ends, the configuration of the 'line' is recommended, but it depends on the specifications of the circuit. You can use the "show-service module" (don't forget the counters to see compensation costs statistics) command to see if there are synchronizing issues. Basically, you need to focus on the 'Dry' value, this leaflet. If it increases, it is recommended to check if the synchronization is correctly configured. Sometimes you need to get the vendor involved to confirm the right configuration of synchronization, you should have.
On the other hand, if you have a VWICX-XMFT-T1/E1 you must enter in the configuration of the controller and choose the right configuration of synchronization. It works essentially the same as in a WIC-1DSU-T1 hardware and similar.
T1 #controller 3845_1 (config) 0/0/0
3845_1(config-Controller) source of #clock?
race free Free Running Clock
Internal clock
recovered clock line
"The keyword which indicates a clock of free-running from the oscillator on the motherboard, which is used only for testing and back-to-back connections".
http://www.Cisco.com/en/us/docs/iOS/12_2/12_2z/12_2zj/feature/guide/gthwecan.html
To search for statistical use of the "show controllers t1 X/X/X" command and avoid using any command "loopback" so that it would affect the connection because it is used only for testing purposes. I hope this information helps and do not forget to note the useful messages.
Kind regards.
-
Cisco 877W DHCP does not automatically fill the Windows/Mac customers with DNS server entries
I have a 877W which was operational on Verizon for about 5 years. It never automatically distributed info DNS server for customers who get DHCP issued IP address. I have to manually enter the DNS entries to each client. What happened to other sites where I've got installed on AT & T as well as 877 unified communications.
Here is the config. Thanks in advance for the help.
Building configuration...
Current configuration: 7987 bytes
!
version 12.4
no service button
tcp KeepAlive-component snap-in service
a tcp-KeepAlive-quick service
horodateurs service debug datetime localtime show-timezone msec
Log service timestamps datetime localtime show-timezone msec
encryption password service
sequence numbers service
!
Cod of hostname
!
boot-start-marker
boot-end-marker
!
logging buffered debugging 51200
recording console critical
enable secret 5 jSwA $1$ $ 3B5lJNqm0ewh
!
AAA new-model
!
!
AAA authentication local-to-remote login
local remote of the AAA authorization network
!
AAA - the id of the joint session
!
resources policy
!
PCTime-6 timezone clock
PCTime of summer time clock day April 6, 2003 02:00 October 26, 2003 02:00
IP subnet zero
IP cef
No dhcp use connected vrf ip
DHCP excluded-address IP 192.168.7.1 192.168.7.19
DHCP excluded-address IP 192.168.7.70 192.168.7.254
!
IP dhcp pool sdm-pool1
import all
network 192.168.7.0 255.255.255.0
router by default - 192.168.7.1
DNS-server 68.238.96.12 68.238.112.12
!
!
inspect the IP name DEFAULT100 cuseeme
inspect the IP name DEFAULT100 ftp
inspect the IP h323 DEFAULT100 name
inspect the IP icmp DEFAULT100 name
inspect the IP name DEFAULT100 netshow
inspect the IP rcmd DEFAULT100 name
inspect the IP name DEFAULT100 realaudio
inspect the name DEFAULT100 rtsp IP
inspect the IP name DEFAULT100 esmtp
inspect the IP name DEFAULT100 sqlnet
inspect the name DEFAULT100 streamworks IP
inspect the name DEFAULT100 tftp IP
inspect the tcp IP DEFAULT100 name
inspect the IP udp DEFAULT100 name
inspect the name DEFAULT100 vdolive IP
synwait-time of tcp IP 10
IP domain name cods.com
name of the IP-server 68.238.96.12
name of the IP-server 68.238.112.12
property intellectual ssh time 60
property intellectual ssh authentication-2 retries
!
!
Crypto pki trustpoint TP-self-signed-437228204
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 437228204
revocation checking no
rsakeypair TP-self-signed-437228204
!
!
TP-self-signed-437228204 crypto pki certificate chain
certificate self-signed 01
30820254 308201BD A0030201 02992101 300 D 0609 2A 864886 F70D0101 04050030
2 060355 04031325 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 30312E30
69666963 34333732 32383230 34301E17 303731 30313632 33333131 0D 6174652D
395A170D 2E302C06 1325494F 03550403 32303031 30313030 30303030 5A 303031
532D 5365 6C662D53 69676E65 4365 72746966 69636174 652 3433 37323238 642D
06092A 86 4886F70D 01010105 32303430 819F300D 00308189 02818100 0003818D
BF73E16C 24A3FB0B A44C83C8 45ACEC75 163C2F0A 87836F7F A43FEB72 0EF26AFA
C7F35ED6 CBCC6853 5E82B0A6 1FD8020B F3630023 AB30B870 B3155EE6 86988910
4ACF5121 1CBFF4DC B705DF1E 5D0D698F 06493 D 3DD8D036 42 FE450D21 E26A4DAF
CE6BA806 81A9F451 0246698E DA7B49E3 160F115C E1104FA9 31FA3C15 CD 782 279
02030100 01A37E30 7C300F06 03551 D 13 0101FF04 05300301 01FF3029 0603551D
20821E63 11042230 6F64732E 6F666472 63697479 6E677370 69707069 72696E67
732E636F 6D301F06 23 04183016 24 D 77493 80142FA3 03551D 52CF7094 B847B6EB
1385E2E5 0F3A301D 0603551D 0E041604 142FA324 D7749352 CF7094B8 47B6EB13
85E2E50F 3A300D06 092 HAS 8648 01040500 03818100 076EE499 12F46D79 86F70D01
375B7EA6 C9279DA4 B32723B5 908C9FB8 D42CB978 BB24A8FE 73579A3D CA 5130, 87
B7716644 7E13710D C6E6360C D0A36F7B F62540E2 0C33523B E50396B9 2EF66FA7
56519E62 E55EAF3C E1D9BEC9 3AE67B59 75E61F06 B649E90A 2798F755 7A020F0A
F8BDABFA 1EE37B6A A918560D DA45AD70 801BC66E 94D1468E
quit smoking
username privilege 15 secret $5 1jgO$sGD@#l4yTtLtYoEZbh/Wl steal551.
!
!
door-key crypto vpn_ddaus
pre-shared key address 0.0.0.0 0.0.0.0 - key stealthfortyfor5
door-key crypto vpn_rmlfk
address of pre-shared-key 205.30.134.22 key stealthfortyfor5
!
crypto ISAKMP policy 10
md5 hash
preshared authentication
Group 2
!
crypto ISAKMP policy 30
BA 3des
preshared authentication
Group 2
invalid-spi-recovery crypto ISAKMP
ISAKMP crypto keepalive 20
!
Configuration group isakmp crypto VPNRemote client
key ConnectNow45
pool ippool
ISAKMP crypto vpnclient profile
VPNRemote identity group match
client authentication list for / remote
Remote ISAKMP authorization list
client configuration address respond
Crypto isakmp CODS_DDAUS profile
key ring vpn_ddaus
function identity address 0.0.0.0
Crypto isakmp CODS_RMLFK profile
key ring vpn_rmlfk
function identity address 205.30.134.22 255.255.255.255
!
!
Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
!
Crypto-map dynamic dynmap 10
Set transform-set RIGHT
vpnclient Set isakmp-profile
Crypto-map dynamic dynmap 12
Set transform-set RIGHT
CODS_DDAUS Set isakmp-profile
!
!
MYmap 1 ipsec-isakmp crypto map
defined by peer 205.30.134.22
Set transform-set RIGHT
CODS_RMLFK Set isakmp-profile
match address CODS_to_RMFLK
map mymap 65535-isakmp ipsec crypto dynamic dynmap
!
Bridge IRB
!
!
interface Loopback10
IP 1.1.1.1 255.255.255.0
!
ATM0 interface
no ip address
route IP cache flow
No atm ilmi-keepalive
DSL-automatic operation mode
!
point-to-point interface ATM0.1
Description $FW_OUTSIDE$ $ES_WAN$
Check IP unicast reverse path
inspect the DEFAULT100 over IP
NAT outside IP
IP virtual-reassembly
PVC 0/35
aal5snap encapsulation
!
Bridge-Group 2
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Dot11Radio0
no ip address
no ip-cache cef route
no ip route cache
!
encryption vlan 1 tkip encryption mode
!
SSID tsunami
VLAN 1
open authentication
authentication wpa key management
Comments-mode
WPA - psk ascii 7 14231A0E01053324363F363B36150E050B08585E
!
base speed - 1.0 2.0 basic basic-5, 5 6.0 9.0 basic-11, 0 12.0 18.0 24.0 36.0 48.0 54.0
root of station-role
!
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route cache
no link-status of snmp trap
No cdp enable
Bridge-Group 1
Bridge-group subscriber-loop-control 1
Bridge-Group 1 covering-disabled people
Bridge-Group 1 block-unknown-source
No source of bridge-Group 1-learning
unicast bridge-Group 1-floods
!
interface Vlan1
Description $ETH - SW - LAUNCH, INTF-INFO-HWIC $$ $4ESW $FW_INSIDE$
no ip address
IP tcp adjust-mss 1452
Bridge-Group 1
!
interface BVI1
Description $ES_LAN$ $FW_INSIDE$
192.168.7.1 IP address 255.255.255.0
IP nat inside
IP virtual-reassembly
route IP cache flow
IP tcp adjust-mss 1412
!
interface control2
IP 70.14.49.134 255.255.255.0
NAT outside IP
IP virtual-reassembly
crypto mymap map
!
local pool IP 10.10.10.1 ippool 10.10.10.254
IP classless
IP route 0.0.0.0 0.0.0.0 70.14.49.1
!
IP http server
local IP http authentication
IP http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
overload of IP nat inside source list 133 interface control2
!
CODS_to_RMFLK extended IP access list
IP 192.168.7.0 allow 0.0.0.255 192.168.1.0 0.0.0.255
!
recording of debug trap
access-list 1 permit 192.168.7.0 0.0.0.255
access-list 100 remark self-generated by the configuration of the firewall Cisco SDM Express
Access-list 100 = 1 SDM_ACL category note
access-list 100 deny ip 70.14.49.0 0.0.0.255 any
access-list 100 deny ip 255.255.255.255 host everything
access-list 100 deny ip 127.0.0.0 0.255.255.255 everything
access ip-list 100 permit a whole
access-list 101 permit ip 192.168.7.0 0.0.0.255 192.168.3.0 0.0.0.255
access-list 133 deny ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 133 deny ip 192.168.7.0 0.0.0.255 10.10.10.0 0.0.0.255
access-list 133 deny ip 192.168.7.0 0.0.0.255 192.168.10.0 0.0.0.255
access-list 133 deny ip 192.168.7.0 0.0.0.255 192.168.3.0 0.0.0.255
access-list 133 allow ip 192.168.7.0 0.0.0.255 any
not run cdp
mymap permit 10 route map
corresponds to the IP 111
set ip next-hop 1.1.1.2
!
!
control plan
!
Bridge Protocol ieee 1
1 channel ip bridge
Bridge Protocol ieee 2
IP road bridge 2
connection of the banner ^ CAuthorized access only!
Unplug IMMEDIATELY if you are not an authorized user. ^ C
!
Line con 0
no activation of the modem
telnet output transport
line to 0
telnet output transport
line vty 0 4
privilege level 15
transport input telnet ssh
!
max-task-time 5000 Planner
Scheduler allocate 4000 1000
Scheduler interval 500
endHello
Can you try to remove the IMPORT ALL of the dhcp pool
RES
PaulSent by Cisco Support technique iPad App
-
Dows routers Cisco 2921 supports WIC cards?
I have trouble to install a frame relay service, because the seller sold me the WIC cards but I think that 2921 only supports cards HWIC
Here the result to see the figure:
Router Llano Mall
ag321-VAC-rou-01 #sh diag | b WIC Slot 1:
WIC Slot 1:
Series 2T (12 in 1)
Module WIC unsupported / disabled this slot machine
Review of Board of revision 1.0 Hardware B0
Serial number 32098957 part number 800-03181-02
FRU part number WIC - 2T =
Test the number of RMA history 0 x 0 00-00-00
Type of PCI slot
Format EEPROM 1 version
Table of contents EEPROM (hex):
0 X 20:01 12 01 00 01 E9 CA 8 D 50 6 02 00 00 00 00 0C
0 X 30 : 58 00 00 00 04 04 08 00 FF FF FF FF FF FF FF FFRouter Cumaná
ag521-VAC-rou-01 #sh diag | b WIC Slot 0:
WIC Slot 0:
Daughter HWIC WAN card series 2T
Hardware revision: 2.0
Number of albums part together: 800-34379-01
Review on board: A0
Number of deviation: 115024
Fab version: 02
Serial number of PCB: FOC15023T8C
History of the RMA tests: 00
RMA number: 0-0-0-0
RMA history: 00
FAB part number: 28-8141-01
Product number (FRU): HWIC-2 t
Version identifier: V03
CLEI Code: COUIA1RCAB
EEPROM 4 format version
Table of contents EEPROM (hex):
0X00: 04 FF 40 05 89 41 02 00 C0 46 03 20 00 86 4 B 01
0X10: 42 41 30 88 00 01 50 02 02 C1 8B 46 43 31 4F C1
0x20: 35 30 32 33 54 38 43 03 00 81 00 00 00 00 04 000 X 30: 85 1 1F CD 01 87 48 57 49 43 2D 32 54 89 56 CB
0 X 40: 30 33 20 D9 02 40 C1 C6 8 A 43 55 49 41 31 52 4F
0 X 50 : 43 41 42 FF FF FF FF FF FF FF FF FF FF FF FF FF
0 X 60 : FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0 X 70 : FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FFIs there any command or any form can I use this card to put in place frame relay?
Thanks in advance
Alejandro
It seems that he has not supported and an ISR G2 2921 would accept an HWIC-2 t instead.
http://www.Cisco.com/en/us/products/ps10537/products_relevant_interfaces...
Sent by Cisco Support technique iPhone App
-
Cisco No. 2851 with 2 - FPS?
Hi all
First of all you wishing all happy new year!
I want to know if it is - it possible to connect 2-HWIC-SFP modules (1 GB) router Cisco No. 2851?
A single. See below (table 3).
High-speed Cisco Gigabit Ethernet WAN Interface Card
-
Cannot access internet connected pc
Hi all
I will have questions, how to get to the internet from the PC. It is currently connected to the cisco 877w via FE0.
The PC is able to enter the correct IP address. Even when I entered dns [8.8.8.8], I'm still not able to access the internet.
Joined the config-
================================
!
version 12.4
no service button
horodateurs service debug datetime msec
Log service timestamps datetime msec
encryption password service
!
router host name
!
boot-start-marker
boot-end-marker
!
!
No aaa new-model
!
!
dot11 syslog
IP cef
No dhcp use connected vrf ip
DHCP excluded-address IP 192.168.1.254
!
IP dhcp pool HOME-DHCP
import all
network 192.168.1.0 255.255.255.0
by default-router 192.168.1.254
Server DNS 8.8.8.8
!
!
no ip bootp Server
8.8.8.8 IP name-server
name of the IP-server 165.21.100.88
!
!
!
!
!
Archives
The config log
hidekeys
!
!
!
!
!
ATM0 interface
no ip address
No atm ilmi-keepalive
DSL-automatic operation mode
!
point-to-point interface ATM0.1
Description $ES_WAN$ $FW_OUTSIDE$
penetration of the IP stream
PVC 0/100
aal5snap encapsulation
Protocol ppp Dialer
Dialer pool-member 1
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Dot11Radio0
no ip address
Shutdown
base speed - 1.0 2.0 basic basic-5, 5 6.0 9.0 basic-11, 0 12.0 18.0 24.0 36.0 48.0 54.0
root of station-role
!
interface Vlan1
Description $ETH - SW - LAUNCH$ $INTF - INFO - HWIC-$4ESW $ES_LAN$ $FW_INSIDE$
IP 192.168.1.254 255.255.255.0
no ip redirection
no ip unreachable
no ip proxy-arp
penetration of the IP stream
IP nat inside
IP virtual-reassembly
IP tcp adjust-mss 1452
!
interface Dialer0
the negotiated IP address
no ip redirection
no ip unreachable
no ip proxy-arp
penetration of the IP stream
NAT outside IP
IP virtual-reassembly
encapsulation ppp
Dialer pool 1
Dialer-Group 1
No cdp enable
PPP authentication pap callin
PPP pap sent-username [email protected] / * / 7 130 44185206173829 password
!
IP forward-Protocol ND
IP route 0.0.0.0 0.0.0.0 Dialer0
!
no ip address of the http server
no ip http secure server
!
!
!
!
control plan
!
!
Line con 0
no activation of the modem
line to 0
line vty 0 4
!
max-task-time 5000 Planner
end
Can you ping your router 8.8.8.8? If so, you'll need is to configure the nat on the router:
access-list 100 permit ip 192.168.1.0 0.0.0.255 any
IP nat inside source list 100 interfaces dialer0 overload
int vlan 1
IP nat inside
int dial0
NAT outside IP
HTH,
JohnPlease note all useful messages *.
-
I'm losing configuration when I turned off my Cisco 857 router
I bought the new router Cisco 857 of the shop. Router must have been used before as I couln can't go inside with name of user and password default cisco/cisco.
Well I followed digital and reset the password for the user name and password. Now I have finally connected to Cisco CP express on my IE browser.
I discovered that someone was using a router in the shop that's why I countries: ' t log in to him in the first place. In any case the problem is that when I changed my configuration and applies the settings he remembers until I turned off. When I turn on again he remembers all the parameters of this shop.
He returned everything back: IP address, former account to level 15 and password - just like after the password reset.
I tried again and he again lost the settings. So I found instructions:
http://www.Cisco.com/en/us/products/HW/routers/ps233/products_tech_note09186a00800a65a5.shtml
I followed it and changed once again all the settings of the router. My settings are still lost after the power on/off. I noticed that when I do everything first bit it shows
0x2102 not 0x2142 like they think that is password reset mode.
Here is my output from Hyper Terminal:
=============================
Cisco#enable
Cisco#show start
Using 3359 out of 131072 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Cisco
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 warnings
enable secret 5 $1$hpKF$Rc1tl6r45J8iHG7EN5jSk.
!
no aaa new-model
!
crypto pki trustpoint TP-self-signed-3185909327
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3185909327
revocation-check none
rsakeypair TP-self-signed-3185909327
!
!
crypto pki certificate chain TP-self-signed-3185909327
certificate self-signed 01 nvram:IOS-Self-Sig#5.cer
dot11 syslog
no ip dhcp use vrf connected
ip dhcp excluded-address 10.10.10.1
!
ip dhcp pool ccp-pool
import all
network 10.10.10.0 255.255.255.248
default-router 10.10.10.1
lease 0 2
!
!
ip cef
no ip domain lookup
ip domain name molinary.com
!
!
!
username admin privilege 15 secret 5 $1$jD3j$r6ROikgGsIlcMTGjkxFQ6.
username username privilege 15 password 0 password
!
!
archive
log config
hidekeys
!
!
!
!
!
interface ATM0
no ip address
shutdown
no atm ilmi-keepalive
dsl operating-mode auto
!
interface ATM0.1 point-to-point
description $ES_WAN$
ip nat outside
ip virtual-reassembly
pvc 0/38
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$ES_LAN$
ip address 10.10.10.1 255.255.255.248
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1452
!
interface Dialer0
ip address dhcp
encapsulation ppp
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication chap pap callin
ppp chap hostname [email protected]/* */
ppp chap password 0 netgear01
ppp pap sent-username [email protected]/* */ password 0 netgear01
!
ip forward-protocol nd
!
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list 1 interface ATM0.1 overload
!
access-list 1 remark INSIDE_IF=Vlan1
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 10.10.10.0 0.0.0.7
dialer-list 1 protocol ip permit
no cdp run
!
control-plane
!
banner exec ^C
% Password expiration warning.
-----------------------------------------------------------------------
Cisco Configuration Professional (Cisco CP) is installed on this device
and it provides the default username "cisco" for one-time use. If you have
already used the username "cisco" to login to the router and your IOS image
supports the "one-time" user option, then this username has already expired.
You will not be able to login to the router with this username after you exit
this session.
It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.
username
privilege 15 secret 0 Replace
and with the username and password you want to use.
-----------------------------------------------------------------------
^C
banner login ^CAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!^C
!
line con 0
login local
no modem enable
line aux 0
line vty 0 4
privilege level 15
login local
transport input telnet ssh
!
scheduler max-task-time 5000
end
Cisco#
Cisco#
Cisco#
Cisco#
Cisco#
Cisco#
Cisco#
Cisco#
Cisco#show version
Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, R
ELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Fri 22-Jan-10 14:46 by prod_rel_team
ROM: System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARE
Cisco uptime is 20 minutes
System returned to ROM by power-on
System image file is "flash:c850-advsecurityk9-mz.124-15.T12.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
Cisco 857 (MPC8272) processor (revision 0x400) with 59392K/6144K bytes of memory
.
Processor board ID FCZ140792J5
MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x10
4 FastEthernet interfaces
1 ATM interface
128K bytes of non-volatile configuration memory.
20480K bytes of processor board System flash (Intel Strataflash)
Configuration register is 0x2102
Cisco#
Cisco#
Cisco#
Cisco#end
Translating "end"
% Unknown command or computer name, or unable to find computer address
Cisco#reload
Proceed with reload? [confirm]
*Mar 1 01:19:27.786: %SYS-5-RELOAD: Reload requested by username on console. R
eload Reason: Reload Command.
System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARE
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2006 by cisco Systems, Inc.
C850 series (Board ID: 2-149) platform with 65536 Kbytes of main memory
Booting flash:/c850-advsecurityk9-mz.124-15.T12.bin
Self decompressing the image : ############################################## [O
K]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, R
ELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Fri 22-Jan-10 14:46 by prod_rel_team
Image text-base: 0x8002007C, data-base: 0x814E7240
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
Cisco 857 (MPC8272) processor (revision 0x400) with 59392K/6144K bytes of memory
.
Processor board ID FCZ140792J5
MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x10
4 FastEthernet interfaces
1 ATM interface
128K bytes of non-volatile configuration memory.
20480K bytes of processor board System flash (Intel Strataflash)
no ip dhcp use vrf connected
^
% Invalid input detected at '^' marker.
SETUP: new interface NVI0 placed in "shutdown" state
Press RETURN to get started!
*Mar 1 00:00:03.952: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State change
d to: Initialized
*Mar 1 00:00:03.960: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State change
d to: Enabled
*Mar 1 00:00:07.244: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to
up
*Mar 1 00:00:08.413: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et0, changed state to up
*Mar 1 00:00:08.821: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 01:19:27.072: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state t
o up
*Mar 1 01:19:27.352: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, R
ELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Fri 22-Jan-10 14:46 by prod_rel_team
*Mar 1 01:19:27.352: %SNMP-5-COLDSTART: SNMP agent on host Cisco is undergoing
a cold start
*Mar 1 01:19:27.436: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Mar 1 01:19:27.436: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Mar 1 01:19:27.540: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI0, chan
ged state to down
*Mar 1 01:19:28.072: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Ac
cess1, changed state to up
*Mar 1 01:19:28.484: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, cha
nged state to up
*Mar 1 01:19:28.484: %LINK-5-CHANGED: Interface ATM0, changed state to administ
ratively down
*Mar 1 01:19:28.848: %LINK-5-CHANGED: Interface NVI0, changed state to administ
ratively down
*Mar 1 01:19:28.932: %LINK-3-UPDOWN: Interface FastEthernet3, changed state to
up
*Mar 1 01:19:28.936: %LINK-3-UPDOWN: Interface FastEthernet2, changed state to
up
*Mar 1 01:19:28.940: %LINK-3-UPDOWN: Interface FastEthernet1, changed state to
up
*Mar 1 01:19:29.484: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, chan
ged state to down
*Mar 1 01:19:29.932: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et3, changed state to down
*Mar 1 01:19:29.936: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et2, changed state to down
*Mar 1 01:19:29.940: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et1, changed state to down
*Mar 1 01:19:29.948: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et0, changed state to upAuthorized access only!
===========================================
Please help me as I am stuck and can't go any further....
Hi Dragan,
After you run the wizard Cisco CP Express, it should save the configuration set to update the flash on the router. However, in your case, it seems this is not the case. Therefore:
- Configure the device via Cisco CP Express--> do NOT turn off after that
- Connect to the router with Hyperterminal. Enter the configuration mode by typing:
Enable
When you are prompted for a password to put in. The line should now be router #.now type:
write memoryYou see errors? Otherwise, type:
See the startup-configCheck the output matches the configuration you've tried. If Yes, then you are good to go. If this is not the case, let us know all the errors you received.
-
I'm trying to get a router 871 soho wireless connection to work.
The SDM is useless.
I tried to find documents on how and why and what to do - but no luck.
Since this week. The DSL parts and fw works, but do not
Wireless.
I have a setup of open authentication - comments-mode activated.
So I should be pretty wide open for connections.
I can see the SSID on a client PC, but cannot connect.
I use DHCP clients
--------------------
config below
--------------------
Bridge IRB
!
interface FastEthernet4
Description $$$ FW_OUTSIDE$ $ES_WAN$ ETH - WAN
no ip address
no ip redirection
no ip unreachable
no ip proxy-arp
route IP cache flow
automatic duplex
automatic speed
enable PPPoE
PPPoE-client dial-pool-number 1
No cdp enable
!
interface Dot11Radio0
no ip address
!
SSID 1138
VLAN 1
open authentication
Comments-mode
!
Speed of the basic - 1.0 2.0 - basic basic-5, 5 6.0 9.0 basic-11, 0 12.0 18.0 24.0 36.0
48.0 54.0
root of station-role
No cdp enable
Bridge-Group 1
Bridge-Group 1 covering-disabled people
!
interface Vlan1
Description $ETH - SW - LAUNCH, INTF-INFO-HWIC $$ $4ESW $FW_INSIDE$
IP 192.168.0.109 255.255.255.0
IP access-group 102 to
IP nat inside
IP virtual-reassembly
!
interface Dialer1
Description $FW_OUTSIDE$
MTU 1492
the negotiated IP address
IP access-group 103 to
inspect the DEFAULT100 over IP
NAT outside IP
IP virtual-reassembly
encapsulation ppp
Dialer pool 1
No cdp enable
PPP authentication pap callin
PPP pap sent-username [email protected] / * / password xxx
PPP ipcp dns request accept
!
IP classless
IP route 0.0.0.0 0.0.0.0 Dialer1
!
IP http timeout policy slowed 5 life 86400 request 10000
the IP nat inside source 1 list overload of the Dialer1 interface
!
recording of debug trap
Note access-list 1 INSIDE_IF = BVI1
Remark SDM_ACL category of access list 1 = 2
access-list 1 permit 192.168.0.0 0.0.0.255
Access-list 100 remark generated automatically by the configuration of the firewall Cisco SDM Express
Access-list 100 = 1 SDM_ACL category note
access-list 100 deny ip 255.255.255.255 host everything
access-list 100 deny ip 127.0.0.0 0.255.255.255 everything
access ip-list 100 permit a whole
Access-list 101 remark generated automatically by the configuration of the firewall Cisco SDM Express
Note access-list 101 = 1 SDM_ACL category
access-list 101 deny ip 192.168.0.0 0.0.0.255 any
access-list 101 permit icmp any any echo response
access-list 101 permit icmp any one time exceed
access-list 101 permit everything all unreachable icmp
access-list 101 deny ip 10.0.0.0 0.255.255.255 everything
access-list 101 deny ip 172.16.0.0 0.15.255.255 all
access-list 101 deny ip 192.168.0.0 0.0.255.255 everything
access-list 101 deny ip 127.0.0.0 0.255.255.255 everything
access-list 101 deny ip 255.255.255.255 host everything
access-list 101 deny host ip 0.0.0.0 everything
access-list 101 deny ip any one
access-list 102 remark self-generated by the configuration of the firewall SDM
Note access-list 102 SDM_ACL category = 1
access-list 102 refuse host ip 255.255.255.255 everything
access-list 102 deny ip 127.0.0.0 0.255.255.255 everything
access ip-list 102 permit a whole
access-list 103 note self-generated by the configuration of the firewall SDM
Note access-list 103 SDM_ACL category = 1
access-list 103 deny ip 192.168.0.0 0.0.0.255 any
access-list 103 permit icmp any any echo response
access-list 103 allow icmp all once exceed
access-list 103 allow all unreachable icmp
access-list 103 deny ip 10.0.0.0 0.255.255.255 everything
access-list 103 deny ip 172.16.0.0 0.15.255.255 all
access-list 103 deny ip 192.168.0.0 0.0.255.255 everything
access-list 103 deny ip 127.0.0.0 0.255.255.255 everything
access-list 103 refuse host ip 255.255.255.255 everything
access-list 103 refuse host ip 0.0.0.0 everything
access-list 103 deny ip any any newspaper
Dialer-list 1 ip protocol allow
not run cdp
!
control plan
!
Bridge Protocol ieee 1
1 channel ip bridge
!
max-task-time 5000 Planner
Scheduler allocate 4000 1000
Scheduler interval 500
end
interface Dot11Radio0
no ip address
!
SSID 1138
No vlan 1
!
interface Vlan1
no address ip 192.168.0.109 255.255.255.0
no nat inside ip
Bridge-Group 1
!
interface BVI 1
IP 192.168.0.109 255.255.255.0
IP nat inside
!
end
Cut these commands. I'm going to assume that if you make to a server and not the router DHCP. If you want to use the router, you will need to configure a DHCP pool.
-
Hello
I am looking for assistance in the design of a solution for a customer of our wireless. A basic outline of the network is attached. There are actually many other sites that are shown here, but I just wanted to keep things simple.
The plan is to have a 1240AG access point on each connected remote site the WLC on the WAN. In time, the WCS will be managed by a WCS server.
Each site is already divided into 2 subnets and it is not possible to add a new one for the AP and it's customers. In any case, there will be very few wireless traffic. The AP will run in mode H-HARVEST but there will be no required local communication. All traffic is always aimed at Headquarters (ie they use Citrix). So do these APs actually need to be switch locally H-Reap? If not then how would this work? A remote site AP can function as a H-REAP no?
Some sites have their own 3560 switch and others simply a switch inside a 2801 router module.
There is no need to have any VLANs sent across the WAN.
DHCP is provided by the router at each remote site.
I really need some advice on the best way to implement this solution, including but not limited to:
Do I need to have a separate WLAN for each site?
Will be DHCP from the router actually work?
How should be configured the ports on the switch on the module HWIC?
What benefits are there to having a WCS when there is just a single WLC? (I thought that WCS to manage several WLC).
I skimmed the design guides and I'm still not clear about the best way to do it.
Any help would be appreciated
Thank you
DH
Not in H-REAP... the WLAN SSID that you create on the controller will always be equal to the management interface. This is how the AP and WLC will communicate. When you enable local switching, then you have the ability to map this ssid to a vlan local. I'm currently deploy 90 h PA - harvest with 27 sites and 2 4404 in the heart. I have 7 SSID and using the substitution of wlan. DHCP is local to the remote site and I use the same id of vlan to map the ssid. VLAN local native for the ap is also the same in all, but of couse subnets are different. It's a little different, how you look what interface you need to map the ssid for especially when doing h - harvest.
Look at it this way... only if you have traffic returning to the WLC and the WLC putting back the traffic on the network is when the interface mapping is important... as in a normal installation of LWAPP.
-
WDS on in general and the 2800 series routers
Hello, people!
declares that the WDS is supported on 'some 2800 models', but cisco feature navigator tells me that it is only supported on the access points cisco; I couldn't find any documentation on the WDS configuration on routers also.
Thanks to advice.
The 2800 supports a wireless interface card, in which you can configure for WDS.
HWIC-AP-G-A (=) Cisco 802. 11b / g card to Interface WLAN HWIC-AP for the Americas (the FCC configuration)
HWIC-AP-AG-A (=) Cisco HWIC-AP WIFI 802.11a/b/g map interface to the Americas (the FCC configuration)
Maybe you are looking for
-
Win7 won't start plus-HP Pavilion dv7-6b32us
My HP dv7-6b32us frozen on me this morning. The last two days, it was slow. I used the power button to shut down physically, and when I tried to start it up, I was given the choice: Start the reboot system (recommended) Start Windows normally When
-
Hi all I recently bought a Satego x 200 - 20o, it comes with an integrated Windows Vista Edition Home Premium (Yes, it was in German). In addition, I had Vista Ultimate by my own. The main problem I've encountered is that when I tried to install 'Har
-
Satellite A100-259 (PSAA2E) WIFI problem
Hi, I'm living for a few months in Paris, and I purchased a monthly subscription to a Wi - Fi network I get from the street somewhere (http://www.ozoneparis.net). Everything has been working well for 2-3 weeks, but a few days ago it stopped working.
-
Why the command/tab does not work in the new discourse during a presentation
Why the command/tab doesn't work with Keynote 6.6.1 during a presentation. I can't get out (smoothly and professionally) presentation for applications that run in the background, then return smoothly. Slows down my presentation, seems unprofessiona
-
my printer has stopped printing. The issuance of documents in Quebec and he says the first line is printing, but it is not.