I can't ping or join the local network internal

Similar Questions

• No connection to the local network, cannot connect - Satellite M35-S163

  I think I've tried about 10 different drivers, but I can't ALWAYS connect to the local network.

  He will not get an IP address.

  Other computers have no problem and are connected through the router, but it just won't connect.

  DHCP in router, IP config says the get IP address... No firewall issue... Any new installation of XP SP2

  Any ideas?

  OH, and regarding this... discovered Ethernet controller driver is on one of the Wireless drivers... z

  Hello

  I m bit confused.
  The LAN card is recognized correctly in the Device Manager?
  Check under network adapters and if there is NO yellow exclamation point.

  If the network card is recognized correctly, then you should check the LAN parameters-> * Protocol of TCP/IP.

  IP address, getway must be set to assign automatically.

  Check it!

• I can connect to the local network, but not to the internet

  Why in an internet connection, I can connect to the Local network, but not to the Internet.
  I have valid IP address and configuration is good.

  I recommend you read some threads here in the forum about similar issues.
  If this problem occurs using the WiFi network, then check if you can use the connection to the local network.
  Using the WiFi network, you must check if the common WLan parameters are favourable;
  Check if the encryption key is right; turn off filtering by mac address, check the TCP/IP protocol settings if it has been set to automatic, disable the firewall settings, rest you WLan router, check if you connected to the right SSID.

  Good bye

• I am refurbishing a Pavillion m7560n and I can't find a driver for the local network. Can you help me? CC = en

  I am refurbishing a Pavillion m7560n and I can't find a driver for the local network. Can you help me?

  Here is the link to the LAN of your system drivers:

  http://ftp.HP.com/pub/softlib/Software7/COL15134/ob-40490-1/sp26744.exe

• How can I disconnect from the internet but to maintain my connection to the local network in Windows 7?

  I need to disconnect internet to my PC Windows 7 while maintaining my LAN network. Can anyone help?

  Hello

  If you want to disconnect Internet on the Windows 7 computer, then you can follow the steps mentioned below. These steps would help you to disconnect from the wired connection, while the connection is still active.

  (a) click Start.

  (b) type network and sharing Center in the start search bar and press ENTER.

  (c) in the left pane, click on change adapter settings

  (d) it would be to open a window with the connection to the wired LAN.

  (e) now, right click on the wired LAN connection icon and select Disable. (Provide the password if necessary).

  (f) it would disconnect the computer from Windows 7 to connect to the local network.

• Connected to the local network, but can not use internet

  I recently had problems with access to the internet after reinstalling windows 7. Before the reinstall worked very well.

  I can connect to the local network without problem, and it shows that the internet is connected. Yet I can not access the internet. When I disconnect and reconnect, I get a few seconds of internet work before it stops working.

  When a diagnosis in the network and sharing Center, I get the error "default gateway is not available" and occasionally "the connection between your access point, etc. and internet is broken"

  Other computers and devices using the network are working properly, although there was a 'competitor IP address' error on another pc, which, after a reconnection, solved itself.

  I use an edimax 802.11n wireless card and a D-link router

  I tried several things to make it work again, but without result. Any help would be greatly appreciated

  disable TCP/IPv6 had no effect.

  I think I can have fixed me, I installed the driver microsoft before the reinstall instead of the driver edimax and internet suddenly started working.

  Thanks for the help of yor

• ASA5505 can transfer clients to remote VPN access to the local network

  I have currently ASA 5505 and 2911-router and I am trying to configure the VPN topology.

  Can ASA5505 you transmit to remote VPN access clients LAN operated by another router?

  These two cases are possible? :

  (1) ASA 5505 and 2911-router are separate WAN interfaces, each connected directly to the ISP. But so can I connect an other interfaces LAN of ASA 5505 in a switch managed by 2911 router customers to distance-SSL-VPN to inject into the local network managed by the router?
  (2) ASA 5505 is behind router-2911. May 2911 router address public ip or public ip address VPN-access attempts have directly be sent to ASA 5505 when there is only a single public ip address address available?
  Long put short, ASA 5505 can inject its clients to remote-access-VPN as one of the hosts on the local network managed by 2911-router?
  Thank you.

  I could help you more if you can explain the purpose of this configuration and connectivity between the router and ASA.

  You can activate the reverse route on the dynamic plane on the SAA. The ASA will install a static route to the customer on the routing table. You can use a routing protocol to redistribute static routes to your switch on the side of LAN of the SAA.

• WIN 7 does not have the net driver for Asus A2D WHAT CAN I DO. I HAVE THE CONNECTION TO THE LOCAL NETWORK.

  WIN 7 does not have the net driver for Asus A2D. or I'm unable to find it.
  WHAT I CAN DO. I HAVE THE CONNECTION TO THE LOCAL NETWORK.
  Thanks for any idea, address etc.
  DragMil
  You can wito to * address email is removed from the privacy *.

  Try an older driver installed in compatibility mode

  To run in compatibility mode do the following:

  Click with the right button on the installer > properties > compatibility > choose OS

  http://Windows.Microsoft.com/en-us/Windows-Vista/make-older-programs-run-in-this-version-of-Windows?SignedIn=1

• How can I save my documents of clouds on the local Adobe DC file? I can read my documents on the cloud, but I can't play them on the local file... Thank you

  How can I save my documents of clouds on the local DC Adobe file on iPad?

  I can read my documents on the cloud, but I can't play them on the local file...

  Thank you

  This is a help your device-related topic: Adobe Acrobat help for iOS: managing files and folders

  Saving files locally

  To save the files locally on your device:

  • Use iTunes to synchronize the file to your device.
  • Send an email with a PDF attachment to yourself and open it with Acrobat Reader.
  • Download the file to your device via a 3rd party like Dropbox service.

• ASA 5505 IPSEC VPN connected but cannot access the local network

  ASA: 8.2.5

  ASDM: 6.4.5

  LAN: 10.1.0.0/22

  Pool VPN: 172.16.10.0/24

  Hi, we purcahsed a new ASA 5505 and try to configure IPSEC VPN via ASDM; I simply run the wizards, installation vpnpool, split tunnelling, etc.

  I can connect to the ASA using the cisco VPN client and internet works fine on the local PC, but it can not access the local network (can not impossible. ping remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile, I created worked very well.

  Here is my setup, wrong set up anything?

  ASA Version 8.2 (5)

  !

  hostname asatest

  domain XXX.com

  activate 8Fw1QFqthX2n4uD3 encrypted password

  g9NiG6oUPjkYrHNt encrypted passwd

  names of

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 10.1.1.253 255.255.252.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  address IP XXX.XXX.XXX.XXX 255.255.255.240

  !

  passive FTP mode

  clock timezone PST - 8

  clock summer-time recurring PDT

  DNS server-group DefaultDNS

  domain vff.com

  vpntest_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.252.0

  access extensive list ip 10.1.0.0 inside_nat0_outbound allow 255.255.252.0 172.16.10.0 255.255.255.0

  pager lines 24

  Enable logging

  timestamp of the record

  logging trap warnings

  asdm of logging of information

  logging - the id of the device hostname

  host of logging inside the 10.1.1.230

  Within 1500 MTU

  Outside 1500 MTU

  IP local pool 172.16.10.1 - 172.16.10.254 mask 255.255.255.0 vpnpool

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  AAA-server protocol nt AD

  AAA-server host 10.1.1.108 AD (inside)

  NT-auth-domain controller 10.1.1.108

  Enable http server

  http 10.1.0.0 255.255.252.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH 10.1.0.0 255.255.252.0 inside

  SSH timeout 20

  Console timeout 0

  dhcpd outside auto_config

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal group vpntest strategy

  Group vpntest policy attributes

  value of 10.1.1.108 WINS server

  Server DNS 10.1.1.108 value

  Protocol-tunnel-VPN IPSec l2tp ipsec

  disable the password-storage

  disable the IP-comp

  Re-xauth disable

  disable the PFS

  IPSec-udp disable

  IPSec-udp-port 10000

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list vpntest_splitTunnelAcl

  value by default-domain XXX.com

  disable the split-tunnel-all dns

  Dungeon-client-config backup servers

  the address value vpnpool pools

  admin WeiepwREwT66BhE9 encrypted privilege 15 password username

  username user5 encrypted password privilege 5 yIWniWfceAUz1sUb

  the encrypted password privilege 3 umNHhJnO7McrLxNQ util_3 username

  tunnel-group vpntest type remote access

  tunnel-group vpntest General attributes

  address vpnpool pool

  authentication-server-group AD

  authentication-server-group (inside) AD

  Group Policy - by default-vpntest

  band-Kingdom

  vpntest group tunnel ipsec-attributes

  pre-shared-key BEKey123456

  NOCHECK Peer-id-validate

  !

  !

  privilege level 3 mode exec cmd command perfmon

  privilege level 3 mode exec cmd ping command

  mode privileged exec command cmd level 3

  logging of the privilege level 3 mode exec cmd commands

  privilege level 3 exec command failover mode cmd

  privilege level 3 mode exec command packet cmd - draw

  privilege show import at the level 5 exec mode command

  privilege level 5 see fashion exec running-config command

  order of privilege show level 3 exec mode reload

  privilege level 3 exec mode control fashion show

  privilege see the level 3 exec firewall command mode

  privilege see the level 3 exec mode command ASP.

  processor mode privileged exec command to see the level 3

  privilege command shell see the level 3 exec mode

  privilege show level 3 exec command clock mode

  privilege exec mode level 3 dns-hosts command show

  privilege see the level 3 exec command access-list mode

  logging of orders privilege see the level 3 exec mode

  privilege, level 3 see the exec command mode vlan

  privilege show level 3 exec command ip mode

  privilege, level 3 see fashion exec command ipv6

  privilege, level 3 see the exec command failover mode

  privilege, level 3 see fashion exec command asdm

  exec mode privilege see the level 3 command arp

  command routing privilege see the level 3 exec mode

  privilege, level 3 see fashion exec command ospf

  privilege, level 3 see the exec command in aaa-server mode

  AAA mode privileged exec command to see the level 3

  privilege, level 3 see fashion exec command eigrp

  privilege see the level 3 exec mode command crypto

  privilege, level 3 see fashion exec command vpn-sessiondb

  privilege level 3 exec mode command ssh show

  privilege, level 3 see fashion exec command dhcpd

  privilege, level 3 see the vpnclient command exec mode

  privilege, level 3 see fashion exec command vpn

  privilege level see the 3 blocks from exec mode command

  privilege, level 3 see fashion exec command wccp

  privilege see the level 3 exec command mode dynamic filters

  privilege, level 3 see the exec command in webvpn mode

  privilege control module see the level 3 exec mode

  privilege, level 3 see fashion exec command uauth

  privilege see the level 3 exec command compression mode

  level 3 for the show privilege mode configure the command interface

  level 3 for the show privilege mode set clock command

  level 3 for the show privilege mode configure the access-list command

  level 3 for the show privilege mode set up the registration of the order

  level 3 for the show privilege mode configure ip command

  level 3 for the show privilege mode configure command failover

  level 5 mode see the privilege set up command asdm

  level 3 for the show privilege mode configure arp command

  level 3 for the show privilege mode configure the command routing

  level 3 for the show privilege mode configure aaa-order server

  level mode 3 privilege see the command configure aaa

  level 3 for the show privilege mode configure command crypto

  level 3 for the show privilege mode configure ssh command

  level 3 for the show privilege mode configure command dhcpd

  level 5 mode see the privilege set privilege to command

  privilege level clear 3 mode exec command dns host

  logging of the privilege clear level 3 exec mode commands

  clear level 3 arp command mode privileged exec

  AAA-server of privilege clear level 3 exec mode command

  privilege clear level 3 exec mode command crypto

  privilege clear level 3 exec command mode dynamic filters

  level 3 for the privilege cmd mode configure command failover

  clear level 3 privilege mode set the logging of command

  privilege mode clear level 3 Configure arp command

  clear level 3 privilege mode configure command crypto

  clear level 3 privilege mode configure aaa-order server

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4

  : end

  Captures we can see packets going from the pool to the internal LAN, but we do not reply back packages.

  The routing must be such that for 172.16.10.0/24 packages should reach the inside interface of the ASA.

  On client machines or your internal LAN switch, you need to add route for 172.16.10.0/24 pointing to the inside interface of the ASA.

• Ipad Cisco ipsec VPN connects but not access to the local network

  Hi guys,.

  I am trying to connect our ipads to vpn to access network resources. IPSec cisco ipad connects but not lan access and cannot ping anything not even not the interfaces of the router.

  If I configure the vpn from cisco on a laptop, it works perfectly, I can ping all and can access resources on the local network if my guess is that the traffic is not going in the tunnel vpn between ipad and desktop.

  Cisco 877.

  My config is attached.

  Any ideas?

  Thank you

  Build-in iPad-client is not useful to your configuration.

  You have three options:

  (1) remove the ACL of your vpn group. Without split tunneling client will work.

  2) migrate legacy config crypto-map style. Here, you can use split tunneling

  3) migrate AnyConnect.

  The root of the problem is that the iPad Gets the split tunneling-information. But instead of control with routing traffic should pass through the window / the tunnel and which traffic is allowed without the VPN of the iPad tries to build a set of SAs for each line in your split-tunnel-ACL. But with the model-virtual, SA only is allowed.

• Computers on the local network does not show up after the installation of macOS Sierra

  Shared on my LAN Macs make their appearance is more after the installation of macOS Sierra. See the attached servers is checked in the preferences of the Finder and the computers appear in the list of DHCP clients on the router. I can see these computers to each other. Sharing is disabled on the computer of the Sierra. Any ideas?

  Thank you!

  p.s. I can not even 'go' to the IP address of these computers.

  Correction: I can afp: / and vnc: / to IP addresses (and so far as a temporary solution, I assigned permanent IP addresses in the router on all computers on the local network). Once I afp: on a local computer, it appears on the side bar of the Finder under shared devices, well I saw several times it appears and then disappears. Nothing has changed on the network since the installation of Sierra.

• Re: Satellite Pro A40 - connection to the local network

  Hello

  My names Andy and not bieng a total beginner computer, I tried to install all the drivers for my laptop model a SPA40 old fathers PSA45E-001VM-EN. (European model I think) everything looks ok, except that I can't get the ETHERNET driver.

  When I go into the Device Manager there is NO controller network displayed in the list and there is a yellow exclamation mark against two controllers ethernet ib the OTHER DEVICES tab looking here, I downloaded the atheros wlan xp file - 7704062.zip, broadcom wlan xp - installed 5604835.ziplan20070912134727.zip and nothing changes, we used to be able to go on the net and with the wifi card in the pci slot wireless go so I know its capable I think it's just the order of drivers and the drivers themselves,

  Then someone can point me in the right direction before as I have send myself crazy with this...

  You can

  regards and thanks in advance

  Andy

  Hey,.

  The drivers that you downloaded are WLAN Card and has nothing to do with the connection to the local network (Ethernet) normal

  I think you should check the Web from Toshiba site to download the latest LAN driver. You can find the drivers for Satellite Pro A40 in * archives *.
  ttp://EU.computers.Toshiba-Europe.com/innovation/download_drivers_bios.jsp h

• Satellite A105-4114 will not recognize the connection to the local network

  Whenever I plug my cable ethernet to ethernet port on my laptop, the ethernet port does not recognize my cable, even if the lights are flashing. I updated my LAN driver a week ago, and it has not really helped. My internet service is provided by my apartment complex at the school, but I don't think it has anything to do with it, because I had this problem last year living in dorms and at home. I have to restart my computer everytime for my computer to recognize the connection to the local network. Can someone help me please?

  Driver: Intel (r) PRO/1000 PL Network Connection

  Wireless connection works fune.

  Hello

  First of all, you should check your LAN cable.
  Sometimes the laptop may not be correctly connected to the LAN as a result of a defective cable.
  In addition, you should check if the network card is properly recognized in Device Manager. He should t be a yellow exclamation!
  In addition, you must check the settings for the TCP/IP protocol in the LAN card properties.
  TCP/IP must be set to automatic. I assume that you are connected to a server and the server supports supported a range of IP addresses and assigns it automatically.

  Last but not least check if you are using the latest version of the BIOS.

  Welcome them

• HP OfficeJet Pro 8600: HP OfficeJet Pro 8600, connected to the local network but does not print a printer on the same LAN

  HP OfficeJet Pro 8600, connected to the local network but cannot print printer on the same local network.

  Work tried fixing it but all attempts fail.

  Firewall disabled.

  Printer recognizes the router's LAN.

  Was also pointed out that the port does not communicate, can not remove it; Cannot add another...

  Printer does not print.

  How can I fix?

  Hi @AnnisMonadjem,

  Welcome to the Forums of HP Support!

  I understand that you are unable to print to your printer HP Officejet Pro 8600. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  When you say 'LAN', are you referring to the network or you try to share the printer on the network?

  How is the printer connected? (Ethernet/WiFi)

  If you have noticed that the port is causing problems, please download and run the print and Scan doctor, it will be probably diagnose and fix the problem you are experiencing.

  What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)

  HP has several Officejet Pro 8600 series.

  What is the name and the product number of your printer? How can I find my model number or product number?

  • Update the firmware of the printer.
  • Don't hide the SSID (network name).
  • What type of encryption are you helping? HP recommends WPA and WPA2.
  • You have a double router broadband? Make sure that the two groups were not the same network name.

  If the problem persists, you may encounter an IP address conflict. It's a good idea to assign the printer a static IP address outside your DHCP range. For example, some routers default DHCP is located between 192.168.0.100 to 192.168.0.200. So, I would use 192.168.0.232.

  To assign the static IP address, use the following steps as a guide.

  • Print a Page of Network Configuration menu of the printer front panel. Note the IP printer. IPV4 address
  • Type the IP address in the browser to bring up the SAP.
  • Choose the network tab, then wireless on the left side, and then select the IPv4 tab.
  • Select Manual IP.
  • Enter your IP address manual (192.168.0.232)
  • Enter 255.255.255.0 for the subnet mask, except if it is different.
  • Enter the IP address of your router that sits on the Network Configuration Page) for the default gateway.
  • Please, click on manual DNS server. For the preferred DNS Server Manual please enter 8.8.8.8 and the Alternate DNS Server Manual, please enter 8.8.4.4.
  • Click on apply.
  • Restart the router, the printer and the computer.
  • Test printing and scanning.

  If the problem persists, download and run this patch rollup: resolving printing issues in Windows 7 and Windows Server 2008 R2

  • Try printing and scanning.

  In addition, if you are still having problems try the steps in this guide, HP printers - "offline" Status Message printer (Windows 7).

  Continue on, if the problem persists.

  Important!   Delete the temporary files and folders by using the disk cleanup utility

  1. Open the disk cleanup utility: