I have a home wireless network that is not safe. Need step by step instructions on how to secure.

Similar Questions

• I have a Buffalo wireless card that will not get a wireless connection. "No wireless network in range.

  original title: NIC Buffalo

  I have wireless G 54 Mbps Buffalo Airstation net card and cannot get a wireless connection. I've already tried uninstalling the software/drivers, reinstall the software/drivers.  I tried to enter the IP address manually, but I get the same message.  "No wireless network in range.  I can use the adapter wireless interal very well, but want to use the faster card.  Someone at - it ideas?  The router is a D-Link, and is not mine, so I can't do it around with her money.

  Thanks in advance,

  Sharon

  Hello Sharon,
   
  Follow the methods given in the order.
   
  Method 1: Restart the Wireless Auto-Configuration service

  To restart the service automatic wireless setup follow the steps below.

  i. Click Start
  II. click on run
  III. run window, type the command services.msc and click OK
  IV. on the list of services, select Wireless Auto Configuration.

  v. Double click on the service
  VI. click on stop and then click Start
  VII. click on apply, then OK.
   
  Restart the computer and check.
   
  Method 2: Try the steps listed in the following article and check, if it helps in fixing the issue:
   
  How to troubleshoot wireless network connections in Windows XP Service Pack 2

• Home wireless network communication problems

  I can't connect with my other computer on my home wireless network. I don't see the other computer files, on my computer, I could before. I could see them before and I could save the files/folders from one computer to another, but suddnely stopped this from happening.

  I have Windows XP Home Edition

  Hello

  Maybe this can help.

  Make sure that the software firewall on each computer allows free local traffic. If you use 3rd party Firewall on, Vista/XP Firewall Native should be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructions

  General example, http://www.ezlan.net/faq#trusted

  Please note that some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  Windows XP file sharing - http://support.microsoft.com/default.aspx?scid=kb;en-us;304040
  Sharing printer XP - http://www.microsoft.com/windowsxp/using/networking/expert/honeycutt_july2.mspx

  Setting Windows native firewall for sharing XP -http://support.microsoft.com/kb/875357

  In Win XP pro you can visually see the setting of authorization/security and configure them according to your preferences.

  http://www.Microsoft.com/windowsxp/using/security/learnmore/AccessControl.mspx#securityTab

  When you have finished the configuration of the system, it is recommended to restart everything the router and all computers involved.

  
  

• Recently installed vista update. I can no longer connect to my home wireless network.

  Recently installed vista update.  I can no longer connect to my home wireless network.  I get a message that says 'wireless link failed because windows did not receive response from the access point or wireless router.  I troubleshott he said of computing could be from low signal strength and yet it shows the strength of 100%.  Anyone have any ideas?

  Hello

  Check the firewall it is maybe it has been reset.

  In general.

  Most laptops have a physical switch for the wireless card. Read the manual of the computer and make sure that the wireless adapter is on.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  Make sure that if there is Wireless Utility a utility vendor is not running with the native Windows wireless utility.

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Above everything is OK and it connects to the wireless router. Log in from any computer which is, or can be connected to the router with a wire wireless, disable wireless security, make sure that the wireless streaming is enabled and try to connect with no. wireless security.

  When the work turns on the Wireless security.

  Note * people sometimes make mistakes in writing and retype the password for security.

  Another way is to copy in the menu of the router and then paste it when asked of the wireless card.

  --------------------------------------------------

  I really checked and configured every thing and it doesn't work.

  Software firewall application that is not configured to allow local traffic (between the computer and the router is also a possible problem.
  some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  
  

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• "You have no preferred wireless networks.

  Hello

  I installed Build 7100 and have been finding problems in all directions. Is it the right place to report issues? The dev team will never receive any comments posted here?

  I have a specific problem that is driving me crazy and if it is not sorted there is no way I will buy Windows 7 when it is released. Whenever I reboot or exit the mode 'sleep' my wireless network was disconnected. The problem is that it automatically reconnect. In fact when I try a reconnection he asks me the password all over again as if she had never met before network. In addition, I have try three or four times before it connects without error. The network is also extremely stable and was under XP.

  The Troubleshoot utility of reports "You have no preferred wireless networks", which is false, because I connect automatically is always checked for this SSID. I tried which allows to 'Connect even if the network is not broadcasting its name (SSID)', but this option is reset after reboot / sleep. "Connect automatically" is still however verified. Installed with the driver is REALTEK USB Wireless LAN Utility Version 402.1470.518.2007.

  I fear that such problems will not get noticed at Microsoft because they are now focusing only on telemetry. I want to buy Windows this time, I don't really, but I won't buy a defective product.

  I connect to the Router 1 billion (BiPAC 7401VGP R3) with a USB (BiPAC 3012 G) wireless network adapter.

  Hi Vargorlopano,

  Thanks for posting on the Forum of answers.

  Some network cards have to be able to save the settings that will put your NIC sleep when Windows goes to sleep.

  You can click Start, type "power options" then right click on the entry that is displayed at the top of the menu and click on "Run as Administrator".
  Your password can be asked to you.
  On the right side of the window, click on "Change plan settings", then click on "change power avancΘs."
  You should see an entry in the list that says 'wireless adapter settings', change it to 'Performance', and click OK.
  Click on save changes.

  Please let us know if that helps.

  Chris
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• When I try to connect to my wireless network, that it asks a security key how do I find the key my router is a comtrend CT-5363

  When I try to connect to my wireless network, that it asks a security key how do I find the key my router is a comtrend CT-5363

  Hello

  1. what operating system do you use?

  2 did you change on your computer?

  3. who is your internet service provider?

  If you use windows7, I suggest you to follow the steps from the links and check out.

  Set up a wireless router

  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-wireless-router

  Network connection problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  Set up a security key for a wireless network

  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-security-key-for-a-wireless-network

• Currently have XP Home Edition 2002 Pack 3 and upgrade to the latest version free. How do I do that?

  Upgrade XP 2002 to more current system

  Currently have XP Home Edition 2002 Pack 3 and upgrade to the latest version free. How do I do that?

  Currently have XP Home Edition 2002 Pack 3 and upgrade to the latest version free. How do I do that?

  Last free version of what?

  If you're talking about Windows, it has never been free.

• I have a Windows XP on the network that does not allow administrative tasks

  I have a Windows XP computer that does not allow certain administrative tasks. I can't access retore system with the domain administrator. I don't want uninstalll and reinstall Windows because I also installed Office and who have to copy. I ran a spyware and have cleaned the questions. Try a second spy software.

  Thank you

  Terry

  Like I said, it could be any file requiring a restore of the system to access what has been its permissions modified by malware.  If I was at that time, I would declare my compromised machine and reinstall Windows completely.  If you are determined not to reinstall, you can use a tool such as Microsoft "Process Monitor" that will display all the queue access that occur when you run the program.  You may be able to locate the file that is being denied access, but you're going to be turning to sift through a large amount of data.

  Good luck and hope this helps.
  JW

  Process Monitor: http://technet.microsoft.com/en-us/sysinternals/bb896645>

• I'm trying to our laptop connecton to our home wireless network

  I tried to connect one of our PCs to our wireless network and continue to get the dialog box Windows network box indicating "wireless authentication failed because of a time-out" this pc had a virus on it, but has been deleted, clean and renovated.  It was plugged in and worked before why not now? He does not see the wireless network but will not connect help?

  Hello

  I suggest you to follow the steps in this link and check if it helps:

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  It will be useful.

• Wireless network adapter could not be activated

  My laptop also did EXACTLY the same thing in the morning today.
  No effect with the wireless on switch on the computer. The light is always red. Last night an automatic update that happened (update for windows Vista (KB955430) 09/05/2009 09:03), which cannot be deleted. I don't know if this problem is related with the update.

  My laptop is HP Pavilion dv6439nr.  Running Windows Vista Home Premium (Service Pack 1).  Wireless adapter is "broadcom wireless 802.11 b/g WLAN PCI" that is gone now.

  Windows network diagnostics shows "this computer doesn't have a card installed and configured wireless network."

  HP Home Network Center shows "Wireless status: disabled; When I try to enable wireless LAN, it shows "wireless network adapter could not be activated.

  I tried to scan and reinstall the driver but the device does not appear.

  The wireless router works fine with other laptops.

  If anyone has a solution it would be greatly appreciated.

  Thank you

  Alboury,
  It seems at this point that your wireless network adapter has a hardware problem.  Check out this troubleshooting guide step by step on the HP Pavilion support web site.  If you can't get your active wireless card, you will need to contact HP or repair HP authorized repair for hardware Center.

  http://h10025.www1.HP.com/ewfrf/wc/document?DocName=c00813382&LC=en&DLC=&cc=us&product=3619365&rule=5493&lang=#WLANStatus

  Let us know if we can provide assistance.

  Thank you
  Gloria
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Wireless network adapter is not installed and configured

  I have recently re installed windows vista for my laptop dell inspiron 1545. I am not able to connect to wireless internet, it says that the wireless network adapter is not installed and configured. How do I install it and where can I get the wireless network adapter. I have a cd or anything for it. Thank you

  You can get in trouble with your device drivers, firmware and/or software.  Go to the Device Manager by going to start / find and type Device Manager and enter and then double-click on the program icon that appears.  Check each device to a red x, yellow! or white?  These identify devices with problems probably (drivers, but also of conflict or something else).  Click on each for more details and troubleshooting tips.  If you need to get drivers (and you shouldget from Dell for the wireless adapter at all you have time to do - they can help way beyond simply solve this problem), let the computer dealer or the manufacturer of the device (NOT of Microsoft Updates).  In fact, you must disable automatic updates in Windows Update driver as follows:http://www.addictivetips.com/windows-tips/how-to-disable-automatic-driver-installation-in-windows-vista/. Follow these steps to get the drivers: http://pcsupport.about.com/od/driverssupport/ht/driverdlmfgr.htm.  Once you have the drivers, you can install them via the Manager device as follows:http://www.vistax64.com/tutorials/193584-device-manager-install-driver.html. > http://support.microsoft.com/kb/244617.

  The adapter is inside the laptop.  You don't need to do something with it to install it.  Install the drivers, firmware or software for it and your version of Vista from Dell (all that apply) "install".  You must then go to start / Control Panel / Network and sharing Center and configure the adapter with the appropriate parameters and to establish the appropriate network connections.  This will take place in settings required by your ISP, and maybe your router or modem (so you may need to contact them if you don't know the settings).

  Here are the procedures for Vista with Windows7 network layout that can help:http://www.windowsnetworking.com/articles_tutorials/Windows-7-Understanding-Network-Administration-Configuration.html.

  Here is another article on home networks (with several links to related articles which must all be considered - as well as others, you will find in the related articles) to help you better understand the home networks: http://windows.microsoft.com/en-US/windows-vista/Setting-up-a-home-network.  If it's for Vista, much of it applies to Windows7 (although there may be some differences that should be addressed in the previous article).

  Here is an article on the networking of the different versions of Windows:http://windows.microsoft.com/en-us/windows7/Networking-home-computers-running-different-versions-of-Windows.

  Here is a tutorial on how to set up a home network (including a wireless)-click on additional links for more information that may be helpful:http://windows.microsoft.com/en-US/windows-vista/Setting-up-a-home-network.

  Here is an article on troubleshooting network connections wireless (with links):http://windows.microsoft.com/en-US/windows-vista/Troubleshoot-network-connection-problems.

  Here's a long guide on wireless internet connections in Vista:http://www.techwarelabs.com/guides/misc_mod/vistaconnection/.

  Here is an article on how to set up wireless internet in Vista:http://www.clpgh.org/usingthelibrary/technology/wireless/WindowsVista.pdf.

  As I am unsure of your Setup, I've included several items that can help depending on how you are setup.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Receive the message error "wireless network connection is not a valid ip configuration.

  Original title: unable to connect to wifi on windows 7 on Dell laptop

  Help!  I went on vacation and used my laptop to DVD play only.  I am now back home and cannot connect to the Internet.  I tried all sorts of resolutions without result.  When I use the Troubleshoot utility, it tells me to stop my router and turn it back on.  I've done this multilpe times at this point.  Once I keep in the resolution of the problems, I get the same message again and again: "wireless network connection is not a valid ip configuration.  I disabled McAfee and morning services.  I used the command prompt to reset WINSOCK, IPv4 and 6.  I turned power on and off wireless by using the key on the keyboard.  I disabled and enabled the network connection.  I have the driver-upated.  I know the router works properly from my iphone and iPad is all connected without problem.  I removed and added to the wireless network.  In the network and sharing Center (I would copy and paste the view up here, if I could, but since I can't get online...), it is said "unidentified network, no internet access" on the right side, and he also says that I'm connected to a public network.  There is no link to click for the public network and I can't seem to find a way to change it to the House (there are no options, no links).  I tried to solve this problem, after I get home from work every night and I'm so frustrated that nothing works.  Please, please help!

  Kristine,

  Please try these steps before replacing the adapters and let us know the results.

  1. To open a command prompt, click Start , and then type CMD in the programs and files.
  2. Right click on CMD.exe in the programs icon and select run as administrator.
  3. When the user account control pop up box, click Yes.
  4. At the command prompt, copy and paste (or type) the following command and then press ENTER:
     netsh int ip reset c:\resetlog.txt

     Note If you do not specify a path of the directory for the log file, use the following command:

     netsh int ip reset resetlog.txt
  5. Restart the computer.

  If the problem persists, go through the given suggestion't-have-valid-ip/62ca59b1-c173-4465-9153-554a13928315 http://answers.microsoft.com/en-us/windows/forum/windows_7-networking/wireless-network-connection-doesn

  Hope that these measures could help you.

• Wireless network adapter does not work on my Satellite A200

  Hello

  My wireless network adapter does not work under Vista. If I press FN + F8 nothing happens. Wireless communication is always offline.

  What can I do?

  Details:
  Typ: Atheros AR5008X Version: 7.2.0.164
  Laptop Satellite 200
  PSAE6E

  Please help me!
  Thanks in advance!

  Phil

  BIOS bug? I don t think so

  First of all, you must make sure that this isn't a hardware problem. In this case, insert the Toshiba Recovery CD and reinstall the operating system of this device. This will outline the laptop to factory settings. Notes; This would format the whole HARD drive.

  After the new installation, you must activate the WLan switch on the side of books, and you can then use the switch button FN + F8 to select the WiFi network.

  I assume that you have already configured your Wlan router. So the same settings such as the SSID, encryption of WLan, etc. must be defined on the laptop too.

• The feature you are trying to use is on a network that is not available. Click OK to try again or enter a different path to the folder that contains the installation packagr 'TrayApp.msi'

  Original title: trayapp

  When I open the computer message appears, the component you are trying to use is on a network that is not available. Click OK to try again or enter a different path to the folder that contains the installation packagr 'TrayApp.msi' in the box below.
  C:\Users\user\AppData\Local\Temp\7zS5216\setup\TrayApp\
  When I click ok the message this way that c:\users\user\appdata\local\temp\7zs5216\setup\trayapp\ is not found. Verfy that you have access to this location and try again or try to find the 'TrayApp.msi' in installing a package file from which you can install the product'TrayApp.
  When I try to cancel the warning message, is that an installation package for the TrayApp product is not found. Again the installation again using a valid copy of the 'TrayApp of installation' package. I already uninstalled all HP products, but this message is still bothering me, how to solve this problem?

  Hey Tama,

  
  -What version of windows is installed on the computer?
  -Have there been recent changes to the computer before the show?
  I recommend you go through the next HP document and check if it helps.
  http://h10025.www1.HP.com/ewfrf/wc/document?LC=en&DLC=en&cc=us&DocName=c00811375
  Hope this information is useful.

• Update my wireless network device does not work after installation of Software Distribution Service 3.0

  After the installation of Software Distribution Service 3.0 update my wireless network camera does not work how do I uninstall Software Distribution Service 3.0

  How did you receive the update?

  Was it via Windows Update or Microsoft Update?

  Before the changes are made to your computer, the system restore points are made. This is so that you can go back in case an update causes problems.

  Follow these steps:

  1. click on the Start button

  2. click on accessories

  3. click on system tools

  4. click on system restore

  5. click on next

  6. in the calendar that appears, select the one which refers to Software Distribution Service 3.0 and click Next

  After the collection of certain data, the computer will restart, and the update will be gone.

  Hope this helps

  Post back if necessary

  ___________________________________________________________

  If this post can help solve your problem, please click the 'bookmark' or 'Yes' to this message button. Marking a post as answer, or relatively useful, you help others find the answer more quickly.