I'm on disk check utility, how do I know when its done and how I know whether or not, I have a problem?

Similar Questions

• 'the disk check utility requires exclusive access to Windows__files on disk' (my hard drive). "Re-start of Windows. __

  FAILED: attempt recovery of bad sectors (disk hard C)

  I followed the instructions to increase the speed of the PC on the home screen of the box to highlight the function of microsoft.com.

  I could access the program successfully on my home screen (Windows XP Edition family version 5.1 service pack 3.0).  Phase 1 of the scan completed successfully, but about 70% through the phase 2, the analysis stopped and I got this message: "the disk check utility requires exclusive access to some Windows files on the disk.  These are accessible only by re-starting Windows. "   I was in charge of restarting my computer and repeat the test.  I did this, but got the same message several times in a row.

  I use the MS Update center regularly, my Windows XP software has been certified 3 times as being Windows genuine, and I update MS Security Essentials at least every 2 days.  I DON'T KNOW WHAT ELSE TO TRY!  As a general rule, ALL my other Windows functions work correctly & completely of my home screen.

  I also welcome Microsoft to have remote access to my computer, so that they can analyze & fix problems as well hardware & software automatically or from the center of MS Fix - IT.

  Please contact me at * address email is removed from the privacy * with specific instructions.  I'll try the center of update every day, where you will find all items that can be downloaded to fix this thank you for your continued support.  Joy Knobloch

  UPDATE WE CHECK DISK: 2 responses of PML & TWELCH were marked as possible answers.  After you schedule a check disk and shut down your computer, you must WAIT an hour or two before starting.  There is perhaps a long line of users waiting to get their audited records!  I finally managed to get the disk to run check (I also checked the box that says automatically correct errors).  BUT I NEVER GOT A CONFIRMATION MESSAGE THAT DIRECTLY STATED THAT ANY "BAD SECTORS" HAD BEEN RE-COVERED.

  LAST QUESTION: Can we assume that if the disk check ran completely and automatically corrected "problems", that the "DEFECTIVE SECTORS" have been found?

  Thanks to everyone who participated in this forum.  E-mail address is removed from the privacy *.

  It is not clear what you were / are doing.  Try this:

  Start > run > chkdsk /f > OK

  A box appears with the following message:

  The type of the file system is NTFS.
  Cannot lock the current drive.

  Chkdsk cannot run because the volume is in use by
  process.  You want to schedule this volume t
  check the next time the system restarts? (Y/N)

  Type Y and press ENTER.  Then, restart the computer.

  If, during the process that follows, you still receive the message "FAILED: attempt recovery of bad sectors (disk hard C)" or something similar, go to the website of the manufacturer of your drive hard drive and download the appropriate for your hard drive diagnostic tool.

  I also welcome Microsoft to have remote access to my computer, so that they can analyze & fix problems as well hardware & software automatically or from the center of MS Fix - IT.

  Unless you allowed to access remotely in accordance with a phone call to the support of MicrosoftTHAT YOU HAVE MOMENTUM, you must disable the remote access and Remote Desktop (right click on post work, select Properties, click on the 'Remote' tab).  In fact, you must disable these features now and only reactivate if still initiate you a phone call to technical support Microsoft and will need to enable them.

• Envy touch: how to determine whether or not Windows 10 is an upgrade on an HP laptop?

  I need help on how to determine if the 10 Windows on the laptop is an upgrade to say Windows 8 or is not an upgrade.

  I had some problems with the audio drivers on an upgrade at the beginning to 10 Windows on another laptop HP and I understand that this issue has been resolved with HP laptops with Windows 10 which are not upgraded.

  Thank you

  Hello

  Can't get HP Envy 17 - So13ca (oh) but HP Envy 17 - S013ca (zero). The following link shows its specifications:

  http://support.HP.com/in-en/document/c05187473

  She has 10 Home 64-bit Windows pre-installed.

  Kind regards.

• How will I know whether or not the home Preium is 64 bit version?

  I'll update my memory, but do not know if my version of Vista is 64 bit or not. I'm under the home edition with Service Pack 2 Premium. System info tell me if it is 64 or not? If that's the case then I guess I have the 32-bit version and will move to 7.

  Help please

  How will I know if my computer is running 32-bit or a 64-bit version of Windows?

  To find out if your computer is running 32-bit Windows or 64-bit, follow these steps:

  1. System opened by clicking on the button start , clicking Control Panel, clicking system and Maintenance, and then clickingSystem.

  2. Under system, you can view the system type.

  "A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/

• How do I know whether or not the instance is affected?

  Hello
  
  Automatic activity or screenflow how would I know if instance has been attributed to a participant or not?
  
  Thank you

  Hello

  Please find the code below and make the necessary changes in it.

  Write the following code in the workflow activity of automatic screen, but before that you must pass the instanceid as an argument to the screen flow.
  In the process as well as screen brand flow layer an instance instanceid as Intvariable.
  Make a variable instanceidArg of the argument as a Int in the process and screenflow layer and map accordingly so that it will take the instanceid of process layer to the layer of screen flow.

  Assign instanceid = id.number; in automatic business process layer but before the global interactive activity where you maped the screen flow.

  Write the following code in the automatic screen workflow activity.

  logMessage ("= instanceid =" + instanceid); InstanceID is the id of the instance that you had a layer of process.
  ProcessService ps;
  InstanceFilter instF = InstanceFilter();
  ps.connectTo (url: Fuego.Server.directoryURL, user: "", password: ""); In the studio the username and password will be the same
  logMessage ("Connected");

  instF.create(processService: ps);
  SearchScope = instF.searchScope (participantScope: ParticipantScope.ALL, statusScope: StatusScope.ONLY_INPROCESS);
  is the id of the process where you want to know the id of participant assighed
  instF.addAttributeTo (variable: VarDefinition.processid, comparator: Comparison.CONTAINS, value: "/" + "");
  instF.addAttributeTo (variable: VarDefinition.INSTANCE_NUMBER, comparator: Comparison.IS, value: Int (instanceid));
  Instances of [] Fuego.Papi.Instance = getInstancesByFilter (ps, filter: instF);

  {foreach (instance in instances)
  logMessage ("Assigned?:" + instance.participantId.empty);
  logMessage ("instance.participantId:" + instance.participantId);

  }
  ps.disconnectFrom ();

  In the runtime if assigned?: true which means that the instance is not assigned or false means assigned.

  Sidonie

• Disk check does not

  At the start of my Dell Inspiron 1501 laptop with vista I get the following message "checking file system on"c", one of your disks needs to be checked for consistency. Disk check was cancelled. Because this message appeared startup and shutdown has slowed considerably. Any suggestion would be appreciated.

  At the start of my Dell Inspiron 1501 laptop with vista I get the following message "checking file system on"c", one of your disks needs to be checked for consistency. Disk check was cancelled. Because this message appeared startup and shutdown has slowed considerably. Any suggestion would be appreciated.

  The system said to do a check disk.

  Here is the tutorial to do disc check... chkdsk.
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  If the tutorial seems to be a bit confusing, try my version...

  Start button > in the search box, type cmd > turn to upper-left, done right click on cmd.exe click on Run As Administrator > in the window black and white, at the prompt of flashing, copy and paste this command line... chkdsk/f/r
  * note: there is a space between 'chkdsk' and ' / '.

  > Press the Enter key > you will see a message that says: he can do right now, but you want to reboot (I am paraphrasing) > type Y as in Yes > press > release cmd wind > restart your computer.

  Check the disk will begin to run at startup > do not stop the computer > it will take a while > just wait > the computer will restart when done.

• How can I fix an appwiz.cpl is corrupt problem?

  I am running Windows 7 Service Pack 1 Professional on an HP workstation.

  My computer has been set up to automatically install updates

  I have anti virus installed = Macaffe and it is up-to-date.

  My network printer has stopped working on the workstation, so I did a search and came up with a difficulty that says to turn on the Windows Firewall on and reinstall the network printer. I couldn't turn off the firewall, so I looked in my event log to see if there was something there.

  The event log shows that there is an update, but the Update Manager has been altered.

  I downloaded the update Fix - it program, and he could not solve the problem.

  I did a system restore to a date earlier, when updates were not working and tried to check the updates. I couldn't do that.

  I ran SFC could not fix all the problems, I posted the CBS and it shows that Appwiz.cpl could not be fixed.

  I have another copy of W7 on my computer, but this is for a few years I started.

  HP installs a system on the computer disk and I don't have the original HP diskettes to initialize and install all programs provided CV.

  I have more than 60 programs installed on your computer and another 80 GB of data I don't want to lose.

  I called Microsoft and they want to sell me a service plan. They said it's a registry problem.

  How can I fix this without destroying all my programs and data?

  Hi Tom,

  Thanks for the update and good to hear that the problem has been resolved. I appreciate the effort made by you in order to solve the problem.

  Please feel free to answer in the case where you are facing in the future other problems with Windows.

  Have a great day!

• disk errors check utility

  I run the disk error control utility to check if there is no problem with my drive C. I have the option "analysis and recovery disk bad sector. The utility is run at the end of phase 2, but has failed to complete. I run the utility even twice, with the same result. Could someone help?

  error message is displayed:

  Windows could not complete the disk check

  
  

  
  

  Please provide additional information on your system:

  What is your system brand and model?

  What is your Version of XP and the Service Pack?

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, Defender, ZoneAlarm, PC Tools, MSE, Comodo, etc..

  The afflicted system has a CD/DVD drive work?

  You have a true bootable XP installation CD (it is not the same as any recovery CD provided with your system)?
  You run this disc control because you have a problem of practice?
  If you're having a problem, you see that you don't think you need to see?  What do not you think that you should see?
  When chkdsk runs automatically restart either because XP thinks he needs to (perhaps your NTFS volume has been marked as dirty) or you have chosen to do
  it yourself, the results appear in the viewing Application event log.  You should look there for the chkdsk log and no problems after running chkdsk.
  To view the logs in Event Viewer, click Start, settings, Control Panel, administrative tools, event viewer.
  A shortcut to the event viewer is to click on start, run and enter in the box:
  %SystemRoot%\system32\eventvwr.msc
  Click OK to launch the event viewer.
  Search the Application log for an event originally by Winlogon, something like:
  Event type: Information
  Event source: Winlogon
  Event category: no
  Event ID: 1001
  Date: 04/08/2010
  Time: 11:25:57
  Description:
  Checking file system on C:
  The type of the file system is NTFS.
  One of your disks needs to be checked for consistency. You
  may cancel the disk check, but it is strongly recommended
  that you continue.
  Windows will now check the disk.
  Cleaning of minor inconsistencies on the drive.
  CHKDSK checks Usn Journal...
  Audit of the USN Journal is complete.
  39070048 KB total disk space.
  28017948 KB in 100571 files.
  56540 Ko 10556 index.
  0 KB in bad sectors.
  236440 KB in use by the system.
  65536 KB occupied by the log file.
  10759120 KB available on disk.
  4 096 bytes in each allocation unit.
  9767512 total allocation on the drive units.
  2689780 allocation units available on disk.
  Windows has finished checking your disk.
  Please wait while your computer restarts.

  Do, or do not. There is no test.

  I need YOUR voice and the points for helpful answers and propose responses. I'm saving for a pony!

• How to stop disk check to run every time that windows vista starts?

  How to stop disk check to run every time that windows vista starts? I had a problem with one of my backup disks so I removed it, but now the drive is still running a disk check whenever I boot my system. It takes so long to run and there is no error, but it starts every time. Why and how can I make sure that she? I read similar questions, but they don't tell you how to run a disk check, they mention however that "If you want to cancel the regular disk for some reason check, check out this guide." but tell you what guide or link?

  Hello

  This tells you how to enable and disable it:

  How to difficulty Chkdsk will not run at startup in Vista
  http://www.Vistax64.com/tutorials/130824-CHKDSK-will-not-run-startup-Vista.html

  Video: Stop Check Disk from constantly running at startup in Windows Vista
  http://blogs.TechRepublic.com.com/itdojo/?p=193

  ChkDsk runs every time Windows starts.
  http://www.WinVistaClub.com/T20.html

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Startup MacBook Pro-comment problems prevent health going to disk/check once again

  My 13 inch Macbook Pro running OSX 10.9.5 (said mid-2012, but it was purchased in fall 2014) has had problems starting

  A few weeks ago the computer is stuck on the loading screen (white, with the Apple and the buffering of spinning icon) without marketing properly. After you have manually turned off and left for a long time he worked well on the next test, so I took care of it has been saved and so didn't think much, and it works pretty well in recent weeks, sometimes being a little slow but that very occasionally and not debilitatingly so and it probably is not related to this problem.

  This morning it was still once stuck on the loading screen, and try again in 5 or 6 times solves nothing. The VRAM reset did not help either. After an attempt to boot into safe mode (filled a little progress bar then disappeared and the computer continued to buffer without purpose), I once again reset the NVRAM and tried a different boot safe mode, with the same results. But this time I left it half an hour or so and on the next attempt (start normally) it miraculously worked a new and everything seems functional. After a new backup with a preparation period slightly extended backup (at least half an hour on the first abandoned attempt, then at least 15 minutes, until correct on the second trial has started), although it is common on my computer, I have enough fear turn the computer off and tempt fate again, if I want to see what can be done now.

  What should I do to check the health of the disk, potentially fix it, find out why this is happening and avoid this problem again in the future?

  I decided to watch from the disk utility and am confused by the Setup program. There is an 'APPLE HDD Media HTS541010A9E662' entry in the list, with a "MacIntoshHD" paragraph below, and both have different information displayed... I ran check disk on the higher level entry and it seems to be out very well ("the Volume Recovery HD seems to be OK"), but I haven't run one on the low level input as it says my computer may be "slow and unresponsive" while doing so, and I'm not entirely sure of what use there.

  It cannot be storage associated with as I stil have 610 gb of free 1 terra (although a large part of what I have (130 GB) is in the other category for a reason any).

  How to fix the slow down time and start. | MacTip.net

  Resolve startup issues and perform maintenance on disk with disk utility and fsck

  Difficulty of slow start in OS X | MacFixIt - CNET Reviews

  Repair the hard drive and permissions - Yosemite, Mavericks, Cougar or Lion

  HD recovery start:

  Restart the computer after the ring, press in and hold the ORDER et R keys until the menu screen to appear.

  Repair

  When the recovery menu appears, select disk utility and press the continue button. Disk utility charges and select Macintosh HD entry indented from the list on the left.  Click the first aid tab, and then click the repair disk button. If disk utility reports any errors that have been corrected, then again run repair disc until no errors are reported. If no errors are reported, click repair permissions . Wait until the operation is complete, then quit disk utility and return to the main menu. Select restart from the Apple menu.

  Ways to help make a slow Mac faster

  17 reasons why your Mac runs slower than expected

  Slow performance of Mac? This Article addresses!

  Difficulty of slow start in OS X | MacFixIt - CNET Reviews

  How to fix the slow down time and start. | MacTip.net

  6 easy tips to speed up OS X Yosemite on your Mac.

  Avoid using third-party software that claims to clean your computer. This software does more harm than good. In addition, you don't need it. Note that all computers become slower over time even in the normal conditions of use. Generally, the experienced users erasing the hard drive and do a clean install from scratch at least once a year or every time that the installation of a major upgrade of the OS. Well sure doing so also means that you need to maintain regular and several backups.

  Add more RAM or reduce the number of simultaneously executed from applications and utilities. Remove unnecessary software such as anti-malware and that promises to clean your Mac. Look for the runaway process: Runaway applications can shorten the battery life, affect performance and increase the heat and fan acti... See also:

  Before Mavericks

  Open the activity monitor in the Utilities folder.  Select all processes in the drop process .  Click the % CPU column heading twice to display in descending order.  If find you a process that uses a large amount of time processor (> = 70,) then select the process, and then click the quit icon in the toolbar.  Click the force quit button to kill the process.  See if that helps.  Don't forget to mention the name of the runaway process, so you can find the cause of the problem.

  Mavericks and later versions

  Open the activity monitor in the Utilities folder.  Select all processes in the menu display .  Click the CPU tab in the toolbar. Click the % CPU column heading twice to display in descending order.  If you find a process that uses a large amount of CPU %, then select the process, then click on the quit icon in the toolbar.  Click the force quit button to kill the process.  See if that helps.  Don't forget to mention the name of the runaway process, so you can find the cause of the problem.

  The ultimate solution

  Back up everything, wipe the drive, reinstall OS X and restore your data from backup. Reinstall the third-party software of original/zero media.

  Start the computer in Safe Mode, and then restart normally. It will be slower than a normal startup.

  MacIntel: Reset of the controller (SMC) system management

  Reset the PRAM and NVRAM on your Mac.

  Now, download and install the update of OS X Mavericks 10.9.5 (Combo)

• XP Home "Disk Cleanup" utility

  I used the 'Disk cleanup' utility for the maintenance of the machine. Have all the boxes checked but the 32 KB in "files WebClient/Publisher temporary ' does not, never. It does not seem to exceed this amount. Someone at - it information on how to erase it or why it is not compensation. I searched the web and found a few suggestions, but some are a little scary. Thought I'd check here too before you continue. Everything disappears as it should when you use the utility. Also, it will be safe to delete these files without any adverse effect on the computer? Thanks in advance for suggestions.

  Rhamnar86It

  I used the 'Disk cleanup' utility for the maintenance of the machine. Have all the boxes checked but the 32 KB in "files WebClient/Publisher temporary ' does not, never. It does not seem to exceed this amount. Someone at - it information on how to erase it or why it is not compensation. I searched the web and found a few suggestions, but some are a little scary. Thought I'd check here too before you continue. Everything disappears as it should when you use the utility. Also, it will be safe to delete these files without any adverse effect on the computer? Thanks in advance for suggestions.

  Rhamnar86It

  This should clear the air: _ http://www.help2go.com/Tutorials/Windows_Errors/WebClient_Publisher_Temporary_Files: _How_to_delete_them.html

  And 32 KB is a VERY tiny part of the hard disk.

• Disk check frequently, but not consistently on boot up.

  After letting the disk check run sometimes check once again the next time you start and sometimes will be going for a while before disk check to run again.  How can I solve this problem?  I use Windows Vista Ultimate Edition on a Toshiba Satellite laptop.

  Backup your stuff.

  Search for hard to specific hard drive diagnosis from any manufacturer of disk utility.

  Use it to test questions.

• The disk check does not not on the external drive

  I am restoring a backup to an external drive, the drive seems to work very well.  However, the backup stops showing communication errors.  The software company was told to run the check disk on the external hard drive.  I click Start and nothing happens.  Device Manager indicates that the drive works properly.  It's just Check Disk does nothing.

  How do check drive working correctly?

  These are the drives on which you were trying to run chkdsk?  If so, the problem may be with the electronics in the case rather than the drive itself.  See, for example, http://www.tomshardware.com/forum/id-1979433/open-lacie-porsche-design-9230-case.html

  So really, they both failed completely at the same time, it's unfortunate and unusual (unless there was some common external factor).

  Although hdtune is a good utility, it might still be useful to check with Seatools (LaCie was bought by Seagate several years ago) - unless the drive makes strange noises when it is turned on. in this case, more you do, the data you will lose.

  Depending on the amount of data is worth to you, it has undertaken is specialized in recovering data on damaged disks.  This service is not cheap.  DriveSaversis probably the most well-known, but there are many others, including one that says it specializes in hard drives LaCie.  Many will give you a free estimate of the costs to retrieve data.  I have no personal experience with any of these companies and none of them can recommend at the expense of others.

• HP Pavilion Dm3 Notebook PC: hard disk Check Fail

  Hello

  Currently I have problems with my PC. When I start at least 95% of the disk is used.

  I run a disk check test on which startup fails to provide me the code error 9C0FL4-50886J-XD7Q21-618303.

  Also when I am invited, through the support site, to run a self test of main HDD on BIOS that also could not provide me with an error code #303.

  I'm stuck reallyt.

  Apart from the full use of the disk all the time, which leads to the computer running slowly, I want to solve this problem.

  It of an old computer but would like to solve this problem, in the short term, so that I do not buy a new one immediately.

  Help, please!

  Max

  Hello

  This seems a lot outside of the fact that it is not provided in the United Kingdom, which is where I am based.

  Are there alternatives to replace the summer completely hard drive? As something I could do with the computer its self. I was invited was the problem when I upgraded to windows 7 to 10?

  If there is no alternative could you link me to a replacement that I could buy from Britain.

  Separate these things, if I go to the track to replace how to transfer what I have on that hard drive to the new without causing the same issue.

  What is the real problem that I have here?

  see you soon,

  Max

• Error Disk Cleanup utility

  the utility disk cleanup on my laptop has authorized the necessary files, a lot of films and documents on mine and my disks hard partners, how to restore these? Help, please!

  Hi Jess, this article will be may be of interest:

  http://www.pcreview.co.uk/forums/need-help-uncompressing-disk-cleanup-damage-t3559893.html

  That explains how to unzip the files (if all goes well, they're still on your system). It is not a feature I used with XP.

  Otherwise if this does not help, then back for backups.

  And believe me, I know what you mean when it's not "my day"! I'm not really having a good week.

  K