I'm trying to connect my photosmart 2610 to a wireless network. Following the online instructions, I have

Similar Questions

• Once I connect my Photosmart C4780 to my wireless network, I lose everything internet.

  My router is a Netgear WNDR3700v3 with firmware version V1.0.0.22_1.0.17.  I can get internet to work on my HP pavilion dv7 with windows 7 64 bit, my smart sony TV, my xbox 360 and a phone that I connect to my wireless router.  The second, I configured my HP Photosmart C4780 wireless router I lose internet on all devices.  I can connect to the router again but can't get out to the internet. What would be the printer could prevent me from accessing internet?

  We will set an IP address of the printer:

  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') 250
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the gateway.
  -Enter for the first DNS 8.8.8.8 and 8.8.4.4 for second DNS.
  -Click 'apply '.

  Now, stop the router and printer, start the router, wait, and then start printing.

  After that, you will have to redo 'Add printer' using the new IP address.

• I tried to make calls through yahoo in vain, despite you follow the video instructions.

  I start with yahoo messenger by selecting actions, video call - my online contacts - call ringtone goes on seconds, then stops. Why?

  What I'm saying is that your problem is probably with Yahoo.  Yahoo is not Microsoft.  If you have problems with applications created Yahoo, you should look at using Yahoo.

  If you have a Sony TV and that you connect a Sanyo DVD player and whenever you play a DVD, he jumps at the beginning of the film after 10 minutes - you would probably not call Sony for help with the DVD player.

  Same concept - just more virtualized and may be stacked.  Yes - your Yahoo product is installed on a Microsoft product.  So it could be a problem in Microsoft - which is why I asked if there was a reason you came to believe it was the Microsoft product rather than the product of Yahoo who seemed to be all your question was.

  I guess these are the instructions that you use?
  http://help.Yahoo.com/kb/index?locale=en_US&y=PROD_MSNG&page=content&ID=SLN1043

  Pay particular attention to this part:
  "In addition, in order to start a video call with another contact both users must have the latest version of Yahoo! Messenger."

• HP G72: connect my computer hp laptop for wireless network printer (4620 series all-in-one hp)

  I tried several times to connect to my printer wireless in the House and I always feel bogged down in technical language that is foreign to me. Questions asked, like URL, addresses and others and I don't have any idea where to find this info.

  I intend to try and install this printer one more time so mget the specific questions I need answers to, so bear with me please. Will be later.

  delnann

  While we're waiting to hear from you @7delnann7; Although I'm not sure of the question, you are experiencing or questions you have, I suggest running printing HP and Scan Doctor because this may require a very easy to use and useful.  HP printing and doctor Scan is a free utility (tool) that allows to quickly resolve problems printing, scanning and connectivity, including but not limited to:

  • Connectivity:

    USB: Check that the USB connection from your computer to the HP product works properly.

    Network: Verifies that the network connection between your computer and your network is working properly.

  • Device Status Test: checks the errors of the device, such as paper, paper jams, stands transport and paper issues and provides instructions to resolve the error.

  • Driver: checks the driver missing or corrupt files.

  • Device Manager: check the problems in Device Manager that could prevent printing.

  • Device online: check if the product has been suspended or put in offline and then sets the State back in line if necessary.

  • Print queue: checks and clears pending print jobs in the print queue (a newspaper for printing waiting to print).

  • Port Match: check the port settings for the HP product.

  • Device conflicts: check the conflicts with other drivers, such as the other brands of printers.

  • Ink issues: check the cartridges and the ink levels for issues that affect the print quality.

  • Print settings: check and adjust the print quality settings.

  • Test print: print a test page for the assessment of the print quality and provides options for cleaning and if necessary print head alignment.

  • Scan tests: check the scanning mechanism, drivers, and registry entries.

  Source: try the HP Print and Scan Doctor for Windows

  Click here to download and run the print and Scan Doctor > > www.hp.com/go/tools

  If this does not resolve the problem, after back and let me know if there are all the symbols except the Green checkmarks and what they are next of course. The key is not always easy to find the key and the box are in the green circle.

  • If you see only the Green checkmarks (), the tool did not find any problem.

  • If you see green sides (), the utility identified a problem and fix it automatically.

  • If you see yellow exclamation points (), the test failed and requires monitoring of the user, but the step was ignored.

  • If you see a red X (), follow the onscreen instructions to fix the problem.

  Thanks, I look forward to hearing back on your part. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message.

• I'm trying to access a wireless network with the password provided for me. I get the following error message

  I'm trying to access a wireless network with the password provided for me. I get the following error message: "the network password needs to be 40bits or 104bits depending on your network configuration. This can be entered as 5 or 13 characters ascii or hexadecimal 10 or 26. "what does this error message mean and how do I address so that I can access the wireless network?

  I use XP Professional with service pack 3. I get this error message every other time I try to log in to a protected wireless network security. I used to not get this message; but, now, it may be impossible, sometimes to call all wireless providers when I might only need for a short period or after hours service opening.

  In addition, it is my computer that requires the network password to be different, not the provider of wireless. A password is given to me who works for other users, but my computer won't let me use it.

  Hello

  I suggest you to visit these links and check if it helps:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-networking/the-network-password-needs-to-be-40-bits-or-104/f3fdc3ee-CB40-4107-A632-082093dcdcb8

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-networking/need-to-connect-to-home-wireless-network-Windows/5bf37a22-cc42-4a0f-9d15-83e780f00123

  It will be useful.

• I can't connect to the Internet via the wireless network. It shows that I have local access only. I can't connect even in SafeMode with network.

  I can't connect to the Internet via the wireless network. It shows that I have local access only. I can't connect even in SafeMode with network.  I have Ping www.microsoft.com and the answer is "ping request could not find host www.microsoft.com.  I am connected to the network wireless through my iPad and can connect via my smartphone. This leads me to believe there is only something configured properly on my laptop. Can anyone provide assistance?

  Hello

  You can try a system restore...

  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  .. .choose time, until this problem (you may tick to show more older restore points).

  Tricky

• They sent me a serial number for a windows version of PS Elements when I ordered a mac version.  The serial number does not work, it is not surprising, but they don' t seem to care.  I tried the online chat and have been waiting for almost a day unanswere

  They sent me a serial number for a windows version of PS Elements when I ordered a mac version.  The serial number does not work, it is not surprising, but they don' t seem to care.  I tried the online chat and have been waiting for almost a day unanswered.  What should I do?

  Look here

  Product order | Platform, language Exchange

• Trying to connect a Photosmart 6520 e to a Mac with OS10.6.8 wireless.

  Recognizes the printer on the network and connect to it (I downloaded the software update). The computer does not see any of the printer. I hung it with USB and he could see the printer and print but I need the wireless connection. The internet rounter is Comcast and it is connected to an Apple Airport Extreme. Have restarted printer, router, airport and computer. Any ideas? Thank you

  Hi morgan149,

  The printer has a valid IP address (example: 192.168.1.101)?

  If so, can you type the printer IP address into Safari and see the information about the printer of the EWS - embedded Web server?

  Follow the steps outlined in the document below.

  Installation of the software of the printer for a wireless network connection

• Photosmart HP 7520: All wireless network devices will lose connectivity after printing

  Dear all, 
  
      I have a problem with my HP Photosmart 7520 printer where all wireless network devices will lose connectivity after a printer has been sent to the printer.
  
  * Summary
  Wireless network unusable after sending one print to HP printer
  No device ( computers nor smartphones ) can use the Internet nor access internal networks ( 192.168.0/24)
  
  * Details
  Turn HP printer on.  ( wireless direct is off - never turned on )
  HP printer connects to working wireless network.
  Other devices ( phone/computers ) already connected and working.
  From any device, send a document to the printer.
  Printer prints document successfully.
  Immediately after printer has printed all devices cannot access internet IP range ( including HP printer ) nor Internet nor router ( 198.168.0.1 ).
  
  * Reproducibility
  Always
  
  * Work around
  Disconnect all devices from the network.
  Power off printer.
  Reboot Internet router.
  
  * Attempted solutions
  Removed wireless configuration.
  Factory reset.
  Added wireless configuration back.
  Powered on and off printer.
  
  * Printing tested with
  Tested with Macbook10.11/Windows 8/Ubuntu 12/Android 4.4.2
  
  * Not tested
  Ethernet cable directly connected to router.
  
  * Internet Router
  Netgear CG 3700
  

  Number of brand and model of the router?

  These settings are to set up your printer wireless (or wired):

  • Stay connected to your router
  • Trouble printer status 'offline '.
  • Wake mode 'sleep'
  • All wireless devices stay better connected

  While the DHCP is convenient, devices like printers (wired and wireless) should always be assigned a (fixed) IP address manually to avoid conflicts on your wireless network and must be outside the range of the router DHCP.  After the adjustment of the static IP address the computer must be updated to show a Standard TCP/IP port with the IP address of printers under printer properties/Ports.

  1. Set a static in the printer IP address (click here) outside the range of the DHCP of the router (check your manual). It is for Linksys routers, but can be used for all routers. Check your DHCP range and change this first if necessary. More Help Wireless Printing is here and here and still more here.  Video here explains the problem and how to solve the problem. <--> So watch this!
  2. Or check in the printer "Auto Off/sleep/Energy Saving Mode" is disabled the System Mode Time Out is set to zero (0) Use the built-in webserver (EWS) by visiting the printer address IP address in the address bar of your browser, click on settings tab/Auto Off. Or use the printer, printer Home Page (EWS) Wizard. Also check your printer properties.
  3. If the printer supports and has IPv6 enabled, disable the IPv6 option in the printer.
  4. Make sure that the printer is connected directly to a socket wall and not to a UPS, power strip or a lightning arrestor. This will cause the printer to drop offline connection and disconnection (checked yes!).

  Additional measures to take if you continue to have the problem (if they are posted)...

• I tried to connect wifi with my laptop, including wireless I use for a month now, but shows only 2 blue screens without the world down on the right, and he said "unidentified network".

  "Unidentified network".

  Hello, today I tried to connect to my friends wifi with my laptop, including wireless I use it for a month now and its impossible! Down right it shows only 2 blue screens without the World Cup, and he said "unidentified network"! I tried several solutions, I found online as 'install the protocols Internet 4 and 6', make sure that I have the ip auto get same restore point system and safe mode with network! Nothing works... my friend connects with his laptop and I can connect with my smartphone, except my laptop! I have windows vista... Please help me thanks

  Go to: Control Panel, Manager of Devic, adapters to extend your network, click with the right button on your wireless network and click on uninstall.

  Do not put a check in the box: remove the software driver for this device.

  Restart your computer and Windows will install your wireless network.

  If the problem persists, see if your computer manufacturer has an updated driver.

  These articles may help:

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  http://support.Microsoft.com/kb/313242

• Im trying to connect an external display, but it will appear on the screen why is that

  After replacing my hard drive I tried to connect my laptop to my external screen I could before and now, just a blue screen on my other screen will not appear, but the laptop still detects

  Update your graphics card driver and try again.

• Trying to connect using a 4 G Verizon Wireless USB Modem

  I'm tying to get an internet connection through my company of Verizon Wireless, with a 4 G USB Modem.  The latest information I got from them were to download a newer version of the VZ Access Manager from the internet.  When I did all downloaded correctly except the pilot does not, and then I learned that he was a "problem of Microsoft in all areas" and that I had to download a Pack from XP Smart.  However I get my updates on a regular basis and have done everything in my power to get my Vista Home Basic 32 Bit updated computer and keep says he is up to date and that the driver works correctly.  I have connected wih this unit for a day and 1/2 then it stopped working and I have not been able to operate since.  I logged until I downloaded the new version of VZ Access Manager.  I've uninstalled and reinstalled the software several times and have changed my USB port as well and even luck now, any ideas.  The new version has been for Compuers using Vista 32/64 and Windows 7.

  Hello

  Do you have an error message when you try to connect to Verizon Wireless USB Modem?

  Send the request in the Verizon wireless Support for assistance.
  http://support.verizonwireless.com/CLC/

  Hope this information helps.

• MacMini don't auto connect to the preferred wireless network when the router reboots

  My MacMini is located to join my favorite wifi network. Where I stay, there is usually a power failure close to a minute or two during the day.

  My setup is such that my MacMini running 24 x 7 with a backup uninterruptible but my router (AirPort Express) turns off during the power outage. When the router goes off, my Mac disconnects from the network which should, but now when my router turns, the MacMini reconnect to the preferred network.

  It shows the network preferred list, and when I manually click on this subject, it reconnects immediately without asking for password. But this will not happen automatically.

  If I restart my MacMini it reconnects very well. The problem occurs only when my MacMini is but my router restarts.

  To reproduce this problem on your side, just turn off your router and once your Mac disconnects from the network back on the router. See if your mac reconnects to your wifi fine.

  Any solution or advice for this problem?

  Thank you.

  Please test after taking each of the steps that you have not already tried it. Stop when the problem is resolved. Back up all data before making any changes.

  1. If possible, test at another network, such as a public access point or hotspot created by a mobile phone. Some Wi - Fi routers are not fully compatible with Apple devices. More specifically, the security mode for the network, as shown in the network preferences window, should be 2 personal WPA or WPA 2 Enterprise. If the router doesn't support either of these modes, it should be replaced with another.

  2. make sure that the network is on the list of favorites by following these instructions. It is important to read the article, as it is the starting point for further efforts to solve the problem. If you skip any step, the problem cannot be resolved. Make sure that the box marked

  Remember this computer has joined the network

  is checked.

  3 follow the instructions in this article to support.

  4. reset the PRAM.

  5. take note of all your parameters of connection Wi - Fi in the network preferences pane, then remove the connection in the connection list and re-create it with the same settings. This by clicking on the icon of the lowest sign from the list of connection, select Wi - Fi as the interface in the form that opens. Select join the other network in the network name menu, then select your network. Enter the password when you are prompted, and then save it in the keychain.

  6. in the menu location at the top of the network preferences window, select Edit locations. A sheet will fall. Click on the plus sign to create a new location. Give it the name of your choice. In the new location, set up the Wi - Fi service with the same settings that you used before. Click on apply and test.

  7. run the Keychain Access application. Find and remove all the network password AirPort elements that refer to the network. Make a note of the password first.

  8 turn off the Bluetoothand the test.

  9. reset the system management controller.

  10. This step should not be necessary, but he has been advised by the Apple Support in some cases, apparently as a solution for a bug. Open the energy saving pane in system preferences. If necessary, click the lock icon in the lower left corner to unlock the settings. When prompted, enter your administrator login password.

  Select the Power Adapter tab and uncheck the boxes marked

  Continued access to the Wi - Fi network

  and

  Enable the NAP...

  If it is present. Then, if the computer is a MacBook, select the stack tab and uncheck the box

  Enable the NAP...

  11. reinstall OS X.

• Pavilion 14-ab051tx N4G24PA: unable to connect to any wireless network after the upgrade to Windows 10

  I recently bought a 14-ab-51tx Pavilion N4G24PA, this is my first laptop from HP, it comes with Windows already installed 8.1 and it worked fine.

  The thing is, I kind of get used to using Windows 10 on my previous laptop, so without further hesitation I upgraded to 64-bit Windows 10.

  Here's what I did wrong:

  Instead of update Windows 8.1 for Windows 10, I indeliberately he installed fresh, with couple of mouse clicks, I didn't realize that I also remove the recovery partition.

  I realized only after the installation process is complete, but then it was too late. I look forward to using my laptop with Windows 10 freshly installed inside to make some games just noticed that I couldn't connect to any network without wire, House or public. It recognizes my wifi at home, but the signal bar is bizarre, there is only 1 bar of signal even if the wireless router is only about 10 feet from him, so I checked my other computers and smartphones, but the signal on them is ridiculously high (full bar), it also detects another wireless network that are further away than my wireless router.

  But back to my HP laptop, I tried to connect to my home network despite the signal bar with the right entry security key, but it does not connect, it says "Cannot connect to the network".

  Tried updating drivers with HP Support Assistant and no luck, the problem persists, tried all the solution on the internet, int ip reset, reset winsock, checking and unchecking, always without success.

  Can someone help me please...

  Hello:

  The BOM indicates that your laptop comes with a Broadcom wireless card.

  Have you tried the last W10 driver for this card to support your PC and driver page?

  This package contains the Broadcom Wireless LAN drivers for the laptop models running a supported operating system. Broadcom wireless LAN drivers are required to activate the built-in Broadcom wireless LAN adapter.

  Exit the: December 17, 2015

  Version 7.35.317.0 Rev.A

  File name: sp74241.exe

• F4580, printer: unable to connect F4580 to wireless network after the upgrade of Virgin Media nowhub

  My printer HP F4580 was connected to my network without wire from Virgin Media Superhub. Then I upgraded to the latest Supehub2 of VM (150 MB/s) but the printer does not now connect. We have 2 Macbooks that connect ok for the SSID of 5 Ghz and a cell phone that connects ok for the SSID of 2.4 Ghz. The printer is WPS enabled and therefore the network. I tried to add the printer to the network using the two WPS push and entering the PIN for Client in the VM Supehub Wireless Manager, but neither work. When I get the F4580 to print the wireless network test report prints a WPS PIN and details for the VM in 2.4 GHz network (auth WPS - PSK, AES/TKIP encryption) sees it. The report includes the SSID for my previous network in the configuration summary. I don't seem to have another way to connect elsewhere WPS push or PIN customer WPS.

  In Manager machine virtual Supehub mode wireless 2.4 GHz network is defined as up to 144 Mbs, but it makes no difference if I put it up to 54 Mbit / s. The Security Mode is set to Auto WP, it makes no difference if I put it to WPA2-PSK (AES).  WPS is activated, and push the WPS button on the Supehub flashes when I use WP Push or enter the PIN code of the customer. In both cases, the I pressed the F4580 wireless button so that the indicator wirelss light flashes then than the VM, push the button flashes. Can anyone help?

  I solved the problem of (re-) install the printer on a Windows PC on the same network, using the CD for the printer. The installation allowed me to select the network, and set up the printer for wireless use.