I need a midi cable or both, in order to synchronize the hearing with an external hardware sequencer?

Similar Questions

• Printer LaserJet 4100: Should which cable I for Laserjet 4100 connected to the laptop with USB port

  I have the HP Laserjet 4100 printer. I bought a new laptop with USB ports.  What type of printer cable I need to connect the printer to my laptop? Is there some kind of printer cable adapter, or something else that will do the trick?

  I have the same question about my HP Laserjet 1100 printer.

  Thanks in advance for your assistance expected.

  If I remember correctly, the 1100 uses a cable "C", alias MicroCentronics.  Have never seen an adapter for that one.  On the 4100, you can get a USB to parallel adapter.  They are pretty cheap and available at most CESS (Consumer Electronics Super Store) as Best Buy.  Staples and OfficeMax/Office Depot should also wear.  Online is cheaper if you have time to wait.

  The thing with these USB converters is often must 'install' the cable first.  In other words, connect it to the laptop, then wait so he could install, then connect the printer.  Depending on your operating system and if you have correct updates that can be almost instantaneous, and you may not even see it pop on the screen.

  Best idea is that since these are obviously not portable machines, connect them to your router via a network card.  I had the 1100 years and used a cheap 170 X.  I know most recent are available which are faster.

  For the 4100, see if you can retrieve a Jet Direct 620 unit on eBay.  Probably less than $50 and sometimes even as little as $25.  Stay away from the 600, 510 or 615 cards.  Low or as the 600, they can leave your network open to hackers.  No need to get Gigabit cards as they will be well above what the 4100 can handle.

  Now, two of these old devices, processing power and memory can be a problem.  Never try to print documents online.  Save them on your laptop, and then print.  You will probably get communication errors if you print directly from IE or FireFox.

  If the 1100 does not die, not even worth fixing.  Put into a Fuser is a nightmare.  The 4100 will probably work for another 20 years if you keep to clean and replace the rolls before they cause jams.

• Satellite P300 - ribbton need for touchpad cable

  Hello

  I need a ribbon cable for my laptop. The cable is designed for the tablet.
  Laptop model: SATELLITE P300 - 1 to 8
  Model No.: PSPC0E - 1H008EN

  The cable is: HAMBURG - W E235863 AWM 20798 80 60V VW-1

  Thank you

  N

  Hi madnad,

  I think the best way would be if you contact a service provider authorized in your country because they can order all Toshiba spare parts.

  You can find a list of all FSA here:
  http://EU.computers.Toshiba-Europe.com > support & downloads > find an ASP.

  Just get in touch with the guys and explain what you need. I'm sure they can help you :)

• Speed/performance of my mac mini (mid-2010) is very slow. Need help, consolidate the files, software updates, etc. in order to improve the speed and performance.

  My mac mini (mid-2010) speed/performance is very slow - think of it as a result of letting my kids do "whatever" about it in recent years.  Need help, consolidate the files, software updates, etc. in order to improve the speed and performance.  You will also need to get data out of old PowerBook G4.

  < object edited by host >

  We are users like you.  Search locally by using something like Yelp or similar

  http://www.Yelp.com/search?find_desc=Apple+repair & find_loc = Chicago, + IT & start = 0 & ortby = rating s

  or read a few links which may be relevant on this forum about the slow mac mini

  http://BFY.tw/5C63

• Pavilion dv6 1108sl: Pavilion dv6 1108sl - need for new cables sheet FFC

  FFC 6pins and 9pins ribbon cables that connect the power button and the audio controls on the keyboard to the motherboard are broken.

  Can you give me the exact specificactions to get new cables, as they are not presented in the shop "of HP spare parts?

  If you look here, there is enough of several alternatives: http://www.digikey.com/product-search/en/cable-assemblies/flat-flex-ribbon-jumper-cables/1573391

  I know that they are 6pins and 9pins, but apparent what the length, waist length, thickness, style of endpoints, etc.?

  This forum is my last hope, as the official support of HP is inadequate emberassingly (those incompetent have absolutely no idea what I'm talking about, or the ability to speak in an understandable language without automatic translators!).

  These are the parts you need:

  (2) the switch cover (includes LED card and cable) Moonlight White (replaced by 571747-001 on certain models) Onyx 512829-001 001 518110 Moonlight White (replaces 518110-001 on certain models) 571747-001 Espresso Black (replaced by 571757-001 on certain models) 518790-001 Espresso Black (replaces 518790-001 on certain models) 571757-001

  (3) the power button for computers with a discreet graphics subsystem memory (includes cable) 512835-001 of the power button for computers with memory of graphic subsystem UMA (includes cable) 512834-001

  HP does not identify the cables as a separate part number, unfortunately, and I doubt you'd find anyone who wants to sell it like that.

  Here is for example the Commission affects the cable on eBay:

  http://www.eBay.com/ITM/HP-512835-001-power-on-off-button-circuit-board-w-cable-discrete-DV6-series-/151774362025?hash=item235674f9a9

  These guys have a lot of tips power button so perhaps you could talk to them by sending just a cable or even a picture.

  After back and let us know the color of the switch cover you need and maybe found, too.

• Do I need a sync cable?

  My Palm treo pro that I bought used does not have a sync cable. As much as I know PDF activesync manual is already on the treo pro. On ebay they sell the sync cable and the CD of drivers USB data cable installation together. Or you can buy just the real cable without the USB cable driver installation disk. Should I drive and the cable or just the cable? I currently do not have the software from the disc on my computer. It costs £3 extra for the CD, so if it is available for free download or I did not need its worth knowing. Ebay purchase links are below-

  http://CGI.eBay.co.UK/USB-data-sync-cable-Palm-pixi-pre-Treo-Pro-850-UK-/260534288960?PT=UK_MobilePh...

  http://CGI.eBay.co.UK/USB-sync-charge-data-cable-Palm-Treo-Pro-850-PDA-/220649672409?PT=UK_Computing...

  If you know the answer and can help thanks in advance!

  Thanks I think that its not like you need tell by the sounds of it. Thanks again.

• I try to maintain a "split screen" of two separate windows. Both windows are open on the left and I need an opening on the left and the other to open on the right

  I have a fixed window on the left side of my screen and I need coninuously to open and close a second window on the right side of my screen.  The right window keeps opening on the left on my fixed window.  How can I keep the fixed windows left and right opening and closing (or variable) in place on opposites of the screen?

  Buy a second monitor and install it.

• What is the problem with my iMac mid-2011

  Hello

  Need help find out what is the problem with my iMac to mid-2011.

  Yesterday during a reboot it just never came to life.

  On turning the power on, I get the RINGTONE to start and that's it. The screen is totally black. Nothing behind tried with a torch.

  VRAM rearmament so far I tried repeatedly, unplug and plug, all kinds of combinations of keys in the carillon and nothing.

  Connected to an external monitor and shows nothing of too - no signal.

  Any way that I can know what is wrong with it before sending it to the service tech? I suspect bad graphics card but how do you ensure?

  From what you describe, it looks like a hardware issue that Apple will only be able to resolve, but not to despair immediately.

  Read it please get help with graphics issues on external displays connected to your Mac - Apple Support.

  I know that the title and subject are not suitable to your concern, but buried in this document is the following passage that contains three links describing the steps to follow.

  If you can not change the resolution of your screen because you see no image, restart your Mac in safe mode to reset the default display resolution.

  If booting safe mode doesn't resolve the problem, reset your Mac NVRAM and SMC to reset the video ports on your Mac to their default values.

  That first, then write again for additional suggestions if you are still having problems.

• I want to thank my wifi in another part of the House with an Airport Extreme. But I want to not be connected to the modem main via ethernet cable is it possible?

  I want to thank my wifi in another part of the House with an Airport Extreme. But I want to not be connected to the modem main via ethernet cable is it possible?

  I put in place already to extend the wifi of my modem still connected to the modem via ethernet cable.

  Now I want to be considered on the floor and use it to extend the wifi without ethernet cable

  The AirPort Extreme can extend only wireless signal from another router from Apple, so if you want to take the AirPort Extreme on the floor and extend wireless signal, you will need another airport connected to your modem by Ethernet cable router to produce the wireless signal that will extend the extreme on the floor.

  Another way of saying the same thing would be to say that if you want to extend wireless using a router from Apple, you'll need two of them do... because AirPort Extreme is not compatible with a third-party modem or modem/router for this purpose.

• Satellite Pro A300 - how to get the sound on the TV with VGA cable?

  Hello world

  I have a real problem connecting my Satellite Pro A300 to my Samsung HDTV.
  The video works fine - I used a VGA connection on the laptop and the TV.

  The problem I have is healthy.
  I want the sound either also come from the TV. I tried a jack of 3.5 m from the headphone jack of the laptop to a red and white connection RCA audio on the TV, but it doesn't seem to work.

  Does anyone have any ideas or advice?
  I need of additional drivers, etc., or do some settings need to be changed etc etc.

  Hello

  Normally, to use the 3.5 mm jack plug in the headphones, you need an adapter cable.
  At one end, it has a 3.5 mm jack and the other side to connect red and white audio RCA connections.
  Here is an example of what I mean:
  http://www.optimization-world.com/IMG/prod/3_5_mm_rca_audio.jpg

  I m using such an adapter without any problem. You n t need an additional driver, or something more. It's the same as if you were using a helmet. :)

• Connection Satellite L750D to the TV with HDMI cable

  I tried to connect a laptop L750D to a Phillips TV but none is displayed on the TV and the message on the TV is «unsupported video»

  When I connected the laptop to the TV and turned on the laptop, it's in restart mode and the messages showed on TV, but as soon as windows has started to the top of the screen of the TV turned blue and the "unsupported video" message appeared.

  I then plugged a laptop HP pavilion g series to the TV with the HDMI cable and using the same port HDMI on the TV and the computer screen is appeared on television right now.

  Can someone help me please?

  Hello

  Try this:
  Both devices (TV and laptop) must be turned off but connected with a HDMI cable.
  Then turn on the TV and the laptop.
  After Windows has started, use the Fn + F5 secret key to switch the video output to TV.
  Is this possible?

  By the way: have you chosen the right graphic resolution and supported?
  Don't forget that you TV supports the resolution which has been chosen!

• Migrated domain users are needed to access shared folders on the network with AD username old or need to share with the new AD ID

  Dear Sir

  Migrated domain users are needed to access shared folders on the network with AD username old or need to share with the new AD ID

  I am in a field & I'll migrate with a domain name.

  EX: now I'm in the field of the AAA tomorrow my domain name will change to BBB. User accounts are created in two AAA & BBB and the two domain user IDs are different.

  data servers are also migrating with the new domain.

  is it possible to access share with the old user id folder in new field or both to share the files again with the new user ID Active directory.

  Kind regards

  Chauvet J.

  Hello

  The question you have posted is related to professional level support. Please visit the below mentioned link to find a community that will support what ask you:

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer/

• computer not automatically standby (formerly titled "impossible computer automatically sleep when it is connected to the internet with modem cable")

  Hi, I noticed recently that my computer (Windows XP Media Center Edition 2005) is unable to sleep automatically when it is connected to the internet with a cable modem. Change the settings for my current power mode and try a different feeding regime (diagrams of Windows XP default power and power management, I created) only solves the problem for 2 days at most. I also tried to change the settings for the other power plans mentioned, and yet once again, the problem was only set for two days at the most. I also tried turning off my computer, restarting my computer, recording Powercfg /Restore Default policies in Run, saving sfc/scannow in Run, and again, I got the same result. Reset and power cycling the modem cable is not helped either. To help you better understand the problem, for example, if I had the date set for the screensaver set to 1 minute, the time for the monitor to turn off set to 2 minutes and time for your computer set to 3 minutes, the screen saver activate after 1 minute, the monitor turns off after 2 minutes, but the computer would not sleep mode after 3 minutes , even after an hour or more. I tried to check the Task Manager, and I have not noticed any process that would be interrupting the day before. However, I noticed that when I turned on the monitor by moving the mouse, even when the computer was unable to sleep and unplugged the ethernet cable from the cable modem and waited, the computer has entered standby as it should have.  I tried to find a solution for more than a week, contributions for this issue would be greatly appreciated. Thank you for taking the time to read my post. (Update: it seems that the problem is something else then my cable modem.)

  Hello

  Thank you for the update.

  This behavior can occur because of possible conflicts of third-party software, which includes the third-party security software.

  You can also temporarily disable third-party security software and firewalls installed on the system and check the issue.

  If disabling the antivirus software solves the problem, you may need to configure the settings of the antivirus as a result program. Please contact the software vendor for assistance in this regard.

  Note: be sure to enable the security software on the computer after checking the issue.

  Note: When you perform a clean boot, you can activate services for the modem, network card and disable third-party services to check the issue.

  Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.

• When I try to connect with my wireless laptop will connect only to Local access. If I connect the laptop to the router with the ethernet cable, it works very well.

  VIsta - Local access only

  HI -.
  I recently moved.   I use the same router from my old apartment and I had no problem connection in the past.   Since I moved I have a new Time Warner modem (Cisco) and the modem works fine.

  The router also works very well I'm able to connect with my iPhone and IPad without any problem.

  But when I try to connect with my wireless laptop, it will only connect to Local access.    If I connect the laptop to the router with the ethernet cable, it works very well.

  It's a Dell Studio 15 with Vista.

  The computer is able to connect to wifi to other places without any problem, but for some reason that I can't connect home.   I tried to reset the modem and the router several times, but that did not help.   I tried the option repair & diagnose several times but it doesn't work.

  I tried to look for other solutions online and tried to disable IPv6, and while it helped some and I was able to connect wireless, the computer ran so slowly that it didn't seem like a good solution.

  This has been very frustrating.   Thanks in advance for any help or suggestion.
  Staci

  Hello Staciusa,

  Have you tried to change the wireless channel that your router is running at? There may be interference that could prevent the internet connection:

  Take a look at step 6 in this article that give more details about it:

  http://www.Microsoft.com/athome/Setup/wirelesstips.aspx

  If you need assistance to change the settings of the specific router, you will need to contact your router manufacturer or your internet service provider.

• I connected my computer to the tv using an s-video cable, but I get a tv error message that says that the entrance with no signal.

  original title: pictures playing on tv

  I connected my computer to the tv using an s-video cable, but I get a tv error message that says that the entrance with no signal. I know that I have selected the right input of the TV. Is there something that I need to set up the laptop to send the signal to the s-video connector?

  Perhaps the following links will propose a few ideas:

  How to connect your PC to your TV
  http://en.kioskea.NET/FAQ/Sujet-228-how-to-connect-your-PC-to-your-TV-set How to connect my computer to a TV
  http://hookpctotv.com/ PC to TV cables and adapters
  http://www.SVIDEO.com/PC2TV.html