I tried to connect via / DVI to hdmi and it does not wrk
If I have vga and dvi on my screen but only vga on my computer is - it say that I did not compatible computer to run hdmi to my screen?
Hi lastace,
If your vga port is blue, this means that it is a D - Sub connection.
With D - Sub, you can buy a connector which can convert the output D - Sub to DVI, but unfortunately, not HDMI.
So in your case, you can connect your monitor via D - Sub (VGA) or DVI but not HDMI unless you have a HDMI port your
laptop. Sorry I couldn't give you good news.
I hope this helps!
Tags: HP Desktops
Similar Questions
-
I tried to change my e-mail address and it does not work, I need to contact support to change it for me
Hello
Please get in touch with the customer: -.
* Be sure to stay connected with your Adobe ID before accessing the link above *.
-
HP 14-d037TU HDMI and VGA does not not for WIN7 64 bit
Hello
I came across another issue I solved all the problems of driver for laptop HP 14-d037TU. However, the HDMI and VGA is not working. Help, please.
PCI\VEN_8086 & DEV_0F31 & SUBSYS_218D103C & REV_0A
PCI\VEN_8086 & DEV_0F31 & SUBSYS_218D103C
PCI\VEN_8086 & DEV_0F31 & CC_030000
PCI\VEN_8086 & DEV_0F31 & CC_0300Thank you
Hello:
This driver should work for the graphics.
This driver should install usb 3.0 for the hardware ID you have posted:
-
Urgent: I am trying to open a file of Government and it does not work
Hello! I am trying to open a folder of cic immigration application and it does not work, message says to upgrade the software adobe reader, but when I try to install it says that I have already. Can you help me as soon as possible? Thank you.
Hi nadiat43073873,
Right-click on the PDF link and choose "save link as", save the PDF on your desktop & open it using the Reader app now.
Kind regards
Nicos -
Windows 7 Home Premium does not start and an external monitor connected via DVI to HDMI Cable
I have a Dell Inspiron 531 desktop computer with a NVIDEA GeForce 8400 GS video card. This video card has the following outputs: DVI, VGA and S-video. When I connect it to my computer via the VGA port to PC to my Sony Bravia KDL-40XBR4 monitor port, the machine starts perfectly. If I connect via a HDMI cable to one of the HDMI monitor DVI ports, the screen displays the video BIOS, but turns black when the operating system begins to load. If I connect another monitor to the VGA port, yet once the machine boots fine, but if I connect the monitor to the computer and the Sony Bravia, once again the machine does not start. The strange thing is that if I boot with only the connected computer screen and then plug the DVI to HDMI cable, then Windows 7 sees the Sony Bravia monitor very well, and I can extend the desktop. If the machine mode 'sleep', both monitors work very well to wake up the PC. So, if the Sony Bravia is connected alone or with the computer screen, the machine does not start (the screen will display 'go black' when the OS starts to load.) I tried to run Windows in Mode safe, but he won't either. I have all the updates of Windows applied and have installed the latest drivers from nVidea so.
Hey Chris,
First of all, about climbing, is not a technical support; This is a community forum where MS moderator and contributors are involved. Now to your question ~
It's very strange that the PC does not start when this unit is connected, but works fine when connected after the fact. I've seen several cases where a hardware configuration of uinsusal will prevent a PC to boot. I think that the culprit may be DVI to HDMI Cable that you are using. If I were you, I try to connect the PC to a DVI monitor and see if it boots normally. Also, see if the monitor can prevent another PC to start when it is connected directly via the HDMI.
Good luck! Let us know how it turns out.
-
HP 14 d020la: HP 14-d020la HDMI and VGA does not not for WIN7 64 bit
I've been downdgrade HP 14-d020la laptop for Windows 7 64-bit. Some drivers are ok, but the work is not the HDMI and VGA. Help, please.
Hello:
You need the graphics driver for the CPU/chipset that your laptop... the first driver listed is the automatic driver installation.
https://Downloadcenter.Intel.com/download/24973/Intel-HD-graphics-driver-for-Windows-7-8-8-1-64-bit
-
system displays 2 messages saying 2 large installations cannot be updated. Tried to install and run them as an administrator and do not work.
He does not think I open word, Excel, pdf document or file. Get the following message... Windows cannot find the following file... Please make sure file name is correctly written.
Hello
see if that helps to fix:
How to reset the Windows Update components?
There is also an automatic 'fix - it' here
http://support.Microsoft.com/kb/971058
Also, try to put the KB numbers in the search on the link below and then manually download the
http://www.Microsoft.com/downloads/en/default.aspx
or please repost your question in the correct windows update forum
http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-windows_update?page=1&tab=all
_______________________________________________________
also run the sfc/scannow command.
http://support.Microsoft.com/kb/929833
Use the (SFC.exe) System File Checker tool to determine which file is causing the problem and then replace the file. To do this, follow these steps:
- Open an elevated command prompt. To do this, click Start, click principally madeprograms,Accessories, right-clickguest, and then clickrun as administrator. If you are prompted for an administrator password or a confirmation, type the password, or clickallow.
- Type the following command and press ENTER:sfc/scannow
The sfc/scannow command analyzes all protected system files and replaces incorrect versions with appropriate Microsoft versions
How to analyze the entries in the log file generating the program Checker (SFC.exe) resources of Microsoft Windows in Windows Vista
http://support.Microsoft.com/kb/928228#appliesTo
If SFC detects the main problems it can't fix you may need to borrow a Microsoft dvd vista not an acer, HP etc. recovery disk and do a repair installation
read the below tutorial on how to perform a repair installation
http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html
________________________________________________________
and make sure that your computer is malware free
an anti-virus can not find any problems
you need to scan with a good anti-malware program
Download update and scan with the free malwarebytes anti-malware version
-
DeskJet 6940: ethernet connection between the new modem and printer does not transmit Mac
I just installed a new modem to Qwest; It works wirelessly with my iMac 10.11. My old (but functional until yesterday) Deskjet 6940 is connected to the modem via Ethernet. When I try to print, the document seems to be transmitted to the printer, but then it hangs on and I get the message "the printer is not connected" - which it is, plugged, ethernetted, and set in motion. Support of Qwest says that only 10% of the info from the computer are the printer, but he seems to think that the part of the new modem Ethernet is functional,
I have already tried all unplug/restart/send/add printer new check/updates / IP (cannot connect) / ethernet ports and cables, etc.
Any other ideas?
Thank you!
Hi @newgranny,
Thanks for getting back to me.
It is good that the printer has been able to print a diagnostic page.
Ensure that the router and firewall on the market do not block these ports.
Ports of printing:
- UDP ports: 427, 137, 161
- TCP port: 9100
Card photo upload:
- UDP ports: 137, 138, 427
- TCP port: 139
The HP device status:
- UDP port: 161
Ports of Web Services:
- UDP and TCP: 80, 443, 5222 and 5223
Hello Ports:
- TCP and UDP: 5353 and 5297, 5298
Unplug the wired network (ethernet cable), restore the default values on the printer.
Restore the default settings.
Follow these steps to reset the printer to factory default settings:
1. check that the printer is on.
2. press and hold down the button to report Page.
3 while holding down three times the homepage button, press the Cancel button.
4. release the report Page button.
- Restart the printer.
- Connect the ethernet cable.
- What were the results?
If the problem persists, try the USB connection.
Please reply to this message with the results. Good luck!
-
Connections blackBerry Smartphones Blackberry Apps and Facebook does not
I can't seem to connect to one of my 'apps', including Blackberry Apps World! I entered my password, but the message is not correct. For the world of applications Blackberry, I enter the answer to my security question, and the Blackberry said he's sending a message to my email address for me to reset my password - except that it freezes and nothing happens. For Facebook, once that I entered the password and get the message that this is not correct (even if it's the right password) - there is nothing I can do. No way to reset or change the password. Can someone advise please.
Get you an error or warning when you try to connect to App World? You are also able to connect using your BlackBerry ID to: www.blackberry.com/blackberryid?
On the issue of Facebook, you are able to browse the internet or send and receive email without problem? You are also able to connect to Facebook on your computer? If you can, Facebook for BlackBerry, uninstall then reboot your device. Once it is up go to: www.blackberry.com/facebook for download/install Facebook for BlackBerry, and then test the connection and using the application.
-
Who can relate to Windows
I bought a Hewett Packard printer and it did not work properly so I bact to the store and exchange it for a printer problem.
but before he took back the HP printer I do not uninstall the HP with the HP CD software. After installing the software problem I now the HP conflicking with the software of brothers. then when I want to print something the printer HP appears. My question is I tried to uninstall the program from HP and it does not work. I call the Hewett Parkard Tech. and no help there either. So please give me a direction step by step on how to uninstall the software Hewett Parkrad.
Leon
See if it helps:
Three ways to uninstall and reinstall the software of printer/Scanner Hewlett - Packard
http://www.out-of-warranty.com/three-ways-to-uninstall-and-reinstall-HP/ -
Connect HP computer for my Inspiron 23 via dvi to hdmi
Hi, I was told to connect via div to hdmi cable, but it does not. I don't know how to specify in Windows 8 to accept the HDMI input.
I try to use two computers, using the Inspiron as the monitor
Exactly what 23 Inspiron AIO did you?
Some of them have an option selection of the input source / off button on the side of the screen in addition to. It is this guide Setup for Inspiron AIO 2330 #7, but it is optional on the 2330, and you must check the installation guide for your exact model to see if she was even offered as an option and where it is located.
If you have, you will need to cycle this button to accept the port of video input for the HDMI input (VGA input) signal.
If it will work with the other PC as input source is another question...
-
App store, Safari and iTunes does not connect to the Internet after installing macOS Sierra
App store, Safari and iTunes does not connect to the Internet after installing macOS Sierra
After upgrade 'OS X El Capitan' to "macOS Sierra" window only empty "App store" and page "Safari" made its appearance, no error message shows. store "iTunes" and "Dictionary" does not connect too.
But Google chrome works well.
So have you tried the next steps in your original post that Safari does not work after installing macOS Sierra:
2) Advanced the steps to correct the problems with the iTunes Store - Apple Support connection
-
My mini ipad 4 has no battery completely not discharged, called to the charger, but the system does not start. What should do? Already a time connected to the charger, but the system does not start. I have iPad 3 months and never suffered no damage.
When connected to the charger make a forced reboot: hold the home and sleep buttons, wait for the Apple logo, release the buttons. May take a few tries.
-
HP Envy 23: HDMI in button does not work in Windows 10
After the upgrade to Windows 10, the button used to display HDMI no longer works on my HP Envy 23
I had this same problem, except on the 27xt, which is the version 27 "the envy of HP TouchSmart. It is same as the 23 '' only bigger. I called HP who told me to call Microsoft, which, after an hour of Remote Desktop new installation graphic drivers and who does not, told me to call HP.
So, I googled the problem and found this thread on this forum and I am so glad that I did. Hpuser30 is quite right, except that I found a method even easier for fixing.
I went to my local BestBuy store which sells version 23 "and I plugged a flash drive, I brought home, in the USB 3.0 port on the side of the screen. Then I went on the c:\ drive and found their SWSETUP folder, and I "copied" the entire folder on my flash drive. Their machine works perfectly in Windows 10, so I felt confident that this could work. I went home and opened the SWSETUP folder on my computer and I tried MyHPDisplayOSD and I found the folder named the same thing. Inside this folder is a file called HP_My_Display_2.08.020_Setup.exe.
I tried to launch the file but it said I couldn't, because I already had a newer version. That was the problem in the first place. Microsoft or HP had updated the driver to one that is no longer recognize the HDMI port or button.
And I went to control panel configuration then programs and I uninstalled my HP device, requiring a reboot. Then I installed the Setup file on the Flash drive, I got the computer to BeatBuy. I didn't even have to reboot. I just pressed the button HDMI IN and it worked perfectly, the way it is supposed to.
The version store is 23 "and mine is a 27". The store had 10 Windows Home and I have Windows 10 Pro, but the HP_My_Display_2.08.020_Setup.exe works on both.
So, it isn't the graphics driver and is not the button or port, is this HP My Display driver. The solution is really as simple as that. Now, I have to see if Microsoft or HP update again and it mess... Once again. If they do, at least I know how to fix it. -
TNS-12545: Connect failed because target host or object does not exist
Hi all
I have two hosts with me. 1 host1 and 2. host2. Host1 have ORCL database. And when I'm doing the tnsping to host2 for database ORCL I get error below.
[oracle@host2 ~] $ hostname
host2.example.com
[oracle@host2 ~] $ tnsping ORCL
AMT Ping utility for Linux: Version 11.2.0.1.0 - Production on 5 April 2014 20:31:40
Copyright (c) 1997, 2009, Oracle. All rights reserved.
Use settings files:
TNSNAMES adapter used to resolve the alias
Try to contact (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = host1.example.com) (PORT = 1521)) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_NAME = ORCL)))
TNS-12545: Connect failed because target host or object does not exist
Here's my tns annually involves Details:
on host1:
[oracle@host1 admin] $ listener.ora more
listener.ora # Network Configuration file: /u01/app/oracle/product/11.2.0/dbhome_1/network/admin/listener.ora
# Generated by Oracle configuration tools.
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(GLOBAL_DBNAME = ORCL. WORLD)
(ORACLE_HOME = u01/app/oracle/product/11.2.0/dbhome_1)
(SID_NAME = ORCL)
)
)
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = host1.example.com) (PORT = 1521))
)
)
ADR_BASE_LISTENER = / u01/app/oracle
[oracle@host1 admin] $ more tnsnames.ora
tnsnames.ora # Network Configuration file: /u01/app/oracle/product/11.2.0/dbhome_1/network/admin/tnsnames.ora
# Generated by Oracle configuration tools.
ORCL =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = host1.example.com) (PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = ORCL)
)
)
MYTEST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = host2.example.com) (PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = MYTEST)
)
)
LSNRCTL > status
Connection to (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST=host1.example.com) (PORT = 1521)))
STATUS of the LISTENER
------------------------
Alias LISTENER
Version TNSLSNR for Linux: Version 11.2.0.1.0 - Production
Start date April 5, 2014 20:09:33
Uptime 0 days 0 h 25 min 1 sec
Draw level off
Security ON: OS Local Authentication
SNMP OFF
Parameter Listener of the /u01/app/oracle/product/11.2.0/dbhome_1/network/admin/listener.ora file
The listener log file /U01/app/Oracle/diag/tnslsnr/host1/listener/alert/log.XML
Summary of endpoints listening...
(DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=host1.example.com) (PORT = 1521)))
Summary of services...
Service "ORCL" has 1 instance (s).
Instance "ORCL", State LOAN, has 1 operation for this service...
Service "ORCL. The WORLD' has 1 instance (s).
Instance "ORCL", status UNKNOWN, has 1 operation for this service...
Service 'ORCLXDB' has 1 instance (s).
Instance "ORCL", State LOAN, has 1 operation for this service...
The command completed successfully
On host2:
[oracle@host2 admin] $ listener.ora more
listener.ora # Network Configuration file: /u01/app/oracle/product/11.2.0/dbhome_1/network/admin/listener.ora
# Generated by Oracle configuration tools.
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(GLOBAL_DBNAME = MYTEST. WORLD)
(ORACLE_HOME = u01/app/oracle/product/11.2.0/dbhome_1)
(SID_NAME = MYTEST)
)
)
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = host2.example.com) (PORT = 1521))
)
)
ADR_BASE_LISTENER = / u01/app/oracle
[oracle@host2 admin] $ tnsname.ora more
TNSNAME.ora: no such file or directory
[oracle@host2 admin] $ more tnsnames.ora
MYTEST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = host2.example.com) (PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = MYTEST)
)
)
ORCL =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = host1.example.com) (PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = ORCL)
)
)
Please help me what I do in configuring the listener and tns.
Kind regards
Michel
fb767351-A660-4b18-9a9f-73bc141f6a0c wrote:
Hi all
I have two hosts with me. 1 host1 and 2. host2. Host1 have ORCL database. And when I'm doing the tnsping to host2 for database ORCL I get error below.
[oracle@host2 ~] $ hostname
host2.example.com
[oracle@host2 ~] $ tnsping ORCL
AMT Ping utility for Linux: Version 11.2.0.1.0 - Production on 5 April 2014 20:31:40
Copyright (c) 1997, 2009, Oracle. All rights reserved.
Use settings files:
TNSNAMES adapter used to resolve the alias
Try to contact (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = host1.example.com) (PORT = 1521)) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_NAME = ORCL)))
TNS-12545: Connect failed because target host or object does not exist
If your entry for "ORCL" tnsnames decided to 'contact' indicated info. He tried to send a ping packet to the server identified by "(HOST = host1.example.com)". " Oracle tns transmitted the request to the network stack of BONES for the resolution and routing. Here, 'host1.example.com' host name could not be resolved to an IP address, or if it was, it was an IP address that is a dead-end.
Here's my tns annually involves Details:
We see the details necessary out of your tnsping tns. Since the application never had the host (as is obvious in the error message), nothing about the questions of the listener - he never got.
on host1:
As your example tnsping host2, and says that the error message obvious host1 is nowhere to be found, like the listener, none of the files of configuration on host1 question - demand ever on host1.
[oracle@host1 admin] $ listener.ora more
listener.ora # Network Configuration file: /u01/app/oracle/product/11.2.0/dbhome_1/network/admin/listener.ora
# Generated by Oracle configuration tools.
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(GLOBAL_DBNAME = ORCL. WORLD)
(ORACLE_HOME = u01/app/oracle/product/11.2.0/dbhome_1)
(SID_NAME = ORCL)
)
)
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = host1.example.com) (PORT = 1521))
)
)
ADR_BASE_LISTENER = / u01/app/oracle
[oracle@host1 admin] $ more tnsnames.ora
tnsnames.ora # Network Configuration file: /u01/app/oracle/product/11.2.0/dbhome_1/network/admin/tnsnames.ora
# Generated by Oracle configuration tools.
ORCL =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = host1.example.com) (PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = ORCL)
)
)
MYTEST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = host2.example.com) (PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = MYTEST)
)
)
LSNRCTL > status
Connection to (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST=host1.example.com) (PORT = 1521)))
STATUS of the LISTENER
------------------------
Alias LISTENER
Version TNSLSNR for Linux: Version 11.2.0.1.0 - Production
Start date April 5, 2014 20:09:33
Uptime 0 days 0 h 25 min 1 sec
Draw level off
Security ON: OS Local Authentication
SNMP OFF
Parameter Listener of the /u01/app/oracle/product/11.2.0/dbhome_1/network/admin/listener.ora file
The listener log file /U01/app/Oracle/diag/tnslsnr/host1/listener/alert/log.XML
Summary of endpoints listening...
(DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=host1.example.com) (PORT = 1521)))
Summary of services...
Service "ORCL" has 1 instance (s).
Instance "ORCL", State LOAN, has 1 operation for this service...
Service "ORCL. The WORLD' has 1 instance (s).
Instance "ORCL", status UNKNOWN, has 1 operation for this service...
Service 'ORCLXDB' has 1 instance (s).
Instance "ORCL", State LOAN, has 1 operation for this service...
The command completed successfully
On host2:
Okay, the problem being that a client on host2 couldn't solve a connection to hos1, these could be revealing.
[oracle@host2 admin] $ listener.ora more
listener.ora # Network Configuration file: /u01/app/oracle/product/11.2.0/dbhome_1/network/admin/listener.ora
# Generated by Oracle configuration tools.
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(GLOBAL_DBNAME = MYTEST. WORLD)
(ORACLE_HOME = u01/app/oracle/product/11.2.0/dbhome_1)
(SID_NAME = MYTEST)
)
)
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = host2.example.com) (PORT = 1521))
)
)
ADR_BASE_LISTENER = / u01/app/oracle
Except that in the example, we work with, host2 is the customer, trying to reach a database on host1. Any listener on host2 is totally irrelevant.
[oracle@host2 admin] $ tnsname.ora more
TNSNAME.ora: no such file or directory
[oracle@host2 admin] $ more tnsnames.ora
MYTEST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = host2.example.com) (PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = MYTEST)
)
)
ORCL =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = host1.example.com) (PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = ORCL)
)
)
It's the only tns configuration file that is important for the problem at hand. And we already knew what he said, since the output of your command of tnsping.
Please help me what I do in configuring the listener and tns.
Kind regards
Michel
Is "host1.exampl.com" the real hostname of your machine "host1"? Or you made that blur in your ad - thing quite legitimate to do this for security reasons.
Whatever, this is not really a matter of tns, unless of course 'host1.example.com' is really what you put in the tnsnames file, but your server "host1" became really something else.
Assuming that 'host1.example.com' is the correct value, debugging starts with the following:
[oracle@host2 admin] $ ping host1.example.com
[oracle@host2 admin] $ tracerout host1.example.com
Maybe you are looking for
-
Why I always automatically redirected to the French pages?
When I type an address .com (or any other extensions not French) I get automatically redirected to an address .fr and I really hate this. If I want a French site, I'll ask for it, I don't have others to decide what I want. Sorry, nothing personal, it
-
Program to freeze when closing IE
I am running Vista and IE7. Recently, often when I try to close a site Internet Explorer the computer freezes and my only escape is to close the program running with the Task Manager. any suggestions?
-
Impossible to uninstall Windows Essentials
I'm trying to uninstall the latest version of Live Essentails but when I click on uninstall in Control Panel, nothing happens.
-
I have windows 7 64 bit, my mm2012 works fine, when it finished burning my movie, asked another copy that I did, but when I played in my player, it has no audio, just image.Thank you for your help.
-
BlackBerry Smartphones Blackberry SMS - recognizing only messages not sent
Hi all. I have a problem with my bb sms service: when I write and send a text message, the Green message composer icon remains in my Inbox - my blackberry does not seem to recognize that I sent the message. Can someone please? Thank you