I try a checkdisk
I try a checkdisk and get the message "Windows cannot check the drive while it is in use." Try to initialize checkdisk at startup (as advised by message). I get the message that "checkdisk cannot run because of recently installed software. Restoration and earlier version. "I have this and get the same messages. Any suggestions?
Hi,
Thanks for posting your question in the Microsoft Community.
From descriptions of the question, it seems that you are unable to run the check disk in your computer.
I imagine the inconvenience that you are experiencing. I'll help you fix the problem.
I see that you have after most of the troubleshooting steps to perform the disk check and are still unable to do so, but I suggest you to check the disk in the command prompt by using the Windows recovery environment (WinRE) to diagnose and solve problems from the link below.
What are the system recovery options in Windows 7?
:
http://Windows.Microsoft.com/en-CA/Windows7/what-are-the-system-recovery-options-in-Windows-7
Run the commands below
a. run Chkdsk in command prompt with administrative rights.
b. CHKDSK x: /F /R (this command will perform a complete analysis (including bad sectors) and an attempt to remedy)
Important: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.
For reference:
CHKDSK:
http://TechNet.Microsoft.com/en-us/library/bb491051.aspx
I hope that the information above helps you.
Your response is very important for us to ensure a proper resolution.
In the future if you fall on any question relating to Windows, please do not hesitate to post your request here on Microsoft Community, we will be more than happy to help you.
Tags: Windows
Similar Questions
-
Windows Vista fails to update even though she says she did it.
I get the message trying to update Windows Vista. I enable it and it seems to work fine. Shortly, he says that he has the same updates. It is as if he is not kept up-to-date, or least acknowledge that it has updated.
I looked for a solution and I came across something that may be a conflict, but am not sure. I run a wireless HP printer and Vista had some issues with this.
Here are the updates of security, and I want to assure you that I have the latest versions.
What should I do?
-Peter
Peter
It is possible that updates that you download where corrupted there are a few tools that can repair or remove them from the system so that you can redownlod them. Sometimes the file or drive may be hit if she isn't bad corrupt. I suggest that you BACK UP all your data. Here are some things that you can try the CHECKDISK, SCAN SFC
SFC SCAN: http://support.microsoft.com/kb/947595
Download CHECKSUR: http://www.microsoft.com/downloads/details.aspx?FamilyID=32978546-8108-408f-b78e-0e95eff14c92&DisplayLang=en
Please let us know Justin M. Microsoft Support Engineer Answers visit our Microsoft answers feedback Forumand let us know what you think.
-
Hello world. IM new here.
I would like to ask questions about the allocation of diskMy drive HARD Ext (WD my passport) will not appear. so, I check in computer management, and my disk not allocated
When I try to assigned by the following method
It is said: the request could not be performed because of an i/o device errorPlease... is if everyone there a solution to this issue?
I tried to update the firmware, WD Essential, WD utilities
but this does not solve the problem...
When I try to checkdisk in promptcomand but I don't know how to put it, because the drive isn't there...Please help me...
Hello
This error may be coming because of unavailable storage required for the motherboard drivers. You can follow the steps one by one, mentioned below and check if that helps.
Method 1: Uninstall, and then reconnect the external hard drive. This method solves the problems where the currently loaded USB driver has become corrupt or unstable.
- Click Start, type Device Manager in the box Search
- Click Device Manager in the returned list.
- Click disk drives in the list of hardware
- Right click on the USB external hard drive with the question and click Uninstall.
- Once the hard drive is uninstalled, disconnect the USB cable.
- Wait 1 minute and then reconnect the USB cable. The driver should load automatically
- Look for the USB key in Windows Explorer
Note: Connection of your USB external hard drive to a non powered USB hub can cause a lack of sufficient power to operate the external drive. Instead, plug it directly into your computer.
Method 2: Install the latest Windows updates.
This method will install the latest drivers for your external hard drive USB device.
- Click the Start button, type Windows Update in the search box, and then click Windows Update in the results pane.
- Click find updates. When the scan finished, click optional review updates.
- Click the check box next to the update, and then click install updates.
- If you are prompted, read the license agreement, then click I agree.
- Follow the instructions on the screen to download and install updates.
- If you are prompted, restart your computer.
If your problem still exists, go to method 3.
Method 3: Reinstall the USB controllers. This method addresses the steps where the USB driver currently loaded became unstable or corrupted.
- Click Start, type device in the area Manager Search , and then click Device Manager.
- Expand Bus USB controllers. Right click on a device, and then click Uninstall. Repeat for each device.
- When finished, restart your computer. Your USB controllers will automatically install.
If your problem persists, go to method 4.
Method 4: Disable USB selective suspend framework. This method prevents your power off USB external drive.
- Click the Start button, type power management in the search box, and then click choose a power plan.
- Next to your currently selected plan, click Change Plan settings.
- Click change advanced power settings.
- Click in the box USBsettings, and then expand the USB selective suspend settings.
- Click on the area, and then click the menu drop down and select disabled.
- If you use a laptop, click the cell, and then click the menu drop down and select disabled.
- Click apply, and then click OK.
If this does not resolve your issue, go to method 5.
Method 5: Install the latest drivers for your motherboard chipset. This method updates the chipset of your motherboard drivers, so that your computer will use your external USB hard drive.
- See the documentation for your computer that will contain the name of the manufacturer of the motherboard.
- Visit your computer manufacturer's support Web site. For a list of the computer manufacturers support sites, visit: http://windows.microsoft.com/en-US/windows/help/contact-support/computer-manufacturers
(http://windows.microsoft.com/en-US/windows/help/contact-support/computer-manufacturers)
- Go to their Web site to find the appropriate drivers for your motherboard. For assistance, contact the manufacturer of your computer.
Please post with the State of the question.
-
Cannot create the image of the system under win7 64 bit
I can't create a system image of my entire system and save the image to another hard disk. I always get internal error ' 0 x 80070424. I here to detect my other readers (also tried to connect an external hard drive) i get presented with the internal error message. I don't stand less why I just do a clean install.
The installation went with a hitch.
System
Card mother "Gigabyte X48T-Dq6 with the latest version of the bios installed.
Core 2 duo quad core 2.6 Ghz cpu extrime.
4 GB of ddr3 RAM.
3 * 500GB & 1 * 1 TB hard drive
XFX Gforce 295 1.7 GB of ram
Ed xfi Platinum sound card
DVD - rw standardHi spyman1871,
Try the checkdisk Defragmenter and disk running from the command prompt.
Step 1: Checkdisk to run as administrator command prompt
To do:
1. go to start and type cmd in the search box.
2. right click on cmd in the list and select run as administrator.
3. click on Yes in the user account control prompt.
4. If you want to repair errors without scanning the volume for bad sectors, at the command prompt, type chkdsk volume: / f, and then press ENTER.
Note If one or more files on the hard disk are open, you will receive the following message is displayed:
Chkdsk cannot run because the volume is in use by another process. You want to schedule this volume to check the next time that the
the system restarts? (Y/N).Type there, and then press ENTER to schedule the disk check, and then restart your computer to start the disk check.
5. to fix the errors, look for bad sectors and recover readable information, at the command prompt, type chkdsk volume:/rand press ENTER.
Step 2: Run the command prompt Disk Defragmenter:
To do this, type the following in the command prompt window.
defrag c:-v,
where C is the drive letter. You can choose according to the reader like you would to run disk defragmentation.
Note: the command quick application shows no indication of progress, so be patient.
The Windows Live OneCare scanner cleaning will find and remove the invalid registry on your PC. Cleaning scan will check your registry and
Locate all items that can be deleted safely. You can then choose to delete all the items that the Analyzer detects or select the individual items for removal.http://OneCare.live.com/site/en-us/Center/cleanup.html
See also this thread with a similar problem for more ideas on how to solve this problem.
Kind regards
Amal-Microsoft Support.
Visit our Microsoft answers feedback Forum and let us know what you think. -
Recharging according to the printing software and get always the same error.
Hello
You must ask in the answers – Windows Forums for your version of Windows.
Answers - Windows Forums
http://answers.Microsoft.com/en-us/WindowsHow to ask a question
http://support.Microsoft.com/kb/555375==================================
Here is a troubleshooting guide for Windows 7 - Vista would be very similar.
Check with the printer manufacturer for updated drivers and support for known issues.
Check chan seen message here - one of the highest.
fixed spooler subsystem app stopped working
http://social.technet.Microsoft.com/forums/en/itprovistaprinting/thread/460f297a-dd66-4476-A176-542e1519ca3e==================================
Follow these steps in the kind of prerequisites:
Clean the General corruption and repair or replace the damaged/missing files.
Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to fix the system files of Windows 7 with the System File Checker
http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.htmlThen run checkdisk (chkdsk).
How to run check disk in Windows 7
http://www.SevenForums.com/tutorials/433-disk-check.html------------------------------------------------------
References to Vista also apply to Windows 7.
Go to the printer manufacturer's website and get the latest drivers - download - REGISTER - install yet. When loan
to install - make a right-click on the pilot - run as administrator.Also check with the manufacturer of your printer and forums support.
--------------------------------------
Use this method to clear the spooler and then uninstall and reinstall your printer (check with the manufacturer for)
the latest driver).Check Mr. Fixits here and if you use the other methods go back and try again later.
Problems of print and error - a Mr Fixit of printing
http://support.Microsoft.com/GP/printing_problemsSolve printer problems - a Mr Fixit
http://windowshelp.Microsoft.com/Windows/en-us/help/8c11977e-8244-408f-A036-7978a618d7a21033.mspx------------------------------------------------------
Logon as administrator
Start - type in the search box-> COMMAND - control to the top of the list and RIGHT CLICK – RUN AS ADMIN
You can copy and paste each line except those brackets and press ENTER after each.
net stop Spooler
(echo suppression of all print jobs)<-- you="" should="" see="" this="">-->
ping localhost n 4 > zero
del/q %SystemRoot%\system32\spool\printers\*.*
net start Spooler
(sound Done!)<-- you="" should="" see="" this="">-->
ping localhost n 4 > zero
Another way
http://4sysops.com/archives/how-to-cancel-a-print-job-that-hangs-under-Windows-Vista-and-XP/Check the print - DELETE/STOP queue all jobs - then right click on the printer - REMOVAL
http://windowshelp.Microsoft.com/Windows/en-us/help/bb6f81d9-4092-4ac8-9716-2bd008f513e11033.mspxIf you use Control Panel - Classic - printers
Try after unplugging your printer if necessary.
-------------------------------------------------------------Also check the spooler print and its dependencies and addictions Service.
Print Spooler service (see the following link BlackViper for Windows 7 default dependencies)
http://wiki.blackviper.com/wiki/Print_SpoolerBlackViper Windows 7 Service - default settings
http://www.blackviper.com/Windows_7/servicecfg.htmHow difficulty Windows Vista print spooler starts do not
http://www.ehow.com/how_4920100_vista-print-spooler-not-starting.html------------------------------------------------------------
Check this thread if necessary - to stop and erase the spooler
and here
I hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">->
I hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">->
-
just built a computer a week 7 there and installed. my computer currently has no installed updates. whenever I try to install updates (one of them) I get the bsod and need to restore several times, computer works fine until I turn it off.
the screen will change resolution 1280 x 1024 at ~ 600 x 800 for about five seconds then bluescreen when it spoil.
my initial error code: 100007e.
0000005,4843518, 3c3c628, 3c3be80. any help will be greatly appreciated.Hello
Drivers of suspects, including video, BIOS, drivers ChipSet at low altitude, antivirus and anitspyware/safety programs
and hardware issues including such as bad sitting cards, memory problems and wiring. Power supply
is a real possibility. Are the updates of Windows he chokes on driver updates - if so right click on
These and HIDE?When you get to the pilot and sections of the memory of the troubleshooter check the following message to
update drivers and memory test and then return to the troubleshooter if necessary.1000007E and 0000007E are the same
Cause
SYSTEM_THREAD_EXCEPTION_NOT_HANDLED bug control is a very common bug control. To interpret it, you must identify which exception has been generated.
Common exception codes are:
- 0 x 80000002: STATUS_DATATYPE_MISALIGNMENT indicates an unaligned data reference was encountered.
- 0 x 80000003: STATUS_BREAKPOINT indicates a breakpoint or ASSERTION was met when no kernel debugger was attached to the system.
- 0xc0000005: STATUS_ACCESS_VIOLATION indicates a memory access violation has occurred.
For a complete list of exception codes, see the Ntstatus.h file located in the directory Inc. of the Microsoft Windows Driver Kit (WDK).
Solve the problem
If you do not have to debug this problem, you must use certain basic troubleshooting techniques.
- Make sure you have enough disk space.
- If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
- Try changing video cards.
- Check with your hardware vendor for updates to the BIOS.
- Disable the BIOS memory options such as implementing caching or shading.
If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.
If exception code 0 x 80000003 occurs, a hard-coded breakpoint or assertion was hit, but the system was launched with the /nodebug. switch. This problem should occur infrequently. If it occurs repeatedly, make sure that a kernel debugger is connected and the system is booted with the Switch/DEBUG .
In case of exception code 0 x 80000002, the trap frame provides additional information.
If you do not know the specific cause of the exception, consider the following questions:
- Hardware incompatibility. Ensure that any new hardware that is installed is listed in the list of the products tested Microsoft Windows market.
- Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.
If a driver is listed by name in the bug check message, disable or remove that driver. Disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.
If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the service by starting the computer by using the recovery and then Console by removing the offending system service file.
Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x7E.
You can also disable memory cache BIOS may try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.
The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved .chk , which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation. You can solve the problems of BIOS by upgrading the version of the system BIOS.
=====================================================
This solving generic problems but it should help you resolve the issue however remember them ALL
This new material is very suspicious.Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.htmlHere are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during "blue screen of death," collisions
Displays information on all the "crash" of a table - free
http://www.NirSoft.NET/utils/blue_screen_view.htmlBlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.
You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
system installed by the manufacturer.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxYou can try a system restore to a point before the problem started when one exists.
How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html-------------------------------------------------------------------------
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).
Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
smile, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting, STOP error blue screen Vista
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
The Options or Vista recovery disk Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.htmlThis tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxI hope this helps.
Rob - bicycle - Mark Twain said it is good.
-
How to use transfer windows for xp to xp. When I plug usb computers are delivered to the top with the same screen and when I try to use the transfer to the new computer, it just said information gathering and sits for hours
Hello, welcome.
The process is automatic and the maximum transfer rate should be about 20 GB/HR. If the process crashes during that long of a time, it's probably because of something internal rather something you're doing wrong.For reference purposes, I included this link. It goes into the details of the migration from XP to Vista (and the basic steps you follow). The instructions are for migrating to Vista via the network, but you can easily follow the steps and choose a different option for your specific installation.http://www.windowsnetworking.com/articles_tutorials/migrating-Vista-using-Windows-easy-transfer.htmlFor both machines, I recommend you to prepare for the transfer using the following procedure:1. click on START > run2 type "msconfig" (without the quotes) and press enter3. go to the "Startup" tab and uncheck all the entries displayed4. click on 'Apply' at the bottom rightDO NOT RESTART YOUR COMPUTER AGAIN5. click on START > run6. Type "cmd" (without the quotes). Right-click on the result at the top of the menu START and select 'run as administrator '.7. type chkdsk /r and press enter8 allow the system to attempt disassembly of the volume9. allow the system to plan restarting10. restart your computer11 let checkdisk analyze the file system on your hard drive12. Once completed, perform the same steps on the other machine13. Once completed, repeat the transfer
Let us know what happensThank you!Ryan Thieman
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think. -
Computer will not start after windows checkdisk thing?
My office has gone through a few microsoft checkdisk thing today (16\11\2010), and after that it's over, my com could not start more.
It would be to start all the way until the logo Windows XP there and after loading was done and usually, it would be a blue screen with your user account, but however he just showed a black screen and I waited a certain 20 minutes and nothing happened.
Then, I tried to reboot 10 times over and always to the same black screen.
When I tried the thing Safe Mode would stop any loading at some point of the code, which is
multi (0) disk (0) rdisk (0) partition (1) \WINDOWS\system32\DRIVERS\agp440.sys
That's what was on my setup on my desktop that I accessed:
"Primary Master" > Hitachi HDP72502
Primary slave > no
Secondary master > HL - DT - ST GCE-852
Secondary slave > HL-DT-STDVD-ROMBasic version of the BIOS > V6.0
Revision of BIOS 3.25 23/09/2003Anyone know what is happening and how can I solve this problem?
In the Boot Options menu advanced F8, choose this option and describe the results:
Disable the automatic restart in the event of system failure
Let us know if you do not see this option in the Advanced Boot Options menu.
You will not get far if you can't start something, so if you have a CD/DVD player, do you have a bootable XP Recovery Console in order to have room for manoeuvre, boot on the CD, run chkdsk /r and then you can start solving the problem (instructions below).
You are once started in the Console recovery XP and after running chkdsk/r, then you will be able to see if KB324764 will help you.
Please provide additional information on your system:
What is your system brand and model?
What is your Version of XP and the Service Pack?
Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, Defender, ZoneAlarm, PC Tools, MSE, Comodo, etc..
If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.
This is not the same as recovery disks that may have come to a store to purchase the system.
You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.
The ISO bootable image file you need to download is called:
xp_rec_con. ISO
Download the ISO from here:
http://www.mediafire.com/?ueyyzfymmig
Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:
Here are some instructions for ImgBurn:
http://Forum.ImgBurn.com/index.php?showtopic=61
It would be a good idea to test your bootable CD on a computer running.
You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive. These adjustments are made before Windows tries to load. If you miss it, you will need to restart the system again.
When you start on the CD, follow the instructions:
Press any key to boot from CD...
Installing Windows... going to pronounce.
Press 'R' to enter the Recovery Console.
Select the installation that you want to access (usually 1: C:\WINDOWS)
You may be asked to enter the password (usually empty).
You should be in the folder C:\WINDOWS. It's the same as the
C:\Windows folder that you see in Solution Explorer.
The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.
For a list of the commands in the Recovery Console, type help at the command prompt.
Start by checking the integrity of your file system by using the chkdsk command.
In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.
Running chkdsk is fine, even if he finds no problem. It won't hurt anything to run it.
Assuming your boot drive is C, run the following command:
CHKDSK C: /r
Let chkdsk finish to correct the problems, he could find. It may take a long time for chkdsk complete or they seem to be "stuck". Be patient. If the HARD drive led blinks always, chkdsk is something. Keep an eye on the amount of the percentage to be sure that it is still making progress. It may even seem to go back sometime.
You must run chkdsk/r again until it finds no error to correct.
Remove the CD, and then type "exit" to exit the RC and restart the computer.
You have not to set the BIOS to boot the disk HARD since the CD won't be.
Do, or do not. There is no test.
I need YOUR voice and the points for helpful answers and propose responses. I'm saving for a pony!
-
try to uninstall programs, "Journal of instalation not found".
I would be very gratful if someone could help me... once again please! Yesterday, after the acquisition of the programe of thugs 'CYBERSECURITY' I came here asking if someone could help me to get rid of it, thanks to those who responded, unbelivably, I managed to get rid of it myself with system restore in safe mode (it may work for other people, I answered some telling them to try this) that I never thought would work , but, touch wood, looks ok now Ive cleaned it. I just have a problem now try to uninstall the programs that I got rid of the day, I acquired of cybersecurity. I guess it's because the restore point, I gave him too much. I want to get rid of these again, but every time I try to unistal them, he said: (Ghost Installer) "Not found Setup log" happens then "this program might not be properly uninstalled" it gives the choice 'Uninstall using recommended settings' or 'this program uninstalled corectly' when I click to uninstall using recommended, then goes back to "instalation log not found" again. I don't know that there is a very simple answer to that, unfortunately, I don't know much, just a little more before the program of thugs! would be very gratful for help.
Thank you
Sarah
Hello
If possible and not malware try to reinstall the program, so you can uninstall them.
For all THE tools here when possible - download - RECORD - go where you put them - click on - RUN AS ADMIN
(do not use RUN AS ADMIN for the program that you just want to load and then uninstall unless it takes and it is
not malware).A great tool to use is Revo
Revo Unintaller - free
http://www.revouninstaller.com/------------------------------------
In your cleaning have you run SFC/scannow, and then checkdisk?
Follow these steps to remove corruption and missing/damaged file system repair or replacement.
Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup
Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN
sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html================================
I would also like to do the following:
Spotlight utility Windows Installer CleanUp Utility
http://TechNet.Microsoft.com/en-us/magazine/2008.08.UtilitySpotlight.aspxDescription of the Windows Installer CleanUp utility
http://support.Microsoft.com/kb/290301Windows install 4.5 Redistributable
http://www.Microsoft.com/downloads/details.aspx?FamilyId=5A58B56F-60B6-4412-95B9-54D056D6F9F4&displaylang=enI hope this helps.
Rob - bicycle - Mark Twain said it is good. -
Dell technicians had me buy a new disk, Windows 7 OS, which I installed it yesterday. A few minutes before, a phone call came in saying they were calling from Microsoft and I wanted to scan for free because I bought a product at Microsoft. They had me download software teamviewer.com, ccleaner, malware, spyware superantii. They ran scans and said I was infected and I should buy these software packages for $79. Is this a real service of Microsoft? I still have these software on my computer, I have to delete them? What other threats may be present, if it is not a true service of Microsoft?
Hello
Avoid scams to phone for tech support
http://www.Microsoft.com/security/online-privacy/avoid-phone-scams.aspxScams by e-mail or web: how to protect yourself - understands what to do if you
think you've been scammed.
http://www.Microsoft.com/security/online-privacy/phishing-scams.aspxHow to recognize phishing e-mails, phone calls or links
http://www.Microsoft.com/security/online-privacy/phishing-symptoms.aspxIts a total scam. Uninstall their software, then perform a restore of the system back to before you
to install it. Change all your sensitive passwords at all sites - e-mail, Bank, credit cards and
others. (Do not do this on the infected computer and it would be better to do it on the)
phone or in person.)You can even restore your system to factory fresh to make sure their software is
do not breach your security. (Ways to re - install Windows Clean - remove all about)
the player therefore save all data before hand.)====================================================================
====================================================================In the United States, you can contact the FBI, Attorney general, the police authorities and consumer
Watch groups. Arm yourself with knowledge.The Internet Crime Complaint Center (IC3) is a partnership between the
Federal Bureau of Investigation (FBI) and the National White Collar Crime Center
(NW3C), funded in part by the Bureau of Justice Assistance (BJA).
http://www.ic3.gov/complaint/default.aspx
No, Microsoft wouldn't you not solicited. Or they would know if errors exist on your
computer. So that's the fraud or scams to get your money or worse to steal your identity.Do not fall for the fake phone Tech Support
http://blogs.msdn.com/b/securitytipstalk/archive/2010/03/09/Don-t-fall-for-phony-phone-tech-support.aspxAvoid scams that use the Microsoft name fraudulently - Microsoft is not unsolicited
phone calls to help you fix your computer
http://www.Microsoft.com/protect/fraud/phishing/msName.aspxScams and hoaxes
http://support.Microsoft.com/contactus/cu_sc_virsec_master?ws=support#tab3Microsoft Support Center consumer
https://consumersecuritysupport.Microsoft.com/default.aspx?altbrand=true&SD=GN&ln=en-us&St=1&wfxredirect=1&gssnb=1Microsoft technical support
http://support.Microsoft.com/contactus/?ws=support#TAB0Microsoft - contact technical support
http://Windows.Microsoft.com/en-us/Windows/help/contact-supportPhone scams
http://www.consumer.ftc.gov/articles/0076-phone-scamsLimit unwanted calls & Emails
http://www.consumer.ftc.gov/topics/limiting-unwanted-calls-emailsNational do not call registry for
https://www.DoNotCall.gov/===========================================================
===========================================================
Follow these steps carefully:If you need search malware here's my recommendations - they will allow you to
scrutiny and the withdrawal without ending up with a load of spyware programs running
resident who can cause as many questions as the malware and may be more difficult to detect as the
cause.No one program cannot be used to detect and remove any malware. Added that often easy
to detect malicious software often comes with a much harder to detect and remove the payload. Then
its best to be thorough than paying the high price later now too. Check with them to one
extreme overkill point and then run the cleaning only when you are sure that the system is clean.It can be made repeatedly in Mode safe - F8 tap that you start, however, you must also run
the regular windows when you can.TDSSKiller.exe. - Download the desktop - so go ahead and right-click on it - RUN AS ADMIN
It will display all the infections in the report after you run - if it will not run changed the name of
TDSSKiller.exe to tdsskiller.com. If she finds something or not does not mean that you should not
check with the other methods below.
http://support.Kaspersky.com/viruses/solutions?QID=208280684Download malwarebytes and scan with it, run MRT and add Prevx to be sure that he is gone.
(If Rootkits run UnHackMe)Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
Malwarebytes - free
http://www.Malwarebytes.org/products/malwarebytes_freeSuperAntiSpyware Portable Scanner - free
http://www.SUPERAntiSpyware.com/portablescanner.HTML?tag=SAS_HOMEPAGERun the malware removal tool from Microsoft
Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.
You should get this tool and its updates via Windows updates - if necessary, you can
Download it here.Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
(Then run MRT as shown above.)Microsoft Malicious - 32-bit removal tool
http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=enMicrosoft Malicious removal tool - 64 bit
http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=enalso install Prevx to be sure that it is all gone.
Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
Prevx - Home - free - small, fast, exceptional CLOUD protection, working with others
security programs. It is a single scanner, VERY EFFICIENT, if it finds something to come back
here or use Google to see how to remove.
http://www.prevx.com/ <-->-->
http://info.prevx.com/downloadcsi.asp?prevx=Y <-->-->Choice of PCmag editor - Prevx-
http://www.PCMag.com/Article2/0, 2817,2346862,00.aspTry the demo version of Hitman Pro:
Hitman Pro is a second scanner reviews, designed to save your computer from malicious software
(viruses, Trojans, rootkits, etc.). who infected your computer despite safe
what you have done (such as antivirus, firewall, etc.).
http://www.SurfRight.nl/en/hitmanpro--------------------------------------------------------
If necessary here are some free online scanners to help the
http://www.eset.com/onlinescan/
-----------------------------------
Original version is now replaced by the Microsoft Safety Scanner
http://OneCare.live.com/site/en-us/default.htmMicrosoft safety scanner
http://www.Microsoft.com/security/scanner/en-us/default.aspx----------------------------------
http://www.Kaspersky.com/virusscanner
Other tests free online
http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1--------------------------------------------------------
After the removal of malicious programs:
Also follow these steps for the General corruption of cleaning and repair/replace damaged/missing
system files.Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to fix the system files of Windows 7 with the System File Checker
http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.htmlHow to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run check disk in Windows 7
http://www.SevenForums.com/tutorials/433-disk-check.html-----------------------------------------------------------------------
If we find Rootkits use this thread and other suggestions. (Run UnHackMe)
======================================
If necessary AFTER THAT you are sure that the machine is clean of any malware.
How to do a repair installation to repair Windows 7
http://www.SevenForums.com/tutorials/3413-repair-install.htmlI hope this helps and happy holidays!
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="">-><- mark="" twain="" said="" it="">->
-
the print spooler stops when I try to print
Please help me with my printer!
I tried desperately to install an Epson WorkForce 615 on my computer, running Windows Vista 32-bit. Whenever I try, the print spooler stops and I can't move forward. I restart the print spooler and it stops again with each attempt. I tried every available quantity of advice that I could find online, to go into the registry and delete the files and enter cmd and stopping and restarting the spooler. I don't know what to do... Please help!
Hello
Do not forget to check with the support of the manufacturer of the printer, drivers and forums for known issues, because this issue is often
due to pilot errors.Check chan seen message here - one of the highest.
fixed spooler subsystem app stopped working
http://social.technet.Microsoft.com/forums/en/itprovistaprinting/thread/460f297a-dd66-4476-A176-542e1519ca3e===================================
If the above didn't help:
Use this method to clear the spooler and then uninstall and reinstall your printer (check with the manufacturer for)
the latest driver).Check Mr. Fixits here and if you use the other methods go back and try again later.
Problems of print and error - a Mr Fixit of printing
http://support.Microsoft.com/GP/printing_problemsSolve printer problems - a Mr Fixit
http://windowshelp.Microsoft.com/Windows/en-us/help/8c11977e-8244-408f-A036-7978a618d7a21033.mspx------------------------------------------------------
Logon as administratorStart - type in the search box-> COMMAND - control to the top of the list and RIGHT CLICK – RUN AS ADMIN
You can copy and paste each line except those brackets and press ENTER after each.
net stop Spooler
(echo suppression of all print jobs)<-- you="" should="" see="" this="">-->
ping localhost n 4 > zero
del/q %SystemRoot%\system32\spool\printers\*.*
net start Spooler
(sound Done!)<-- you="" should="" see="" this="">-->
ping localhost n 4 > zero
Another way
http://4sysops.com/archives/how-to-cancel-a-print-job-that-hangs-under-Windows-Vista-and-XP/Check the print - DELETE/STOP queue all jobs - then right click on the printer - REMOVAL
http://windowshelp.Microsoft.com/Windows/en-us/help/bb6f81d9-4092-4ac8-9716-2bd008f513e11033.mspxIf you use Control Panel - Classic - printers
Try after unplugging your printer if necessary.
-------------------------------------------------------------Also check the spooler print and its dependencies and addictions Service.
Print Spooler service
http://www.blackviper.com/WinVista/services/Print_Spooler.htmHow difficulty Windows Vista print spooler starts do not
http://www.ehow.com/how_4920100_vista-print-spooler-not-starting.html------------------------------------------------------------
Check this thread if necessary - to stop and erase the spooler
------------------------------------------------------
Clean the General corruption and repair or replace the damaged/missing files.Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228CheckDisk (chkdsk) runs at startup.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.htmlI hope this helps.
-
When I go into the control panel to change my settings for the mouse, I get the error "windows rundll.exe host has stopped working", therefore, you cannot change the mouse settings, how do I fix it? My mouse is out of control! :)
* original title - why windows will not host rundll.exe I would change my settings of the mouse? *
Hello
If you use 3rd party mouse drivers updated or reinstall those who, like Logitech, Microsoft
Wireless and so on.=================================================================
To solve the problems:
If your: Windows host process Rundll32 has stopped working
http://www.WinVistaClub.com/T40.htmlWhat is rundll32.exe and why it works?
http://www.howtogeek.com/HOWTO/Windows-Vista/what-is-rundll32exe-and-why-is-it-running/What is the suspicious Rundll32.exe process?
http://WindowsXP.MVPs.org/Rundll32.htm-----------------------------------------------------
Try these to erase corruption and missing/damaged file system repair or replacement.
Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup
Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN
sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
program generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html-----------------------------------------------------
If no joy trying to determine what is the cause:
How to troubleshoot a problem by performing a clean boot in Windows Vista
http://support.Microsoft.com/kb/929135
How to troubleshoot performance issues in Windows Vista
http://support.Microsoft.com/kb/950685Optimize the performance of Microsoft Windows Vista
http://support.Microsoft.com/kb/959062
To see everything that is in charge of startup - wait a few minutes without doing anything - then right
Click on taskbar - task manager - take a look at stored by - Services - process -.
It's a quick reference (if you have a small box left - show for all users, then
Check that).How to check and change Vista startup programs
http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.htmlA quick check to see who are loading is method 2 - using MSCONFIG then after a
a list of these here.
--------------------------------------------------------------------Tools that should help you:
Objects of process Explorer - free - find out what files, registry keys and other processes
have open, which DLLs they have loaded and more. This exceptionally effective utility will be
even show you who owns each process.
http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspxAutoruns - free - see what programs are configured so that it starts automatically when your
system boots and you log in. Autoruns is also the full list of registry and files
locations where applications can configure start automatic settings.
http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
Process Monitor - Free - monitor the system files, registry, process, thread and DLL activity
in real time.
http://TechNet.Microsoft.com/en-us/Sysinternals/bb896645.aspxThere are many excellent free tools from Sysinternals
http://TechNet.Microsoft.com/en-us/Sysinternals/default.aspx-Free - WhatsInStartUP this utility displays the list of all applications that are loaded
automatically when Windows starts. For each request, the following information
appears: product Type of startup (registry/Startup folder), Command - Line String,
Name, file Version, company name, location in the registry or the file system and more.
It allows you to easily disable or remove unwanted programs that run in your Windows
startup.
http://www.NirSoft.NET/utils/what_run_in_startup.htmlThere are many excellent free tools to NirSoft
http://www.NirSoft.NET/utils/index.htmlWindow Watcher - free - do you know what is running on your computer? Maybe not.
The window Watcher says it all, every window created by all programs that are running, the statement
If the window is visible or not.
http://www.KarenWare.com/PowerTools/ptwinwatch.aspMany excellent free tools and an excellent newsletter at Karenware
http://www.KarenWare.com/Hope these helps.
-
Try to run a 'error checking' and 'defragmentation' on my computer
Hello
My computer was slow, so I would like to run a 'error checking' and 'Defragmentation '.
When I try to run the "error checking" I get the following message: "the disk check cannot be performed because the disk check utility needs exclusive access to some Windows files on the disk. These files are accessible only by restarting windows. You want to schedule this disk check to occur the next time that you restart the computer? " I tried to restart Windows and check the disc again, but I still get the same message.
When I try to run a defrag, I get the following message: "Disk Defragmenter has detected that Chdsk is expected to run on the volume: HP_PAVILION (c)." Please run Chkdsk /f.' I've repeatedly said no to checkdisk start in the previous paragraph, but I always get these messages.
No information as to how I can solve this problem?
Thank you! Kara
Maybe you will need to follow the instructions more closely. If your repeatedly said 'NO', how it's supposed to run checkdisk?
Click to open the computer.
Right click on the hard drive you want to check, and then click Properties.
Click on the Tools tab, and then under error checking, clickCheck now. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
To automatically repair problems with files and folders that the scan detects, selectAutomatically fix file system errors. Otherwise, the disk check will simply report a problem, but not to fix them.
To perform a full disk check, select search and attempt to recover bad sectors. This scan is trying to find and repair physical errors on the hard drive itself, and it may take much longer to complete.
To check for errors file and the physical errors, select both automatically fix file system errors andScan for and attempt recovery of bad sectors.
Click Start.
Depending on the size of your hard disk, this may take several minutes. For best results, do not use your computer for any other tasks while it checks errors.
Note
If you select automatically fix errors of system file of a disk that is used (for example, thepartition as containsWindows), you will be asked to reschedule the disk check for the next time you restart your computer.
-
CD drive won't read, finished with the error on the page, I can't transfer songs to my iphone
Hello
Not completely sure what you are doing to try to see the pictures or to transfer the songs. For the iPhone
check with their support and the forums.iPhone Support
http://www.Apple.com/support/iPhone/iPhone Forums
http://discussions.Apple.com/category.jspa?categoryID=201==================
For the CD/DVD:
Follow these steps to remove corruption and missing/damaged file system repair or replacement.
Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup
Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN
sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html--------------------
Step 1: Please do all the same underneath if you did some before as is often total
a process that solves the problem.Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
below.
Then, work your way through these - don't forget the drive might be bad, could be a coward
cable or slight corrosion on the contacts (usually for a laptop) and other issues.Your CD or DVD drive is missing or is not recognized by Windows or other programs
http://support.microsoft.com/kb/314060 - a Mr FixitTry this fix manually if the Fixit 314060 does not work
http://www.pchell.com/hardware/cd_drive_error_code_39.shtmlYour CD or DVD drive is missing or is not recognized by Windows or other programs-
a Mr Fixit
http://support.Microsoft.com/kb/982116The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
for Windows Vista
http://support.Microsoft.com/kb/929461When you insert a CD or a DVD, Windows Vista may not recognize the disc
http://support.Microsoft.com/kb/939052Your CD or DVD drive cannot read or write media - A Mr Fixit
http://support.Microsoft.com/GP/cd_dvd_drive_problemsCD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
Vista installation after booting from the DVD (AHCI)
http://support.Microsoft.com/kb/952951
Drive CD - R or CD - RW Drive is not recognized as a recordable device
http://support.Microsoft.com/kb/316529/Hardware devices not detected or not working - A Mr Fixit
http://support.Microsoft.com/GP/hardware_device_problemsAnother possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
ends. Remove and replace, do not just tight. For laptops, you can often clean power and
contacts data with a pencil eraser.Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
manufacturer of device to see if there is a firmware or drivers for your drive if necessary.===============================
Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
do it right.Did you follow the Troubleshooting Guide for the reader who still does not work? There are
the entries in registry that the troubleshooter does not solve and those who "might" be the cause.Check with your Maker system and a device for the two possible firmware updates and
the correct registry entries for your car.Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
the parameters.HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}
-----------------------------------------------------------------------
You can probably find more info here and maybe even the exact registry for your CD/DVD settings
drive from someone with the same model.Forums - a lot of expert real help
http://Club.myce.com/CD/DVD units
http://www.myce.com/storage/Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
nothing change) - find the DevManView device and then make a right click on it free in RegEdit.DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
devices and their properties in flat table, instead of the tree viewer
http://www.NirSoft.NET/utils/device_manager_view.htmlI hope this helps.
Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.
-
Sidebar does not work. have the .ini file, but when I try to open it States, "sidebar is going to end." Any help
Hello
Try these to erase corruption and missing/damaged file system repair or replacement.
Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup
Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN
sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html--------------------------------------------------------------
Then proceed as follows:
How to restore the sidebar of Windows?
http://support.Microsoft.com/kb/963010If necessary to do it manually:
Logon as Admin - Start - type in the area of research-> COMMAND - find top - RIGHT CLIC on it-
RUN AS ADMINReplace C:\Program Files\Windows Sidebar by copying and pasting this command->
CD C:\Program Files\Windows Sidebar
Press enter (this is assuming that your sidebar is on C:, otherwise use the letter of the drive is on)Guest should be--> C:\Program Files\Windows Sidebar >
Then copy / paste each of them following their tour each come into
regsvr32-u sbdrop.dll
regsvr32-u wlsrvc.dll
regsvr32 atl.dll
regsvr32 sbdrop.dll
regsvr32 wlsrvc.dll
Sidebar should now work
Type in the search-> Sidebar box - find top - make a RIGHT CLIC top - RUN AS ADMIN
========================================================
Close the sidebar for that.
Something else for the settings.ini - run AutoRuns and look at the entries SideBar - Gadget
are there pointing to no longer like those temp files or uninstalled or
gadgets run do not? Those who will reflect the "yellow icons" on the left side and the
folder/files do not exist. If so right click on them and delete - Reboot.Autoruns - free - see what programs are configured so that it starts automatically when
your system boots and you connect. Autoruns also shows you the complete list of the registry and
locations where applications can configure Auto-start of the file settings.
http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
I hope this helps.Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.
Maybe you are looking for
-
Hello http://www.tomshw.it/Refresh the page.I click on the bookmark of FF http://www.tomshw.it/ and I can refresh the page without problem.Why if I refresh the page by clicking on the icon refresh (right of the url bar) the page scrolls down?After up
-
The user complains that his computer crashes from time to time and today he had planted 3 times. It's data only kernel panic I. Can you see something interesting in this kernel panic that will help me to solve the problems? Anonymous UUID: Thu Apr 21
-
Cannot start Journ.E Touch
Hello. My Journ.E will not start. Stay with the Toshiba logo and the OS is not running. Tried to update the firmware, but maintains the 'update' and do anything anymore. A tip?
-
I put openintabs to true, but it still does not; Win7/64 ffox 3.6
running win7/64 ffox 3.6; I have browser.search.openintab true value but is still does not work. I have to right click and select open in a new tab.
-
How to fix my Recycle Bin corrupted? My Recycle Bin is corrupted, when I try to remove a program, it removes only half or parts of it.